Search Documents

By S Bandopadhyay

The seasonal fluctuations of the dust content in Arctic mine environments and the environmental variables affecting the intensity of dust production are qualitatively well known, but quantitative models that allow simulation and prediction of dust generation and the effects of engineering control of thermal regime on the mine environment are still non-existent. In Arctic mines, the migration of moisture in the surrounding rock mass releases fine dust by freeing it from the ice matrix allowing it to escape into mine airway. The migration of moisture is the direct cause for the production of mine dust and heat is the primary driving force. This paper examins the heat and moisture exchange between the ventilation air and the surrounding rock mass in frozen ground, placer mines in the Arctic. Based on the simulated results of a coupled heat and mass transfer problem with phase change, methods of dust control have been identified for mines in the Arctic.

Jan 1, 2005

By N Khalili, J Zhao, G F. Zhao

Toppling failure of a jointed rock slope was studied by using the distinct lattice spring model (DLSM). Compared with the classical discrete element model, the DLSM has the advantages of free calibration of micro-mechanical parameters and easy to represent discontinuities, and is more computationally efficient. In this work, the DLSM was used to investigate the toppling failure of jointed rock slopes. The numerical simulation was verified against experimental data from a centrifuge model test on a jointed rock slope. Both the horizontal deformations and failure pattern observed in the centrifuge test were reasonably reproduced using the DLSM. Then, the mechanism of the flexural toppling failure was studied numerically by using a parameter analysis. Finally, some insights were derived that may be useful for practical engineering.CITATION:Zhao, G F, Khalili, N and Zhao, J, 2014. Application of the distinct lattice spring model on toppling failure of a jointed rock slope, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Henderson J

Iron ore samples selected from the Deepdale, Iron Prince and Mt. Newman ore bodies have been pelletised on a pilot scale plant and subsequently reduced under laboratory conditions by hydrogen or carbon monoxide. Pellets approximately 1 cm in diameter have been reduced by hydrogen over the temperature range 5000- 900¦C and the results examined by thermogravimetric, microscopic, electron probe and x-ray techniques. After an initial time delay it was found that up to 95% reduction the rate of reduction could be described by a transport con- trolled porous model, in which the effective diffusivities of hydrogen in theòpr¦duct layer and the reaction zone are filar. Independent measurements of effective diffusivity supported the values obtained from the reduction data. ve 95% reduction the rate decreased markedly due to the formation_of retained wustite or fayalite. Comparison with reduction by carbon monoxide over the temperature range 7500 - 900¦C showed that the rate eduction by carbon monoxide was approximately five times slower than the rate by hydrogen. The rate of reduction was found to be a function of the properties of the pellets, which may account for the ely conflicting results that have been obtained in previous investigation on porous pellets.

Jan 1, 1970

By J Hadjigeorgiou, T R. Stacey

A ground support system is a combination of individual reinforcement and surface support elements that work together to retain and contain the rock mass. The various elements are subjected to external loads and to interactive loading between individual ground support system components. This paper focuses on the challenges in determining the capacity and behaviour of mesh, recognizing that installed mesh can be subjected to several loading mechanisms. Field observations from underground hard rock mines demonstrate that there are multiple types of damage and modes of failure of mesh. However, these are difficult to reproduce in a laboratory environment. A critical review has shown that existing mesh laboratory testing rigs reproduce very limited loading conditions that may not be representative of underground conditions. This has significant implications in quantifying and extrapolating the performance of mesh to ground conditions. CITATION:Hadjigeorgiou, J and Stacey, T R, 2018. Challenges in determining the capacity of mesh, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 280–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Marwick PL

As part of its operations Hamersley Iron operates a heavy medium Concentrator to upgrade low grade, unsaleable iron ore to produce saleable lump and fines products. Firstly, the attempts at delivering a blended feed in both chemical and physical characteristics are presented. Improvements in blending controls are shown to have given process performance improvements. Secondly, improvements to the feed preparation section are detailed. These alterations are providing a much cleaner feed to the subsequent processing stages.

