Search Documents

By Thomas L. J

A series of tests on rock stress measurement devices used with the overcoring method indicated that improvements could be made in their construction. A prototype inclusion cell was developed with strain gauge rosettes bonded to a 0.05 mm thickness stainless steel sheet which was formed into a cylinder around two end pieces. The finished diameter was slightly larger than previous cells so that the thinner plate and the reduced annulus of Araldite cement in the installation borehole gave a better response in the laboratory than the other cells tested, especially in simulated bedded rock. It was less affected by inhomogeneity and temperature changes. Its high sensitivity should make it suitable for both absolute stress measurement and field monitoring. A table of comparative readings is given for the new cell and for four other devices used in simulated in-situ rock conditions.

Jan 1, 1992

The basic principles of mineral valuation were recognised and propounded at the beginning of this century and have remained virtually unchanged since then. Valuation is seen as a two part process commencing with a technical examination of the mineral property followed by a manipulation of the results of the technical examination in order to determine the monetary value of the project. A thorough and competent technical examination was seen then and remains now as the essential but not sufficient foundation for reliable valuation. All authors stressed the need to maintain the integrity of the data base and to ensure adequate coverage of all relevant aspects. The monetary valuation process through most of the first half of this century was mainly based on the Hoskold two rate method, derived from the formulae for valuing annuities but modified to provide explicitly for recovery of capital. Though the basic principles of valuation have not changed significantly, the means of implementing the components of the technical examination, the styles of deposits being evaluated and the mechanisms of monetary valuation have changed dramatically. Despite all the technological improvements, however, mineral valuations are still as apt to vary from realised performance as at any time in the past. As well, mineral property valuations are now being extended to cover all assets of potential value, including valuation of exploration tenements with or without identified resources. Valuation of exploration tenements will continue to be one of the most difficult and contentious of valuation tasks.

Jan 1, 1994

By Rao A. B, Rao V. D

Northeast of Brazil is situated in the polygon of drought. It covers some very important states like Bahia,Pernam- buco, Paraiba, Rio Grande do Norte, Cea- ra and Piaui , which have a potential for mineral production. Of them the main contributions that comes from Rio Grande do Nor to , Ceara and Paraiba are the scheelite and im portant quantities of granitic pegmatite mine- rals like tantalite-columbites, micas, beryls, precious stones, lithium minerals etc. On the other hand flourishing mineral economy in gold, tin, emeralds, chromium, lead, apatite is most- ly from Bahia; and potassium, salts, and petro- leum are from Sergipe, Alagoas and Bahia res; pectively. The most interesting aspect coninues to be the nucleus of the drought zone constituted of the Rio Grande do Norte, Paraiba and Ceara sta- tes.The first two authors have worked for twel- ve years in the region and have dedicated atten tion and time to two systems, namely skarns and granitic pegmatites. Their mineralogy,petrogra- phy, geochemistry, origin and economy is being worked upon from time to time to accompany the progress that is being achieved both in the sec tors of geology and economy. Besides, during the field campaigns, evidences have been sought to find the best guide horizons for mineralisa- tion and options for the location of target areas and prospection methods for scheelite, tantalites and other pegmatite minerals.

Jan 1, 1988

Government geoscience may be categorised by objective under three headings: Applied Research for Geoscientific Framework Studies, Resource Inventory, and Technical Advice. In Queensland, the Department of Resource Industries is active in all three categories. Under the program-based management system adopted in 1987, three Programs, namely, Geological Survey, Mineral Resources Development, and Energy Resources Development and Utilisation, have geoscience responsibilities.Prime responsibility for geoscience resides with the Geological Survey Program, which provides a geoscientific framework for mineral and energy exploration and the development of the State. Simply stated, the Program goal is to provide geological information when and where it is required. Geological Survey work also encompasses aspects of resource inventory and technical advice, complementing the work of the other two Programs. This role has a 122 year long tradition, for geoscientists of the Geological Survey have been engaged in investigations designed to facilitate the identification and utilisation of the mineral, water and energy resources of Queensland since 1868.

