Search Documents

That gold will dissolve in sodium hyposlphite solutions is known from the lixiviation of silver and gold ores.The gold will dissolve only in small quantities. According to Stetefeldt, if gold leaf is treated for a time with sodium hyposlllphite solutions of varying strengths solution takes place in every instance, the deviation in quantity being very slight.In order to form hyposulphite double-salts, the gold must become oxidised, the oxygen being derived from the air absorbed by the solution. Consequently, it is the quantity of free oxygen in the solution by, which the reaction is determined, as for one equivalent of gold dissolved one equivalent of caustic soda is set free.

Jan 1, 1901

By P Lilly

Blasting is the primary comminution process in most mining operations. This process involves the highly complex and dynamic interaction between two main components. The first is the detonating explosive and the second is the rock mass into which the explosive is loaded. The mechanical properties of the rock material (such as dynamic strength, tensile strength, dynamic modulus and fracture toughness) are important considerations in understanding the blasting process. However, it is the characteristics of the geological defects (joints, foliation planes, bedding planes) within the rock mass that ultimately determine how effectively a blast performs in terms of fragmentation, all else being equal. The defect characteristics include, but are not limited to, their orientation, spacing, and mechanical properties. During the blasting process, some of the geotechnical characteristics of the rock mass are substantially changed. From the blasting outcome point of view, the most notable and important is the change in fragment size distribution that the rock mass undergoes. The pre-blast in situ defect-bounded block size distribution is transformed into the post-blast muckpile fragment size distribution. Consequently, it is fundamental to our understanding of and ability to predict the blasting process that both the blastability of a rock mass and its transformation into the fragment size distribution can be appropriately quantified.

Jan 1, 2001

Two continuous computer controlled, remote air analysis (RAA) systems operate at The Zinc Corporation, Limited (ZC) to give early warning in case of an underground fire at ZC or New Broken Hill Consolidated Limited (NBHC) mines. Air drawn from underground sampling points via a tube bundle system is analysed for carbon monoxide and carbon dioxide. An alarm is sounded if the concentrations of these gases exceed bench mark figures.

Jan 1, 1983

By Napier-Munn T. J, Morrison R. D, Moloney M. J, Corrans I. J

A dynamic simulator for CIP / CIL gold recovery plants has been developed at the Julius Kruttschnitt Mineral Research Centre within a collaborative, industrially - funded AMIRA project and with the participation of the Western Australian School of Mines. The simulator incorporates kinetic models for the leaching of gold from ore and its adsorption onto activated carbon, and the residence time distributions of the leach liquor, pulp solids and carbon in the circuit. Features of the simulator include the effects of gold loading distributions on both the ore and carbon on reaction rates, and the difference in residence time distribution between the leach liquor and pulp solids. The simulator allows for the estimation of kinetic model parameters from full scale applications, as well as some scale - up of parameters from laboratory batch tests. The laboratory tests were conducted at the WASM as part of the collaborative research project. The simulator can operate in both steady - state and dynamic modes, and has potential applications in design, optimisation and control of CIP / CIL plants.

Jan 1, 1991

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed. The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences: (i) a two-ply sequence with a lower vitrite-rich and an upper vitrite-poor ply; (ii) a two-ply sequence with a lower vitrite-poor and an upper vitrite-rich ply; and (iii) a four-ply sequence of 3 plies with vitrite-plus- clarite decreasing upwards, terminating in a vitrite- rich ply. The third basic sequence was very similar to a succession described for some British Carboniferous coals. Eighty per cent of the Australian Permian coal seams studied began with the first (i) basic type of sequence and are interpreted as originating in peat- forming areas which became progressively drier. More than half the seams were formed in an area with a stable depositional surface level which was subject to oscillations of small amplitude.. Many (30%) were formed in an area with a steadily rising depositional surface level.

Jan 1, 1969

By Jia X

Three-dimensional microscopic modelling techniques involving specific calculations based on direct computation of the Brownian, van der Waals, Born, electrical double layer repulsion, bulk, hydrodynamic and external forces (gravity, magnetic etc) acting on and between each particle in a mineral dispersion are now feasible using advanced computer processor architectures. This contribution surveys the hardware requirements, the advantages and limitations of the approach for enabling prediction of dispersion behaviour a priori. The notion of developing a generic particle simulator, akin to the use of molecular modelling in the area of drug design, based on inputting process-relevant data (solution chemistry, mineral solids properties, hydrodynamics etc) is discussed. The methodology is illustrated with application examples involving: predictions of coagulation of mineral fines; shape and size of magnetically-flocculated hematite; and the kinetics of fouling of membrane surfaces and walls.

