Search Documents

By Baisheng Nie, Longlong Yang, Tao Yang, Wenjie Jia

"Gas adsorption in coal is an exothermic and physical process. Temperature might change during the dynamical process. In order to get the temperature variation of gas adsorption process, the experiment system which can test the temperature variation and analyze the thermal effect was established. Gas adsorption experiments under different conditions were done by using the test system. The results show that temperature increases during the adsorption process. It is an exothermic reaction process. Also, the temperature variation and the variation gradient increase with the increasing of equilibrium pressure. The temperature variation value is smaller if the experiment temperature is higher. The paper will provide basic experimental data for explaining gas adsorption mechanism better.INTRODUCTIONChina is the largest coal producer in the world while it also has the most serious coal mine disasters. According to the statistics, there are nearly a thousand coal mines in China including more than 110 the key state-owned mines risking to happen coal and gas outburst. Hundreds of coal and gas outburst occur each year which often causes serious casualties and economic losses (State Administration of Work Safety, 2007). With the continuing exploitation of the coal resources, the depth of the Chinese coal mines increases about 100 meters every year which causes the situation of gas accident becoming more and more serious (Xie et al., 2006).At present, the real mechanism of gas adsorption, desorption and the diffusion process in coal and the influence factor of it are not so clear. And because of the limit of prediction method and the technological level caused gas accident prevention theory and technology not so valid."

Jan 1, 2015

By Lawrence Devon Smith

The selection of the production rate is one of the most crucial decisions to be made in the development of a mineral property. However, it is not uncommon for the production rate to be decided arbitrarily, before any technical evaluations begin, and it is often not reconsidered when better data becomes available. A number of methods are used in the mineral industry to select the production rate for a project. There is general agreement that the size of the ore reserve has a strong influence on this decision, but what other factors are involved? Is there a way to identify an optimum rate? This paper examines the factors that influence the selection of a production rate from the perspective of project economics. The NPV maximum value should be viewed as a “failure” point. The “two times capital” maximum is proposed as a lower limit. A practical check is suggested to confirm that a selected rate is in an optimum range. Production rate assumptions are much more likely to be reviewed for marginal projects, but they should also be reviewed for viable projects.

Jan 1, 1997

By Harvey McLeod

M3 -Technology HOWEVER:In practice we have limitations ?Clients: aggressive or cost based; inexperienced ?Consultants: ?expanding market w/training limitations ?Prescriptive designs ?Lack of senior oversight ?Regulators: difficult to retain technical capacity ?Stakeholders: perceptions and expectations ?Physical settings: challenging terrain, climate, soils/rock Do M3?s Perform? YES?Generally M3?s since mid-1960 do perform ?BC Closed Mines: Afton, Highmont, Trojan, Bethlehem, Cheni, SNIP, NO?ARD/ML issues?e.g. Equity Silver, Samatosum; selenium, cadmium, sulphate

May 1, 2010

By Dean Millar

Clean, green, cheap compressed air can be produced efficiently and renewably by modernization of a 19th century technology ?The hydraulic air compressor has no moving parts ?After commissioning, the Ragged Chutes HAC operated for 70 years, only being stopped twice for repairs to the intake heads ?Operates using hydropower from Montreal river ?Produced air for ~29 silver mines in Cobalt, 20 km distant

May 1, 2013

By J. J. Jonas, G. R. Stewart, A. M. Elwazri

Two important parameters for dynamic recrystallization can be derived from the changes in the strain hardening rate: the critical strain for initiation of dynamic recrystallization and the point of maximum softening. In this work, these values are determined from the flow stress-strain data obtained in continuous compression testing in the range 900-1100°C. The resulting strains are used to calculate a kinetic model of dynamic recrystallization for two materials: 304 austenitic stainless steel and a hypereutectoid plain carbon steel. The mechanical parameters used to define the proposed model are confirmed with quantitative metallographic analysis of the recrystallized microstructure.