Jan 1, 1990

This paper presents a method for estimating the strength and stability of model coal pillars with bedding planes (weakness planes) inclination. The strength of coal relative to the angular difference between the principal stress direction and bedding planes is considered. The failure behaviour of model coal pillars containing weakness plane inclination by using servo-control Schenck Machine are shown. Uniaxial and triaxial compressive strength of coal specimens are investigated, and test results indicated that the strength of coal pillars depends on the weakness planes inclination with respect to the principal stress direction. However, it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of the coal specimens is reduced. An empirical method is given for prediction the compressive strength of coal containing weakness planes inclination. The results of this method are compared with the experimental results and Jaeger theory. Finally, three well-known empirical strength criteria were tested against the triaxial test data for coal containing weakness planes inclination.

Jan 1, 1995

Efficient performance of pulp lifters to discharge ground rock is critical to the effective performance of SAG and AG mills. The paper covers developments in the design of pulp lifters and associated grates, of both conventional straight-radial and curved types, and of the inner discharge cone. Issues covered include the discharge performance of both the slurry and rock components of the discharge, reverse flow back into the mill through open grates and backflow down the pulp lifters of material that fails to discharge from the mill. The design experience is interpreted in the light of developments in particle flow modelling of the flow of charge in pulp lifters.

Jan 1, 2004

By Williams RJ

This paper presents an overview of the design and development , application to date and potential of a real-time return gas monitoring system.Initially developed as an ACARP/Industry funded project, whose prime aim was to create a `turn-key', prototype, stand alone, real-time, Return Gas Monitoring System (RGMS) capable of providing quantitative assessments of gassiness levels on a shift by shift basis, enabling unusual gas emission patterns to be readily flagged.

Jan 1, 1998

After a very brief historical survey and overall assessment of traffic requirements, the invitation by the British and French Governments for private groups to make proposals for a "fixed link" is described, and the resulting plethora of proposals is reviewed. The three schemes which gave some promise of being adequately backed by private finance are described as follows:

Jan 1, 1987

The paper outlines the philosophies and the methods applied to resource estimation by North Flinders Mines Limited at The Granites. These are based on recognition of the prime importance of quality data, accurate geological perception of the deposit, and the judgement of the estimator. With reference to one particular deposit, East Bullakitchie, the series of resources statements published over a 5 year period is compared with the corresponding history of discovery and development. The comparison Illustrates:

Jan 1, 1990

The environment under discussion is that of the sandy coastal plain and adjacent offshore sandy islands. The environment is the result of natural forces of the past which moulded it. Only very recently have men and machines participated in this moulding. The future of the environment - the changes which it must undergo - is in the hands of natural forces with, presumably, man's continued participation. In essence, we are concerned with the forces operating on a mass of sand.

Jan 1, 1971

I.T.H. Drilling has been accepted as a tool used daily for both production and service work in Australian underground mines. For this reason, it is of interest to examine the rigs and drilling equipment in use to do this work, also to review the technique necessary to ensure that this drilling is done efficiently.

Jan 1, 1978

The Lower Palaeozoic Woolomin Association is composed of chert and jasper (often radiolarian), siliceous argillite, the mafic volcanics with associated hyaloclastites, and occasional greywacke and limestone lenses. Several "Cyprus-type", conformable pyritic copper (+/- zinc and cobalt} sulphide lenses are spatially related to individual mafic volcanic units and manganiferous chert and/or jasper. The Association has been interpreted to represent an oceanic crustal remnant generated either in an island arc environment (Herbert, 1981) or at a divergent plate boundary (Scheibner and Glen, 1972; Leitch, 1974a, 1975) later to be obducted, or tectonically emplaced, into continental crust; the adjacent Peel Fault was considered to be the palaeo-obduction zone (Scheibner and Glen, 1972) and the associated alpine-type mafic/ultramafic complex, an ophiolite (Crook and Felton,1975).

