Search Documents

By D. F. Zhang, X. Q. Jiang, N. Tahreen, D. L. Chen, F. S. Pan, D. Y. Li

Alloying with rare-earth elements has been proven to be an important tool for magnesium to achieve superior properties via texture randomization. The role of yttrium in texture weakening and the link between texture and formability are fairly well known. Since annealing is a vital part of metal processing which could significantly contribute to ductility, it is important to ascertain the impact of annealing in terms of texture change. Also, an understanding about texture development during pre- and post-deformation annealing is essential to improve the industrial deformation processing as texture is closely related to formability. While there is independent information in the literature regarding the effect of rare-earth addition and heat treatment on the texture formation, no systematic studies have been reported on the collective impact of yttrium addition, annealing and deformation on texture evolution. The present study was, therefore, aimed to identify the inter-relationship among texture evolution, yttrium content, heat treatment and deformation behavior in an extruded Mg-Zn-Mn-Y alloy. Annealing at 450°C for 1 hour and uniaxial compression tests at a certain amount of deformation were performed. The deformed and annealed samples were then subjected to annealing and compression test, respectively, followed by texture measurements. It was observed that yttrium addition effectively weakened the crystallographic texture in all conditions, which was evident from the changes in the microstructures and textures.

Jan 1, 2015

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"Abstract - The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By Marko Lampi, Ross Andrews, Jouni Pihlasalo, Robert Matusewicz

With widespread discussion on reducing carbon, sulphur and other emissions, use of sustainable energy sources and the pivotal circular economy theme, consideration needs to be given to pyrometallurgical operations broadly and more specifically, non-ferrous metallurgy. These themes present a number of challenges in terms of current operations and the view of processing the metals which are largely taken for granted in day to day living. This paper considers how these themes will impact pyrometallurgical flowsheets using the non-ferrous base metals as an example. It will examine the flowsheet chain to offer views on the boundaries of flowsheet optimization and the application of available tools to meet these future goals and challenges. INTRODUCTION The themes of reducing footprint through lowered CO2, S and other emissions, together with process sustainability (e.g. lowered energy) and links to the circular economy are well known to everyone in the metals industries. Whether it is reducing greenhouse gas emissions or analysing the importance of metals recycling in the circular economy, all these themes carry with them the fundamental premise of any change being considered; how can you best optimize a system to meet your aims? Of course, this depends on the available tools and the approach used for optimisation.

Jan 1, 2019

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallisation and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. In an expansion or a new project, a large component of the capital cost can be associated with the pressure leach step and process engineers frequently look for opportunities to mitigate costs. This paper examines a new route for increasing the capacity of an exothermic pressure oxidation leach for sulphide concentrates, sulphide and phosphide mattes and alloys.

Jan 1, 2004

By M. Takebayashi, K. Takenaka, S. Matsubara, T. Yoneyama

The cathode production of Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. reached 450,000 tons per year in 2016 with three tank houses. Niihama tank house commenced operations in 1919 with conventional sheet cathode technology. Approximately 100 years of operation experience and the technical development enabled that the current density of Niihama tank house and the Toyo tank house #1 increased to 320 A/m2. These operation techniques were utilized at the Toyo tank house #2 which started in 2005, and its current density reached up to 350 A/m2 with permanent cathode technology. In order to achieve high current efficiency under condition of 350 A/m2 operation at Toyo tank house #2, continued efforts had been made to verticality of anodes and permanent cathodes. To improve verticality of anodes and cathodes, reduction of short circuit ratio by changing the shape of the anode, optimizing the anode pressing machine and off-line process for rectifying the distortion of permanent cathodes was carried out. In addition, concentration control of electrolyte and expansion of Ni removing ability from the electrolyte prevented passivation. Finally, more than 96% of the current efficiency was stably confirmed. INTRODUCTION Today, Toyo Smelter and Refinery of Sumitomo Metal Mining operates three tank houses in Japan, namely, Toyo tank house #1, Toyo tank house #2, and Niihama tank house with a total capacity of 450,000 metric tons of copper cathodes. Figure 1 shows the trend of cathode copper production and the current density at three tank houses over the last 10 years. Cathode production by Toyo Smelter and Refinery reached 450,000 tons per year in 2016 with three tank houses.

