Search Documents

One of primary causes of poor blast performance is the improper relief of explosive energy. Under or over-confined blasts modify the explosiveÆs path of least resistance, which changes where and when the explosive energy is applied resulting in less than optimum blast performance. During the research for this paper the overbreak characteristics of five full-scale blasts were quantified using high speed cinematography and borehole cameras. The effectiveness of various overbreak control methods was also evaluated to guide design refinement. The results of this research along with general recommendations for reducing excessive damage are included with this paper.

Jan 1, 1999

By K S. Smith, B P. Jackson, P J. Lamothe

The upper Arkansas River south of Leadville, Colorado, USA, contains deposits of fluvial tailings from historical mining operations in the Leadville area. These deposits are possible non-point sources of acid and metal contamination to surface- and ground-water systems. We used stable-metal isotopes to help ascertain metal retention and release mechanisms that influence metal transport from the deposits to shallow ground-water systems. To accomplish this, we excavated an intact core from a small fluvial tailings deposit and performed laboratory column experiments to examine the amount of metals leaching through the core. Deionised water was continuously applied to the top of the core, and effluent was collected from the bottom of the core for a period of about two months. Three saturation conditions were used, including unsaturated, partially saturated, and fully saturated. Reducing conditions developed upon partial and complete saturation of the core. During the unsaturated leaching phase, core effluents were acidic (pH 2.8 - 3.5) and contained elevated metal concentrations. During a portion of the unsaturated leaching phase, stable-metal isotope spikes and conservative tracers were simultaneously applied to the top of the core. The isotopes provide a means to delineate metal behaviour within the core. During the unsaturated leaching phase, the isotope spikes did not exhibit breakthrough with simultaneously added conservative tracers. However, some of the stable-metal isotope spikes did break through when reducing conditions occurred in the core (during the partial- and completesaturation conditions). In this paper, we use Cd as an example of the utility of stable-metal isotopes in geochemical studies. In the case of Cd, after the core was partially saturated, the 111Cd spike was released as evidenced by a change in the Cd isotope ratios in the effluent. This release continued during the fully saturated leaching phase, however, the total Cd concentration did not increase. These results suggest that the 111Cd spike was retained inside the core during the unsaturated leaching phase, and only partially released as reducing conditions developed. Results from this core-leaching experiment indicate there is a large reservoir of water-soluble material within the fluvial tailings deposit, which yields elevated metal concentrations and high acidity, and which may degrade adjacent ground- and surface-water quality. Use of stable metal isotopes in this study facilitated the determination of different metal-retention processes, metal-release processes, and metal sources in the fluvial tailings deposit in response to changing geochemical conditions.

Jan 1, 2003

Production of refined zinc (99.95 per cent) at the minesite without increasing greenhouse gas emissions is considered. As an example, exploitation of the full reserve of the McArthur River orebody is proposed, using the existing concentrator, whilst introducing radically innovative smelting technology. Bulk flotation of all the sulphide minerals is followed by smelting in a melt circulation reactor with tonnage oxygen. By smelting the high-energy pyritic concentrate and reacting the evolved sulphur dioxide with near-mine dolomite, a large amount of electricity can be generated. This is enough to supply all the requirements for the smelter itself, an air separation plant and a facility for compressing and liquefying carbon dioxide. Carbon dioxide is disposed of off-shore for enhanced oil recovery or by other means. The reacted dolomite fixes sulphur as an inert and environmentally acceptable solid residue. Treatment by these means leads to virtually zero gas emission smelting. The paper concludes with a vision for the future in which expansion of zinc smelting capacity is seen to be definitely needed.

Jan 1, 1998

The paper is aimed at mining engineers and other mining practitioners in the metalliferous mining industry who are considering the use of roadheaders and wish to understand the basic geomechanical and operational principles controlling their performance. The paper aims to address metalliferous minersÆ general unfamiliarity with roadheader technology, which is one of the factors which has limited the application of these machines in such mines. The historical development of drag tool mechanical excavation machines is briefly discussed, and factors affecting the application of roadheaders are mentioned. The mechanics of cutting with drag tools is then reviewed as are the effects of these and tool wear on tool performance. The implications of tool performance to roadheader performance are mentioned, the potential benefits of high pressure waterjet assistance are discussed and the relative performances of different tool types and materials are compared. Roadheader performance factors including productivity and utilisation are mentioned, and the state-of-the-art of conventional roadheaders is discussed in the context of machine weight, power and cutting head configuration. The influence of these and rock strength on machine productivity is analysed. Alternative, developing technologies are discussed which may extend the effective use of mechanical excavation into stronger rock masses which are beyond the range of conventional roadheaders. Finally, conclusions on these discussions are presented, along with recommendations for continuing research and development.

