Search Documents

By Peck RC

The ore body at Elura contains fine grained galena and sphalerite in a matrix which is mostly pyrite. A differential flotation circuit concentrates lead and silver in the first section and zinc in the second. The lead section, shown in figure 1, was sampled in detail previously and the metallurgical performance assessed on a size by size basis. That assessment took no account of liberation and given the fine grained nature of the ore body, this could lead to an incomplete picture of the flotation performance. Liberation measurements were made using the QEM*SEM system on four size fractions of samples taken from seven different streams in the lead section. Using the mineral flows obtained from the mass balance around the lead section an excellent liberation balance was obtained which enabled the effect of liberation on the flotation performance to be assessed. The measurements indicated that only 17 per cent of the galena and 28 per cent of the sphalerite in the flotation feed was liberated. On the other hand 31 per cent of the gangue iron sulphides were liberated. The final concentrate was largely composed of locked galena and locked iron sulphides with 85 per cent of the product being locked. There was a small but significant fraction of liberated pyrite.

Jan 1, 1991

By T QUINLAN

A resource estimate uses data obtained by sampling an orebody. An example is described in which a random drilling pattern did not provide a representative set of assays, and the estimated resource was significantly less than the mine production. It is believed that a better estimate would have been made if the exploration holes had been drilled on a regular grid.

Jan 1, 1992

The geotechnical factors controlling the design of the open pit slopes of the Pasminco Century Mine near Lawn Hill, Queensland are presented below. Pasminco Century is a stratiform shale hosted zinc deposit in the Lawn Hill Formation that is overlain in part by the Thorntonia Limestone Formation. Both the mineralisation and overburden is located within a competent rock mass such that intact rock strength and discontinuity spacing is generally sufficient to prevent large-scale slope failure by breakage through the rock mass. Rather, overall slope stability issues are dominated by the major discontinuities within the rock mass. The deposit is located in a structurally complex regime, it consists of a synclinal basin which is truncated by easterly striking normal faults through its centre and northern and southern limits and by an unconformity on its eastern and western margins. Deposit geometry and slope stability is further complicated by small-scale folding, a pattern of northeast and southeast striking subvertical faults and north easterly dipping thrust faults with their associated fault emplaced blocks of Lawn Hill Formation in the overburden. The large size of the deposit requires a staged mining approach with the excavation of both final pit walls around the external sides of each stage and interim pit walls along the internal boundaries between adjacent stages. The deposit geometry and major discontinuities control not only the final pit wall design but also interim wall location and orientation, excavation sequence and in some stages the excavation schedule. Two and three-dimensional limit equilibrium stability analyses were conducted using both deterministic and probabilistic approaches to determine appropriate pit wall design criteria and to select a suitable excavation sequence and schedule.

Jan 1, 2000

By J E. Everett

When ore is being selected from a regularised block model, a common procedure is to accept as ore any block whose iron content exceeds a cut-off value, and whose content in each contaminant analyte is below an appropriate cut-off value. This method defines a quadrant within the multidimensional analyte space, such that any block lying within the quadrant is accepted as ore and any block lying outside the quadrant is rejected as waste. The cut-off levels can be adjusted to maximise ore tonnage at a target grade (or analyte vector). When the method is applied to a project comprising multiple pits with systematically differing grades, it is found that ore tonnage at target grade is maximised if different cut-off quadrants are used for the different pits. This is apparently illogical, because it implies that an ore block from one pit may be accepted as ore, but an identical block from another pit is rejected as waste, even when ore from both pits is to be blended into the same product and there are no production cost differences between the pits. The paradox is an example of the ætheory of the second bestÆ: if there are multiple conditions for optimality and one condition is broken, then obeying the other conditions may not be the best policy. The problem lies with the quadrant cut-off method, which is shown to be inconsistent even for selecting ore from a single pit. A criterion that is inconsistent cannot be optimal. It is shown that a linear composite cut-off function provides maximum ore tonnage, and that a single composite cut-off criterion is consistent and optimal over multiple pits. Further, it is shown that a composite cut-off function not only maximises ore tonnage at a specified composition, but also can be used to select ore so as to maximise project value, if marginal costs and values are available.CITATION:Everett, J E, 2013. Selection of ore from multiple pits, in Proceedings Iron Ore 2013 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By F Jiao, J Wang

