Search Documents

By C. E. St. Denis

"Training Program at Sherritt Gordon's Ruttar:. ConcentratorA formal training program for mill operators is being developed and employed at Sherritt Gordon's Ruttan Concentrator. The program was set up to fulfil the needs created by a shortage of skilled reliable labour, a 200% turnover of personnel within the first six months of operation and the rapid advances in mineral processing technology. All new employees are introduced into the Mill Department through an orientation program designed to familiarize them with the operation of the plant. All training and orientation of new employees is the responsibility of a. small training section consisting of two training foremen and one assistant. Using a combination of classroom and supervised on the job training, the training times have been cut by at least one half. High operating standards have been set and are maintained through the use of detailed manuals for each work area and competent instruction at all operating levels. The major portion of training costs arise from the salaries of the training staff but are negligible when compared to the improved recoveries, smaller turnover and less downtime. Government assistance is available to all industrial employers to offset the costs of training employees."

Jan 1, 1974

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

By Cale J. Dubois

At Cameco Corporations' Cigar Lake Project, large excavations are developed on the 480 Level and 500 Level must remain stable for at least 15 years to host underground processing infrastructure. Following the successful dewatering of the mine in October 2009, subsequent internal rockmechanics investigations augmented by third party technical investigations; determined that to keep the back of the Water Flush Crusher/Run-of-Mine (WFC/ROMs) excavation stable; required a rehabilitation strategy to mitigate deterioration/deformation of the WFC walls and intersection pillars. The mechanism of failure propagating the movement of the excavation walls is understood to be controlled by the presence of a dominant E-W striking and steeply dipping foliation within a relatively weak and mildly altered rockmass sub-parallel in strike with 14 meters high walls and an intersection span approaching 15 meters. The application of open and resourceful communications between site mining engineers, geologists, contract mining staff, construction management experts, corporate mining and civil engineers, and third party technical experts resulted in a multi-faceted short-term ground support strategy consisting of standard bolting and screening, deep-seated modified-strand cable bolts coupled with heavy gauge mesh straps, rockmass reconditioning using low-pressure grout injection, and horizontal cable-lacing for the intersection pillars applied in lifts using a top-down methodology. The intention of the short-term strategy was to stabilize the excavation so that a long-term structural steel support installation - consisting of composite concrete walls, and arch support applied to the side walls and crown of the back - could be constructed safely. This paper summarizes the evolution of the short and long-term ground support strategy and criteria for the WFC/ROMs excavation developed using elements of civil, mining and hydrogeologic design.

Nov 1, 2011

By Pierre Rocque

The Red Lake Mine is located approximately 600 km northwest of Thunder Bay. This 545 tpd (600 tons/day) underground narrow vein gold operation is set to produce in excess of 14.8 tonnes (475,000 ounces) in 2001 at a cash operating cost below 75 U$/oz. The high-grade nature of this deposit (>55 g/t or >1.6 opt) coupled with its complex geological environment and relatively deep location dictated the choice of a very selective primary mining method, Mechanized Overhand Cut and Fill. In addition to geological challenges, mine design issues such as material handling, ground stability and requirements for yieldable ground support are also discussed in this paper.

Oct 1, 2001

By George P. Demopoulos

For more than 20 years the author had the privilege of working closely on a number of R&D projects with Lucy Rosato and her team at CEZinc. Several of these projects were driven from the sustainability agenda that Lucy Rosato championed as an innovation leader that supported research collaborations. Highlights from this highly rewarding collaboration are to be presented in this paper. In particular we will deal with the following works-topics: (a) iron control via solvent extraction as alternative to jarosite precipitation; (b) production of high-density gypsum by controlled neutralization of simulated zinc plant process/waste waters; (c) selenium removal from weak acid solutions; (d) electrolyte purification by cementation; and (e) manganese control by oxidative precipitation with SO2/O2.