Jan 1, 1997

Rock bolting has become the most important method of ground support at Mount Isa. Various types of rock bolts are used to suit the different applications and requirements. To apply rock bolting techniques satisfactorily, it is necessary to have some knowledge of the nature of the rock, the type of rock failure, any stress redistribution which may occur during the intended life of the rock bolt and the time for which ground support is required. At Mount Isa there are a number of dif- ferent applications of rock bolts for ground support, and some trends in rock bolting techniques.

Jan 1, 1971

By Jackson S

An investigation into different aspects of importance in the understanding of explosibility of hybrid mixtures of coal dust, air and gases potentially found within mine workings through a comprehensive laboratory program of explosibility tests was conducted. Plotting of test results revealed that conditions of potential explosibility could be described using two dimensional flammability limit surfaces- for coal dust/oxygen; methane/oxygen; and coal dust/methane mixtures. From these plots, the three dimensional flammability envelopes defining the explosibility of the coal dust/methane/oxygen mixtures can be defined and illustrated for a coal sample. The surfaces of the three dimensional envelope describe limits which separate inert mixtures of coal dust and methane at varying oxygen levels from those concentrations which are ignitable under defined conditions. It is considered appropriate to generalise that the geometric shapes of these limit regions are applicable to all type classifications of coal dust. There are practical applications of these results to the underground environment.The action of free radical initiators in the propagation of a methane gas explosion was examined for its applicability to the flammability of coal dust/gas/air mixtures. The oxides of nitrogen or NO x radicals have influence upon the lean limits of flammability of hybrid mixtures and this is illustrated by use of three dimensional coordinate geometry. Gases can be introduced to the underground environment through the exhaust gases of diesel equipment. It is concluded that radical species can substantially increase the flammability of gas and dust flames and as a consequence raise risk of mine atmosphere explosibility.

Jan 1, 1998

By Sorentino C

Mineral valuation may appear to be a special field of financial valuation when in fact it is a subset of general investment decision theory. The only significant difference in mineral valuation is that in the case of valuing an on-going mineral asset, ie a mine, often there is no initial capital outlay involved. One is required to determine what the mineral asset as it stands is worth. But this is the same problem as determining the maximum one could pay today and not incur a loss over the life of the asset. In other words one needs to determine the Net Present Value (NPV) of the asset. The two most widely used discounted cash flow methods, NPV and Internal Rate of Return (IRR) came of age with the rapid adoption of the personal computer and spreadsheet programs. The two methods are directly related as the IRR is a special case of NPV. NPV measures the absolute increase in real wealth that can be expected from a certain investment, which makes it particularly suitable for mineral asset valuation, but ignores the efficiency of the investment. In contrast, IRR gives the expected efficiency of the investment but ignores the increase in wealth aspect. IRR has two serious theoretical weaknesses; multiple IRR's and a very rigid assumption about the rate of return of reinvested proceeds, plus if no initial equity expenditure is involved there is no IRR. The choice of the ""hurdle"" rate can also be a problem and in certain circumstances one can obtain different rankings of mutually exclusive projects using IRR and NPV. Although NPV and IRR supposedly measure financial risk, in fact they only address a very narrow area of risk, namely the time value of money given the real discount rate. They side step the issue of what the real discount rate should be and varying degrees of risk. The classical way to establish the real discount rate is to use the weighted average cost of capital.

Jan 1, 1994

The mathematical modelling of rock fragmentation by blasting is one of the most difficult and challenging problems of applied mathematics. Not only is complex mathematics required but there is incomplete understanding of the basic physics and chemistry involved. The possibility of getting the physical basis of a model correct by simple mathematical and experimental procedures is demonstrated for the novel process of fragmenting rock by high-pressure arc discharges. While the importance of obtaining the correct physical basis for a model is emphasised, high-pressure arc induced fragmentation of rock is shown to be a powerful laboratory tool for the study of blasting.