By the year 2000, China was the sixth largest gold producer in the world, with about one-quarter of total production being derived from refractory or semi-refractory deposits. Although bacterial oxidation plants had been previously tried in China using local technology, these plants had not been commercially successful. The Laizhou Gold Enterprise (Tarzan BioGold Co Ltd) located in Shandong Province, undertook to modernise their gold processing facility in 2000 with the introduction of Bacterial Oxidation (BACOX) Technology. In 1997 BacTech Australia and Mintek of South Africa had formed a technology partnership, combining forces in the provision of bioleach technology. Under a cooperation agreement, BacTech/Mintek were chosen as the preferred technology providers for this first application of commercially proven bacterial oxidation technology within China. The paper describes the successful operation of this plant over the last three years. The events of project implementation are described, from the metallurgical testing of concentrate; through to the commissioning at the design throughput of 100 tonnes per day resulting in 80 000 ounces (2.5 tonnes) per year of refined gold. Process aspects of the operation encountered over the last three years are discussed which illustrate the robustness of the operation. The success of the bioleach facility has led to an advancement of plans to double plant capacity and some of the innovations, which may be employed in this expansion phase, are discussed.

Jan 1, 2004

By M DellÆAmico, K Vining

The iron blast furnace is the most widely used and efficient producer of liquid iron; however, emissions from sintering and coking cause environmental pressure for the integrated steel works. The combustion of coke fines (breeze) during sintering contributes to greenhouse gases (GHG) (eg carbon dioxide) and is a source of SOx and NOx emissions. Coking capacity is also constrained by environmental concerns and economic factors, such as increased coke consumption, and short supply is leading to high prices. Improved coking practices, which result in reduced production of fines, are also contributing to the tight availability of breeze for sintering. This combination of factors presents an opportunity to consider alternatives to coke as a fuel for sintering. CSIRO Minerals has been investigating the use of wood biomass/char as a substitute for coke during sintering. Wood biomass, or char produced from it, is an attractive carbon source as carbon dioxide liberated during combustion can be sequestered back into growing biomass. It has great potential to reduce the emissions from integrated steelworks and improve their environmental acceptability. Harvested biomass/char is also a renewable and sustainable resource and can be integrated with good land management practices such as remediation of salinity affected land. Weeds, especially woody weeds, can also be used as a source of biomass for charcoal, and integrating char production with weed management can help address a pressing environmental issue in Australia. Previous reported preliminary testwork indicated that the use of Red Gum char as a replacement for coke resulted in a product sinter of comparable quality, improvements in productivity and significant reductions in SOx and NOx emissions. In the latest testwork, CSIRO has examined the properties of a range of potential charcoals, and has conducted a further series of granulation and small-scale sintering trials with them in simulated Japanese Steel Mill iron ore blends. Sinter fuels characterised and evaluated include industry sourced coke breeze, commercially available wood char and a charcoal from prickly acacia (acacia nilotica). Prickly acacia has been declared a noxious weed, is widespread in Australia, and is classified as a æWeed of National SignificanceÆ. The results presented in this paper support the notion that charcoal outperforms coke in many aspects of iron ore sintering and factoring in environmental considerations makes the switch to charcoal even more favourable.