Jan 1, 1993

By M Cooksey, Z Zhu, N Langrené, W Chen, T Tarnopolskaya

"Dynamic decision-making can significantly increase the value of mining projects and deliver better sustainability outcomes under conditions of uncertainty. Despite its benefits, dynamic decision-making is rarely used by the mining industry, possibly because of the complexity of the algorithms used to make sequential decisions under uncertainty and difficulties in visualising the optimal strategies. To achieve better outcomes in practice, decision-makers in industry would benefit from a tool that would help them to understand and implement the results of the analysis.CSIRO is developing innovative dynamic decision support tools that include an intuitive graphical display of the boundaries between the regions of different optimal decisions, which would significantly assist optimal sequential decision-making under uncertainty. The dynamic decision support tool is based on novel stochastic optimal control methodologies that can be used to optimise decisions in situations with multiple uncertain variables and decisions (Tarnopolskaya, Chen and Bao, 2015; Chen et al, 2015; Langrené et al, 2015). The types of market uncertainties that can be considered include commodity prices, interest rates and exchange rate, while the key orebody uncertainties include the reserves, boundaries between ore types and even geometallurgical parameters.The dynamic decision support tools have a number of benefits and can be used to:construct optimal operational strategies and to optimally manage resources projectsgain insight into optimal strategies under different market conditions and project settings compare expected project values under different project settings and to select the setting that provides best sustainability outcomes.This extended abstract demonstrates the use and benefits of the dynamic decision support tools using a synthetic case study of a gold mine.CITATION:Chen, W, Langrené, N, Tarnopolskaya, T, Zhu, Z and Cooksey, M, 2016. Dynamic decisions under uncertainty – a case study on a gold mine, in Proceedings Life-of-Mine 2016 Conference, pp 20–23 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

Having worked as a consultant for most of his 40-year working life, mostly as a mineral property valuer, the author has seen many poor valuations. Most were valuations of exploration tenements where the selection of the rather subjective, but necessary, geological inputs raised the main concerns. Those valuations involving iron ore prospects raise particular problems due to the special characteristics of such deposits. Iron ore is more like an industrial mineral rather than precious or base metals and Reserves are determined not by a traditional cut-off grade but by customer specifications. This is intended to be an overview/keynote paper on the current state of the growing (yet consolidating) Australian Iron Ore industry. It has now moved beyond Western AustraliaÆs æPilbara Big TwoÆ of Rio/BHPB (with the emergence of the irrepressible FMG and Hancock Prospecting) to include the YilgarnÆs æMidwest ManyÆ (including US re-entrant Cleveland Cliffs through Portman) and projects in other States. Ore types have moved from haematite Brockman to martite-goethite Marra Mamba (including the RobeÆs mesas and below water table Yandicoogina CIDs) and magnetite ore types. There are DSOs and secondary process feed. Mineral valuers have to reflect today upon these and many other determinants of value when choosing the most appropriate methodologies to adopt when technically assessing and valuing exploration tenements containing iron ore. Set against a frame work of the JORC Code (2004) and VALMIN Code (2005), the general valuation issues involved in using the cost methods (eg multiple of exploration expenditure), market methods (eg comparable sales, rules-of-thumb and joint venture terms) and income methods (eg synthetic discounted cash flow (DCF)/net present value (NPV) modelling) are discussed. Relevant factors when valuing iron ore properties are discussed, eg ore type, lump/fines ratio, stripping ratio, water table, impurities and grade, particularly the JORC confidence category of the identified mineralisation. Remoteness and access to existing rail infrastructure is a key consideration.

Jan 1, 2007

By Davies S. G, Jayaweera A

The oxidation of nickel sulphide and copper sulphide concentrates, and coal, has been studied under non-ignition and ignition conditions using Differential Thermal Analysis (DTA) and Thermogravimetry (TG). The non-ignition reaction was favoured by slow heating rates < 10°C min-1), low masses < 10 mg) and an air atmosphere. Under these conditions, the typical stepwise oxidations of the various sulphide minerals present in the concentrate were observed as resolved exothermic peaks in the DTA curves and weight losses in the TG curves. Above a heating rate of 10°C min-1 , sample masses in excess of 10 mg and an oxygen atmosphere, an ignition reaction was induced, as indicated by a major high energy exotherm in the DTA curve and a major rapid weight loss in the TG curve. The ignition temperatures of the minerals under ignition conditions, found for 15 mg samples heated at 20°C min-1, were 434°C for the nickel sulphide concentrate, 372°C for the copper sulphide concentrate, and 230°C for the coal. By plotting a curve for mass against ignition temperature at constant heating rate and extrapolationto zero mass, a value of 470°C was obtained for the mass independent ignition temperature of the nickel sulphide concentrate. Ignition temperatures and extents of reaction at various temperatures were obtained using the TG technique in a novel manner which produced heating rates of 4500°C min-1. Under ignition conditions, the oxidations approximate to flash smelting conditions.