Jan 1, 1990

The implementation of a process information management system (PIMS) is to provide a single online, real-time information system. This system provides a unique and completely open view for everyone, based on the key business drivers. It is structured around the three key concepts: process, maintenance and stocks. It combines numerous applications and provides accessibility to common tools and reports, through a web-based user interface, for every one from the floor operator to the General Manager. This æunique and commonÆ view displays raw, online process information that provides a quick health check of the operation at a glance, highlighting areas that require further investigation. The system is based on a hierarchical system of views, from the overview of the whole plant flow sheet to the more detailed operational shop view. It provides a synthetic view between continuous and batch operations, enabling the tracking of each batch produced. The batch view displays the critical batch components, and a comparison with each component of an ideal batch. This enables detailed analysis of each batch to identify areas of improvement. The information system will consist of an online reconciliation of stocks and flow data. This enables focus on the recovery of each process unit on a regular basis. This paper discusses the design strategy for the Process Information Management System, to ensure a unique and open view on the key business drivers is achieved and implemented successfully.

Jan 1, 2005

By T Lancaster

The Mount Gordon operation, consisting of the Esperanza open cut mine and the unique Mount Gordon Ferric Leach processing plant, is operated by Western Metals Copper Ltd at Mount Gordon, 125 km north east of Mt Isa. The processing plant treats predominantly the secondary copper sulphide minerals, chalcocite and covellite. The gangue consists of massive pyrite and a range of silicified siltstones. The processing plant utilises a conventional single stage SAG/cyclone milling circuit, followed by low-temperature/low-pressure autoclave oxidation to produce copper in solution. The pregnant leach solution is treated via conventional SX/EW technology to produce copper cathode. Currently the plant is operating at a nominal production rate of 48 500 tpa copper. The Mount Gordon Ferric Leach technology is the worlds first integrated pressure leach/SX/EW process to be used to treat copper sulphides on a full plant scale. In the last six months, July to December 2001, the plant has emerged from a two-year postcommissioning phase to achieve steady state operation. This has been characterised by high plant availability and consistent production performance in excess of the name plate capacity of 45 000 tonnes. Production rates will continue to increase over the next 12 months to over 50 000 tpa via a planned process of incremental improvements. The pressure leach circuit has consistently achieved availabilities exceeding 95 per cent over the past 18 months. Notwithstanding this, the leach circuit still has a much greater requirement for planned maintenance than SX/EW. For much of the Mount Gordon processing plantÆs operating life, the leaching process has constrained production. Recent developments arising from detailed mass and energy balance modelling have now significantly improved leach capability, resulting in the plant bottleneck being shifted to electrowinning. In order to balance the capabilities of the two circuits however, the surge capacity between leach and SX/EW was increased substantially. This effectively de-coupled the higher capability but lower availability leach circuit from the lower capability but higher availability SX/EW circuit. As a result, electrowinning utilisation has increased to in excess of 98 per cent, which is reflected in a higher overall plant throughput.

Jan 1, 2002

By Muldoon T

Water sprays on mining machines are generally put there to reduce dust; however, research by the Bureau of Mines and others has shown that considerable airflows may also be generated by these sprays. This recognition of water spray-gen- erated air movement led to the "Spray-Fan" - a continuous miner auxiliary ventilation system which was shown to reduce methane peaks by a factor of 15. Recent successes and failures of the Spray Fan are reviewed. More recently, the same principles were used in the design of the "Shearer- Clearer" for reducing dust at longwall shearer operators. The original design was successful; however, a new design is now available which is more practical to install and does a much better job of holding the dust against the face downwind of the shearer. The latest research objective is to eliminate the negative impact of spray- generated air turbulence on continuous miner dust control. Most coal faces in the USA are ventilated in the exhaust mode using "line curtain", and the forward airflow on the side of the heading opposite the curtain is inevitably weak. Air turbulence generated by sprays which are incorrectly located and/or operated at excessive pressures can cause roll back - in which the dust cloud at the face is forced unwind against the ventilation and spreads over the miner cnerator. The general approach to reducing "roll back." is reviewed and art anti-roll back water spray system is presented.

