Search Documents

"This paper describes some of the methods and equipment used for fine milling of minerals, and gives particular attention to the Vibro Energy system.In addition, the paper describes a specific application in the gold mining industry. This is the 200 tpd plant built by Anglo American Corporation at the President Brand Mine in South Africa in 1985, now a division of Freegold. This plant treats a gold bearing pyrite flotation concentrate which is finely ground to 15 microns prior to cyanidation and carbon-in-pulp (CIP). l .0 INTRODUCTIONFree milling gold ores are those that yield acceptable dissolution and recovery of the gold following grinding to what can be described as normal fineness, frequently between 50% and 90% passing 74 microns.Increasingly, gold metallurgists are faced with ores that are refractory. The traditiona1 treatment route for refractory gal d ores and concentrates has been by roasting, but for environmental reasons this is becoming less acceptable, or in some areas of the world, totally unacceptable. New methods of treating refractory gold ores are being developed and applied in practice. These new methods include pressure and biological oxidation. Higher gold liberation can also be attained by increasing the fineness of grind, although with conventional systems there are economic limits to this.In flowsheet development and test programs on new deposits, a standard procedure is to establish the relationship between the grind and subsequent go 1 d extraction. The normal situation is that gold extraction increases as the ore, or concentrate, is ground finer. Typically, this relationship is as shown in Fig. l, where the incremental additional extraction is very small once an optimum, or economic, grind has been achieved. This generally app1ies whether the material is free milling or refractory. The limits to grinding are set by the type of equipment which is commonly in use, usually ball mills. These mills have the obvious advantage of high capacity, however, they are increasingly inefficient as finer grinds are required. In general, ball mills are used to reduce ore to some agreed percentage passing 74, or possibly 53 microns."

Jan 1, 1988

By M. J. Fairweather, Keith Lee, Naseem Mian

"The initial metallurgical response of the lead flotation circuit at Cominco Alaska's Red Dog Mine was substantially below feasibility expectations. A program of diagnostic mineralogical analysis pointed the way to a number of process improvements, including simplification of the flow sheet and installation of a large flotation column as a lead cleaner. A diagnostic mineralogical analysis of the improved circuit shows that inadvertent activation of both sphalerite and pyrite has been substantially reduced, resulting in significant improvements in metallurgical performance. Directions for further improvements to the circuit performance are suggested by the recent analysis.IntroductionRed Dog is a high-grade, sedimentary exhalative (sedex) deposit with relatively simple mineralogy. The primary non-sulphide gangue minerals are quartz and barite, with minor barium carbonate (witherite). The iron sulphate minerals, siderotil, rosenite and copiapite occur variably throughout the deposit. Mineral texture is variable ranging from liberated sphalerite grains visible to the naked eye to intergrowths, particularly between sphalerite and galena, to less than ten microns. Both pyrite and marcasite are present. To date no enhanced reactivity of marcasite has been observed. For this discussion, ""pyrite"" will be used to refer to both iron sulphide minerals. In common with other sedex deposits, Red Dog contains organic and sulphur impurities."

Jan 1, 1997

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By D. M. Doyle

"In this paper I will summarized the Falconbridge Nickel Mines1) energy costs and consumption data by fuel, process, cost centre and estimate our future costs and consumption patterns 2) detail the distribution of electrical energy 3) distribution of other forms of energy 4) describe present and planned energy conservation schemes; and 5) discuss economic justification and responsibility.There is sufficient material in this presentation to warrant several technical papers, however we felt that an overview of all our data and endeavors on the subject, would be most beneficial to those companies formulating energy conservation plans. The data briefly referred to in this slide presentation can be found in the technical paper.Over a five year period, total energy costs will vary between $63 and $94 MM depending on the future rate of energy cost escalation. An unrealistic 32% reduction in energy consumption is required to hold our own in the years ahead whereas an attainable 10°;, reduction in energy consumption would save $9 MM over this five year period.Total energy consumption, tonnage of ore delivered to plants and their ration BTU’s per ton of ore, are graphed for the years 1973 through 1976 and forecasted for the 1980’s. In 1974 we along with other member companies of the Mining Association, determined our purchased energy per ton consumption rate and set, as our goal, a 20% reduction by 1980. The dotted lines calculated from the energy audit, based on 1976 data shows there is a potential for a 10% increase in energy per ton. This could result from a lower than forecasted mining rate and operation of the new roasting, electric furnace and acid recovery facilities installed for environmental considerations at designed capacity."