Jan 1, 1987

It is well documented that drill and blast outcomes affect the downstream mining processes of loading, hauling, crushing and grinding but it can also significantly impact on mine profitability via dilution, recovery percentage, lump generation (iron ore), fines generation (coal, iron ore), coal loss and final wall stability. Drill and blast must therefore be optimised to improve the overall profitability via positively impacting on productivity and saleable product generation. It is however, difficult to achieve this because of the complexity of the number of parameters that must be integrated and managed across the entire mine value chain, ie the concept of æMine to MillÆ. This paper highlights, via a simple case study, the need to have a mineÆs drill and blast system both in control (so that it is predictable to a high degree) and with minimal variability (so the design actually makes it into the field). This type of management control is essential prior to optimisation work being undertaken. The æTeam ApproachÆ is discussed to illustrate the methodology of achieving drill and blast optimisation. A case study is presented to illustrate the potential benefits of this approach which in this mine represented a 27 per cent reduction in powder factor with the downstream functions achieving higher productivity with the same or reduced maintenance costs. It is essential for Australian mineÆs to implement the appropriate management strategies and experienced personnel placement to ensure that their mineÆs drill and blast system is correctly managed to facilitate the optimisation of profit. Without this, the Australian mining sector will become increasingly uncompetitive.

Jan 1, 1999

By T Casten

Freeport IndonesiaÆs DOZ (Deep Ore Zone) mine is scheduled to commence production in the second half of 2000. The DOZ will produce 25 000 tpd using mechanised block cave mining methods and will have a number of major improvements when compared to previous block cave mines in the district. The DOZ will have an independent and improved ventilation system, a flexible and efficient truck haulage system, and a more reliable crushing and conveying system than in previous underground mines in the district. This paper will describe the mine plan, haulage, and ventilation systems, and compare them to those used in other operations in the district.

Jan 1, 2000

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

By A R. Firth

The induration furnace for iron ore pellets was originally designed to process concentrates with high contents of magnetite. To support the use of haematite concentrates, internal fuel was added to the pellets in the form of ground coke breeze or anthracite. To ensure that the addition of coke breeze was not excessive, the ‘heat of magnetite equivalent’ or heat of magnetite equivalent (HME) relationship was developed, guaranteeing that the fi ring temperature requirements remained the same. However, this oversimplifi es the different reaction paths of magnetite and carbon in iron ore pellets. At fi ring temperatures, gas diffusion controlled reactions such as the combustion of coke, the calcination of carbonates and the reduction and oxidation of iron oxides can all occur in different parts of the pellet simultaneously. The interaction of these reactions produces a range of atmospheres across the diameter of the pellet that vary from oxidising at the pellet shell to reducing at the pellet core. Mathematical modelling and pellet fi ring experiments to preheat temperatures before quenching have shown that a higher proportion of coke relative to magnetite slows down the oxidation process, irrespective of temperature. A higher temperature, however, results in an increase in the rate of haematite reduction in the pellet core and a more reducing atmosphere, which could lead to different sintering rates in different parts of the pellet and shrinkage cracks forming. To observe these gas-solid reaction rates at a larger scale, the COREM pot grate has been updated with an additional oxygen analyser. This, along with other improvements, will allow better optimisation of straight-grate firing cycles for different pellet compositions.

Jul 11, 2011

Those developing or planning a new mining operation base their financial projections on amounts of gold produced as soon as practically possible. The choice and ongoing operation of mobile plant figures significantly in their projections. The implications of mobile plant selection are not always clear - until its too late.Our 'typical' gold mine would be a mine processing 800,000 tonnes of ore per annum, producing 37,000 ounces of gold with a life of mine of 10 years. Overburden layers are only evident in the first two years of operation.The pit will eventually, after some 5 years of mining, be some 300 metres deep, but confined to a mine radius of 2 kilometres.