Jan 1, 1990

This paper discusses why Argyle Diamonds adopted thickened tailings disposal in 1985 and how the system was developed over the next seven years. A wide ranging review of the thickened tailings disposal system and the tailings deposit it was producing was carried out during 1992 and 1993. The results of that review led to the abandonment of thickened tailings disposal at Argyle because of serious concerns about the stability of the resultant tailings deposit. The exposure to the risk of liquefaction and an assessment of the consequences if this happened to the thickened tailings deposit are shown. The criteria for selecting the new tailings disposal strategy are then described. The final section of the paper discusses the management strategies that have been put in place. These are designed to: ò reduce the risk posed by the thickened tailings deposit to an acceptable level; ò safely store tailings to the end of mine life; ò produce a land form that can be decommissioned to the satisfaction of Government regulatory bodies.

Jan 1, 1996

By Carter LC

Following the perception by the Groote Eylandt Mining Company of a need to further beneficiate a fines product, and preliminary metallurgical testing to demonstrate the feasibility of such beneficiation, a comparison was made of the various configurations of cyclonic heavy medium separators available. This comparison consisted of (i) a pilot plant test in which a dynawhirlpool (DWP) and a pump fed cyclone were compared, and (ii) a survey of operating plants using the systems under consideration. Little metallurgical difference was found-between the different systems. The gravity fed cyclone configuration was finally chosen based on a particular need to minimise degradation of ore and on a desire, in so isolated a location, to use established and locally supported technology.

Jan 1, 1987

The Kalkadoon Granite is regarded as composite in character with at least two different phases. The older phase is considered older than the sediments of the Western Geosyncline, and the younger phase is considered younger than the sediments of the Western Geosyncline.Consequently, the older phase could be a time equivalent of the Ewen Granite, whereas the younger phase could not. An age of 1760 million years seems plausible for the older phase, and an age of 1540 millionyears seems appropriate for the younger phase.

Jan 1, 1967

By Canterford JH, Ritcey GM

With the development of new technology and materials of construction, chloride-based hydrometallurgical routes have gained accept- ance as a viable alternative to sulphate-based routes. A number of commercial and pilot plants built and operated over the last decade have provided invaluable experience and con- fidence in their use. Chloride hydrometal- lurgy, with or without pyrometallurgical pre- treatment, is particularly attractive for pro- cessing complex Cu/Pb/Zn/Ag concentrates, nickel mattes and chalcopyrite concentrates. This review outlines recent developments, dis- cusses advantages, as well as indicating some of the problems still to be solved.

Jan 1, 1984

Ore samples from the South, Central and North ore-bodies of the King Cassilis Mine, near Omeo, Victoria, were broken and transported to Melbourne for experimental metallurgical treatment. A microscopical examination of individual unoxidised specimens, selected from these samples, was undertaken in order to thro'w as much light as possible on the occurrence of the gold which forms the valuable economic mineral in the ore.The following descriptions are the outcome' of this examination and show that very minute particles of free gold are mechanically associated with the sulphides. While the gold may be separated from the transparent gangue minerals by the flotation of the sulphides, the, actual size of the particles indicates that it is impossible to separate all the gold from the sulphides by grinding the ore to pass through a screen of 200 mesh in which the average width of the holes is 0.063 mm. Chemical disintegration of the sulphides is essential to free all the gold particles and render them available to the attack of chlorine or of a solvent.It is interesting to recall that a metallurgical investigation on the Cassilis ore in the same district by K. A. Mickle in...

Jan 1, 1933

By Donchak P. J, Champion D. C, Fordham B. G, Domagala J

The Hodgkinson Province forms the northern part of the Tasman Orogen and contains the most extensive outcrops of Silurian - Devonian rocks in Queensland. Deep-water, marine siliciclastic sequences (mainly turbidites) dominate most of the province except near the western margin where mafic volcanics and fossiliferous limestones characterise much of the succession. It is difficult to apply normal stratigraphic mapping techniques to the Hodgkinson Province because of extensive stratal disruption by numerous thrust faults, the general lack of stratigraphic and structural markers, and the unfossiliferous nature of much of the succession. Nevertheless, several distinct units have been delineated although their internal stratigraphy or boundary or superpositional relationships are uncertain. Ordovician strata, as well as two major unconformities have been recognised in the western part of the province. Several models have been proposed to explain the evolution of the Hodgkinson Province. Although there is no general agreement most recent researchers favour an extensional tectonic regime.