Jan 1, 2005

Mr GEPP said: "He proposed at the outset to draw attention to figures dealing with the population of the countries adjacent to Australia for the purpose of comparison with the population of the Commonwealth. He would deal more particularly with the areas of land surrounding the Pacific and Indian Oceans. Korea and Japan had a population of 18,000,000 ; China, 437,000,000 ; Persia, 9,000,000 ; Arabia, 5,000,000; South Africa, 129,000,000; Madagascar, 3,500,000 ; India, 251,000,000; Siam, Indo-China, and so forth, 16,225,000; Federated Malay States, 3,225,000; and, very significantly, Java, only four and three quarter days from Fremantle, over 50,000,000. From the map displayed an idea of the comparative areas of the countries mentioned and Australia could be gained. It was rather amazing that Australia, with its great potentialities, had only about 5,150,000 people. New Guinea had over 750,000 people; Hawaii, a mere speck, 250,000; New Zealand, 1,300,000; North America, 130,000,000; Central America, over 15,500,000; and South America, over 65,000,000. Colombo was only six days from Fremantle, and it was only nine days from Capetown to Albany, and eight days from Albany to Hobart. Proceeding, Mr. Gepp said "It was in 1911 and 1912 that I had the good fortune to spend nearly twelve months in Europe, and during the course of my work in England and Germany to have the oppprtunity of studying both the economical and political systems in some detail... I was in Berlin at the time of the visit of Lord Haldane, when an effort was made by the British Government to arrive at some under...

Jan 1, 1923

By O Aydan, K Sugiura, A Sakamoto

It is well known that some sinkholes or subsidence take place from time to time in the areas where abandoned room and pillar type mines exist. The authors have been involved with the stability of abandoned mines beneath urbanized residential areas in Tokai region and there is a great concern about the stability of these abandoned mines during large earthquakes as well as in long term. The 2003 Miyagi Hokubu and 2011 Great East Japan earthquakes caused great damage to abandoned mines and resulted in many collapses. Particularly the effect of the quality of backfilling of abandoned mine below the urbanized areas is very important under static and dynamic conditions. The authors present the effect of the quality of backfilling on the ground subsidence associated with abandoned lignite mines under static and dynamic conditions and discuss its implications on the urbanized areas above abandoned lignite mines in this study. CITATION:Aydan, O, Sugiura, K and Sakamoto, A, 2018. The quality of backfilling of abandoned lignite mines on ground settlement under static and dynamic conditions, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 134–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Longwall mining has historically been considered an application for only deep reserves. This has changed in the recent past as longwall has become competitive with surface mining. Many resources marked for stripping now he in the domain of longwall. Today, the best longwall mines compete with strip mines operating in even the lowest stripping ratios. Longwall mining has become more widely applicable than it ever has been in the past and it is now generally considered the method of choice in situations where high levels of coal production are required. But the best way to use longwall mining has become less certain with the opportunities that highwall access provides. Wall-to-wall mining is the use of retreating longwall developed from and retreating toward a highwall. As a surface mine reaches its ultimate highwall, the opportunity for longwall punch mining or wall-to-wall mining is obvious. There are several clear operating advantages to operating a longwall in this way and where highwalls are available, the best economic decision will generally favor planning a direct approach. Yet wall-to-wall is not applicable in every situation even when highwalls are available. Moreover, the advantages of wall-to-wall mining do not always justify the cost of trenching or box cuts to access coal . However, many tactical advantages of operating from the highwall can be realized with the use of specially equipped blind drilled or raised bored shafts. This paper discusses novel techniques for a shaft assisted mining system which permits the addition of conveyor structure and mine systems from the surface to the face for advance and retreat mining with longwall, shortwall or room and pillar panels.

Jan 1, 1998

By B Maybee

In underground mine planning, many potentially value-eroding decisions are made due to a lack of time and proper evaluation practices. The information required for mine planning decisions goes beyond external sources of uncertainty that are recognised by typical evaluation techniques used in the mining industry, to include technical factors (eg mine development layout) and the ability of a mineral extraction project to achieve its anticipated production levels. Due to the individual characteristics that define underground mining projects, each will exhibit a different risk profile, and thus advanced optimisation and evaluation techniques are required to capture this information.As underground mine planning tools become more sophisticated, mine planners have the capacity to investigate numerous mine sequencing options to identify the best strategy for a given project, creating higher value for shareholders. This paper describes a risk-based evaluation methodology (RbEM) that accounts for financial and technical risk in the evaluation of underground mining projects. While the use of the RbEM has been described in previous works, no benchmarking of the benefits that can be realised from a change in those decisions that are made early in the process has been undertaken. To show the benefits that can be achieved from using the RbEM, this paper updates a case study to which the RbEM was applied, and takes a retrospective look at whether additional value would have been gained by following the strategic recommendation of the RbEM versus a typical optimisation exercise that aims to maximise the net present value.CITATION:Maybee, B, 2012. Can a risk-based evaluation provide a more valuable mine design?, in Proceedings Project Evaluation 2012 , pp 53-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

