Search Documents

By Victor Azbe

Azbe System of Controlled Calcination To obtain good and cheap lime there are certain fundamental requirements that need to be satisfied. These are : (1) Proper combustion of fuel and steady supply of heat to the kiln. (2) Proper heat distribution in the kiln. (3) Uniform drawing of lime through the several shaft sections. (4) Complete cooling of the lime and recovery of the heat. (5) Temperature control of the hot zone by economical means. (6) Ample draft to obtain high capacity. (7) Arrangements to facilitate operation. Figure 17 shows diagrammatically one of the smaller kilns, intended for large stone. Such a kiln can be supplied with gas from a centrally located automatic gas producer, or, as shown, from an integral producer located snugly against the kiln. These producers make very good gas and have a gasification capacity of either 10 or 15 tons of coal a day. The producers have water-sealed ash pits, a rather thick fuel bed that is conducive to the making of high-CO gas, and are under forced draft. No steam is used. Clinkering is prevented by admixing some spent gas from the kiln with the air. Coal feeding is from a coal bunker through spouts into the hoppers over the producer. This is done, at proper intervals, by manual operation of slides, but it is planned to install mechanical feeders. Central mechanical gas producers have the advantage of requiring little labour, but the blowing of soot is a problem, as also is the proper distribution of the gas among several kilns. In the case of integral gas producers, soot from the centre burner is blown back into the producer to be burned, and the supply of gas to the kiln is controlled by regulation of air to the producer. In large plants, the mechanical producer may be preferable, but in small ones, the integral producer is cheaper, better, and more reliable. The kiln shown in Figure 17 is suitable for both systems of gas supply. It will be noticed that there are no side gas burners. All gas enters the kiln through the centre burner in a manner that permits any desired amount of gas to be directed to any of the kiln sections by the aid of regulating slides.

Jan 1, 1946

Experimental Mine, Val d'Or, Quebec, Experiments on the ignition of sulphide dust clouds by explosives have been conducted in a 1 m3 explosion chamber. The explosives tested are ANFO, emulsion, aluminized emulsion and Detasheet. By controlling the composition of the ANFO and the emulsion explosive the oxygen balance could be changed in order to identify the dominant factors in the ignition of sulphide dust clouds by explosives. Experimental results, combined with theoretical calculations, show that the temperature of the detonation products is the most important parameter in the ignition of the dust cloud while the combustible detonation products are of secondary importance in the case of non-aluminized mining explosives. In the case of aluminized explosives and explosives having very negative oxygen balance the ignition of the dust cloud is assisted by the large amount of combustible detonation products.

Jan 1, 1993

By G. E. Agar

This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady-state balance can be calculated for a circuit. Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative technique to arrive at the steady-state balance. The program is written so that a variety of circuits can readily be simulated. A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets are presented on sulphide ores, on copper-nickel separation and on silver flotation.

Jan 1, 1978

By W. E. Coates

The social ecology of surface mining in urban areas is illustrated by a case study of a recent application for the opening of a new gravel pit in the city of Guelph, including the design of a progressive extraction-rehabilitation sequence for the property, investigation of the ecological impact of the proposed operation, history of the application procedure for a zoning change and the relationship of the operating plan to provincial legislation controlling surface mining.

Jan 1, 1972

By John Lindsay

Outline ??Recovery plant requirements and concepts ??Common recovery plant unit processes ??Recovery plant design considerations ??Peripheral issues Process Design ??Liberation ??Separation ??Recovery Processing ??Density 3.5 g/cm3 ??Luminescent under x-ray ??Hydrophobic (non wettable) surface ??Non-magnetic ??Inert to strong acids / bases

Apr 1, 2005

By Linlin Tong, Xiangling Song, Guobao Chen, Zhenan Jin, Hongying Yang

Biooxidation of a high arsenic-bearing refractory gold ore was investigated to determine the arsenic removal efficiency by the cultured bacteria and to examine the effect of biological pretreatment on subsequent gold cyanidation. The biooxidation pretreatment process utilizes the ability of adapted acidophilic bacteria to oxidize pyrite and arsenopyrite and release the encapsulated gold. The released gold can be efficiently extracted by the subsequent cyanidation process. The biooxidation experiments were conducted with cultured bacteria using various sizes of agitation tanks. Leaching results showed that over 96.26 % arsenic extraction could be obtained from this ore after 6 days of bioleaching with continuous stirred tank reactor (CSTR). Gold extraction during the cyanidation process was increased from 29.35% to 96.71% after biological pretreatment. The content of arsenic in the biooxidation residue was reduced to below 0.3%. The transformation process of As was considered as [AsS]2- ? As (?) ? As (?) during the biological pretreatment.

