Search Documents

By D. S. Case

"Following a brief explanation of the land arrangements under the Alaska Native Claims Settlement Act, this paper will examine both a mineral exploration agreement and a mining development agreement negotiated between two large mining companies and two different Alaska Native institutions. One of the institutions is a village corporation involved with an exploration agreement and the other is one of the Alaska Native regional corporations, which is party to a mining and development agreement with Cominco Alaska for the development of the Red Dog lead and zinc mine.Special attention will be given to the factors to be considered when dealing with small aboriginal owners with few resources in the context of an exploration agreement, including development issues which must be considered early in the process. The paper will also discuss the unique royalty and taxation structures developed for the Red Dog Mine Agreement as well as environmental issues. The paper will also consider the ways in which the cultural and differing economic interests of an aboriginal owner and a large mining company have been accommodated in the both the exploration and development agreements"

Jan 1, 1998

By A. L. Mular

"IntroductionThe mining industry has made slow but steady progress toward the automation of mineral processing plants over the last 35 years. The stimulus to automate is associated with important economic and hidden benefits, so that today, the latest in instrumentation and technology is being employed.This chapter assesses the status of instrumentation justified economically, defines levels of control and certain fundamentals of feedback control loops, describes typical sensors employed in concentrator circuits, summarizes control strategies employed therein, and briefly highlights trends in integrated plant control.Current Status of AutomationAs early as 1948, the mining industry began to show interest in automation, probably because of its close association with the petroleum industry. By 1958, some regulatory control had been achieved in various sections of a concentrator, particularly in crushing circuits. Successes were attributed primarily to the reliability of sensors employed in the corresponding control scheme. By 1961, computers had appeared on the scene, initially, for data logging purposes.From 1958 to 1965, very few new control strategies had been implemented. Guidelines in vogue at this time appeared to be:- Install proven automation, unless a good instrumentation department exists at the concentrator.- Do not bite off too much instrumentation at one time.- Do not purchase on price alone; instrumentation must function in the concentrator environment.- Do not purchase automatic control equipment to be fashionable.Such guidelines were employed1 because of a lack of: (a) quantitative process knowledge, (b) reliable primary sensors, (c) initiative to try something new, (d) trained personnel, and (e) understanding that older concentrators could justify automation in many situations."

Jan 1, 1989

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By Jom Kresta

Fundamental changes in the Bitumen Production process at Syncrude have led to the integration of Mining and Extraction operations. Successful operation of the integrated process requires the coordinated effort of several business units. Hence, decision-making has become increasingly more complex and better tools are required. IO2 is a collaborative effort to develop a proof-of-concept prototype of a distributed decision-support system for integrated short-term production and maintenance planning with fleet allocation and dispatching. The prototype includes three main modules (planning, dispatch, and maintenance), a shared database, and a simulation module. At this stage, this prototype is used to plan and operate a simulated mining operation. It is used to demonstrate the viability of the chosen systems architecture and algorithms, as well as the information flows and interactions necessary for improving the overall performance of the integrated operation. While the problem is demonstrated using Syncrude?s site, the methodology is applicable to most integrated resource allocation problems.

