Search Documents

By T. R. Kostecki

"Instrumented rock bolts are effective tools for assessing the reinforcement and condition of immediate roofs; however, instrumentation can have relatively high costs, which can be justified by high reliability and repeatable and representative data measurements. The instrument’s durability and operational life are of great importance, along with accuracy, applicability, and usefulness. This paper develops reliability models for three instrumentation technologies used in slotted rebar, drawing data from studies at five underground coal mines. Three case studies demonstrate instrument applicability and usefulness. Finally, two types of instrumented rock bolts are used to determine the direction of bend and maximum bending strain. RÉSUMÉ Les boulons d’ancrage instrumentés sont des outils performants qui permettent d’évaluer la consolidation et la condition des toits immédiats. L’instrumentation peut cependant se révéler très onéreuse, des coûts qui se justifient par sa fiabilité élevée ainsi que par des mesures de données reproductibles et représentatives. La durabilité de l’instrument et sa durée de vie opérationnelle sont très importantes, de même que son exactitude, son applicabilité et son utilité. En s’appuyant sur des données issues d’études menées dans cinq mines de charbon souterraines, cet article développe des modèles de fiabilité pour trois technologies d’instrumentation utilisées pour des barres d’armature nervurées. Trois études de cas démontrent l’applicabilité de l’instrument et son utilité. Enfin, deux types de boulons d’ancrage instrumentés sont utilisés pour déterminer la direction de la flexion et la contrainte de flexion maximale.INTRODUCTION Using instrumented rock bolts to monitor strain changes in a rock bolt array allows engineers to understand the per-formance and effectiveness of the rock reinforcement system and the response of the rock mass to such support; however, instrumentation remains a niche solution for solving complex ground-control problems—particularly for underground coal mines, which is where they are needed most. From 2000 to 2016, fall-of-ground fatalities still accounted for an average of approximately 30% of the total annual underground coal mine fatalities in the United States alone (United States Department of Labor, 2018). These tools would also be useful for deep hard-rock mining conditions. The main reasons for the lack of widespread use are not only cost but also accuracy, applicability, implementation procedures, intrinsic permissibility, and reliability (Peng, 2015). As a result, measurements of coal mine roof behaviour using instrumented rock bolts are quite scarce, not widely published, or inadequately presented to provide a seamless understanding of a roof’s response to support."

Jan 1, 2018

By Robert D. Brown, Robert B. Parsons

"The mining industry may have survived the October 28 federal budget relatively unscathed, but the same certainly cannot be said of the petroleum sector-and many mining men are left wondering if their industry will be the next one to be singled out for special attention, as federal and provincial governments seek additional revenues and pursue nationalistic or provincial policies.Higher taxes, higher prices, a potpourri of ""incentives"", and a -""Canadianization"" policy mark the principal features of the new National Energy Program released by the government along with Finance Minister MacEachen's budget address.This month, Tax Notes examines the federal budget. with appropriate emphasis on the National Energy Program and its possible future implications forthe Canadian resource industries.IntroductionMost of the Canadian mining industry (tar sands miners excepted) heaved a sigh of relief on the evening of October 28, 1980, as Finance Minister MacEachen confounded the prophets in his budget address by not raising personal or corporation taxes and by making only relatively modest changes in the general tax system. Instead, he concentrated on a sweeping new energy policy. Unfortunately for that important sector of Canada's mining industry which is involved in mining the country's vast tar sands reserves, either now or in the future, the National Energy Program that was introduced along with the budget 'has serious implications."

Jan 1, 1981

By W. W. Cummings

Canada's only current tungsten producer started up in 1962 with a small open-pit mine on the Flat River , 180 air miles north of Watson Lake, Yukon Territory. The orebody was in a contact-metamorphic skarn zone and contained about 1.5 million tons of ore grading an estimated 2.47% W03 and 0.5% copper. Near the end of the open pit , a new zone was discovered on the lower limb of the same structure, and the decision to go underground was made in 1972. The new "E Zone" contains over 4 million tons of ore grading an estimated 1.6% W03 and 0.28% Cu , and has been supplying the concentrator at about 175,0 00 tons/ year since late 1974. A continuing program of change and up-grading is necessary in the conversion from a seasonal open-pit mine with limited life to an underground operation with twenty years of reserves. Changes are necessary in plant and services as well as the mine. Also, environmental protection requirements have changed from rudimentary to rigorous over the life of the operation. This paper sums up the changes in the operation since 1971 and outlines the changes yet to come.