Jan 1, 1986

By A E. Waltho, W J. Shaw

Predicting the physical characteristics of various ore types has for long been a difficult problem during mining. Grade control practices tend to concentrate on the chemical grade of the ore. Estimation of physical characteristics such as beneficiation behaviour is commonly limited to the simplistic application of historical averages. Large amounts of geochemical data are often gathered during the exploration and mining stages of a project, especially in ferrous and base metal deposits. In addition to the elements of principal economic interest, samples are often analysed for suites of gangue constituents to determine whether the mineralisation lies within target specifications. This multi-element data is often put to no other use than this simple chemical classification, yet it may present the geologist or metallurgist with valuable insights into the mineral content and physical characteristics of the deposit. Normative mineral estimates have been used as a method for characterising igneous rocks for almost 100 years. The method establishes and applies a set of sequential rules, by which the chemical components of a sample are assigned to mineral components. Provided that it is possible to make some realistic assumptions about the mineral species likely to be present in a rock unit or deposit and their paragenesis, this approach can be extended to a variety of mineral deposits. The geochemical data that are routinely collected when, for example, drilling iron ore and base metal deposits, can be used to derive estimates of normative mineral content. These estimates can be used to characterise physical or metallurgical aspects of the ore, such as density, beneficiation behaviour and metal recovery. This paper examines the application of normative mineral estimates to a variety of practical resource characterisation problems. The potential for predicting the lump and fines proportions of iron and manganese ores is also discussed.

Jan 1, 1999

By M Khanal, J Qin, B Shen, Y Duan, X Luo

Gaining confidence in interpreting rock and strata properties of the coalmine roof is necessary for design, maintenance, modelling and optimisation of roadways supports. One of the key causes of roadway instabilities experienced in underground coalmines is an extreme variable nature (thickness, competence, discontinuities etc) of the coalmine roof. Normally, the thickness and strength of the roof are characterised with the geotechnical and geological data gathered from exploration boreholes, which are drilled often at considerable distances apart. This limited data cannot capture localised geological variations in the coalmine roof. With this background, this paper explores feasibility of using measurement while drilling concept to perform geotechnical characterisation of the coalmine roof. The parameters, for example, penetration rate, rotary speed, torque, sound, vibration, obtained during the drilling process can provide valuable insights into geotechnical properties. The paper describes the progress of the experimental work conducted at the laboratory on synthesized concrete samples representing various rock strata using a field-scale drilling machine. The samples with and without interfaces have been tested to replicate various underground roof strata. The signals returned from the drill machine, as the drill bit passes through the layers, have been analysed and interpreted to characterise whether the drill response data can differentiate various strengths associated with the rock layers. The initial laboratory results are promising as they show distinct responses of the various sample blocks in a controlled environment. The drilling data can differentiate the synthesized rock samples and detect ‘signatures’ of the roof strength variability and delineation of lithological interfaces (transitions). The weight and torque on the bit vary and show dependency on the strength of the blocks.

Nov 29, 2022

I should like to congratulate Dr. Salamy on his most informative paper.Under the heading of "future development" Dr. Salamy states the intention of using 3 in. lifters. In this connection I should like to mention one or two of our findings at the Croesus Plant of North Kalgurli (1912) Limited. We have converted a 5i ft. x 11 ft. grate discharge ball mill to a high level overflow rod mill. When we were considering this conversion we explored the literature and decided on using 2t in. lifters on alternate liners-the results were not encouraging. The mill all but "took off" from its foundations,and performance with regard to tonnage was poor. There...

