Search Documents

By J. D. Campbell

"Coal is one of Alberta's major fuel resources, but its distribution, especially in the flat plains region, has been somewhat obscured by surficial deposits. After a period of neglect, easily strippable plains coal is presently approaching a position of dominance in electrical power production, a position it is likely to retain for a number of decades in the face of strong competition from hydro and nuclear power. Accordingly, the Research Council of Alberta has undertaken an inventory survey of the province's supplies of this resource.In the southern part of the province and in the north-central forest-fringe area, some strippable coal is found in the Belly River Formation and its equivalents, but major strippable coal reserves in large areas of central Alberta occur within the Edmonton Formation. The survey is planned on a reconnaissance scale, drilling test holes at 2-mile intervals in selected large areas. It appears to show that, in well-settled regions, large reserves of strippable coal are only to be expected where they have long been known; major presently unknown bodies of coal must be sought in unsettled regions or at depths too great for strip mining. However, such bodies might still be economically competitive with hydro and nuclear power in the production of electric power for some time to come."

Jan 1, 1967

By C. Tissot, R. Palmer

"Due to the low concentrations of gold, direct measurement of gold concentration in ore on belt has not been seriously considered to now. Pre-concentration or sorting strategies have largely consisted of particle sorting based on secondary characteristics such as colour, which can be successful in select cases. CSIRO has produced sample measurement results using gamma activation analysis of ~300 gm samples with accuracies of around 30 ppb at best. With this encouragement, a feasibility study into gold ore measurement on belt for the purpose of sorting pods of gold ore has been undertaken. The study described here included, prototype design options with existing industrial Linacs, extensive Monte Carlo modelling of measurement sensitivity and shielding, further sample measurement, a study of the interaction of target measurement accuracy and sorting efficiency, and a rough estimation of potential economic benefit. The projected model sensitivity of around 0.1-0.15 ppm (1 standard deviation) in 10 seconds for 1 ppm average feed result in good bulk sorting performance and intriguing economic potential.INTRODUCTION Pre-concentration or sorting strategies for gold ores have largely consisted of particle sorting based on secondary characteristics such as colour or density, which can be successful in select cases (Klein, 2010). No method is available to measure gold content for sorting in particles or even in bulk on belt, principally due to the low concentrations of gold present. In fact, in many cases it is difficult to do rapid bulk grade measurements of base metal ores with concentrations many orders of magnitude higher. By a fortunate quirk of nature gold is particularly amenable to gamma activation analysis (GAA). CSIRO has performed extensive work in GAA of samples of crushed ore (Tickner, 2017). This has resulted in the Photon AssayTM technique that is currently being commercialised through the CSIRO spinoff company Chrysos. The technique relies on the recent availability of industrial high intensity X-ray sources such as Linacs which are currently being used in industry for security, medical and sterilisation applications. This development has led to CRC ORE funding a feasibility study to determine whether on-belt measurement of gold concentration is possible at a rate and accuracy sufficient to be useful for bulk sorting, where pods of ore are diverted rather than individual rocks. The study in the first instance is based on Monte Carlo modelling that has successfully predicted the performance of the sample based gold measurements. As well as the measurement feasibility consideration was also given to the likely heterogeneity of gold ores and hence the degree to which useful separation could be achieved. This is then tied to a back of the envelope evaluation of the order of magnitude economics of bulk sorting in an example deposit."

Jan 1, 2017

By D. A. Riva

"The Line Creek Project is located in southeastern British Columbia, approximately 25 kilometres north of Sparwood. The design is to produce a total of2.7 million tonnes of coal annually. This is made up of1.4million tonnes of thermal coal and 1.3 million tonnes of metallurgical coal.Construction commenced in the spring of 1980 and mining operations began in July 1981. The thermal processing plant, maintenance and dry facilities, as well as extensive road and bridge construction, were completed in early 1982. A collective agreement was signed with the International Union of Operating Engineers, Local 115, in June 1981.The first unit train left Line Creek on February 18, 1982 with a load of thermal coal bound for the Ssangyong Corporation in Southern Korea. It was the start of a ten-year contract to supply 350,000 tonnes annually to fire their cement kilns. Additional contracts for 750,000 tonnes will fuel the boilers of Korea Electric Company's San Chon Po and Go-Jeong power stations. Metallurgical coal shipments are scheduled to leave the Roberts Bank port in Vancouver in April 1983.Tracking an introductory presentation given at the 1981 CIM Annual General Meeting in Calgary, this paper highlights the salient developments by which ""The Line Creek Project"" has progressed during the past year to the"" Line Creek Operation"". Line Creek has com e on stream as scheduled and will meet all contractual commitments pertaining to timing, volumes and quality for thermal coal. The first train load left the plant in mid-February, and the first boat load to Korea departed Roberts Bank in mid-April. Metallurgical coal deliveries will commence in April 1983."