Jan 1, 1985

By Harbort G. J

Jameson cell pilot plant trials were conducted in a number of areas in the Red Dome gold/copper flotation plant during 1991. The aim of testwork was to reduce the amount of cyanide soluble copper reporting in tailing to the gold leach plant, and hence reduce cyanide consumption. A number of these tests were conducted in parallel with conventional flotation columns. Laboratory tests were conducted to simulate the performance of the existing plant when compared with the addition of the Jameson cell allowing an extra sulphidising phase. This paper reviews the comparison of the Jameson cell and conventional columns in recovering cyanide soluble copper, while maximising copper concentrate grade. Key parameters that are investigated are residence times, air/pulp ratios, superficial gas recoveries and size by size recoveries. A brief comparison of performance of the Jameson cell and column in the controlled potential sulphidisation process is also presented. An estimation of the reduction in cyanide consumption is given.

Jan 1, 1992

By Crellin D, Reed SM

The paper presents details of borehole instrumentation schemes for the purposes of monitoring rock and fill deformations associated with groundwater in underground and surface coal mines. The instruments are described which measure rock mass displacements, permeability changes and alterations to hydrology. Methods of installation are detailed and the applicability of instruments discussed. Reduction and interpretation of results are detailed.

Jan 1, 1988

Prior to 1980 the thought of the occurrence of high-level epithermal gold mineralisation occurring in eastern Queensland would have been more of a dream than a reality. In a world-wide sense the understanding of the processes and tectonic settings for epithermal gold were only beginning to be developed. Although epithermal gold deposits had been mined in the past in Queensland the significance of these deposits in a regional sense had not been appreciated. A number of companies had made cursory examinations of epithermal regions in the Mt Coolon and Cracow regions. Since the mid 1980's the search for epithermal gold mineralization in Queensland was truly on and over 30 tonnes of gold from this style of deposit has been discovered.

Jan 1, 1989

By J Koppe, J F. Costa

A fundamental error of sampling occurs when a sample is extracted from a larger mass of ore or lot. The act of sampling requires that all particles belonging to the lot have an equal chance of being extracted. This type of sampling is called unbiased sampling. The sampling equipment (herein referred to as the sampler) should be constructed with some additional mechanical characteristics to guarantee that the samples will be unbiased. Samplers, extracting increments from a continuous flow, such as a conveyor belt, collect aliquots at regular time intervals. These time intervals relate to the number of aliquots extracted from a given mass of lot, whilst passing through the continuous flow. The frequency of extractions will influence the precision or the error of the sample (integration error). Further, the ore variability influences the amount collected from the continuous flow. Normally, the sampling protocol utilised is designed for the extractions obtained from the conveyor belt, omitting any error committed during this operation, ie the error of extracting from the continuous flow. This study aims to analyse the error of sampling a continuous flow by using a variogram with added on auxiliary functions. Each different piece of material passing through the flow will exhibit a distinct temporal variogram, which should influence the frequency of the samples being extracted for each chosen sampling error. The methodology used is presented in the form of a case study from a coal processing plant.

Jan 1, 2005

By Fuerstenau MC

Zinc cementation and carbon adsorption are both presently used for precious metals recovery from cyanide leach solutions. Each of these techniques exhibits unique processing features which renders them suitable to treat solutions with different properties and in different applications. In this study, the two processes are reviewed and compared. Operating data from a number of Merrill-Crowe precipitation and carbon adsorption plants in North America have been obtained and used in this analysis. The relative capital and operating costs for the two processes have also been considered.