Jan 1, 2014

By B. J. Walsh

ABSTRACT Segregation of sphalerite minerals in zinc concentrates into christophite, marmatite and ordinary sphalerite by means of magnetic fractionation is investigated. A Frantz ferromagnetic filter, 1.2 amp., and a Dings magnet, 0.3 amp., is used to fractionate seven zinc concentrates produced in the Province of Quebec. The Dings magnetic product contains the pyrrhotite, and the sphalerite as christophite. The Frantz magnetic product contains sphalerite as marmatite, while the Frantz nonmagnetic product contains ordinary sphalerite. The results indicate that the magnetic susceptibility of sphalerite increases with increasing isomorphous iron content and that a satisfactory separation into christophite, marmaite, and ordinary sphalerite may be accomplished by magnetic fractionation. INTRODUCTION SPHALERITE, the chief ore of zinc, is almost never pure zinc sulphide. Iron is almost always present isomorphously replacing an ?equivalent amount of zinc. What may be referred to as 'ordinary' sphalerite contains up to 10 per cent iron. More highly ferriferous varieties, with 10 to 26 per cent or more iron, have been named marmatite .and christophite.

Jan 1, 1951

By I. M. Gordon, J. Blackshaw

"Run-of-mine ore is reduced to 4 per cent on 4 mesh (3/ 16 inch), using four stages of dry crushing. The mill feed is then reduced to 2 per cent on 48 mesh and 60 per cent through 200 mesh, using one stage of ball milling in cyanide solution. During the subsequent treatment about one-tenth of the tonnage is removed as a table concentrate and ground to 77 per cent through 325 mesh. The size of the mill tailing is 66 per cent through 200 mesh.Four stages of ore reduction began when the dry crushing plant at No. 26 Shaft came into operation at a maximum rate of 440 tons an hour on July 31, 1941. A detailed description of the crushing plant was published in C .I .M. Trans., Vol. LVI, 1953.One-stage ball milling in cyanide solution came into full operation on January 11, 1938. The ball milling plant had a capacity of 4800 tons daily when reducing mill feed at 2. 7 per cent on 1/ 4 inch to 54. 3 per cent through 200 mesh. Primary grinding to 60 per cent through 200 mesh commenced May 22, 1945, when the feed was 3 per cent on 4 mesh. Under these conditions the capacity of the ball milling plant is estimated at 4300 tons daily. A description of the 11 Hollinger Crushing and Grinding Plant"" by D. C. McLaren was published in the Canadian Mining Journal, June 1944.The concentrate grinding circuit using a 7 x 15 low discharge ball mill and a 19-foot diameter bowl classifier with a 6-inch centrifugal pump to close the circuit began operating in the ball milling plant on October 24, 1939."

Jan 1, 1965

By Fred V. Seibert

The Functions and the Responsibilities of the Institute The Canadian Institute of Mining and Metallurgy is unique. ln addition to the welfare of its members, it has a real interest in the welfare and promotion of one of Canada's largest and most important basic industries. It is because of this that the membership is composed of both individual and corporate members. The individual members are both technical and non-technical (Members and Associates). Both Members and Associates have the same status in the Institute and all are interested in the welfare of the mineral industry. The aims and objects of the Institute 11re twofold. The education and welfare of its individual members and the sound promotion and welfare of the mineral industry. Perhaps it might be well if we reviewed these aims and objects as stated in our Constitution: "First - To promote the arts and sciences connected with the economical production of valuable minerals and metals, by means of meetings for the reading and discu11ion of technical papers, and the subsequent distribution of such information as may be gained throo.gh the medium of publications". It cannot be denied that we have do ne a good job in this particular phase of our work. Nevertheless, there is still room for improvement. It has been suggested that we might have more discussion and, on occasions, more criticism of our papers and programmes. This can best be done if the authors will have their papers prepared in sufficient time to permit of preprints being made availa1ble before the meeting at which they are to be presented.