Jan 1, 1982

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By J. G. Manchuk, M. Thurston

"The degree of uncertainty associated with a natural diamond resource is important to quantify from the time of discovery through the production lifetime. Data collection occurs during the discovery, exploration, delineation, and production or recovery phases. Quantifying the relationship between data and uncertainty is an important component of project valuation. The value of data is measured as their potential to reduce uncertainty if they are collected. A method is developed using Monte Carlo simulation for predicting resource uncertainty and valuing data during critical phases of development, particularly discovery and exploration. The technique is applied to diamond pipe deposits.RÉSUMÉ Il est important de quantifier le degré d’incertitude associé à une ressource diamantifère naturelle, depuis le moment de sa découverte et durant toute la durée de l’exploitation. La collecte de données se fait durant les phases de découverte, d’exploration, de délimitation, et de production ou de récupération. La quantification de la relation entre les données et l’incertitude est une composante importante de l’évaluation du projet. La valeur des données est mesurée en tant que leur potentiel à réduire l’incertitude si elles sont recueillies. Une méthode a été développée qui utilise la simulation de Monte Carlo pour prédire l’incertitude de la ressource et évaluer les données durant les phases critiques du développement, surtout celles de la découverte et de l’exploration. La technique est appliquée à des gisements de cheminées diamantifères."

Jan 1, 2015

By Shuo Zhang, Wenying Liu

"In dump leaching, the efficiency of metal extraction from ores is strongly influenced by the mechanisms of fluid flow. Particle size distribution acts as a fundamental parameter in the determination of fluid flow properties in packed ore beds. In this study, we investigated the particle size distribution in dump leaching by using image analysis technique. The results showed that the particles in the dump varied from smaller than 2 cm to larger than 200 cm in diameter. P80 was calculated to be 200 cm, which was significantly higher than the historical data used by the operation. P25, P50 and P80 were found to increase non-linearly with increasing depth towards the toe of the dump, suggesting the segregation of fine and coarse particles. The image analysis results were verified by applying the rock fragmentation models. The model with the Swebrec function was found to be in better agreement with the image analysis results. Future research will investigate the effect of particle size distribution on the behaviour of fluid flow.INTRODUCTION Fluid flow plays an essential role in the extraction of valuable metals using heap/dump leaching (Amos et al., 2009). The rates of the chemical leaching reactions and microbial activities determine metal concentrations in the leachates and therefore the efficiency of the metal extraction. The reaction rates are influenced by two fundamental processes: transport phenomenon and reaction kinetics (Bouffard & Dixon, 2001). The transport phenomenon refers to the percolation of fluids through channels and pores in a packed ore bed, which carries lixiviants and reaction products to/from ore surfaces by convection and diffusion. The percolation rate of the leaching solution is determined by the hydraulic conductivity of the packed ore bed, which is a function of the permeability and the degree of saturation (Guzman et al., 2008). Permeability, an intrinsic property of a packed ore bed, is strongly influenced by the particle size distribution of the ore grains (Bouffard & Dixon, 2001). Hence, the objective of this study was to investigate the particle size distribution in dump leaching."

Jan 1, 2017

By A. G. Spencer, A. D. Taylor

This paper discusses some of the advantages and problems associated with the selection of large unit equipment for a metallurgical plant. A given flowsheet and material balance for an iron ore concentrator is assumed. Then two plant designs are developed, one utilizing a number of smaller-size equipment units and one utilizing the largest available equipment units. The mechanical and electrical problems are discussed and a comparison of capital costs is made. Finally, brief consideration is given to a plant de-sign using units larger than those which are currently available.