Jan 1, 1977

By B. Wasmund, B. Haneman, G. Sheehan

Success in implementing new technology for metallurgical processes is not a foregone conclusion: This paper includes a survey of 23 new technology-based metallurgical plant start-ups, in which the authors have identified 7 successes, 9 difficult start-ups, and 7 failures. Success is defined not only as meeting the schedule and budget to the end of mechanical completion; the key goal is a fast ramp up to the full design production level, with minimum plant and equipment modifications required after start-up. This paper sets out the key factors that underlie achievement of a quick production ramp up curve, as determined from the authors' project experiences and a quantitative analysis of over twenty metallurgical plant start-ups, both pyrometallurgical and hydrometallurgical. Thorough test-work and pilot plants, plus appropriate scale-up to the full commercial plant, are key determinants of success in implementing new technology in metallurgical processes. Another critical factor is the number of new elements and their interactions. Project phasing is also particularly important for new technology projects, with appropriate review after each phase to develop a risk mitigation plan for the subsequent phase. New technology projects need committed champions to advance the project in the face of sceptics, but also require dispassionate and unbiased experts to ask the hard questions. As a project evolves, it is important to periodically question the appropriateness of assumptions, as well as to re-assess the relevance and completeness of data from test-work I pilot plants I industrial analogues. Sufficient human and financial resources are required to complete the often arduous implementation phase. During the ramp-up period, the operation generates little positive cash flow; however, significant expertise and capital are required for the de-bottlenecking projects that are often necessary to reach the plant's design output level.

Jan 1, 2011

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By Robert B. Parsons

"Once all the hullabaloo about Finance Minister Wilson's April 27 budget died down (or was it an April 26 budget?), the pain of the budget papers began to sink in. Individuals and corporations will have to dig deeper and pay more taxes - and government will continue to dig deeper and spend more. The irony of the situation is that higher tax rates actually make flow-through shares more attractive as a tax-deferral investment - a bittersweet ""bravo"" for the mining industry.INTRODUCTIONFor the first time in Canadian history, a major budget address has taken two days to deliver. Of course, it's not a case of long-windedness, but rather a case of a hastily called press announcement on April 26 in response to a budget leak, followed by a formal budget speech on April 27.The general reaction of the business community to the budget was to the effect that the tax hikes are acceptable, but the government's failure to curb spending is less than acceptable. Mr. Wilson's reported response indicated that the government had never promised to cut spending, and that increased government spending would actually benefit the country. That age-old debate will doubtlessly continue for generations.In any event, three noteworthy components of the budget papers are:• Personal income tax rates increase effective July I, 1989;• A ""large corporations tax"" (in effect 'a corporate ""minimum tax"") is effective July I, 1989; and• Federal sales tax increases are effective from June 30, 1989, to be replaced by a national sales tax in 1991.A brief overview of these and other budget proposals follows."

Jan 1, 1989

"10.1. IntroductionAs discussed by Westland (1981), the six platinum-group elements (PGE) belong to the Group VIII transition metals, to which iron, nickel and cobalt also belong. The chemical similarity between these nine metals accounts for the fact that they tend to be concentrated together as a result of geological processes. These processes started to effect the distribution of these metals at the very beginning of the earth's history.The first line in Table 1 gives the concentration of nickel and certain other Group VIII transition metals in carbonaceous chondrites, those meteorites with a composition that is believed to reflect best the composition of our planetary system apart from hydrogen and helium. The second line is the estimated concentration of the same elements in the earth as a whole. It is seen that these two estimates are quite similar, the earth being perhaps 2 to 3 times richer in these particular metals than the planetary system as a whole. The reason for this is not fully understood, but it may be due to the earth being formed by the accumulation and capture of a greater proportion of iron (and therefore siderophile-rich) than stoney (and therefore siderophile-poor) planetesimals than the planetary system itself.The third line in Table 1 is the average composition of the crust of the earth. With the exception of iron, all of the Group VIII transition elements are rare in the crust, present at concentrations of It tOO to Itt ,000 of that of the bulk earth. This is because the outstanding chemical characteristic of this group of elements is their siderophile nature; that is, their tendency to alloy with metallic iron. Because of this, once the earth became molten very early in its life history, these elements dissolved in the molten iron present at this stage and were removed from the outer accessible parts as this dense liquid sank to the centre of the earth to form the core. Although iron was the main instrument of concentration of the Group VIII metals, its much greater over-all abundance and its ability to combine with oxygen more easily than the others in the group means that significant amounts still remain in the oxidized portions of the earth.The fact that most of the Group VIII metals are available to use in workable concentrations at all is that they are 5 to 30 times more concentrated in the earth's mantle than the crust, as shown in line 4 of Table I. There has been a constant, if slow, interchange of matter between the mantle and the overlying crust throughout most of the earth's history and, under certain circumstances, this interchange has given rise to economic concentrations of metals."