Jan 1, 1956

Base metal skarns have provided most of South KoreaÆs Pb-Zn production since the end of the Korean War, with the bulk of production coming from the Yeonwha group of mines. Currently only the Kumho Zn-Pb mine remains in production, while magnetite skarns are mined as iron ore at the old Yomisan and Ulsan base metal deposits. Base metal skarns within Korea fall into two groups; those hosted in Cambro-Ordovician limestone sequences, situated mainly in sub-basins in the northeast of the peninsula and those hosted within carbonate volcaniclastics of the Cretaceous Gyeongsang Basin, in the southeast. Sulphide mineralisation is dominated by sphalerite, lesser galena, arsenopyrite and pyrrhotite, with subordinate chalcopyrite and molybdenite with Ag-Co credits. Skarns are composed of pyroxene-clinopyroxene-garnet-carbonate-quartz and magnetite, grading into silica-chlorite hornfels. Most of the significant deposits display both pipe-like and stratabound morphology. In the Hwanggang district, a zoned distribution of Ordovician carbonate hosted, polymetallic Mo-W and Zn-Pb-Cu-Ag base metal deposits is observed around the margin of a Cretaceous granite intrusion. Similar polymetallic zoning is recognised in the Sangdong district, where deposits include Sangdong (W), Abisan (Au-As) and Yomisan Northwest (Zn-Mo) and Yomisan Southeast (Zn-Cu-Co), hosted in Ordovician carbonates in proximity to Cretaceous quartz porphyry intrusives. The Taebaeksan district hosts the largest deposits at the Yeonwha group of mines. Although production ceased in 1993, significant resources remain, hosted in Ordovician limestone and dolomite that have been intruded by Cretaceous quartz porphyry dykes. Deposits in the Cretaceous Gyeongsang Basin consist of bedding concordant, vertically stacked base metal skarn mineralisation at several stratigraphic horizons, connected by carbonate-base metal veins with a pipe-like geometry. Evidence such as massive sulphide layers and restricted proximal carbonates suggest mineralisation was initially partly syn-depositional, with both base metals and carbonate venting onto a lake floor, being reconstituted to skarns by later magmatic activity. Skarn mineralisation is universally closely associated with the Cretaceous Bulgugsa Series acid intrusive activity. A common intrusive-structural relationship is recognised at some deposits, with bedding plane and imbricate thrust faulting, introducing felsic intrusives as sills. These intrusions probably introduced the base metals, carbonate, boron, heat and silica, which metasomatically reconstituted the carbonate lithologies to form skarn assemblages. The Korean base metal skarn deposits are regarded as Zn-Pb chimney-manto skarns and display similarities to the Mexican manto type deposits.

Jan 1, 1999

By T Napier-Munn, E Louwrens, L Keeney

Geometallurgical characterisation of ore deposits is accepted practice in some parts of the mining industry today. Its primary aim is to provide constrained inputs that reflect inherent geological variability and its impact on metallurgical performance for the deposit. Geometallurgy improves project value because it suggests more valuable alternatives for scheduling and processing through an increased knowledge and understanding of the interactions of rock properties and extractive technologies. Lower project cost (both capital and processing) and improved recoveries are the result from closer tailoring of the mining and mineral processing strategies to the characteristics of the resource (Dunham, Vann and Coward, 2011). Tailings storage facilities (TSFs) can be seen as potential resources and it is argued that fundamental geometallurgical characterisation as applied in ore deposit characterisation should also be applied to planning the retreatment of TSFs. This paper will describe a research project at Julius Kruttschnitt Mineral Resource Centre assessing if geometallurgical principles and methodologies can successfully be applied to TSFs as they have been to primary deposits. The project is establishing a new standard method of tailings evaluation which will include a 3D spatial model of the tailings resource. Initial domaining of the TSFs was done using principal component analysis followed by k-means cluster analysis based on chemical assays from drill core samples. The subsequent characterisation of the drill core samples has involved chemical, mineralogical and metallurgical profiling, with a range of metallurgical tests being conducted on the samples. This characterisation step is followed by class-based analysis, predictive modelling and process performance domaining with the ultimate objective of establishing a 3D spatial model incorporating geochemical, mineralogical and metallurgical performance data. This approach, which takes into account processing performance permits a more realistic (as compared to doing limited chemical assays and metallurgical testing) economic evaluation of the potential of reprocessing the tailings material. It is believed that the approach is generic and can be applied to other TSFs being considered for reprocessing. The present case study has also established the gold, copper, magnetite and cobalt deportment for an iron oxide copper-gold deposit tailings resource.CITATION:Louwrens, E, Napier-Munn, T and Keeney, L, 2015. Geometallurgical characterisation of a tailings storage facility – a novel approach, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 125–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By V A. Maltsev, V I. Panin

The question of prediction and prevention of dynamic events û rock bursts (RB), tectonic rock burst (TRB) and mining-induced earthquakes (MIE), induced by large-scale mining, are discussed. The mine itself and the host geological environment are taken as a natural-technical system (NTS) whose evolution is characterised by alteration of the adaptation-bifurcation (catastrophes) periods. So, to predict TRB-MIE means to predict the limiting NTS states that are determined from the NTS geological monitoring data, and to prevent the said events means to control the processes of rock deformation and failure within the critical zone. The study considers particular examples of how TRB-MIE-events are predicted and prevented in apatite mines, Kola peninsula, Russia.