Jan 1, 1968

By G. W. Harris, P. Mousset-Jones, J. Daemen

"To minimize ore dilution induced by blast movement in surface mines, it is necessary to quantify such movement. This will enable more accurate location of the grade boundaries beneath the surface of a blasted rock pile before excavation. A method has been developed and tested to accurately measure the direction and magnitude of subsurface blast movement. This technique uses a cesium vapour gradiometer and a real-time, differentially corrected GPS system to locate pre- and post-blast position of magnetically enhanced target objects placed within blastholes inside a bench. The procedure developed does not require the blasted rock to be disturbed, and the movement information is available within a sufficient time to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m, with the overall accuracy being measured as ±1 m (horizontally) and ± 1.2 m (vertically). IntroductionOre dilution is a critical concern for many mining operations. In some instances, it may be the cause of considerable mineral loss. Where the mineralization is finely grained, sedimentary and disseminated in nature, and exhibits no clearly defined visual ore/waste boundary, there is a heightened possibility for ore grade dilution. In most modern open pit gold mines, it is economically desirable to minimize dilution in the production process through the practice of selective mining by defining pre-blast ore digging boundaries, called digging polygons, on the preblast bench area. The polygons’ positions are defined by sampling the production drill holes, with the resultant assay and survey data being used to estimate the areas of specified grade content within the bench. Once the ore is blasted in the bench, the pre-blast locations of these digging polygons are flagged as designated areas on the broken ore pile. The purpose is for the loader operator to be able to recognize which areas of blasted rock are to be sent to the appropriate processing facility or to the waste dump."

Jan 1, 2001

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By A. LA. Salama, D. B. Hyma

"The Western Research Centre (WRC) of CANMET located in Devon, Alberta, is a modern research facility offering services ranging from fundamental research to pilot plant investigations. Recently, a 0. 76 metre diameter by 7.9 metre high Flotaire column flotation cell was installed as a demonstration unit for Canadian coal producers. Because the column cell is intended to be used for research, development and demonstration, WRC recognized that additional sensing equipment and improved process control would be required to generate good data for subsequent column scale-up and engineering design.A low cost, personal computer based control system was, therefore, designed and installed. This paper describes the stepwise procedure in developing the control strategies, selection of system software and hardware, and installation and configuration of the system.Preliminary performance data on a western Canadian coal sample are also presented. Future testwork is planned on additional coal samples to expand upon existing database."

Jan 1, 1993

By DON E. MacDONALD

Marl in Alberta is confined to highly specific geological, hydrogeologica/ and climatic settings. Tufa is fa irly abundant in those areas of western Alberta where bedrock is of the Paskapoo Formation. Marl and tufa originate when the following conditions are met: presence of a carbonate source in drift or nearsurface bedrock; leaching of the carbonate by percolating groundwater; transportation of calcium and bicarbonate ions in a permeable aquifer; discharge at the surface as springs, seeps or lakes; re-precipitation of calcium carbonate. Alberta has seven categories of marl and tufa deposits, based upon over-all depositional environment and calcium carbonate

Jan 1, 1984

By T. Feldmann, G. P. Demopoulos

The adsorption of gold complexes on inorganic metal oxides has been mainly discussed in geochemical literature, but it is also of interest to the hydrometallurgical industry. This is so because it could be responsible for valuable metal losses or because it could potentially serve as alternative adsorbent material to activated carbon in certain cases such as from hot and acidic process slurries. This paper constitutes an early investigation into this subject by focusing on the effectiveness of FeOOH, Fe3O4 and Al2O3 as sorbent materials. All tests were done in a batch stirred-tank reactor under atmospheric conditions with synthetic gold(III)-chloride solutions at 23°C and 80°C, in the pH range of 1.6 to 9.0. Detailed kinetic tests were performed at different pH values (3 and 6) on FeOOH and Fe3O4 with solutions having gold concentrations from 5 mg/L to 130 mg/L. The adsorption of gold was found to be best both in terms of kinetics and loading characteristics at 80°C and pH=6. This was explained by a change in Au(III)-Cl speciation from a gold(III)-chloride complex to a gold(III)-chloride-hydroxy complex. By far, magnetite (reagent grade chemical) yielded the best gold adsorption characteristics making it an interesting sorbent material for further development considering that it can be advantageously recovered from slurry streams via magnetic separation. On the other hand, the tendency of gold(III)-chloro complexes to adsorb on metal (hydro) oxides needs to be taken into account to minimize undesirable metal losses in chloride-containing leaching media.