Jan 1, 1950

By R. Lasmanis

"Washington State's diverse geological setting is reflected by its several types of porphyry Cu-Mo deposits. All are associated with calc-alkaline intrusions, and they range in age from Jurassic to Miocene.The largest is the Mount Tolman Mo-Cu deposit located in the Omineca Belt. It contains 2.18 billion tonnes of material averaging 0.093% MoS2 and 0.09% Cu. There are intermediate-size Mesozoic deposits in the Intermontane Belt. The Cascade volcanic arc hosts small- to medium-Tertiary deposits. Among these, of particular interest is the Sunrise breccia pipe, which has been explored over a vertical distance of 1000 m. It contains reserves of 64.6 million tonnes averaging 0.319% Cu and 0.071% MoS2 with significant tungsten values. The Glacier Peak deposits have potential resources of 1.7 billion tonnes averaging 0.334% Cu and more than 0.015% MoS2 and also contain tungsten. The Margaret deposit can be classified as a porphyry Cu-Au type; it has reserves of 200 million tonnes averaging 0.434% Cu, 0.0175% MoS2> 0.27 g!t Au and 1.92 g!t Ag. Drill intercepts of the North Fork deposit also show significant gold values.Mineralization and hydrothermal alteration of these deposits are typical of porphyry deposits, although some differences can be noted. The Mount Tolman molybdenum deposit contains topaz alteration zones and is transitional between a plutonic type and a Climax-type molybdenum system. Other deposits, such as the Kelsey, Mazama, North Fork, and Margaret, are low-sulphide systems that contain significant amounts of magnetite."

Jan 1, 1995

By V. Bazhko, V. Yahorava

The calcium sulphate waste stream of the wet phosphoric acid process, commonly called phosphogypsum (PG), contains the majority of rare earth elements (REE) initially present in the apatite feedstock. Mainly light and middle REE are present in PG and their total concentration ranges from 0.27% to 0.35% by mass. Worldwide, around 7 billion tonnes of PG have been produced to date at a current growth rate of 150-200 million tonnes per annum. In total, an estimated 21 million tonnes of REE are locked in PG waste dumps around the world. Due to the value of the REE contained in PG dumps a number of processes have been devised for their recovery. The majority of these processes applied complete or partial gypsum dissolution, but were deemed not viable due to high capital and operating costs. Mintek developed an alternative method for the recovery of REE from PG by applying Resin-in-Leach (RIL) technology. This technology was tested on PG sampled from dumps and current arisings from South African phosphoric acid production plants. The extensive testwork program included evaluation of various lixiviants and optimisation of lixiviant additions, optimisation of REE leach and adsorption conditions, batch equilibrium and kinetic adsorption tests, continuous RIL testwork and numerous variability tests. It was found that PG from different sources was highly variable, both in terms of REE recovery as well as physical properties of the material such as viscosity and filterability of the slurry. The recovery of REE varied from 15% to 80% depending on the origin of the samples. A high-level economic study indicated that at a price of >21 $/kg for mixed REE oxide product in conjunction with an overall REE recovery as low as 15% the economics of REE recovery from PG via RIL technology may already be favourable.

Jan 1, 2016

By P. C. Thurston, T. Setterfield, D. H. Watkinson

"The Maybrun copper deposit IS In a succession of pillowed basaltic flows in the Wabigoon sub-province, northwestern Ontario. The rocks have primary flow morphologies and remarkably well-preserved crystallization textures, including quench-textured plagioclase, in spite of metamorphism to the amphibolite facies. The sulphide assemblage chalcopyrite-pyrrhotite-cubanite with minor sphalerite and pyrite is primarily in interpillow spaces and is stratabound. Basaltic rocks immediately enclosing the copper sulphide minerals have an enrichment in Fe, Mg and K and depletion in Ca and Na relative to surrounding flows. The Maybrun deposit is interpreted to have formed contemporaneously with volcanism and alteration, and was subsequently metamorphosed with the enclosing basalts.IntroductionThe association o f significant base metal accumulations with mafic submarine flows in the Archean is as yet poorly documented. Such deposits, where noted, have typically been small, and are therefore commonly over looked. The Maybrun Mine, a 2.6 x 106-tonne copper deposit in pillowed basalt, has many similarities with large, well-documented volcanogenic deposits. Given the interpretation of the Maybrun Mine to be volcanogenic in origin, there is n o reason why similar processes could not produce large deposit s. This is an important realization in an area where Archean submarine mafic rock s are very common, but frequently are examined only superficially. As gold commonly occurs in deposits such as Maybrun, even modest-sized deposits may be economic. The basalts at Maybrun are remarkable for amphibolite-facies rocks because of their extremely well-preserved delicate volcanic textures, including quench textures.The Maybrun Mine is one kilometre south of Atikwa Lake, in the Wabigoon sub-province of the Superior structural province, 75 km southeast of Kenora, northwestern Ontario, at longitude 93°35'W, latitude 49°25'N (Davies, 1973). Archean metavolcanic and metasedimentary rocks and intrusions underlie the area. Goodwin (1970) concluded that the mafic and minor felsic metavolcanic rocks, as well as the overlying metasedimentary rock s, were an eastward extension of the lower cycle of the Keewatin type section for the Lake of the Woods area. He estimated that the stratigraphic thickness of Keewatin rock s in this area is about 6900 m, of which 87% is basalt. The flows contain numerous interlayered sills, predominantly of basaltic composition; they have been extensively folded, faulted, metamorphosed to amphibolite facies and intruded by numerous felsic bodies, most importantly the Atikwa Batholith."