Jan 1, 2004

By M. Pierce

Empirical relations exist for the estimation of rock block strength at scales larger than standard core sizes. Two recently published relations account for the significant impact that microflaws (pores, open cracks, veins) and weathering/alteration can have on scale effect. These relations were used to estimate the rock block strength of heavily microfractured quartzite from the Bingham Canyon Mine. Predictions were compared to the results of Uniaxial Compressive Strength (UCS) tests conducted on cylindrical core samples of varying microfracture intensity and diameter. The comparison confirms the sensitivity to microfracturing suggested by existing relations and suggests that they would benefit from more detailed consideration of microfracture strength, density and persistence over a range of scales. The results of a numerical study illustrate how Synthetic Rock Mass (SRM) modeling techniques could be used to complement empirical data in the development of such relations.

May 1, 2009

By F. C. Robles Hernandez

This paper presents the results of the electromagnetic semi-solid treatment of the 319 aluminum foundry alloy, Various levels of structure modification were achieved controlling the AC current used to create the Electromagnetic Field, thus manipulating the intensity of the field, The level of grain refinement, partial modification of the Al-Si eutectic, as well as cellular dendrites were observed, A quantitative analysis of the structure was performed using Image Analysis (IA) techniques. In addition a novel Thermal Analysis methodology was developed for the on-line determination of the microstructure modification level.

Jan 1, 2004

By G. R. Sadowski

"Large subhorizontal joints have been found in the foundation excavations in basalt and granite of Brazilian Dams. Some spread for hundreds of square meters showed slickensides—polished surfaces plus striations—and laminations interpreted as related to shear displacement, what substantially reduced their shear strength and imposed special reinforcement measures against the potential sliding of overlying concrete structures. The geological characteristics of these discontinuities have raised speculations related to their origin, be it related to mechanisms of bulging, cambering or to some tectonic or primary geological event.Several geologists and engineers from the northern hemisphere including Terzaghi already showed to be concerned with their role in granite foundations while in the southern regions Brazilian authors have found similar occurrences but also affecting individual lava flows of continental flood basalts in the foundations of major dams of the Parana Basin, which they designated under the particular name of “fault-joints”. This double-standard designation is self-explanatory of the difficulties involving their origin and related geomechanical properties: faults or just shear joints?Recently, similar features were encountered in the foundations of large dam constructions in anorogenic granites inserted in the realm of the Brazilian Amazon, where some of these discontinuities exhibit features common to tectonic thrusting combined with deep tropical weathering.The evidence of preshearing along the surfaces of such fractures, also associated to products of deep weathering, reduces their geomechanical strength substantially, suggesting values of ultimate phi spanning 12 to 28°. The detection of these descontinuities during initial investigation phases continues to be a major complex task in geological risk evaluations surveys. Trenching associated to some geophysical exploration techniques, although considered to be very basic exploration techniques are still the suggested methods for their forecast and previous determination."

Jan 1, 2015

By A. R. Turner

AERIAL survey methods have made enormous technical advances and gained new recognition since World War II. Before enlarging on this statement and reviewing some of the uses of aerial survey in industrial development it is important to de-fine what is meant by "aerial survey". The subject will be discussed in the broadest sense and references will be made to the four sections that compose the overall field of surveying operations from the air. These are: 1. Aerial photography and photo-graphic mapping. 2. The use of airborne electronic instruments for geodetic distance measurement and the determination of ground elevations. 3. Airborne geophysical surveying. 4. The extraction of qualitative and quantitative information from aerial photographs through the processes of "reading", analysis and interpretation. Many sciences and techniques are combined in aerial survey operations. The tools of the business include aircraft, finely engineered cameras, elaborate film processing and printing equipment, ground survey instruments, precision stereo-plotting instruments, map -