Jan 1, 2015

By W. M. Tupper

Municipal governments recognize the importance of aggregates in the local economy and the need to manage this resource in the interest of the public good. They have encountered problems with regulating the industry and the dichotomy between the urban need and the rural source. They have suffered from a lack of financial benefit, an adequate aggregate inventory, provincial strategy, economic information and public understanding. A provincial strategy for ensuring the availability of aggregate supplies to developing areas of the Province is essential. The Province should also be responsible for licensing, research, technical expertise on rehabilitation, public education and financial assistance. Upper-tier municipalities (regions or counties) should assume responsibility for resource management, including resource availability, demand characteristics, truck routing, phasing of resource development and sequential land-use planning. Area municipalities (towns and townships) can best determine the social and environmental impact of a specific aggregate development proposal and should therefore have the primary responsibility for the location of new pits and quarries. They should also have the authority to supplement provincial regulations concerning operating standards and the phasing and standards of site rehabilitation.

Jan 1, 1978

By Robert E. Loftus

"The author discusses the growth in the use of ocean-going bulk carriers for the transportation of mineral commodities, and predicts future trends. The various types of tonnage carriers are described, along with the special discharging gear used, the costs involved and the duties of some of the personnel.THE FIRST CONSIDERATION in planning the ocean transportation of minerals is the type of vessel to be utilized. The modern 'Bulk Carrier' bas proved to be the most successful vehicle for the purpose. I would there-fore like to describe this fleet in some detail and at-tempt to show the impact that the bulk carrier bas bad on the movement of bulk materials."

Jan 1, 1968

By T. Ouellet, F. Chiesa, J. Carignan, D. Levasseur

Common practice for the preparation of permanent mold for aluminum casting is to coat the mold with a ceramic suspension to obtain a chemically stable interface with the aluminum melt. This practice serves two purposes: first, it helps the thermal regulation of the mold and second, it prolongs its life. The possibility of increasing the coating durability by applying it by thermal spray is appealing. Plasma spray of zirconium oxide based coatings was performed on H13 tool steel to study the coating’s thermal fatigue resistance. A unique dip test setup was used to characterize the thermal fatigue resistance of the coatings and of bare H13 steel. Observations of the failure mechanism bring an insight on the requirements of the coating to maximize its durability.

Jan 1, 2014

By Tuula Mäkinen, Lauri Pesonen, Peter Björklund, Jouni Pihlasalo, Mikko Korpi

Outotec Direct Blister Flash Smelting technology has proved to be an efficient and environmentally friendly way to treat copper concentrates from the Zambian Copperbelt at Konkola Copper Mines' (KCM) Nchanga smelter in Zambia. The modeling of slag chemistry and thermodynamics with MTDATA software played a central role in deciding the operation parameters for the smelter. Outotec FSF Online Process Advisor is used to calculate the process parameters and to give valuable information of the process state for the operating personnel. The pre-calculated slag liquidus graphs are also integrated to the Online Advisor.

Jan 1, 2011

By M. S. Diederichs, J. Oke

Surface limitations and a need for more direct transportation routes require serious consideration be given to the development of underground construction works in geotechnically unfavourable conditions. Due to geographical and logistical limitations, the construction of these underground works is restricted to difficult ground conditions that require temporary pre-support before excavation in order to avoid tunnel collapse or severe surface settlement. One type of pre-support is the umbrella arch system, which has been gaining popularity due to cost and time commitment in comparison with other pre-support systems (e.g., ground freezing). The umbrella arch system has been employed with significant frequency around the world, yet without a complete understanding about the mechanical response of the system. As such, literature has found the temporary support system to be both under and over designed with regard to safety and/or economical impact. The authors of this paper have made three major contributions to increase understanding of the umbrella arch system and to help optimize the design process. Firstly, the authors have developed nomenclature in order to categorize and define umbrella arch elements and systems, which also stimulated the creation of the empirically driven Umbrella Arch Selection Chart. Secondly, the authors have established a design methodology that is primarily based on advanced numerical modelling techniques to aid in the optimized design of the umbrella arch arrangement for site specific conditions. Thirdly, the authors have developed a semi-analytical model for umbrella arch systems employed in squeezing ground conditions by incorporating elastic foundation theory as well as convergence confinement theory. These three major contributions to such a widely employed tunnelling pre-support system will be introduced and explained in detail, and will include discussion of how each is incorporated in the complete tunnel support design process and throughout the construction and monitoring phase of a project.