Jan 1, 1983

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

By S M. Arndt, D Tyler, F Reusch

Although significant advances have been made in understanding the mechanics of pit slopes, numerical modelling hasnÆt significantly impacted on the reliability of the design process. It is well known that legacy modelling approaches donÆt simulate large slopes well. In recent times, the emergence of very large finite element (FE) models with more than ten million degrees of freedom and the ability to simulate a large number of discrete structures, has allowed a step change in the simulation precision for slopes. The model size allows global and local effects to be realistically simulated in one model for the first time and the process can be better integrated into normal open pit slope engineering processes. Some examples of simulation of very large open pits are shown that demonstrate the challenges and some recent advances in modelling large slope behaviour. Significant limitations in the current measurement and observation regimes of open pits have been identified.

Jan 1, 2007

By B R. Bittencourt, D A. B Pasin, D Pi

Three main genetic types of hematite can be recognised at Quadrilßtero Ferrffero (QF): Micaceous or schistose hematite derived by metamorphic/metasomatic process during regional metamorphism, increasing eastward, formed under temperatures ranging from 250¦C to 500¦C in CO2-rich aqueous carbonic, high- to medium-salinity fluids. Hematite in shear and mylonite zones, showing a wide variation of fluid and temperature conditions, between metamorphic and hydrothermal conditions. Deformed quartz-specular hematite veins formed during the late phases. Hydrothermal, compact and isotropic hematite developed during a brittle-ductile regime, forming the cement of the boudinage-kink breccia and jacutinga-type of gold mineralisation, under temperatures ranging from 80¦C to 140¦C in aqueous, low- to medium salinity, oxidant fluids, resulting from the interaction of meteoric and metamorphic/metasomatic fluids. Quartz-carbonate-sulfide veins were formed slightly later, through reducing fluids.

Jan 1, 2005

The south-east Missouri cobalt-copper-lead-zinc district is the worldÆs largest lead producer and a significant producer of by-product zinc, copper, cobalt, silver and cadmium. Current production in the district comes from six or seven mines in the Viburnum Trend. Most ores in the Viburnum Trend are characterised by a small number of minerals with simple compositions. Portions of some orebodies contain ores that exhibit greater variations in mineralogy, and these include shale-hosted lead- copper ores, bornite ores and nickel-arsenic sulfide ores. Ore textures include both replacement and open space filling textures, and the paragenetic sequence for the ores is characterised by repetitive periods of deposition of all of the ore and gangue minerals. Ore microscopy is an effective tool for not only the identification of the minerals and textures shown by the ores, but also to determine the mineralogy and textures responsible for beneficiation problems. An interesting variety of sedimentary and structural ore controls have determined the locations of individual orebodies in the district. Based upon the positions of orebodies with respect to Precambrian ridges and knobs, together with areal patterns of mineral/metal zoning, it is interpreted that the ore fluids came from diverse directions to form the deposits in the district. It is concluded that the Old Lead Belt subdistrict was mineralised by fluids that flowed from the north-east and north-west, the Fredericktown area by fluids from the north-east, the Indian Creek subdistrict by fluids from the north-west and the Viburnum Trend by fluids from the north-west and west.

Jan 1, 2008

By Borshoff J, Von Pechmann E

The uranium mineralization in the White's East area of The Embayment is hosted by Lower Proterozoic schists of the Masson Formation which have undergone polyphase de- formation and upper greenschist metamorphism. Significant mineralization is also present in apatite rocks. The ore zones occur near an unconformity with overlying Middle Proterozoic sandstone and breccia conglomerate. Kink breccias and fracture systems related to post Middle Proterozoic reverse faults are the con- trols for mineralizing fluid migration. Pitchblende is the main uranium mineral and it occurs as fine disseminated grains, fibrous webs, clusters composed of botryoidal aggregates and locally as veins. Two genera- tions of uranium mineralization are present. The first generation (pitchblende I) occurs as fine grained inclusions within chlorite II, and the second (pitchblende II) as hydraulic fracture networks and massive veins intimately associated with sericite-hematite-chlorite III. Two hydrothermal alteration phases have affected both Lower Proterozoic and Middle Proterozoic sequences. The most extensive alteration mineral is chlorite, of which a number of varieties has been identified. Mg-rich chlorites are generally associated with the first phase alteration assemblages and are commonly replaced by hematite, seri- cite and Mg-Fe chlorites in massive pitch- blende zones. Other alteration minerals in- clude tourmaline, apatite, talc, quartz, magnesite, graphite, pyrite and rutile.