Jan 1, 1978

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By O. Mejia, J. Drozdiak

"This paper summarizes a comprehensive energy and cost study comparing an existing SAG mill based circuit at Huckleberry Mine with two proposed circuits involving comminution technologies which are associated with energy efficiency: high pressure grinding rolls (HPGR) and high speed stirred mills. The specific energy requirements expressed as kWh/t for the proposed circuits were determined from pilotscale HPGR and stirred mill testing conducted at the University of British Columbia. Samples and operating data were collected from Huckleberry’s copper-molybdenum concentrator to evaluate current mill performance for comparison. To support the base case, the SABC circuit was modeled using JK SimMet® software. The main comparison focused on the complete energy requirements for each circuit, including materials handling equipment such as conveyors, screens, feeders and pumps. This paper also provides capital and operating cost estimates for each of the comminution circuits. The results showed that the HPGR - ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG - ball mill circuit at the same P80 grind size of 160 µm. At a grind of 80% passing 75 µm, the HPGR - stirred mill circuit showed a 34% reduction in energy compared to the base case. It was concluded that the energy reduction for the new flowsheets significantly improved the economics of the Huckleberry comminution duty.INTRODUCTIONUp until now, tumbling mills such as AG/SAG mills and ball mills have had a dominant bearing on the design and economics of comminution circuits. However, it is commonly agreed that the majority of employed comminution processes are energy intensive and energy inefficient, accounting for up to 80% of overall process plant energy consumption and having an efficiency of as low as 1% (Abouzeid and Fuerstenau, 2009; Fuerstenau and Abouzeid, 2002). The U.S. department of energy reported that there is a potential to reduce energy consumption in the metals industry by up to 61% from current practice to bestestimated practical minimum energy consumption; suggestions included the implementation of best practices and the adoption of energy efficient mining and mineral processing technologies such as advanced blasting techniques, high pressure grinding rolls (HPGR) and stirred mills (U.S. DOE, 2007)."

Jan 1, 2013

By Christoph Mueller

Mining operations are characterized by cost pressure and cycling product prices. A high potential for enhancing efficiency is the integration of all single steps of the mining working chain into a production process structure to make advantage of an optimized flow of material and information through the ?moving ore factory?. As modern mining machinery today is controlled electronically and even already operated autonomously, a smooth and cost efficient flow of data in the mining process will be crucial for cost efficient future mine operations. Therefor, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ?common electronic language? for easy and standardized data exchange between mining machines and central computer systems. As in other industries, this standard is expected to have significant impact on the use of automated equipment. It shall provide easy ways of using multi vendor machine installations in data controlled mining processes. At the same time it reduces cost for individual development of interfaces for all parties involved. Standardized data exchange is also a crucial precondition to integrate the mining process into enterprise level modeling, cost analysis and decision finding systems. The standard?s technical architecture is open and flexible for future applications. It uses modern XML technology enabling easy data exchange with commercial databases as well as open on line networking. The IREDES work is carried out by the initiative members working jointly together in the technical work groups. Prototyping implementations of the Drill rigs profile are currently going on. Further profiles under development cover LHD?s/Loaders/Trucks and Explosives Chargers. The first official release covering the Drill Rigs profile is planned for the end of 2002.

May 1, 2002

By B. St. Pierre

"The alchemists' symbol for antimony is a diamond with a dot in the centre. The latin name ''stibium'' gives this mineral its chemical symbol ""Sb"" and the name to the principal ore containing antimony. This is Stibnite, a sulphide of antimony, and the valuable mineral at the Consolidated Durham operations. Stibnite chemically pure contains 71.69% antimony metal.Antimony is used in many forms, as an alloy in the production of metal products and as chemical compounds of oxides and sulphides. In Biblical times, antimony was used as a medicine and as eyebrow makeup.Today, the largest single use of the metal is as a hardener and strengthener of lead, and corrosion inhibitor in storage batteries. New applications for antimony in its oxide form as fire retardants are broadening the overall demand especially in the chemical, plastic and fabric industries. Other users include the Military for such things as tracer bullets, shrapnel, smoke screens and flame throwers. An unusual property of the metal is that it contracts when heated which has made it a valuable alloying metal in the printing industry, for heat shields on re-entry vehicles used in the space programmes, and also for the manufacture of bearings."