Jan 1, 1961

By Peter C. Jones, Wanda M. Carter, David H. Watkinson

"Abstract - Pyrrhotite, chalcopyrite, and pentlandite are the dominant sulfide minerals in the 740 zone of the Kelly Lake orebody (Inco Ltd.), Copper Cliff Offset, Sudbury. Petrographic and quantitative electron microprobe analyses of minerals, from sulfide assemblages and host quartz diorite, of the 740 deposit have revealed three processes that have affected sulfide mineralization and associated sulfarsenide and platinum-group-mineral (PGM) distribution: magmatic, hydrothermal, and tectonic. Accessory, zoned cobaltite, and gersdorffite occur in sulfides as a result of these three processes, and PGM occur dominantly in hydrothermally remobilized and deformed ores. Where PGM are present in sulfarsenides they provided nuclei for sulfarsenide growth. Solitary PGM are orders of magnitude larger than those PGM found within sulfarsenide minerals. Five varieties of PGM occur, michenerite and sperrylite being the most common, with lesser froodite, hollingworthite, and ruarsite.The effect of a deformation is a localized fabric in the ore, revealed by pyrrhotite and chalcopyrite bands; pentlandite porphyroblasts also partially define the foliation. The deformed ore is also characterized by alteration of the adjacent quartz diorite, which produced an alteration assemblage including almandine garnet, Fe-rich biotite, and chlorite."

Jan 1, 2001

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By Rocky (Yaokun) Wu

Rock burst is one of the biggest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost effective yielding rock bolt. This paper introduces a new yielding rock support - Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150 ~ 250 mm of deflection at 8 ~ 10 metric tons (Mt) loads for every 16.4kJ energy input. Its performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described, the dynamic testing results are discussed; and the features and application of the bolt are presented.

Oct 1, 2010

By K. Spence

"The notion of “value” has always been a subjective and contentious issue. Indeed, value is in the eye of the beholder. There are as varied methods and practices for valuing property, as there are industries in which they are applied. For example, there is replacement value, insurance value, salvage value, appraised value, book value, and fair market value, to name a few, although in the mining industry, valuations usually refer to fair market value.In the Canadian mining industry, at present, there are no comprehensive regulations or guidelines that specify which approaches or methods are appropriate for use in the valuation of mineral projects. In January 1999, The Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. Among the approaches to be considered are included the following: the discounted cash flow approach, the cost approach, the option pricing approach and the market comparables approach. In addition, methodologies differ depending on whether the project is at the exploration stage or the producing stage.The CIM Special Committee on the Valuation of Mineral Properties (CIMVal) expects that its final report will form the basis for a Canadian code or standard for the valuation of mineral properties."

Jan 1, 2002

By A. G. Slade

"This paper deals with the direct application of rock mechanics in the underground mines at the Sudbury Operations of Falconbridge Nickel Mines Ltd. It covers mining methods, the use of photoelastic models, the fore-casting of rock strains and their elimination, closure methods and other common methods of ground control.INTRODUCTIONROCK MECHANICS IS A STUDY IN ROCK BEHAVIOUR and, although it is being termed a new science, it has been practiced since the industry began. Every person involved with rock excavations, from the mine superintendent to the stope driller, is actually practising rock mechanics. They probably call it by another name -experience, and applications of this knowledge are in evidence throughout the Falconbridge operations. Only in recent years have formal rock mechanics studies been employed to provide technical assistance to the mine operators in their primary objective of producing ore safely."

Jan 1, 1968

By A. Zorkovská, S. Castro, P. Baláž, Z. Bujnáková

Enargite (Cu3AsS4) belongs among refractory copper minerals with very low hydrometallurgical extractability of copper. An application of enargite leaching in acid solutions leads to simultaneous dissolution of copper and arsenic and the final leach solutions have to be treated for the separation of both elements. However, the alkaline leaching of enargite is selective. Arsenic passes into leach while produced copper sulphide represents the raw material suitable for pyrometallurgy. The hydrometallurgical processing of mineral can be influenced positively by mechanochemical route. We have shown that more than 80 % of arsenic can be extracted from enargite concentrate by atmospheric alkaline leaching at 95 °C when mechanical activation in an attritor is applied. The produced Cu2S can be further treated with elemental iron where mechanochemical intervention is applied in the second stage of enargite processing. The final product forms Cu/FeS nanocomposite from which copper nanoparticles can be easily separated. The illustrated concept of copper obtaining from copper sulphide is an example of so-called “dry” processing, as reactions in gas and liquid phases are excluded. This concept of environmentally friendly metallurgical processing can be classified as an impetus for novel technology to produce copper from enargite concentrates.