Jan 1, 1983

By A. Taylor, E. Thorn Corthay, J. Farrell, L. A. Westfall, S. Borchardt

Mining and metallurgical industries need to minimize their greenhouse gas (GHG) emissions; Hatch specializes in conducting mining and metallurgical energy management assessments and optimizing productivity. Projects executed have demonstrated that there is a wealth of energy management, waste reduction, and process efficiency improvements that require no or low capital investment. Typical energy cost savings are on the order of 5% to 12%, with similar reductions in GHG emissions. Hatch generates Marginal Abatement Cost Curves to optimize the implementation pathway, maximizing carbon abatement and minimizing cost. The findings of a practical case study from Cameco are presented.

Jan 1, 2010

By C. O?Connor

With ever-increasing global demand for mineral resources, numerous mines are moving towards developing and mining deeper, more complex and lower grade ore bodies. In many cases, mass mining methods (e.g. block caving) are being considered to deal with deeper, lower grade deposits. The body of practical knowledge, however, related to the impacts mass mining methods have on the surface environment in terms of rock mass response, subsidence, etc., is limited, imposing both economic risks to the mine and safety risks to mine personnel. This paper presents the framework for and preliminary results from a large collaborative research initiative between Diavik Diamond Mines, Rio Tinto, the University of British Columbia (UBC) and Simon Fraser University (SFU). The project involves the integration of available subsidence, rock mass, mine operation and monitoring data, together with the advanced application of combined finite/discrete-element modelling codes capable of simulating fracture behaviour, cave propagation and surface subsidence above block cave mines. The main objective of this work is to develop advanced numerical modelling methods to characterize complex rock mass behaviour above block cave mines. The research will also include the study of rock deformation mechanisms associated with the transition from surface to underground mining and the potential interaction between simultaneous open-pit and underground mining operations.

May 1, 2007

By D. R. Boyle

"The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite _ arsenopyrite _ galena _ Bi-Sb sulfosalts _ chalcopyrite _ tetrahedrite group _ sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was transported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By D. R. Boyle

"Abstract - The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite > arsenopyrite > galena > Bi-Sb sulfosalts > chalcopyrite > tetrahedrite group > sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was trans- ported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By D. L. Putnam

Snap Lake Mine ?? Complex dyke ore body ?? Underground operation ?? 1.1 million tonnes per annum ?? 1.2 carats per tonne ?? On-site diesel power generation ?? Supply by ice road and air ?? Milestones ? Construction commenced in 2005 ? Commissioning 2007 ? First diamonds August 2007

May 1, 2008

By M. J. Michaud, M. J. Lavigne

"A cornerstone of any successful mining project is an understanding of the mineral assemblage and metal distribution comprising the deposit. Knowledge of the precise mineral/ metal zoning enables an operation to utilize different mining and processing methods optimized for different parts of the deposit. The Lac des Iles mine, located in northwestern Ontario, is one operation that depends on a good understanding of these issues. Current resources for the Roby Zone total 94.1 Mt grading 1.66 g/t Pd, 0.18 g/t Pt, 0.14 g/t Au, 0.062% Cu, and 0.053% Ni.The Roby Zone occurs within the gabbroic portion of the Lac des Iles intrusive complex and consists of three compositionally and texturally different ore types with variable PGE, base and precious metal contents. PGE occur as sulphides and bismuthotellurides in net-textured sulphides, coarse sulphide blebs and as finegrained inclusions within secondary silicates.Knowledge of the precise mineral/metal zoning has directly and indirectly improved several operational aspects, including resource modelling, mining, and processing. For example, metallurgical recoveries have been increased by up to 3% to 5% and concentrate grades have increased by up to 100%. IntroductionLac des Iles Mines Ltd., a wholly owned subsidiary of North American Palladium Ltd., owns and operates a 3000 t/d open pit mine and concentrate facility, located 100 km north of Thunder Bay in northwestern Ontario. The Lac des Iles PGE-gold-copper-nickel mine has been in commercial production since 1993 and in 1997, produced 1.8 million grams of palladium, 127 000 g of platinum, 114 000 g of gold, 438 000 kg of copper and 354 000 kg of nickel (North American Palladium Ltd., 1998).Under the Industrial Research Assistance Program (IRAP), a two-year study of the mineralogy of the Roby Zone was undertaken with a goal of improving the profitability of the mine. Geological mapping, petrography and geochemistry of the Roby Zone were completed during this study. Utilization of the detailed mineral/metal zoning identified as part of this study was implemented at the mine and shown to positively impact many operational aspects including mining and processing."