May 1, 2002

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002

By B. K. Gorain

"As mining has evolved over a century, so are the challenges associated with mining. Mining of complex ore bodies at greater depths is a major challenge requiring high capital and operating costs due to remote locations, high energy costs, water quality and complex environmental issues. In addition, the stakeholder expectations are growing along with challenges associated with highly complex mine permitting processes and changing demographics of mining jurisdictions. The dynamic metals market adds to these challenges impacting the long term development and sustainability of mining projects.These challenges are compelling mining companies to look at various innovations with an integrated approach focusing on meeting the needs of various stakeholders. Mining companies are slowly tapping into some successful concepts that have transformed other industries such as manufacturing, chemical, pharmaceuticals along with oil and gas.This paper provides an overview of various innovations and technology developments in mineral processing that have shaped the current mining industry. A glimpse of the present and future challenges in mining is also presented. An integrated approach to problem solving involving various stakeholders is gaining momentum and this has been reflected in this paper. Various developments that are being pursed in mineral processing focusing on a change in the existing mining paradigm are also presented in this paper.INTRODUCTIONAs mining is evolving, so are the challenges associated with mining. Some of the key challenges are complex ore bodies at greater depths, high capital and operating costs, water scarcity and quality issues, high energy costs, complex environmental issues including tailings management, worldwide constraints on resource availability, more and more elaborated regulations in emerging economies impacting the permitting processes, increasing stakeholder expectations, changing demographics of mining operations with ever-changing cultural or community expectations and the urgent need for a better assessment of project viability, this in very dynamic metals markets impacting the dynamics of mining projects development and sustainability."

Jan 1, 2016

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By C. I. Garcia, G. Zhou, W. Gao, A. J. DeArdo

The development of X-100 and X-120 linepipe steels was investigated using a series of low-carbon Mo-Nb-B steels. The laboratory steels were vacuum melted and processed using advanced thermomechanical processing (TMP) philosophies. Prior to the laboratory hot-rolling experiments, the grain coarsening temperature, the conventional T95 and T5 start-stop recrystallization temperatures and the transformation behavior of y were studied using a computer-controlled high temperature deformation MTS-458 and a Theta-IV High Speed dilatometer systems. The results from these experiments provided the guidelines for the design of the laboratory hot-rolling TMP processing experiments. The mechanical properties of the experimental steels showed yield strengths in the range 700-850 MPa and CVN impact properties of over 80 J at -20°C. The best balance of mechanical properties was obtained by using CCR+DQ+Tempering treatments. The major microstructural features responsible for the observed mechanical properties in order of importance were: a) substructural refinement associated with lower bainite, b) dislocation strengthening, c) fine recrystallized ferrite, and d) small amounts of retained austenite. Fine Nb(C,N) precipitates formed in ferrite were observed, however their contribution to the strength was minimum. Most of the Nb(C,N) precipitation took place in austenite. This precipitation was used to exert microstructural control of austenite during hot rolling. The physical metallurgy and optimum TMP to achieve the mechanical properties are detailed in this paper.

Jan 1, 2005

By K. Morin

"Silver and gold leaching by cyanidation is a well-known process used around the world. This reaction is often accompanied by the leaching of other species throughtout the cyanidation circuit that causes the diversion of cyanide towards non valuable by-products (SCN-, Cu(CN)x, Fe(CN)x, etc.). One of the detrimental impacts of the formation of these by-products is the precipitation of silver-cyanide complexes that occurs when cyanide concentration is too low. Without any extra-addition of free cyanide, the precipitated silver is lost and cannot be recovered causing an important economic loss. To overcome silver precipitation, cyanidation circuits are often operated at higher cyanide concentrations. Recently, COREM’s research team has been working on a technology to measure and control silver precipitation during the cyanidation process. Moreover, a methodology has been elaborated in order to evaluate threshold cyanide level which corresponds to the cyanide concentration at which silver starts to precipitate. This technology has been tested on site on a real cyanidation circuit at Agnico Eagle’s LaRonde mine."

Jan 1, 2014

By Euler De Souza

Backfilling in Canadian mines has been practised for close to 100 years and evidence anticipates the application of mine fill technology at an increasing rate during the foreseeable future. The evolution of backfill technology is closely related to the advancement of modern mining methods and the development of new backfill technology continues to evolve. The authors, after conducting extensive surveys of backfill practices in underground mines across Canada, have concluded that, because backfill operations employ large quantities of cement and experience large costs associated both with backfilling practice and cement use, opportunities exist for reducing backfill energy costs and enhancing the application of alternative cementing agents in backfill. Consequently, the authors have developed an alternate, equally effective and lower cost binder agent replacement for cement, and incorporated waste glass into the development of a lower cost backfill (glassfill). This paper presents the results of two design stages associated with the development of glassfill: strength development and flow performance. The advancement of this technology has reached a stage that should promote industrial implementation within the Canadian mining industry. A number of Canadian mining operations exhibit potential for plant optimization through possible binder source replacement, and might thus realize associated reductions in backfill and energy costs.