Jan 1, 1977

By Tanveer Jahir

With increasing energy costs and mounting government pressure to adopt low emission, green sources of energy, it has become imperative to develop long-term sustainable underground infrastructures that exhibit low power consumption. Underground mining environments are mandated to have ventilation systems in place to replace polluted air with clean air. Continuously running air ventilation systems have proven to be an expensive solution for this requirement. Ventilation-on-demand (VOD) is a cost effective method for not only reducing energy consumption and greenhouse gasses, but also ensuring the safety and well-being of the miners beneath the surface. VOD is achieved by monitoring the air quality in target areas of the mine, and based on variables such as the number of personnel in the area, the number of emission-emitting vehicles, the air leakage around doors and entrances, dust levels, and other key environmental details, the speed and angles of the fan blades are adjusted to increase or decrease the volume of air flow. For over 40 years, Conspec Controls has been developing systems capable of VOD through the use of controllers, gas monitors and personnel/vehicle tracking equipment, providing inexpensive, reliable solutions for underground ventilation.

May 1, 2011

Ontario Operaations Mining Garson Stobie Copper Cliff North Copper Cliff South Creighton Mcreedy East Milling Clarabelle Mill Smelting Smelter Matte Processing Anode Casting Refining Copper Cliff Nickel Refinery Port Colborne Cobalt Refinery

May 1, 2007

By R. E. McElvain

"Hydraulic transportation of solids in suspension with water or other carriers, such as oil is becoming more practical as economic situations develop with respect to the railroads and other carriers. Of significant importance, is also the increased size of the major operations and the total impact of larg- er tonnages and more critical sources of supply.There are several means of imparting energy into the solids and directing the material down a pipeline, but the centrifugal pump is emerging as the most practical piece of equipment when considering relatively large flows and recent development. We can now handle relatively high densities without interruptions. This provides the mining and transportation fields a more economical means of lifting and transporting coal and other mineral products.Equipment & MethodsWarman International has developed several methods of alternate PDP against high heads. We have, at least for the present time, shelved our pump which uses clear water to slurry method and have placed our major emphasis on the full development of the centrifugal pump. I personally see several similarities on the alternate reciprocating devices as compared with the steam piston type engine versus steam turbines. The centrifugal pump comes into its most advantageous position at about 2000 GPM and can also show advantages by means of increased mobility, when driving tunnels and in other difficult operations when considering the total economic results. We now have some interesting d<:ta on one 5 mile raw silica sand line designed for pumping at 200-400 tons per h:mr. This is a separate subject on a ""simplified approach to slurry transport"" and paper has been prepared for the Hydrotransport 5 proceedings in Germany this Spring. Reference 1 may be of interest to those who want to delve into the subject further, and I also have some advance copies of this paper."

Jan 1, 1978

By H. M. Lewis

The current status of the international zinc market is summarized, and a supply /demand outlook is presented for the next five years. A number of technical problems facing the industry are outlined. Introduction ZINC has sometimes been called the unknown metal. Considering that on a world basis it ranks third among non-ferrous metals in production and consumption, zinc retains a certain modesty. It has no distinctive colour like copper, lacks the low density of aluminum or magnesium and is not always easy to identify as a product. The &apos;spangle&apos; of galvanized steel is probably zinc&apos;s most distinguishing feature. The purpose of this article is to develop an over-all review of zinc. Starting with the current position of the metal, the major factors that will shape its future will be described so that an assessment of the outlook for zinc can be made.