Jan 1, 1979

By J. J. Brummer

The possibility of diamonds occurring in Canada was first raised by W. H. Hobbs in 1899, who concluded: "that the apex of the fan of diamond distribution probably lies somewhere in the strip of the territory bordering James Bay on the east." This was based on the occurrence of diamonds in surficial sediments at various locations south of the Great Lakes. There are two recorded discoveries of drift diamonds in Ontario: (a) the Peterborough Diamond, 33 carats in size, poorly documented and found sometime before 1920;and (b) the Jarvi Diamond, 0.255 carat, found during 1971 in Sheraton Township near Timmins . Both discoveries were in surficial sediments and their source(s) have not been located. During 1960, Selco Exploration Company Ltd. started a heavy-mineral sample program of river gravels in the James Bay Lowlands of Ontario. This was continued by Canadian Rock Company Ltd. (1962-1963) and the Ontario Division of Mines (1973). The surveys discovered the presence of kimberlite minerals in gravel samples from streams draining the Moose River Basin. A total of 53 pyrope grains, four magnesian ilmenites and one grain of chrome diopside were identified from 32 sample locations. A study of the distribution of these minerals suggested the kimberlite source rocks to be located along the north margin or within the Kapuskasing gravity "high" in the area immediately south of James Bay. The Jarvi Diamond, found on an esker east of Timmins, could well have originated from this area. During 1965, an esker was sampled by the Geological Survey of Canada, and the results attracted attention to the area south of Lake Abitibi. At 9 out of 34 sites sampled along the Munro esker, Lee recorded the presence of pyrope garnets and very minor chrome diopside.

Jan 1, 1978

By J. M. Livingstone

"This paper covers some of the problems confronted by Canada's railways in moving bulk materials from their source to the dock-site. The ""cost center"" concept is presented, and hypothetical examples of its use given. Also discussed are systems design, the unit train and pipelines.INTRODUCTIONCANADA LIVES BY RER EXPORTS and the Port of Vancouver by the exports of the Mountain and Prairie Empire at her back. The most recent estimates of off-shore shipments of bulk from the Port of Vancouver rise to 35.8 million shipping tons in 1985 and deep-sea general cargo estimates, in and out, are estimated at 7.6 million shipping tons for the same year. This compares to 7.67 and 2.87 million shipping tons, respectively, in 1965."

Jan 1, 1968

By J. E. Gill

"The name 'Canadian Shield' is used for a vast area; largely in northeastern; Canada; underlain by Precambrian rocks. The part in Canada has an area; of about 1; 790; 000 square miles. Extensions in Greenland; Labrador; Newfoundland; and the United States bring the total area to around 2; 800; 000; square miles. The boundaries of the Canadian part are shown in Fig. 1.; At its margins; the Precambrian rocks can be seen at many places to; extend beneath a cover of flat-lying Palxozoic or later sediments. Information; from borings in the Plains and natural exposures in mountain-built belts; show that similar rocks form a large part of the continental platform. The; Shield; therefore; is a large exposure of what may be regarded as the foundation; of the continent."

Jan 1, 1954

By C Carbonneau

In order to successfully produce columbium pyrochlore concentrates, St. Lawrence Columbium and Metals Corporation had to face two principal problems met in several new operations but possibly made more acute than usual owing to the newness of the project. 1.-The ore is particularly complex, as it is made up of an elaborate intermingling of carbonates and discontinuous ultra-alkaline rock bodies of various ages and types in which no less than seventy mineral have been re-ported. Obvious petrographic or structural controls are lacking. Ore boundaries have to be defined on the basis of assay results and the determination of several minerals which occur in trace amounts. 2.-The pyrochlore concentrates produced had to com-ply with a set of stringent specifications. This fact, combined with the low Cb205 content of the ore, necessitated the use of a beneficiation process that would have to operate at a concentration ratio greater than 100:1. A brief description of the mill circuit is given. Mill stability was obtained through extensive mineralogical study of the mill feed coupled with close geological and engineering control of the mining operations.

