Search Documents

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By P. Rocque, S. Talebi

Although the measurement of blast vibration close to the blasthole is critical to the understanding of rock fragmentation mechanisms and blast damage in the rock masses, limited experience for such monitoring exists. Because much higher vibration amplitude and frequency ranges are expected in rock masses close to an explosive charge as compared to far field vibrations, different problems from those for the far field monitoring must be considered for near field blast vibration monitoring. Currently, guidelines for design of the near field blast monitoring systems do not exist. This paper describes the development of an integrated technique for vibration monitoring close to a blast hole, including selection and installation of transducers, design of a monitoring system and signal recording. A densified cement was designed for grouting accelerometers in order to match p-wave impedance between the rock and grout. The monitoring technique described has proven suitable for blast vibration monitoring within 2 m to 15 m of a blast hole having loading conditions similar to production blasts.

Jan 1, 1993

By P. Leo

The hot deformation behavior of a Mg-9A1-1Zn alloy produced by high pressure die casting has been investigated by means of compression tests in the temperature and strain rate ranges of 125-300°C and 10-5-10-1 s-1 and torsion tests over 150-450°C and 5, 0.5, 0.05 5-1 . The compression samples were deformed in the die-cast state or after homogenization at 415°C for 2 h to evaluate improvements. A premature fracture at 45° with respect to the compression axis was observed in samples strained at low temperatures and high strain rates. The torsion specimens were tested as received or after a predeformation-homogenization treatment. In addition to constitutive analyses suitable for modeling previously published, the results are fitted to a relationship between strain rate normalized by diffusion coefficient and flow stress normalized by modulus. The results fit well with a set of published creep experiments that were conducted in the range of 70-150°C.

Jan 1, 2006

By D. B. Haas

THE HYDRAULIC TRANSPORT of solids is becoming increasingly prevalent throughout the world. Major long-distance slurry pipelines currently in operation transport commodities such as coal and various ore concentrates distances of up to hundreds of miles. In the United States, a number of large-diameter, high-tonnage pipelines are under consideration for the transport of Western Plains coal to markets up to 1000 miles away. In these and other applications, the solids are generally quite fine, with 14 mesh being a typical limit of particle size for long-distance (over 100 miles) slurry transport. There are applications where it might be practical to transport solids consisting of larger particles distances of up t o 100 miles. Deposits of high-quality metallurgical coal are found in the inner foothills belt along the eastern edge of the Rocky Mountains on the Alberta-B. C. border. There are few existing railroad s and the possibilities of constructing extensions are limited because of environmental and economic factor s. In these circumstances, the most efficient transportation system might consist of a pipeline to transport the coal from the mine to beneficiation plants located near existing railroads 50 or 100 miles away. Such systems would minimize environmental effects, capital cost s and operating costs. To determine whether such a system would be technically feasible, experimental testing is needed to determine the energy requirements for transporting coarse coal in a pipe line. Currently, run-of-mine metallurgical coal is crushed to less than 1 1/2 inches before going to the beneficiation plant. In the proposed scheme, coal of this size would be transported through a pipeline to the beneficiation plant located at the railroad. The Transportation Development Agency and the Department of Supply and Services have awarded a contract to the Saskatchewan Research Council to study pipelining of coarse coal in pipelines ranging from 4 inches to 12 inches in diameter.

Jan 1, 1977

By H. J. McQueen

The modeling of the extrusion of 6061 alloy and its composites with 10 to 20 vol% Al203 or SiC by two techniques. The uniaxial finite element method FEM (DEFORM" ) provided force-stroke curves and temperature rise over the range 450-500 °C, 2.6-5mm/s and extrusion ratios of 31 and 64. The traditional technique considers ideal work and redundant work as well as friction and uses average temperatures and strain rates. The two techniques are used to clarify each other and to extend the analysis to 400 and 350 °C. The calculated efficiencies are compared to measured values in extrusion trials and to values derived for 7075 extrusion analyses. The analyses are based on constitutive equations determined by torsion testing tests.

Jan 1, 2004

By Z. Zhang, D. Bouchard, H. Blanchette, A. Lemieux

This paper describes quality control methodologies for the production of semisolid A356 aluminum slugs with the SEED process. A methodology based on destructive tests carried out with an apparatus measuring the force to slice the slugs is presented. The force measurements were correlated with the solid phase morphologies of the slugs and were validated against a non destructive methodology that consisted in monitoring the temperature evolution of crucibles to produce the slugs and the drained metal. Results from the destructive and non destructive methodologies are compared and discussed.