Jan 1, 1978

By G. M. Hughes, J. Ellis

"IntroductionHydraulics has been considered a science for thousands of years. Applications included water wheels, dam; and slice gates but today the term ""hydraulics"" commonly refers to ""power hydraulics"" in which fluid is used under controlled pressure to do work. The mining industry employee’s hydraulics in practically every aspect of its operations, on such equipment as trucks, front end loaders, LHD units, crushers and hydrostroke feeders. The many benefits of hydraulic drives such as ease of variable speed control, high power: weight ratio low envelope size of hydraulic actuators and ease of maintenance have been extensively developed in the pulp and paper, chemical, steel, and other basic industries, but until quite recently, concentrator operators have not taken advantage of the versatile methods of power transmission offered by hydraulic systems.After some preliminary testing at the Lynn Lake concentrator Sherritt Cordon Mines Limited installed several hydraulic system; at their Fox Mine concentrator to drive slurry pumps and conveyors. The systems used at Fox and the systems which will be installed at the Ruttan concentrator are briefly described in this paper. Since acceptance is based mainly on understanding a few basic principles of hydraulics system; including pumps, motors, circuitry and central methods are also presented in the paper.PRINCIPLES OF POWER HYDRAULICSBasicsHydraulic systems provide an uncomplicated, versatile means of power transmission. The basic system is quite simple. It consists of five main elements, as shown in Figure 1, which are:1. Prime Mover - generally an electric motor.2. Hydraulic Pump - fixed or variable positive displacement type such as a piston or vane p.mp which displaces a constant amount of fluid for ead1 revolution - this unit converts mechanical energy of the prime mover into fluid energy.3. Oil Reservoir - a standard tank to operate under atmospheric pressure which has a capacity of 2 - 3 times the maximum gpm outp.it of the hydraulic pump."

Jan 1, 1972

By F. Lindroos

A cornerstone in the LKAB Green Pellet concept is to produce pellets with a small footprint in terms of energy con-sumption, CO2 emission and emission of other elements harmful to the environment, like dust, sulphur dioxides, nitrogen oxides, chloride and fluorine. The concept also encompasses our determination to make pellet products that contribute to low environmental impact and low energy consumption in our customer?s processes. The presentation will focus on the pelletizing process. It will describe both how we have attempted to decrease the generation of unwanted components in the process gas, and how we have tested or evaluated equipment for external gas cleaning. We will discuss and give examples from recent and on-going efforts and outline some of the future challenges we see, to meet our own environmental standards and also the tough demands imposed by EU and national legislation, while striving to boost production.

May 1, 2011

By R. S. Simkus, J. R. Egan

"Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant test work conducted in 1990-91 indicated that concentrate grades would be substantially improved by reducing the particle size (P,0) of the lead from 38 to 15 µm and the zinc from 45 to 24 µm.Circuit revisions involved installation of major new equipment including: two GUO kilowatt Vertimills for regrinding, a 4 metre diameter column flotation cell and a 4 metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were reassigned.IntroductionThe Sullivan ore body is a massive sulphide deposit consisting of fine grained mixtures of sulphides, sometimes inter-banded with country rock and varying widely in their content of lead, zinc, iron and silicates. Principal economic minerals are marmatite and galena. Iron is mainly present as pyrrhotite (85%), and to a lesser extent as pyrite (15%) .The orebody has been actively mined since 1923, with 1992 ore reserves estimated at 15,800,000 tonnes with an average grade of 4. 7% lead and 7. 9% zinc. Current plans call for treatment of 1,600,000 tonnes/year, (7,000 tonnes per operating day), with flotation feed grades of 5.9% lead, 10.1% zinc, and 22.0% iron."

Jan 1, 1994

By Buse Florian

This paper presents the specific features of the large-scale production and transportation systems (LSPTS), describing the main notions and characteristics of the LSPTS elements. A methodologically unitary approach of the formulation, formalization and solution of the problems regarding the planning of the LSPTS structure development is offered, based on the system description by the aggregation-decomposition method, as weil as on the complex of interreloted models for the planning optimization. The paper describes the characteristics of the complex of dynamic models for investments, utilized in solving the planning problems of the LSPTS structure development.