Jan 1, 2000

Operation of a pilot heavy medium separation plant allows flexibility of operation not normally possible in an operating plant. Much useful data can be obtained, although some limitations apply. Projects carried out at AMDEL have included HMC separations at 1.5 to 3.6 specific gravity, comparative operation of HMC and DWP separators and the use of fine feed and product screens. Investigations of this type have provided a considerable amount of information on HMS plant performance and characteristics under a wide range of operating conditions.

Jan 1, 1987

By B Godel, E R. Ramanaidou, M Verrall

Fortescue Metals Group Ltd Iron Bridge (IB) operation is a magnetite deposit located in the Pilbara region of Western Australia situated around 145 km south of Port Hedland. This Mesoarchean deposit belongs to the 3230 Ma Pincunah banded-iron formations (BIF), a member of the Kangaroo Caves Formation, Sulfur Springs Group (van Kranendonk, 2000).

Sep 18, 2023

By F Clark, B Catto

The Mako domain comprises the Mako lodes at Sunrise Dam Gold Mine, Western Australia. This domain was initially bulk or æbucketÆ domained for the open pit resource in 2000, due to complexity in defining the lodes as a result of low drill density. Negative ore tonnage and positive grade and ounce reconciliations were experienced during mining of the domain in the mega-pit, though only small volumes of the domain were mined. Significant amounts of exploration and underground grade control drilling has been completed since the initial bulk domain interpretation and greater geological understanding of the mineralisation controls and geology of the lodes now exists. Mako provides approximately 50 per cent of the ore tonnes and ounces for the North Wall Cut-back, the latest open pit phase of mining at Sunrise Dam. The importance of Mako to mill supply and life-of-mine planning, as well as past reconciliation performance necessitated a reinterpretation of the domain to increase confidence for mining. Historic exploration drilling, underground grade control drilling and detailed pit-wall mapping were used to build mineralised subdomains within the confines of the original domain. These reflect more closely the spatial extents and geological controls on the mineralisation. A new resource model using the multiple indicator kriging (MIK) technique was generated using the new domains. It resulted in a decrease in tonnes and ounces but increase in grade for the sum total of the new domains compared to the old æbucketÆ domain. This is attributed to the increased selectivity and structural constraints imposed by the new domains. A retrospective comparison of the Mako grade control from the mega-pit versus the new resource model was conducted, which æreconciledÆ 103 per cent tonnes, 106 per cent grade and 110 per cent ounces. This has provided confidence that the new model is a better estimate of the lodes. Qualitatively, the new model is a better representation of the geology and extent of the mineralised structures with significant areas of change identifiable. Grade-tonnage plots comparing the 2006 and 2008 models show that most tonnes have been shed from the low-grade û subeconomic grade cut-offs. This is mostly attributable to the volume reduction of æoreÆ in the 2008 model compared to the 2006 model, where the true mineralised zones are captured by the new domains. The reinterpretation and remodelling of Mako is an example of an evolved domain model and shows that mineralised zones need to be differentiated adhering to the geology and geological controls on mineralisation, which are understood largely due to increased drilling density coupled with mapping.

Jan 1, 2009

Late Cretaceous and early Tertiary coals in the Greymouth, Ohai and Kaitangata coalfields represent a major national energy resource comprising-up to 2500 x 106 tonnes of coal in ground. The three coalfields are closely related in terms of age and sedimentary and structural character. The most striking feature common to all is the complexity of the geology which has severely restricted exploration and mining of these coal resources. This complexity is manifest in the irregular lensoid nature of coal seams and by the incidence of unpredictable medium and small scale faulting and folding. There are many geological similarities between these coalfields which are considered to arise from a common origin which can be related to the plate tectonic evolution of the southwest Pacific region. In order to efficiently assess and exploit these coal resources it will be necessary to know their geology in great detail. This can he achieved by increasing the understanding of the sedimentary and structural evolution of the coal bearing basins. This knowledge may be gained by the application of traditional (ie drilling, field mapping) and innovative techniques (ie high resolution seismic, in seam seismic) with on going research-oriented studies (ie basin analysis, coal petrography).

Jan 1, 1987