Jan 1, 2015

By Jan Butra

In copper ore mines located in the Pre-Sudeten Monocline the deposit mining using room and pillar systems has been carried out for more than forty years. When implementing mining systems in deep copper ore mines it appeared to be necessary to adapt them to variable geological conditions and natural hazards. In the initial period of exploitation there were mainly caving and rockburst hazards. The adaptation of room and pillar system was connected with a state of knowledge in the scope of identifying, forecasting and controlling rock mass hazards. The new solutions allowed the safe and efficient exploitation of a blanket deposit of variable thickness from about 2 to 15m, seated on progressively increasing depth. They included exploitation in constrained conditions, such as in protective pillars. In the exploitation period, technical and organisational activities aimed at rockburst hazard control were introduced including active methods for controlling rockburst hazard and procedures for conducting mining works in the rockburst hazard conditions. When mining at a depth exceeding 1,200 m, the exploitation method and technique are additionally affected by thermal hazard and by gas and rock breakout hazard. New solutions of the room and pillar system and a longwall system with mechanical mining have been developed for exploitation in the associated hazard conditions. The require application of many innovative solutions in the scope of mining process and ore haulage mechanisation, excavation support and forecasting and control of existing hazards. The main purpose of these solutions is to conduct the safe and economically effective exploitation of the deposit.

Aug 1, 2013

By Robert B. Parsons

"In all likelihood, Canada's mining industry would be adversely affected by corporate tax reform proposals actively being considered by the Department of Finance in Ottawa. When the next set of proposals for lax reform is released later this year as promised by Finance, the mining industry had better be prepared 10 take a hard look.IntroductionTwo federal budgets ago, in May 1985, Finance Minister Wilson tabled budget papers that were more massive in terms of volume than most federal budgets. Buried in this mass of documentation is a discussion paper entitled ""The Corporate Income Tax System-A Direction For Change"". When the discussion paper was tabled over one year ago, reaction from the business sector was almost nonexistent. By and large, the paper was regarded as nothing more than one more federal publication of mild academic interest.But, recent events suggest that this discussion paper for corporate tax reform could be the cornerstone for a series of changes to the tax laws which would have more profound and widespread effects for all sectors of the economy than any reform since 1971 . No industry in Canada can afford to ignore the movement afoot in Ottawa for corporate tax reform."

Jan 1, 1986

"RÉSUMÉOn discute les principales sources de dilution au cours d’une exploitation souterraine. Les différentes définitions de la dilution en usage sont analysées. Une nouvelle méthodologie de calcul simplifiée et facile à utiliser dans la pratique minière est présentée. Cette méthodologie permet de remplacer les différentes expressions analytiques en usage par les deux facteurs de dilution seulement : un «facteur de dilution planifiée» lié à la sélectivité d’abattage au niveau de la planification minière et un «facteur de dilution additionnelle » permettant de juger de l’efficacité du contrôle de terrain et de la dilution pendant l’exploitation souterraine. L’application de cette méthodologie donnerait un outil nécessaire aux niveaux de la planification, du suivi des travaux d’exploitation et d’éventuelles études comparatives des coûts entre les différentes situations minières.ABSTRACTThe principal sources of dilution during underground evaluation and mining are discussed, then definitions of ore dilution currently in use are analyzed. These definitions vary depending on the authors. A new ore dilution evaluation methodology is proposed, replacing the ten different analytical expressions by only two: the planned dilution factor related to the stoping selectivity, done at the mine planning level, and the additional dilution factor related to the efficiency of the dilution control measures during stoping operations. The conclusion shows that the use of this methodology would be a definitive asset in planning, in stoping operations follow-up, and in future costs comparison studies between mining operations."

Jan 1, 2001