Apr 1, 2005

By Nathan P. Schmidt

Climate and hydrology data are required during all phases of mining projects, including impact assessment, mine planning and design, operational water management and mine closure and reclamation design. In the Canadian north, data sources are spatially sparse and often short-term in nature, and design parameters are often estimated based on data collected at sites far distant. Confidence in such data can be increased by verification or modification using data collected during properly implemented baseline and operational monitoring programs. A data set that accurately reflects conditions at the project is more readily accepted by regulatory agencies during the permitting process, and allows development of more effective and economic water management, mitigation measures and compensation. Data requirements and collection methods for developing an adequate data set for mine development are reviewed. These are illustrated using examples from oil sands, diamond and metal mines in the Canadian north.

May 1, 2004

By V. S. Sastri, Elboujdaini. M.

"Economics of wear in mining industry and methods by which wear cost may be reduced will be discussed.IntroductionCanada loses more than $5 billion annually due to friction and wear (Table 1). It is estimated that about $1.3 billion, or about 25% of the losses, could be saved through better application of existing technology (Table 2). It should be noted that the costs given in Table 1 and 2 refer to 1986. The losses due to friction and wear and the savings would be much higher in 1996. Tribology combines the many branches and specialties in science and technology concerned with understanding and combatting friction and wear. Specifically, tribology is concerned with the design and manufacture of sliding and rolling bearings, piston rings, gears, cutting tools and other devices in which surfaces interact, in sliding or other relative motion. Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of the surfaces with the lubricants, with the chemistry, physics and use of lubricants. It is concerned with the reduction of friction and wear and the avoidance of associated failures in machinery. Similar tribological components such as bearings are used in different technologies and similar tribological problems such as abrasive wear occur in different industries. Thus, tribology is in itself a generic science and technology, concerned with the generation and dissemination of knowledge on friction, wear and lubrication, and the application of the knowledge, to a wide range of industrial products and equipment, from ploughs to space equipment, from prosthesis to engines, from washing machines to railways, from computers to power stations, from paper mills to mines. Avoidable losses due to friction and"

Jan 1, 1997

By Ron Light, Doug Applett

"HistoryThe Nanisivik mine began operation in October 1976 as the world's most northerly metal mine and the first permanent industrial project in the Canadian High Arctic. Located 700 km north of the Arctic Circle on Baffin Island's Strathcona Sound, exploration by Texasgulf Inc. between 1957 and 1970 had outlined the ore deposit. In 1974, Nanisivik Mines Ltd. was formed with Mineral Resources International, the Government of Canada, Metallgesellschaft and Billiton being shareholders, and Strathcona Mineral Services Ltd. providing project management. In 1996, Breakwater Resources purchased the mine from Alberta Energy Corporation Limited which had recently acquired the assets of then owners Conwest Exploration Ltd.Ore DepositThe main ore deposit is very flat, approximately 80 m in width and varying in thickness from 3 m to 16 m. The length of the deposit is approximately 3000 m with satellite zones located on the perimeter of the main zone. The economic mineralization is sphalerite with minor galena and silver. The sphalerite and galena are coarse grained and associated with pyrite as the main gangue component with minor inclusions pf dolomite and calcite within the deposit. The deposit being hosted in a permafi·ost environment creates a number of challenges. Dry drilling is employed in room and pillar production drilling. The permafrost aids in the stability of both the pillars and the back."