Jan 1, 2019

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By T. G. Carter

"Tremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems, with amongst the most advanced of the tools focusing on evaluating engineered openings within Synthetic Rock Masses. These new codes have the potential to allow much more realistic design, but they must not be used without careful calibration – prior to – during and – post completion of any modelling. This paper explores some of the pitfalls of inadequate data collection and suggests more emphasis be given to calibration. Guidelines for minimum levels of parameter data are suggested for improving application of basic to sophisticated modelling codes.INTRODUCTION & BACKGROUNDTremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems. The degree of sophistication now possible with some of the available codes allows one to tackle extremely complex problems that were not thought tractable even a decade ago. Indeed, generation of synthetic numerical rock masses, based on discrete fracture network representations that closely mimic actual rock mass conditions, such as are shown in Figure 1, is today relatively straightforward, and not as user-challenging as employing state-of-the-art codes of even a few decades ago. This is largely because major improvements in computer graphics and in availability of ready-made user-friendly input-output interfaces have paralleled development of these new codes, now in some cases outpacing actual new analytical/procedure developments. This is something of a reversal from the first few decades of DOS-based rock engineering computational experience, when only rudimentary graphics were available and user-friendly input-output interfaces were virtually non-existent."

Jan 1, 2015

By J B. McConnell

The Thompson smelter has three unique features which form the basis ~f its design: fluid bed roasters which treat nickel concentrate filter cake from the mill, as well as the flux, in order to achieve partial desulphurization; the use of electric furnaces for the smelting of the partially desulphurized, preheated roaster product; and the disposal of slag by water granulation and slag slurry pumping. The installation consists of three fluid bed roasters, each feeding an electric furnace. Nickel concentrate is received at the smelter via pipe line. It is thickened and filtered, and the filter cake, together with siliceous flux, is fed through rotary bin feeders and reciprocating double-gate seals into the fluid bed roasters. Air injected into the roasters through club-head tuyeres oxidizes part of the sulphur and associated iron in the concentrate. The heat of reaction dries and heats the charge. Roaster product is recovered from the gas stream in cyclones and from the roaster bed through automatic valves.

Jan 1, 1963

By D. D. Bell

This paper presents the history of uranium procurement and demand, and takes a look at future requirements. The three basic conclusions drawn are: (1) the productive capacity of former and existing producers whose operations may be profitably reactivated is insufficient to meet demand projected beyond 1975; (2) reserves in the $5 -$10 price range do not provide the flexibility to sustain production at the high rates required in the late 1970's; and (3) only higher prices can overcome these deficiencies, as this would provide sufficient inducement for the industry to explore for and develop new reserves and productive capacity.

Jan 1, 1967

By Peter Moser, Thoma Oberndorfer

"Within the research project “Mine Development” (Fettweis and Moser, 1990) a PC-based mine database has been built up since 1991 and so far includes detailed technical and economic data of about 150 under-ground hardrock mines in industrialized countries worldwide. These data represent about 50% of the underground hardrock mines in west and central Europe, Scandinavia, United States, Canada and Australia (Fig. 1). The mining operations included in the database have been visited directly and analyzed with respect to their deposit conditions, their general design and layout and also their operational and economic performance.The main aim of the Mine Database is to make a contribution to an improved planning of new underground hardrock mines. An analysis of current mine planning practices shows, that both personnel and company experience is still a dominant factor in planning new underground hardrock operations. Through the information included in the Mine Database the experience of a single per-son or company is supplemented by the experience of a wider group of people. The Mine Database makes the huge amount of experience that is available worldwide in the field of under-ground mining accessible for new mining projects. From that a contribution to a more reliable mine planning procedure based on the performance of existing mining operations is expected.In addition to its use in planning new mining operations, the Mine Database can con-tribute to the exchange of technical data among different mining operations, especially on equipment performance, etc. Such an information service is offered by the Department of Mining Engineering & Mineral Economics in Leoben and is already being used by different mining companies. To respect proprietory information, company specific information is not released under any circumstances.The cost of building up the Mine Database, so far, is about US$500.000 — two thirds of which is labour, and one third, travel."