Jan 1, 1990

The basic model for the evaluation of any coal-bearing property is the cash flow projection, the major components of which are operating costs, capital charges, taxation and revenue. A range of cash flow projections can be produced by varying the assumptions which underlie the operating costs, by assuming various forms of capital funding, by making assumptions as to future taxation and by speculating upon the present and future market value of the product. As for any model, the informational inputs and assumptions are vital because, no matter how sophisticated the processing, the informational inputs and assumptions cannot be improved by it. That is to say, the validity of the output (the total evaluation itself) cannot be of greater certainty or significance than that of the inputs. The total evaluation can of course be expressed in a number of ways such as the Discounted Cash Flow (D.C.F.) Rate of Return, the Net Present Value or, the Payback Period. The foregoing statement may seem trite. However, it is necessary to be clear about it so as to avoid unnecessary complication and a preoccupation with techniques as opposed to the informational inputs and assumptions. So far as techniques are concerned, much has been written and said about them during the last decade. Most of us have heard, if not always understood, something about probabilistic models, Monte Carlo simulation, sensitivity and risk analysis to say nothing of inflationary costing and the relative merits of developing cash flows in terms of current or constant money. Those techniques have their value, particularly if they can serve to illuminate conclusions which could not be reached on a simple and even perhaps on an intuitive basis. I am, however, reminded of one major coal mining project in which 20 or more major variables were identified, many cash flow projections were run on the computer and a detailed sensitivity analysis was carried out. The major conclusion reached was that the D.C.F. Rate of Return was predominantly sensitive to variations in selling price and operating cost. Of course, the funding and fiscal elements of a cash flow projection have to be dealt with as rigorously as possible. However, in the development of any coal property, capital requirements and taxation are, in part at any rate, dependent upon the assumed operational parameters. If the latter are misjudged, the whole evaluation process is deeply affected. The same is true of revenue, in the sense that, the positive cash flow is a function of output as well as selling price and again, misjudgements about achievable and maintainable levels of production also deeply affect the final evaluation. I shall try to underline the fundamental influence of the technological factors upon lead times, capital costs, operating costs, taxation, funding and the achievable and maintainable levels of production. In turn, these affect the whole question of coal property evaluation and indeed, the likely success or failure of any coal mining venture. I make no apology therefore that this paper does not set out to discuss the more esoteric aspects of the evaluation process but rather, directs attention towards some of the informational inputs and assumptions which merit clarification and discussion.

Jan 1, 1975

Currently, mining in Australia underpins the economic vitality of the nation, generating massive revenue from commodity exports and providing substantial infrastructure and employment. In addition, it is predicted that mining related services will in the future develop a global market of their own that could eventually grow to rival, in value, the export trade in mineral commodities. There is however little room for complacency. In the short- to medium-term, escalating, vigorous competition can be expected from many previously underdeveloped countries that are reforming their own mining and mineral export industries. In addition, most mining companies are facing a modem-day renaissance in terms of new expectations, changing social norms, evolving employee relations and statutory obligations. Thus, along with whatever promise the future might hold, the mining industry is currently being subjected to a growing number of largely unprecedented problems and pressures, both economic and social, that are both highly complex and demanding. In particular, it remains a matter of on-going concern that relations between mining companies and their employees still, in spite of recent reforms, continue to constrain productivity, perpetuate inefficiencies, affect quality of work life and retard progress towards mutually beneficial goals and achievements. If mining in Australia is to attain and hold on to a commanding position on the global scene, then further changes will clearly need to be made. Realisation of this appears to be growing, with most mining companies having attempted in recent years to improve workplace culture. Based on a wide ranging study, this paper presents an overview of what has been learned to-date with regard to the `people factor' when it comes to implementing and progressing positive change and reform in mining. From this, a number of practical suggestions, arising from hard won lessons and experiences in the field, are offered. Attention to the nine `key principles' given should help to ensure that many of the common problems encountered to-date with change and reform in the mining industry are in future avoided or at least minimised.

Jan 1, 1997