Jan 1, 2000

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

In this project, low grade copper ore samples were obtained from two mining sites in the US, and they were chalcopyrite-rich (sample A) and conichalcite-rich (sample B) ore. Copper grades were 0.6% and 0.4% for the two samples, A and B, respectively. Leaching experiments were conducted by bottle roll tests for 24 hours, and various lixiviant systems were applied. Methanesulfonic acid (MSA) and glycine were used as alternative lixiviants to sulfuric acid. Oxidants including ferric ion and hydrogen peroxide were tested. The results showed the copper extraction of sample A increased after adding 1 g/L ferric ion in sulfuric acid and MSA solution, from 20% to 36%, but further increase was not observed with higher ferric ion concentration. The copper recovery increased significantly with H2O2 concentration, and over 80% copper recovery was obtained with 10% H2O2. For sample B, the copper dissolution kinetics were relatively fast and reached the maximum value in five hours. Around 60% copper were extracted in sulfuric acid and MSA solution. Copper recovery slightly increased after adding ferric ion and H2O2. Glycine is a weaker lixiviant for both samples, the copper extractions were 36% and 4% respectively. INTRODUCTION Chalcopyrite is the most abundant copper sulfide mineral on earth, and it is one of the most refractory copper minerals regarding chemical processing. The declining copper grade and depletion of copper oxide deposits stimulate the development of hydrometallurgical process to extract copper from chalcopyrite. The dissolution of chalcopyrite by ferric ion is normally illustrated as Equation (1) and (2) (Dutrizac & MacDonald, 1974): CuFeS2 + 4Fe3+ → Cu2+ + 5Fe2+ + 2S0 (1) CuFeS2 + 4Fe3+ + 3O2 + 2H2O → Cu2+ + 5Fe2+ + 2H2SO4 (2) However, slow kinetics are usually observed from chalcopyrite leaching at ambient temperature and pressure. Researchers attribute the slow kinetics to passivation during chalcopyrite dissolution, and different passivation products are also proposed (Klauber, 2008). In recent years, many efforts have made to develop new methods to extract copper from chalcopyrite, such as utilizing bacteria or stronger oxidant (Zhao et al., 2015; Ruiz-Sánchez & Lapidus, 2017).

Jan 1, 2019

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By Mika Muinonen

"Dewatering of nickel concentrate at the INCO Thompson integrated mine-metallurgical site takes place within the smelter plant. The eight original 60 foot diameter cable torque thickeners of which four were operational and eight Dorrco internal drum filters have been replaced with a single Outokumpu high rate thickener and a single Lasta pressure filter. The modernization has resulted in a filter cake which has a more stable and lower moisture content. Control of the entire dewatering process has been improved and costs have been reduced.Typical filter cake produced from the Dorrco filters during processing of high tonnages of Birchtree mine ore was ~20% moisture vs. ~13% moisture for concentrate produced from the Thompson mine ore. The high moistures were correlated with the amount of fine magnesium silicate gangue in the concentrate. As Birchtree ore processing rates have increased, this filter cake moisture became unacceptable because of material handling problems and the impact on furnace metallurgy. The Dorrco filters were replaced with the Lasta filter in 2003 that has consistently produced filter cake at ~11% moisture.This paper summarizes the piloting, design, installation and commissioning of the modernized dewatering circuit.INTRODUCTIONThe Thompson integrated nickel processing facility was built in 1958 and originally consisted of a mine-mill-smelter and, soon after, a refinery.Nickel concentrate is pumped from the mill as a dilute slurry directly to the smelter facility ~200 meters along an unheated pipe trestle. Originally, nickel concentrate was de-watered using up to 8 conventional 60-foot diameter thickeners and 8 internal vacuum drum filters."