Low-grade, porphyry copper type mineralization at the Moonmera prospect is related to the intrusion of a granodiorite porphyry mass into the Upper Permian "Gracemere granodiorite". Significant copper mineraliza- tion appears to be associated with the alteration assemblage quartz-sericite- kaolinite. The ore shell is surrounded by a zone where montmorillonite and kaolinite are in greater abundance and this assemblage is over- lapped, mainly at depth, by potassium feldspar alteration. Secondary biotite is abundant throughout the mineralized zone. Preliminary sulphur isotope results on the sulphide mineralization are compatible with a magmatic origin for the sulphur.

Jan 1, 1974

By J Green, R Bartlett, A Goldstone, D Ferguson

Solid Energy New Zealand is developing an extension of its Rotowaro open cast coal mine near Huntly. This large 8 year, 11 million tonne opencast coal mine, referred to as the Awaroa Project, is fundamental to Solid Energy's medium term business strategy and meets its open pit coal resource needs while further resources are developed for the long term. Equally importantly the project is also fundamental to meeting New Zealand's energy requirements in the face of growing demands, a dwindling gas resource, and dry winters creating hydropower shortages. This project with its national significance in the current energy climate, its significance to Solid Energy as a business and its significant size has been consented against a backdrop of criticism of the Resource Management Act and the introduction of the 2003 amendment to the Act. As is common practice for this type of project Solid Energy conducted a significant technical programme in order to complete a comprehensive assessment of environmental effects. Solid Energy also has an active programme of community and interested party consultation and this programme formed the basis for project based consultation with local residents, regulatory bodies and iwi. As a result of the approach taken the environmental effects of the project were shown to be no more than minor and Environment Waikato considered that the project should be processed under the limited notification provisions of the RMA amendment. The project was processed under RMA quickly and efficiently and consents were granted within 6 months of lodgement. The RMA and its 2003 amendment provided a good framework for dealing with this project and did not impede the process of development of this important energy resource.

Jan 1, 2004

By R A. Pax

Operational grinding mills emit significant acoustic emissions which are a consequence of the dynamic environment prevailing inside them. From a technical perspective, the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of primary comminution tumbling mills. To enable a logically coherent picture to be formed of the processes inside a mill, arrays of microphones have been used. This approach allows a clearer picture of the in-mill behaviour of the charge to be accessed. In contrast to single microphone approaches, usually located near the expected charge toe position, an array of microphones allows much more useful information to be obtained from grinding mill noise.This paper will discuss and present data obtained from microphone arrays positioned at the toe and shoulder locations of a mill, and how this information can then be used for the optimisation of grinding mills in real-time.CITATION:Pax, R A, 2012. Determining mill operational efficiencies using non-contact acoustic emissions from microphone arrays, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 119-126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Wright S

The feed to the Cockle Creek Imperial Smelting Furnace consists of mixed Pb/Zn con- centrates and lead sulphate-containing elec- trolytic zinc plant residues. Roasting was investigated as a means of desulphurizing the feed to less than 1%. Laboratory studies showed that two process streams were required in which concentrates containing 20% Pb were roasted separately from the leach residues. The residues along with fume from the roast- ing and a portion of concentrate were desul- phurized by means of the roast reduction reaction. Conditions were defined to give

Jan 1, 1986

By J O. Watson, V S. Vutukuri

This paper presents results of an investigation on acoustic emission characteristics of granite, sandstone and rock-like material in the unconfined compression and tensile tests. Both the acoustic emission signature and stress-stain curve are analysed in the experiments.The experimental results show that different acoustic emission characteristics are observed at different stress and deformation stages in unconfined compression and tensile testing. Extensive and unstable acoustic emission changes may be interpreted as indicating failure of the rock.