Jan 1, 1996

By Emmanuel Henry

Hanging wall deformation monitoring at the Kiruna Mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening towards the Kiruna Town. In the quest for more effective monitoring techniques, LKAB decided to evaluate satellite-borne Synthetic Aperture Radar (SAR) interferometry?s ability to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the Mining industry. This paper describes how subsidence is actually monitored on the Kiruna Mine?s hanging wall and gives an insight on SAR interferometry?s principle. The encouraging results are discussed as well as the technique?s benefits (continuous deformation mapping, low cost, fast, etc) and limitations (sensitivity to snow and vegetation cover).

May 1, 2003

By Catharine E. G. Farrow, David H. Watkinson

The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix,through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfdeminerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typifed by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE -Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profles fatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rhalmost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrother-mal cells may have formed in the Footwall Breccia along pre-existing structures or sulfde concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued out-ward into the footwall where they were deposited as Cu-rich footwall veins. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

Abstract-The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix, through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfide minerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typified by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE - Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profiles flatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rh almost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrothermal cells may have formed in the Footwall Breccia along pre-existing structures or sulfide concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued outward into the footwall where they were deposited as Cu-rich footwall veins.

Jan 1, 1996

By C. Caballero, K. Itagaki, P. Morales, A. Moyano, J. Font

Codelco-Chile is considering different processing options for the new projected concentrate from the Alejandro Hales mine. This concentrate is featured by its high arsenic content of up to 6%. Thus, it is important for Codelco Norte Smelter to define the technical feasibility for processing this high-arsenic bearing concentrate in its main smelting unit as it is the Teniente Converter, which beside of its dual feeding system can enhance the arsenic removal by volatilization. The present paper which is a part of an extensive research work will focus in the performed industrial scale test for processing about 7,000 tonnes of a high-arsenic bearing concentrates in the Teniente Converter at the processing rate of about 2,300 tpd. The impact on the chemical quality of the produced high grade matte will be discussed, and the effect of the As removal by increasing the Teniente Converter processing rate of concentrates up to 3,000 tpd when producing 70% Cu in the white metal will also be addressed.

Jan 1, 2007

By D. N. Madge

The use and development of industrial process control computers in the mineral industry during the 1970&apos;s has been sluggish. This cautious approach is due to lack of commitment by senior management. The lack of commitment is due to several reasons: variable mineral processes and technologies, market fluctuations, and excessive costs and inadequacies of applicable products supplied by computer vendors.

Jan 1, 1979

By B. C. Legg, G. L. Tiley

"Many of the ore bodies presently being developed are in remote locations and are, or will be, served by electrical power supply systems of limited capacity.The largest single components of the electrical systems of an underground mine are usually the production hoist drives; the power demands of these drives vary continuously throughout each hoisting cycle.Before 1970mine hoists were driven by either wound rotor induction motors or DC motors in conjunction with motor generator sets.Static Power conversion equipment now costs less to purchase and install and is claimed to be more efficient than motor generator sets. On the debit side, however, it can adversely affect the hoist motors, it operates at relatively low power factors, and it produces harmonic currents.This pa per discusses the effects of static equipment on both DC motors and AC power systems, and evaluates the relative consumption of the three classes of drives."

Jan 1, 1993

By D. A. Karvonen

In 1970, the Government of Saskatchewan instituted a program aimed at resolving the dilemma of excess productive capacity over the market demand which existed for potash produced in Saskatchewan. The two primary elements of the program were prorationing of potash production to market demand and a minimum selling price. The paper reviews the factors, both local and international in nature that led to the introduction of the program. The licensing mechanics and the operation of the program, along with the changes that have been introduced in two and one-half years of operation, are discussed. Attention is given to the results of the controls as they affect the industry and the province. Also discussed is the outlook for Saskatchewan potash in world markets.

Jan 1, 1973

By Richard Simon

This paper presents an ongoing study on the use of borehole breakouts to estimate in situ stresses at depth in a Canadian underground mine. Breakouts were identified using an acoustic televiewer (ATV) probe. Rock samples were tested in a laboratory to determine their failure curve. Breakout analyses were performed using a 2D failure criterion and a multiaxial failure criterion. Analyses were carried out using both short-term (peak) and long-term strengths (the latter considered here as being represented by the damage initiation threshold DIT). The analyses have shown that the use of the longterm strength and a multiaxial failure criterion leads to results that are more consistent with stress measurements performed in the field, in the vicinity of the mine.

Jun 1, 2012