Jan 1, 2006

By M. Kalin

"SUMMARYWaste management in general, and the water treatment of mine and mill effluents, has become an ever increasing burden for mining operations. A reduction in these expenditures would undoubtedly be desirable if this could in fact be achieved within effluent guidelines and monitoring requirements.A brief summary is presented of the research which has as its aim the development of methods which would reduce such costs and lead to solutions for environmentally acceptable close-out conditions for acid generating mine waters. The basic concepts of Ecological Engineering and Biological Polishing are presented, together with an indication of the present state of these research efforts. Details are provided of the progress of various experiments which aim to promote reducing conditions, organic matter production and the establishment of biological filters which remove metals from the water which are then retained within the waste management areas. These conditions should lead to a curtailment of acid drainage and an improvement in effluent quality.A description is provided of the first pilot demonstration using this approach to achieve a walk-away condition for the close-out of a massive sulphide tailings resulting from 10 years of operating a copper/zinc concentrator in Northern Ontario.1.0 INTRODUCTION1.1 Waste management and close-outIt is recognized that the achievement of a cost-effective and competitive mining operation, from the commencement of exploration for ore bodies through to the day-to-day efficient operation of the mine, requires a certain expertise and sophistication. However, the environmental effects of these activities are considered peripheral issues and their importance as an integral part of the planning and development of the mine/mill, is not always appreciated."

Jan 1, 1988

By F. Hassani

This Paper describes a sudden spill of rock waste used for backfilling from a waste pass at one of the underground mine in Canada thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in future. The investigators from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied and appropriate measurements were taken and samples of the waste material was collected for further test and analysis. The field visit and the interview of the witnesses allowed a detail documentation of the events. The sequences of events related to the incident together with the experimental results obtained in the course of the investigation is detailed. The waste material was characterised in the laboratory with regard to its behaviour in the presence of water. This information is then discussed and the failure mechanism involved in this accident is identified. The full recommendation as well as the immediate operational measures implemented by the mine to prevent future occurrence of such events are discussed and presented.

May 1, 2003

By Robert Keyes, Charle Knowles, Glenn Kendall, Gary Fletcher

"The metal mining industry in Canada has been dramatically affected by the changes that have occurred in the world mineral market place. World economic restructuring in the post ""oil shock"" period of the mid-1970s, greatly increased competition from suppliers in the developing countries, and commodity price and currency pressures have all combined to severely test Canadian competitiveness. In the new mining world, the rate of growth of demand for metals has declined due to product downsizing, materials substitution, and a relatively slower growth of over-all world economic activity.The interplay of market and political factors is complex. Canadian metal mining companies must compete in world markets against low-cost producers in developing nations whose priorities often appear to be centred on maximizing foreign exchange earnings to foster development goals and debt repayment. Many of these countries have high levels of government intervention in their mining industries. The result is a greatly in-creased number of suppliers all vying for a share of a world demand growing at a relatively slower rate than in the past. To be able to compete under these circumstances, Canadian companies have had to undertake 'survival mode' measures and look to new ways of doing things. In order to identify the effects that the recent market and economic trends have had on the Canadian metal mining industry, a study was undertaken by Canada Employment and Immigration to assess these changes and their implications for the metal mining workforce.The Canadian Occupational Projection System (COPS)—Sector Study Group with the cooperation of the Mining Association of Canada, undertook a human resource survey to gather current employment and occupation information. This formed an important part of the Canadian Occupational Projection System Metal Mining Sector Study. This article addresses the with survey results, a C.E.I.C. worker mobility study, and trends and issues that are changing the mix of jobs and the way they are being done.Figure 1 shows metal mining employment for the period from 1974 to 1984. It provides a clear picture of the employment swings that the industry has experienced especially during the recession period of 1981 to 1983. From 1981 to 1983, employment dropped by 14 000, from 68 000 to 54 764, and then dropped to its lowest point in 1984 of 52 783. We feel that employment in the medium term will be flat with growth in gold mines being largely offset by continued workforce rationalizing in other sectors.Perhaps the key point is that equivalent levels of output have been achieved in the recent period (1981-1984) with a workforce that is 25% smaller than it was in 1974. This also raises the questions which the COPS/MAC survey and COPS mobility study sought to clarify, namely, what jobs have been cut and where have these people gone? Equally important are the questions of occupational skill level changes, and what types of jobs are declining and which ones are becoming increasingly important, as economic and technological changes have altered the mining work place."

Jan 1, 1987