Jan 1, 2003

By Chuan-Jian Zhong

Gold-based nanoparticles in the size range of a few nm have attracted increasing interests in catalysis, sensors and biomedical applications. The study of the unique catalytic properties of nanosized gold was inspired by the pioneering work of Haruta on the nanogold-catalyzed CO oxidation (1-4). There have been a number of excellent reports discussing both fundamental and application aspects of gold nanoparticles in catalysis (3-8). Our work reported herein is aimed at investigating the preparation and application of gold and its alloy nanoparticles for potential applications in fuel cell catalysis. Fuel cells operating by electrochemical oxidation of hydrogen or methanol fuels at the anode and reduction of oxygen at the cathode are attractive power sources due to their high conversion efficiencies, low pollution, lightweight and high power density. While methanol offers the advantage of easy storage and transportation in comparison with hydrogen fuel cell, its energy density (~2000 Wh/kg) and operating cell voltage (0.4 V) are much lower than the theoretical energy density (~6000 Wh/kg) and the thermodynamic potential (~1.2 V). The poor activity of the anode catalysts and inefficient activity or issue related to "methanol cross-over" at the cathode electrode are associated with the loss of about one-third of the available energy at the cathode and the other one-third at the anode. Extensive studies have been focused on Pt-group metals (Pt+Pd+Rh+Ru+Ir (PGM)) for both anode and cathode catalysts. A major problem is the poisoning of Pt by COlike intermediate species (9,10). Recently, oxide-supported gold nanoparticles in the <10 nm size range have emerged as one of the best catalysts for CO oxidation (1-3,11), and for water gas shift reaction in reforming stage using 5 nm Au on Fe2O3 (6). Gold and its alloy with other metals in the nanosize range present new alternatives (2,12). Whether the unique properties of gold nanoparticles can be exploited for addressing these problems is a focus area of our work. The ability to harness the large surface area-to-volume ratios and the unique surface sites of nanoparticles in <10 nm size range, especially in heterogeneous catalysis, constitutes a major driving force in fundamental research and practical applications of nanoparticle catalysts. It is this size range over which the metal particles undergo a transition from atomic to metallic properties. The understanding of factors controlling the morphological and surface reconstitution associated with such a size range is of fundamental importance to the ultimate exploration of nanostructured catalysts. We have been investigating the interfacial structures and properties of core-shell types of nanoparticles consisting of gold or alloy nanocrystal cores and organic monolayer shells that were prepared by twophase synthesis (13) and processing (14) protocols. Important attributes of such nanoparticles include controllable size monodispersity, processibility, and stability towards size- and composition-tunable catalysis (15-21). Some of these attributes were studied for understanding their electrocatalytic properties in the oxidation of methanol and reduction of oxygen, which are of fundamental interest to fuel cell technology.

Oct 1, 2003

By R. C. Fernandes, F. L. Santos

Aluminum alloys in particular, have certain limitations when subjected to welding process. This is mainly present because aluminum alloys have high thermal conductivity, high contraction in solidification and high hydrogen solubility. Taking this into account, the FSW process has great potential for this application, since it is autogenous, held without metal melting and without the use of slags or shielding gases. From this concept, the aim of this study is to evaluate the joining of thin sheets of aluminum alloy 3105 H26 with 0.7 mm of thickness. To performing of the tests, some parameters were analyzed, such as: tool penetration in the sheets, attack angle, the type of welding tool and penetration control mode (position or force). The results indicated that the force control mode is most suitable for thin sheets, and the transient state at the beginning of welding was the most critical part to control the welding quality.

Jan 1, 2015