Jan 1, 1965

By J. M. Rios

Without conscious effort and understanding, a number of factors peculiar to mineral exploration campaigns conspire against building sustainability in host communities. These include the episodic and transitory presence of an exploration team in the community and the inherent uncertainty of outcomes; most projects fail. Given these circumstances, there is a strong tendency to apply a simple formula of providing employment, pragmatic philanthropy and supporting infrastructure improvements (roads, schools and clinics) to demonstrate that mining provides benefits. Experience in rural native communities of Mesoamerica has shown that it is possible to create positive, sustainable outcomes quite rapidly within communities, which build capacity, improve quality of life and support a strong social license to operate. Success comes from an understanding of community structure and dynamics; engaging with all segments of the community; creating healthy, transparent and accountable relationships based on clearly defined roles and responsibilities; and supporting and strengthening the role of women in a culturally appropriate way. To this are added innovative and culturally appropriate ways of incorporating sustainability through genuine social investment in areas more typically addressed by exploration companies; health, education, and environmental management.

Aug 1, 2013

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texasgulf Incorporated, operates the Kidd Creek mine, a 10,000- tpd base metal producer, near Timmins, Ontario. Two different ore types are mined and milled copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator, the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous onstream X-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8% and zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.

Jan 1, 1973

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By Y. F. Jiang, K. Fang, Q. Q. Jiang, Q. Wu

Inter formational sliding of bedding planes between two different rock types in Badong formation is an important reason that leads to the instability and fracture of rock mass in this stratum. There are no specific research achievements on bedding planes between two different rock types in Badong formation. In order to study the shear mechanical properties of bedding planes between two different rock types. This paper using the software of particle flow code (PFC) and JRC model to establish several typical structures of different roughness coefficient of surface morphology based on the laboratory tests on silty mudstone and marlite in Badong formation. A great deal of numerical shear tests were carried out by ball production, radius expansion and servo infliction. The research results are as follows: First, shear strength of Badong formation is found to vary between that of silty mudstone and marlite isotropic planes by analyzing shear strength of the homogenous bedding planes and inhomogeneous rock types, we can find that the shearing strength in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the shearing strength of silty mudstone isotropic planes. Second, the basical friction angle of bedding planes between two different rock types in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the basical friction angle of silty mudstone between isotropic planes. Third, based on the experimental results, an expression is obtained to describe the relationship of the ratio of shearing strength between bedding planes of two different rock types and isotropic planes in soft rock, the rock combination coefficient, and the roughness coefficient. This study has important significance for further research on the shear mechanical properties of bedding planes between two different rock types.

Jan 1, 2015

By M. P. Davies

"Risk, the product of probability and consequence, is an integral part of mining. Whether evaluating exploration priorities, determining property acquisition potential, reviewing the components of an operating mine or assessing environmental/closure issues, the concept of minimizing risk is central to economic and technically appropriate decision making.Until recently, risk evaluations have tended toward a strongly mathematical basis. With this previous trend, it was essential to establish precise probability density functions to all assessed components or issues where often little information was available. The combined effect of the seemingly complex analyses with corresponding insufficient data often resulted in either a poorly executed risk evaluation or no evaluation whatsoever; either result not acceptable for optimal decision making. This paper presents a simple and practical procedure to carry out risk assessments for the mining industry. Although simplistic in nature, the power and usefulness of the technique is immense. The basis for the procedure involves combining deterministic assessments (often “gut feel”) with appropriate probabilistic descriptors. The resulting procedure, termed Potential Problem Analyses, or PPA, can be used anywhere an evaluation of risk will assist in optimizing technical and/or economic decisions. As will be shown, a key element of the PPA procedure is the multi-disciplinary input the framework allows which makes the method ideal for a teamwork approach to decision making."