Jan 1, 2012

By M. A. Mahtab, A. S. Burgess, R. G. Charlwood, P. O. Sandstrom, J. L. Ratigan

"Addressing a current operating and environmental concern, this paper first presents an overview of the design program for an underground radioactive waste storage vault. It then reviews the construction, operational and thermal-mechanical aspects of such a project. The relevant experience from major underground construction projects is reviewed and the paper concludes with brief comments on the design-oriented research and development requirements . 1. IntroductionA program to develop techniques for the ultimate disposal of high-level radioactive waste into geologic formations was announced by AECL in 1975 (Tamrnernagi, 1976), and is discussed more fully in a later document (Boulton, 1978). Our paper summarizes the studies caried out, as part of the AECL waste management program, by the authors and associates on the development of design concepts for a vault situated in crystalline rocks of the type present in the Canadian Shield.The design studies have been carried out in three phases, the elements of which are described in Section 2.1 (also see Fig. 1). The general vault designs are presented in Section 2.2. These provide for emplacement of either immobilized fuel or solidified reprocessing wastes in a room-and-pillar facility at a depth of 1,000 m.Section 3 reviews the principal design considerations from the construction, operation and thermal-mechanical response aspects. The concepts have been studied in both temporal and spatial domains, and the requirements and responses assessed in each as appropriate.Section 4 briefly reviews the availability of relevant experience from previous major underground construction projects. Finally, in Section 5, brief comments are given regarding design-oriented research and development requirements."

Jan 1, 1980

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By S. Esfahani, M. Barati, Y. Kauwachi

"Heat recovery from slag has gained attention due to its high potential in lowering energy intensity of metal extraction processes. A direct method to recover the thermal energy of slag is to use countercurrent air flow that extracts the heat from falling droplets. Often, the solidified slag is aimed to be used as a substitute for Portland cement, thus high cooling rates are required to form an amorphous slag with sufficiently strong hydaulicity. Rapid cooling however involves using large gas flow rates that in turn lower the thermal efficiency of the process. This article presents a mathematical model that was developed to determine the optimum conditions in the heat recovery process and to investigate the effect of the air flow and granule diameter on the cooling rate of the droplets as well as the thermal efficiency of the heat recovery system. INTRODUCTIONMetallurgical slags are the largest by-product of high temperature materials refining and extraction processes. The total amount of metallurgical slag produced in the year 2008 has been estimated at up to 422 million tonnes containing up to 222 TWh/y (Barati and Esfahani, 2011) of thermal energy. Over the past four decades attempts have been made to recover this substantial amount of energy as heat, electricity, or fuel, while none of the proposed method has been commercialized yet.During slow cooling the slag tends to crystallize the constituents (CaO, SiO2, Al2O3, etc.) into a hard, heavy solid. In the past, over 90% (Bengt, 1983) of the molten waste was discharged onto heaps and allowed to cool slowly, then crushed and used in road construction or land filling or as coarse aggregate for concrete. However, later it was found if cooled rapidly, the slag can be used as a substitute for Portland cement. As a result, processes such as wet granulation were created in which molten slag is fragmented with water, forming amorphous (glassy) phases. Despite its effectiveness in producing a suitable material, heat would not be recovered through this process. Thus, dry granulation was introduced in 1930’s and was developed further in 1970 – 1980’s."

Jan 1, 2012

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007