Jan 1, 2015

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By Paul Girodo

Government Approval For Foreign Workers 1.Service Canada Work Permit Tasks: i. Prove there are no Canadian Journeymen; ii. Use heavyweight stakeholders; iii. Understand the FWU transformation taking place today. Government Approval For Foreign Workers 2.Provincial Nominee Program (PNP) i. Build relationships; ii. Use heavyweight stakeholders; iii. Continually demonstrate benefits to the Province from foreign Journeymen. Government Approval For Foreign Workers 3.Letter from Union Supporting Temporary Foreign Workers i. Easiest path to approval ?CLAC model

May 1, 2006

By I. S. Parrish

The Sullivan Mining Group has been exploring the mineral deposits of the Mount Pleasant area of southern New Brunswick since 1967. Sullivan geologists have logged over sixty miles of drill core, mapped over five miles of underground workings and studied numerous surface exposures. Several mineralized zones have been defined and two higher-grade porphyrytungsten bodies delineated. Within these bodies, wolframite occurs as disseminated specks and grains up to one-half inch in diameter. The host rock is a brecciated rhyolite porphyry that has intruded quartz-feldspar porphyry of Mississippian age . The host rock is itself intruded by an acid porphyry called transition rock and is underlain by a microgranite. The mineralized zones, host rock, transition rock and microgranite are all thought to be derived from the same magma, and to represent progressive fractions from that magma.

Jan 1, 1978

By Neil Westoll

But First, An Overview of the Selwyn Basin and Its Resources ?World-renowned sedimentary-exhalative (SEDEX) deposits of zinc, lead, silver +/-barite ?Significant reserves/resources remain and vast tracts of prospective stratigraphyremain under-explored and untested. ?More details are at the Yukon Geological Survey?s Selwyn Basin Metallogenysite:http://www.geology.gov.yk.ca/metallogeny/selwyn/ Overview of Metal Price and Demand Trends ?The pace of economic change in China has been extremely rapid since the start of economic reforms just over 25 years ago. According to official statistics, economic growth has averaged 9.5% over the past two decades and seems likely to continue at that pace for some time. National income has been doubling every eight years. Such an increase in output represents one of the most sustained and rapid economic transformations seen in the world economy in the past 50 years.? Organization for Economic Co-operation and Development 16-Dec-2005

May 1, 2006

By W. S. Dyer

Considerable attention has been paid in recent years to the fire-clay and silica-sand deposits of the Mattagami and Missinaibi rivers and ? to the lignite occurring in them. The fireclay especially deserves this attention; it is of first-class quality; it appears to be widespread; it is the only fire-clay in central Canada, and part of it lies not more than 20 miles west of Coral rapids, to which point steel will be laid this coming spring by the Temiskaming and Northern Ontario railway. Undoubtedly, these clays will rapidly find a place in industry. The fire-clays and the better grades of silica-sand are Mesozoic in age and have been referred to the Lower Cretaceous or Upper Jurassic. Glacial clays and sands and Palaeozoic shales also occur in the same region, but are of little economic value, and will not be dealt with in this paper. Dr. Robert Bell was perhaps the first to discover the clays, since in the Report of Progress of the Geological Survey of Canada for 1877 and 1878 he reported beds of lignite on Coal brook, a tributary of the Missinaibi river, underlain by sticky clay and overlain by glacial drift. In 1880 E. B. Borron (1) discovered an extensive deposit of white sand and clay on the east bank of the Missinaibi river, five miles below Coal brook, and in 1890 (2) he examined the deposit found by Dr. Bell on Coal brook. He recognized that the underlying clays were quite distinct from the glacial clays of the region, and suggested that they might be used for fire-brick if metallurgical operations were undertaken in the region. Somewhat later, J. M: Bell described a deposit of fire-clay and silica-sand on the Wabiskagami river, another tributary of the Missinaibi.