Jan 1, 1999

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

By AJ LYNCH

Broken Hill metallurgists have been responsible for some of the most important developments in mineral processing technology. These occurred mainly in two periods, 1902 - 15 and 1955 - 70. Mineral flotation was developed as an industrial process during the first period and this happened in two stages, the recovery of zinc minerals from the tailings dump accumulated during the gravity concentration of the oxidised ores and the selective recovery of galena and marmatite during flotation of the primary ores. During the second period fast accurate analytical procedures were developed to provide rapid assessment of process performance, and new means of controlling the process were devised which improved throughputs, grades and recoveries. These technological successes were due to the skills of the metallurgists and the commitment of the companies. They brought large financial returns. They were achieved under difficult circumstance. There are important lessons to be learnt from these successes.

Jan 1, 1992

By C Torrisi, J Andreatidis, M Duffy

BHPÆs Cannington process plant was commissioned in October 1997. The Cannington ore contains high grades of silver, lead and zinc but also contains high levels of fluorine which must be removed to produce a marketable concentrate. As a consequence the plant is more complex than the typical base metal concentrator. Some of the features of the Cannington operation include a single stage autogenous mill, multiple stages of flotation cleaning, two leach circuits, pressure filtration and a paste fill plant. The start-up and achievement of design performance for new lead/zinc operations has traditionally taken much longer than for gold or copper operation and is littered with many tales of woe with feasibility targets often not achieved (Agarwal, Brown and Katrak, 1984; Bulatovic and Wyslouzil, 1999; Leung, Andreatidis, Woodall and Alford, 1996; Sherman, 1999; Ward, 1998).

Jan 1, 2000

By Wetzeil N

High ambient temperatures combined with high surface humidity in the north of Australia and, in particular, the northern areas of the Northern Territory can make underground workplaces relatively inhospitable at certain times of the year. . Woodcutters' silver/lead/zinc mine, situated some 80 km south of Darwin, would be the most northerly underground operation of any significance in Australia. As such, during the build up to the wet season, it has a particular problem of ventilating a deep underground mine with already high dry and wet bulb temperatures at the surface. The Mine Management Act and Regulations mention only that workplaces shall be 'in a fit state for a person to work in or occupy'. Woodcutters therefore set in progress a Heat Stress Program to endeavour to set standards which would be more measurable and justifiable. The aim of the program was to compile a record of ambient atmospheric conditions in the working areas such that areas and/or work activities generating high ambient temperatures and humidities could be identified, quantified and qualified. Once the analysis stage of this program was completed, Woodcutters compiled a set of recommendations for the continued monitoring for, and control of, heat stress conditions to ensure that no underground employee was placed at risk from 'heat stress'. These recommendations are discussed in this paper.

Jan 1, 1994

By S D. Dessureault

In large coal strip mines, there are many different processes at work: stripping, overburden removal using trucks/shovels, cast blasting, slot dozer pushing, more fragmentation and further truck/shovel benches. A key component to each of these steps is the use of machines. In modern operations, most machine costs are tracked within Enterprise systems that transact costs and repair work order management. Similarly, in contemporary mines most machines are tracked using technology that provides precise performance measures for each key process. Such technologies include productivity monitors on draglines, dozers and drills and fleet management systems for trucks and shovels. Linking these two sources of seemingly disparate data û costs and performance by machine û would allow for the precise calculation of unit costs by specific machine. This is similar to an activity-based costing system, except in this machine-based system, calculations are made at an even finer granular level. There are many uses for such an integrated information system in mine planning and performance management, both in real-time and through historical analysis.A real-time fleet costs (FLC) measurement process was developed as part of a larger blending-related, multi-million dollar project centred on a centralised remote control room developed at the University of ArizonaÆs Mining Information Systems and Operations Management Mine Control Center. The FLC component of the overall blending system would allow a mine controller to manage the equipment fleet by viewing its cost in real time and, when mixed with other revenue-related components, the exact profit. For example, a mine controller may show high utilisation while still maintaining a production surplus. This could occur, for example, if the equipment is driven long distances. This might appear in traditional performance metrics as æhigh production performanceÆ, but in reality may prove less profitable. This paper discusses the technical development of the FLC, its deployment and its impact on controller performance, and compares mine profitability before and after its application.

Sep 26, 2011