Oct 1, 2009

By J. P. Morris, J. T. Novak, E. A. Sarver

"A variety of reagents are utilized in coal preparation, but aside from performing their desired function relatively little is known about the behavior of these reagents within the processing circuits. Where exactly do reagents go once dosed? In this paper, we present preliminary results of partitioning studies on frother (i.e., MIBC) and collector (i.e., diesel) chemicals commonly used in coal flotation, and examine implications for water management (e.g., in closed-loop systems). Additionally, we discuss the usefulness of such data in predicting environmental transport and fate of chemicals – which is currently a top priority for industry.INTRODUCTIONThe purpose of coal preparation is to upgrade mined coal into more valuable products. Since coal is primarily used as a fuel source for electricity generation, product specifications are typically contracted to minimize unwanted constituents that detract from the overall heat value (e.g., ash and moisture) or that add to environmental pollution or other problems like corrosion at a power plant (e.g., sulfur) (Pitt & Millward, 1979). Failure to meet specifications results in a financial penalty for the coal producer (Szwilski, 1986), and thus preparation processes have evolved to simultaneously optimize recovery of valuable “clean” coal with rejection of mineral matter and moisture. In addition to advancements in equipment and circuitry, development and application of various chemical reagents has dramatically improved the performance of coal preparation processes.Contemporary preparation plants typically include multiple circuits that can be categorized by the size of particles they process: coarse, intermediate, and fine/ultra-fine (Figure 1). Coarse and intermediate circuits generally rely on size classification and gravity separations (e.g., dense-media cyclones), and do not require significant chemical reagents. However, fine and ultra-fine circuits often use froth flotation to separate coal from impurities, which requires chemical additives (Table 1). The primary additives include collectors, which coat the surface of the coal particles to render them (more) hydrophobic and thus more likely to attach to air bubbles and float; and frothers, which aid in the formation and stability of the froth that will accumulate the floated coal particles. Modifiers are also commonly added to flotation circuits to regulate pH in instances where coal or impurity characteristics may change water chemistries (Laskowski, 2001). Following flotation, coagulants and flocculants are often utilized in solid-liquid separations (i.e., dewatering or clarification) for coal products, and for tailings slurries prior to their disposal in impoundments. Coagulants function via double-layer compression1 to bring colloidal particles together, while flocculants promote bridging between the grouped colloids – and the combined result is enhanced sedimentation (Wills, 2006). Defoaming or anti-foaming agents may also be required to avoid fouling of dewatering operations."

Jan 1, 2012

By John R. Hawley

"This paper is intended as a review of the progress that has been made in the Province of Ontario in the field of acid drainage waste treatment technology.Three years ago, at the Third Annual Meeting of the Canadian Mineral Processors, we presented a paper entitled ""The Problem of Acid Mine Drainage in Ontario"". At that time I was working for the Ontario Water Resources Commission. The paper turned out to be the very beginning of the Commission's acid mine drainage control program. In the intervening three years, the Ontario Water Resources Commission has been amalgamated with other government groups and has evolved into the present Ontario Ministry of the Environment. Today the Ministry is involved in running one of the most advanced acid mine waste control programs in the world.As a part of its mining program, the Ontario Ministry of the Environment has published three major reports which deal directly and specifically with the industrial waste disposal problems that may arise at a mining operation. In order of publication, these reports are as follows:(1) ""The Problem of Acid Mine Drainage in the Province of Ontario"".This 338-page report covers all aspects of the problem of acid mine drainage and includes detailed sections on acid flow detection, acid flow chemistry and acid flow treatment.(2) ""The Use, Characteristics and Toxicity of Mine-Mill Reagents in the Province of Ontario"".This report, 244 pages in length, gives the chemistry and toxicity of nearly all of the chemicals that find common use in the Canadian mining industry. Most of the toxicity figures quoted are the result of a comprehensive bioassay program that was initiated by the Ministry."

Jan 1, 1974

By H. A. Steane

"This presentation will cover some crushing and grinding considerations in plant design and operation. There is nothing basically new in the subject matter presented here; however, the viewpoint and interpretation may be novel and some of it controversial.The presentation is based on experience gained in the metallurgical design of plants for Placer Development Limited from 1960 to the present. The plants are listed on SLIDE No. 1.These plants have conventional crushing, followed by rod mill and ball mill grinding. I would like to think that autogenous grinding plants are the answer for eliminating secondary crushing plants and reducing the capital and operating costs; however, the autogenous plants seem to have some problems of their own and I have had no experience with them.Fineness of Grinding RequiredFirst let us consider the fineness of grinding required.The fineness of grind will affect the recovery obtained, and the relationship must be determined. If the grinding is too coarse, some of the valuable mineral, either free or locked in middling grains, will not be floated. However, as grinding is probably the greatest single operating cost, we do not want to grind any finer than is justified economically.Finer grinding should not be carried beyond the point where the net smelter return for the increment saved becomes less than the added operating cost. Even this fineness will be beyond the economic limit because of the additional capital cost for the equipment needed to achieve it. These factors will be discussed in more detail later.The Bond work index is the commonest method of expressing a measure of the effort that has to be expended in grinding. It is the kilowatt-hours required to reduce a ton of rock from an infinite size to 80% passing 100 microns. The formula allows a calculation to be made for other size ranges."

Jan 1, 1976