Jan 1, 1928

By Champoux. G., E. Ghali, W. Zhang, G. Monteith, A. -M. Lafront, G. Houlachi

The efficiency of the electrowinning process of zinc depends on the performance of oxygen evolution reaction, anode quality and corrosion resistance of lead anodes. Original surfaces of rolled commercial lead-silver anodes were examined using conventional polarisation methods in acid zinc sulfate electrolyte with manganese sulphate at 38 °C. The self-discharge method (potential decay) following 5 h polarisation at 50 mA cm-2 was considered to evaluate electrochemical activity, oxygen overpotential and anode stability. The influence of silver content is compared to that of the microstructure, the fabrication process and the composition of the corrosion products. Polished anode samples have also been examined for microstructural and corrosion performance studies. The experiments show that the duration of the plateau at 1600 mV versus SHE, the potential level (active corrosion state/stationary state) and the rate AEco/At during the decay could be a good indicator to compare the corrosion rates of the anodes in industrial zinc electrolytes.

Jan 1, 2008

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By Benjamin H. Clark

"For over 50 years, Derrick Corporation has been renowned for its innovative and durable fine screening equipment and screen surface technology. Derrick’s latest innovation, the patented Stack Sizer, offers mineral processors both high tonnage capacity and high separation efficiency on an extremely small footprint.The Stack Sizer is suitable for separations from 6.3 mm down to 75 microns (200 mesh). The Stack Sizer, coupled with Derrick’s patented urethane screen surface technology, offers an extremely economical alternative to hydraulic classifiers, hydrocyclones, and less efficient low volume wet screening systems. Stack Sizers have been used in feed preparation for flotation, spirals, and a variety of jigs. Mineral processors wishing to reduce grinding circuit circulating loads and generation of slimes due to over grinding, thereby enhancing the efficiency of flotation and gravity circuits, now have another technology at their disposal to perform this critical sizing and grade control function.Over 200 Stack Sizers have been installed in numerous mineral processing applications worldwide attesting to the rapid acceptance of this technology. Stack Sizers are currently screening ferrous and non-ferrous metal ores, mineral sands, silica sand, kaolin clay, feldspar, garnet, phosphate, aluminum dross, potash, coal, tantalum, spodumene, niobium, and other rare earth mineral ores.INTRODUCTIONDerrick engineers have long understood and demonstrated the importance of screen width in coupling both high capacity and high separation efficiency for fine wet sizing applications. As opposed to fine dry sizing, where the length of the screening machine is critical for high separation efficiency, introducing slurry feed to screens in a thin and even layer at minimal velocities across wider screen surfaces allows for high capacities and efficiencies, with maximum screen cloth life. This is due primarily to the combination of free liquid and high frequency vibration of the Derrick motors, which allow fine undersize material to pass through the screen apertures. Lacking either of these factors would be extremely detrimental to the screening process. Without the high frequency vibration of the motor, the screen is essentially a low efficiency sieve bend. Without the free liquid to carry fines through the screen openings, the screen is for all intents and purposes a glorified conveyor or dewatering unit, as little or no sizing takes place once the screen is devoid of free liquid. For optimal screening results, Derrick recommends feeding slurry to a screen at approximately 20% solids by volume. Figure 1 shows the Stack Sizer design concept. Note that a single feed point is used to evenly distribute the flow to the five separate feed points."

Jan 1, 2007

By N. Shi, T. G. Joseph

The design of dippers for cable shovels has essentially remained unchanged for the last 100 years. In the past 10 years, shovel manufacturers have started taking another look at dipper design, resulting in changes that have borne models from major manufacturers that address some of the wear conditions and material retention problems that dominate maintenance and operational costs. However, with the exception of added lateral curvatures to the front and corners of the dipper, the geometry is essentially unchanged. This paper looks at the criteria that have resulted in the first new cutting dipper design in a century. The design is based on kinematic considerations, reflected in a revolutionary geometry that matches the range of motions of the shovel, designed to minimize wear, impact loading and power required to dig, thus maximizing productivity for a minimum energy requirement. The shape configuration is such that the weight of the dipper is reduced through wall thickness, enabling a larger capacity dipper to be conceived for the same shovel. Benefits are reflected in reduced operational and maintenance costs and increased productivity.