Jan 1, 1984

Underground measurements, observations and computed simulations, started a long time ago were concerning the study of : - occurence of typical rockburst, - inducing, stretching of main fractures in the roof of caved longwalls. They made obvious a foundamental phenomenon of inducing of strata fractures involving contact be- tween two layers quite different in their elastic characteristics : coalseam and rocklayer.. The start of primary cracks in maximum abutment zone takes place in the rock near the contact surface. It is opening of crevasses induced by traction stress component resulting of difference of rigidity of both materials and no sliding on in- terface. Occurence and stretching of these crevas- ses are a rheological phenomenon so that the rate of advance and stops of the face influence the distance between the crevasses and the stretching of these ones. The characteristics of these cracks in space and time affect mining conditions. So it is for fractures proximity and expan- sion inducing eventual blocks formation in longwall roofs in front of faces, for depth and delay of road- ways ribsides fracturing, inducing some rockbursts. In longwalls roofs, cracks initiated in front of a face can be either quite close or quite distant each from the other one, according to the depth of crushed coal in front of the face, which af- fects also extension of the cracks.

Jan 1, 1988

By D R. Chalmers

Coal dust explosions have occurred in coal mines across the world. The Mitsui Miike Coal Mine disaster in 1963 was an example of how this hazard was not managed effectively, resulting in the loss of 458 lives and hundreds of people sustaining permanent brain injury from carbon monoxide poisoning. Management of the risks for this hazard have been well documented and have been implemented in modern coal mines. A recent trend in some mines has seen the abolition of barriers on roadways on the basis that the risks are being managed by the current controls. These controls include stone dust application, trickle dusters, dust analysis and dust removal. This paper explores the science behind such controls and questions the need for barrier protection on belt roads.CITATION:Chalmers, D R, 2013. Cybulski revisited - Lessons on dust, in Proceedings The Australian Mine Ventilation Conference , pp 165-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By H Beucher

The uranium grade in roll front deposits is the result of successive processes that can be summarised in two steps. First a sedimentary phase, which gives the deposit support, then an oxidation-reduction phenomenon, which leads to the uranium deposit itself. In order to simulate such a deposit, it is important to mimic these different phases. The final aim of such a study is to localise the uranium itself and to reproduce the internal heterogeneity of the orebody in order to simulate the recovery process. The idea in this paper is not to reproduce a genetic approach but to consider the final image of the deposit. Three approaches are proposed. The first one consists of simulating the facies of the sedimentary deposit. The second approach reproduces the distribution of facies resulting from oxidation phenomenon (reduced or oxidised facies). The third approach consists of simulating the mineralisation at the interface of reduced and oxidised areas using the definition of a new data set determined by the grade values. At the end of each approach, the uranium grade could be simulated facies by facies according to the corresponding distribution characteristics. The plurigaussian method dedicated to random set simulations is well-suited for the facies simulations of deposits resulting from several sedimentary processes whether correlated or not. In this paper, the benefit of this method is demonstrated in an actual case study.

Jan 1, 2006

By Van Weert G

Ferrous chloride solution pyrohydrolysis is a successful IICI regeneration process which is carried out in either a spray roaster or a fluid bed. Pyrohydrolysis is not restricted to ferrous chloride only, every metal chloride can theoretically be hydrolysed. In practice, however, the conditions for ferrous chloride pyrohydrolysis differ from those of many non-ferrous metal chlorides eg zinc, lead and cadmium. Hence, a pyrohydrolyser could function as a ferrous/non-ferrous separator, eg an iron oxide and zinc chloride separator. Most pyrohydrolysers operate on solutions, in which case more than 50 per cent of the process energy is needed for heating and evaporating water. However, this disadvantage would be diminished by feeding a slurry to the reactor. Against this background it was decided to investigate the chloridisation of zinc ferrite which is an iron bearing solid with a non-ferrous impurity, and subject to processing and disposal problems. Synthetic zinc ferrite was chloridised in a tube furnace. The gas atmosphere in the tube furnace resembled that of a fluid bed pyrohydrolyser and consisted of HCI, 1120 and nitrogen. Gas composition, temperature, residence time and sample mass were varied. The experiments showed that complete (99.6 per cent) zinc extraction from synthetic zinc ferrite was possible in a simplified pyrohydrolyser atmosphere at 1100 K in four hours. The zinc ferrite was converted into gaseous zinc chloride, and hematite and magnetite solids. It was also found that zinc removal from the zinc ferrite lattice caused not only rccrystallisation of the zinc ferrite into hematite, but also hematite crystal

Jan 1, 1993