Jan 1, 1997

By S. Averill, B. Schreiner, V. Sopuck

The La Ronge. Kisseynew, Glennie Lake and Flin Flon domains. the main focu for gold exploration in the southeast part of the Saskatchewan Shield, were subject to continental glacial ice advances from the northeast during the Quaternary. Based on forty-four auger hole along with surficial mapping, the general Quaternary stratigraphy in this area is observed to be composed of a lower till unit , an overlying stratified unit of glaciofluvial sand and gravel and/or a glaciolacustrine silt-clay unit. an upper till. and an upper tratified unit. The lower till is commonly found throughout the geological domains except where it has been eroded in glaciofluvial or fluvial channels. Glacial Lake Agassiz fo rmerly covered most of these prospective domains. The lacustrine deposits associated with the lake impede surficial geochemical surveys including soil. lake sediment. and biogeochemical surveys. The approximate extent of clay cover can be predicted from beach elevations. For instance. in the Waddy Lake area. clay i not known to occur above about 1,400 feet (425 m) elevation. Exploration techniques are hampered by clay in at least one third of the volcanic belt. Thi s influence is indicated by the fact that nearly all gold prospect found to date are located above 1,400 feet (425 m) while the area of clay cover is vi rtually unexplored. The upper till i related to a minor ice readvance. This till is the medium often sampled during soil surveys in the area . lts value as a geochemical ampling medium is dependent on the extent of erosional contact with bedrock highs on the lower till. Those areas which are relatively free of lacustrine and fluvial deposits are those where surface geochemical methods work best. In the Waddy Lake volcanic belt approximately 25-50% of the area may be suitable for surficial surveys. The area of the Star Lake prospect occurs above the 1,500 foot (460 m) elevation and was not covered by Lake Agas iz. The effectivene of till sampling as a surface sampling medium was tested in those areas above the clay level. Till orientat ion surveys were carried out at the Star Lake property and the Tower Lake prospect (Waddy Lake area) within the La Ronge Domain . Gold grain counts and analy es of heavy mineral concent rate from 7 kg surface ti ll samples were used to delineate dispersion trains down-ice from mineralization. In addition, the clay fraction and a 30 g (-80 mesh) subsample from the same till sample, were analyzed for gold . In the Star Lake area, ice direction is subparallel to the strike of several narrow northeast trending auriferous structures. arrow dispersion trains down-ice from known

Jan 1, 1986

Once applied, EarthZyme reduces the tendency for a road to exhibit common maintenance issues: wash-boarding, rutting, heaving, potholing and dust.

Aug 1, 2013

By M. Vallée, J. -P. Charette, D. P. Gold

"The Oka Carbonatite and Alkaline Complex is a Lower Cretaceous intrusive body of the Monteregian petrographic province. Carbonate rocks of various types, and associated alkaline rocks of the ijolite and okaite suites, are distributed in a double ring-dyke structure 4 Yi miles long by 1 1/2 miles across. Alnoite and alrioite breccia pipes intrude all rocks of the Complex and indicate, from inclusions, that a cover of Palaeozoic rocks existed at the time of emplacement.The results of radiometric, magnetic and gravity surveys of the Complex are compiled and discussed both with respect to the regional pattern and, locally, the bed-rock geology. The Complex is characterized by high-intensity anomalies.Exploration activities started during 1953, and mining operations began in 1961 on the property of St. Lawrence Columbium and Metals Corporation, at one time the world's largest producer of niobium concentrates. Because of the boudinaged and fractured nature of many of the rocks and the variability in grade of the ore minerals, the role of the mining geologist is both demanding and exacting. Rock types are varied and their mutual relation-ships ambiguous, the minerals are rare and complex, and close geological control of the ore is needed in the mine and in the mill. Closely spaced diamond drill holes are needed for mining control, and the ore-waste contact is defined mainly by assay results.In the exploration for 'carbonatites' in Eastern Canada, aeromagnetic surveys are judged to be the best exploration tool, followed in decreasing order by the search for circular structures on aerial photographs, regional gravity surveys and radiometric surveys."

Jan 1, 1967

By E. B. Wilson

"Although the Operations Research technique of Reliability Theory has been applied with marked success in many fields, including the Apollo spaceship programs, the concept of reliability has not been generally adopted in mining and other heavy industries. Of course, reliability, or the probability that a system will be able to operate without a failure for a given interval of time, does not require the same emphasis in mining as in the aerospace industries. Nevertheless, certain aspects of Reliability Theory can be followed advantageously. For example, reliability calculations can determine the best time to overhaul and whether to retain stand-by units.The usefulness of the pseudo-operations research technique known as Replacement Theory is more readily re-cognized by the maintenance engineers in mining and other heavy industries. One of the least complex models enables the optimum Lifetime of an asset to be determined."

Jan 1, 1970