Jan 1, 2006

By C. E. Rodgers

WHEN I was asked to prepare, for presentation at the 1938 Annual Meeting of the Institute, some data concerning low-discharge grinding at the Sylvanite mill, it seemed entirely reasonable to expect to have at my disposal the results of at least four full months' operation after the last unit, as then proposed, was installed. Delays in delivery of equipment, nevertheless, shortened the interval, as will be shown herein. In submitting the data contained in this discussion, I wish distinctly to state that the intention is not to claim that final conclusions can be reached at this time concerning our operation. Test periods, in certain instances at least, have been too short for this purpose, although some, where so stated, have been extended through March and April. It is hoped, however, that an advantageous trend in practice can be shown and that the experience related may be of interest to others who are now operating, or who are considering the operation of, low-discharge grinding mills. In the plant under review, four mills are in use: one primary and three secondary. Present mill capacity (grinding, as shown by screen test, about 99 per cent through-200-mesh and approximately 88 to 89 per cent minus-325-mesh with infrasizer giving about 90 per cent of the latter) averages about 525 tons per day. A brief description of each unit will be given and comments will also be made relating to operation. This will be followed by certain test data from which, in conclusion, operating results are summarized.

Jan 1, 1938

By Ian McC. Stewart

"Seam gas flow in coal mines takes place through a medium which has both capacity and resistance and can therefore be expressed in terms of the basic diffusion equation, provided that the characteristics of the system can be adequately described. It may be possible to lump the variations from point to point in a seam together as an effective diffusivity. The paper discusses the characteristic flow-time patterns for various types of openings and the particular features of coal and seam which influence the diffusivity.Two field experiments are described in which gas make to a heading and to a borehole were measured in a mine for which considerable data on coal sorption properties were available. Incremental gas flow measured from the borehole experiment predicted the actual flow from the heading measurements remarkably well. The effective permeability adjacent to the face was much higher than expected from the properties of the coal. The incremental flow measurements to a horizontal (in-seam) borehole showed a striking picture of advancing 'relaxation' behind the face which is not discernible by other experimental means."

Jan 1, 1971

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By P. S. Capper

"Generally speaking, the most intensive efforts at dust control in the mining industry have, in the past, been concerned with underground operations and where uranium ore or high silica material is processed. In the past several years, Stoop Rock has made Intensive efforts to reduce dust levels in it's Iron ore pelletizing complex. There have been no great engineering break-throughs with regard to dust control in such plants, and certainly no new engineering techniques have had to be applied at Steep Rock. This paper deals with how significant improvements in dust levels have been achieved through minor modification to dust collectors and ventilation units, improvements in operating practices, and education of supervisors and hourly personnel.PROCESS DESCRIPTIONSteep Rock Iron Mines is located 120 miles west of Thunder Bay near Atikokan. (fig. 1) Run-of-mine ore is pelletized along with some -1"" concentrate that has been processed in the concentrator (a summer operation only), which utilizes gravity separation to upgrade a mechanical mixture of ore and waste."

Jan 1, 1976

By J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

"The Niobec concentrator rejects up to /5% of the Nb as slimes (-10u.m). The recovery of Nb from these slimes by column flotation is being studied. An essential condition for selective flotation is slimes dispersion. A particle size analyzer, the Sedigraph 5000D, was used to monitor dispersion in plant waters with combinations of organic and inorganic dispersants and flotation reagents. Flotation reagents were particularly detrimental to dispersion with sodium silicate. The best dispersion conditions were selected for column flotation tests. These tests revealed that reagent combination had a pronounced effect on froth stability. Careful frother selection achieved good froth stability under conditions of good dispersion. Plant water increased the required dispersant concentration causing mineral depression.IntroductionSlimes (-10 u.m) rejected at Niobec contain up to 15070 of the over-all Nb content . Recovery of Nb from these slimes would significantly increase over-all recovery. A suggested recovery route involves two phases: (1) carbonate flotation (to remove most of the carbonates) depressing silicates and pyrochlore (as currently done at Niobec); and (2) selective (direct) pyrochlore flotation from the silicates. Phase 2 has been addressed and several routes to achieve selective flotation are available. Phase I was attempted with the selective reagent scheme used at Niobec but a considerable amount of pyrochlore floated with the carbonates due to poor slimes dispersion."

Jan 1, 1987