Jan 1, 1993

By M Magee, D Way

The Mount Isa Copper Concentrator was commissioned in 1973. In 1991, two autogenous grinding mills were installed replacing two stages of crushing, one stage of rod milling and one stage of primary ball milling. The cyclone overflow P80 of the secondary ball milling circuit was reduced to 120 microns due to the increased operating power in the AG/SAG mill circuits. A study of the mineralogy of the milled products and the plant flotation recovery indicated that the installed secondary grinding energy was more than what was required for adequate liberation of the chalcopyrite and half of it had potential for more effective use elsewhere. Halving the secondary grinding energy meant only one of the two secondary ball mills would be needed. The predicted saving in operating cost of one less ball mill was more than two million dollars per annum. This paper summarises various plant trials that were conducted in the Copper Concentrator to decommission one of the two secondary ball mills.

Jan 1, 2004

By J Zanganeh, M Ajrash, B Moghtaderi

Application of thermal oxidation is considered a promising technique in reducing fugitive methane gas from ventilation air methane (VAM). A typical thermal oxidiser operates with diluted methane and converts it to less potent greenhouse gases. However, having a thermal oxidiser in the vicinity of the coalmine exhaust shaft is a major safety concern as its high operation temperature increases the likelihood of accidental fire and explosion. The aim of this study is to investigate the application and effectiveness of side venting technique in reduction of deflagration consequences caused by methane gas. To address this importance a series of experiments were conducted on a detonation tube designed and fabricated as part of larger scale VAM Abatement safety project. The experimental work was carried out into two stages: examine the flame and explosion properties in a large-scale detonation tube to get reliable data; and then design and employ a venting system into the detonation tube to verify the effectiveness and performance of the venting against the flame and explosion.Results corresponding to this study show that the side vent duct with venting coefficient magnitude of 37 had a significant influence on methane flame deflagration and the explosion characteristics. The maximum pressure rise at the detonation tube reduced approximately 20 per cent to 32 per cent by applying the side venting duct. Also, the data shows that the venting damped the pressure oscillation after the flame deflagration which eventually reduced the system instability. Finally, by applying the venting technique the expected level of damage due to the dynamic pressure reduced to the level of limited building damage.CITATION:Ajrash, M, Zanganeh, J and Moghtaderi, B, 2017. Application of side venting technique in mitigation of methane – air explosion and flame deflagration in ventilation air methane, in Proceedings Australian Mine Vent Conference 2017, pp 153–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

The variation of austenitic grain size with temperature for the steels XKSlSO and XK9261 was determined using the vacuum ctching technique.It is shown that the effect of temperature on the mean grain intercept is relatively small, up to approximately 950°C. Above this temperature the rate of increase of grain size rises sharply.Within the limits of the 1-4 hr vacuum etching times used the effect of time at temperature is relatively small on the ASTM grain size of the steels.

Jan 1, 1967

By Brown D. N, Troth D. A

Large blast furnaces demand high standards of preparation of feed materials which must meet tight specifications of chemical and physical quality. Measurement of these factors must be expeditious but the nature of the coke, sinter, ores and fluxes and the large tonnages involved requires substantial mechanical sampling plant. The equipment, its operations, and its problems, associated with the 5000 t.p.d. No.5 blast furnace at Australian Iron and Steel Pty. Ltd., Port Kembla, are described and the efficacy of chemical blending achieved in the ore blending yards and sintering operation, is reported.

Jan 1, 1976

By Weller K. R, Trahar W. J

The Mount Lyell Company treats some 2.3 million tonnes of ore annually, mined from a number of orebodies on the field. Blended ore is essentially a quartz-sericite schist containing about eight per cent of pyrite and three per cent of chalcopyrite. Four-stage crushing and two-stage ball milling are followe by selective flotation for copper. Pyrite is recovered from the coarse fraction of dopper circuit tailings. A detailed survey involving examination. of 82 samples provided information on the size- by-size behaviour of the principal ore constituents throughout the grinding, copper flotation and pyrite flotation sections of the circuit. Results for the copper and pyrite flotation sections are presented in the paper, and it is shown that over half the copper reporting to the final tailing (5% of copper in the feed) is plus 100 microns and that the major pyrite loss is in the desliming cyclone overflow. These data proVide a basis for assessing potential methods of circuit optimisation.

Jan 1, 1977

By A Lu, C Wang

The natural semiconducting mineral rutile and sphalerite exhibited highly photocatalytic activities on degradation of methyl orange under visible light irradiation. The isomorphous substitutions of host metal ions by foreign ions and other defect states in natural semiconductors altered the band structure, decreased the intrinsic band gap, and then made them very attractive for solar energy utilisation. Our study indicated that natural semiconductor minerals might be suggested as a new class of cost-effective and solar light-responsive photocatalyst.

Jan 1, 2008