Jan 1, 2006

By L. R. Fyffe, D. R. Lentz, S. H. Mcclenaghan

"Abstract - The Eel River area in the southwestern Miramichi terrane of New Brunswick contains a complete calc-alkaline suite of volcanic rocks that are interlayered with intervals of sedimentary and polylithic fragmental rocks, and are overlain by a thick sedimentary sequence. This package, collectively referred to as the Meductic Group, was deposited in a submerged volcanic arc setting interpreted to be part of the Popelogan arc. Rifting of this arc led to the development of the Tetagouche-Exploits back-arc basin, and formation of volcanogenic massive sulfide deposits in bimodal volcanic rocks of the Bathurst Mining Camp in the northeastern Miramichi Terrane. Unlike the Bathurst Mining Camp, volcanic rocks in the southeastern Miramichi Highlands form a continuous calc-alkaline suite characterized by increasing Zr/TiO2 with increasing SiO2, in part resulting from progressive coupled assimilation and fractional crystallization of nested magma systems. Slumping of semi-consolidated volcanic and sedimentary rocks in topographically unstable areas resulted in numerous slumps and debris flows that are preserved throughout the Eel River area. In the early 1990s, the discovery of a large sulfide clast in a road cut along the Benton road sparked interest in the volcanogenic massive sulfide potential of the Eel River area. Subsequent drilling intersected smaller fragments, one clast of which graded 16.7% Zn, 5.6% Pb, 90 ppm Ag, and 220 ppb Au. The intersection of thin lenses of stratiform sulfides in another drillhole indicates favorable conditions for the preservation of massive sulfides. Their subsequent incorporation into synvolcanic debris flows resulted in the transport and deposition of sulfide clasts from hydrothermal vents to more distal locations. Similar to the Buchans deposits of Newfoundland, tracing these debris flows back to their source would be beneficial from an exploration perspective. Approximately 15 km to the southwest of the Eel River area, gold-bearing base metal sulfide clasts (11.1% Zn, 6.13% Pb, 0.19% Cu, 108 ppm Ag, and 1100 ppb Au) occur within intermediate-composition volcanic rocks at Monument Brook in eastern Maine. Sommaire - Le secteur d’Eel River dans le sud-ouest de la terrane de Miramichi au Nouveau Brunswick contient une séquence complète de roches volcaniques calco-alcalines interstratifiées avec des roches sédimentaires et fragmentaires polylithologiques, sous une épaisse couverture sédimentaire. Cet assemblage constitue le Groupe de Meductic, et a été déposé dans un environnement d’arc insulaire interprété comme une partie de l’arc de Popelogan. Le rifting de cet arc à mené au développement du bassin d’arrière-arc de Tetagouche-Exploits, et à la formation de gisements de sulfures massifs volcanogènes dans les roches volcaniques bimodales du Camp Minier de Bathurst dans le nord-est de la terrane de Miramichi. Contrairement au Camp Minier de Bathurst, les roches volcaniques des hautes terres du sud-est de Miramichi constituent une suite calco-alcaline continue caractérisée par un accroissement du rapport Zr/TiO2 à des valeurs croissantes de SiO2, résultant en partie de l’assimilation progressive et de la cristallisation fractionnée de systèmes magmatiques superposés. L’effondrement de roches volcaniques et sédimentaires semi-consolidées dans des secteurs topographiquement instables est à l’origine des nombreux slumps et coulées de débris qui sont préservés dans le secteur d’Eel River. Au début des années 1990, la découverte d’un large claste de sulfures le long de la route Benton provoqué un intérêt pour le potentiel en gisements de sulfures massifs volcanogènes dans les secteur d’Eel River. Des forages ont par la suite recoupé des fragments plus petits, dont un claste qui a retourné des teneurs de 16.7% Zn, 5.6% Pb, 90 ppm Ag et 220 ppb Au. Le recoupement de minces lentilles de sulfures stratiformes dans un autre forage indique des conditions propices à la préservation des sulfures massifs."

Jan 1, 2006

By H. J. Glass, J. G. L. Bekkers

"In order to determine the feasibility of a hydraulic ore hoisting installation, the optimal operating conditions were calculated for applying such a system at the Detour Lake Mine of Placer Dome Ltd. Next, a financial analysis was conducted in order to estimate the cost per tonne for hydraulic hoisting of the ore. Subsequently, the cost per tonne was compared with the hoisting costs associated with a new borehole hoist. Installing a hydraulic ore hoist at Detour Lake Mine was found to be feasible with considerably lower costs per tonne of ore. The applied research method appears to be very functional and can be used to do similar research for other mining operations. IntroductionThe principle of hydraulic ore hoisting is well known, yet hardly accepted in hard rock mining. Application of the system would result in a smaller diameter shaft requirement and a flexible, easily expandable system. However, underground ore size reduction might be necessary and practical experience with the system is limited. Following recent innovations in the field of pumping hardware, e.g. new GeHo and Siemag Transplan equipment, hydraulic ore hoisting should be seriously considered for certain mining operations. As a case study, a design was made for the development of the newly found QK-Zone at Placer Dome Ltd.’s Detour Lake Mine. Hydraulic ore hoisting has been compared with conventional skip hoisting by establishing the optimal operating conditions and pumping equipment requirements for similar capacities at a selected mining operation. Generally accepted equations for slurry transport were used to predict the variation of pressure and power requirements as a function of hourly production and pipeline diameter. These data are used to select suitable equipment and estimate cost figures in order to make a financial assessment."

Jan 1, 1998

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

By T. Newton, G. A. Bezuidenhout, P. J. Tauetsile, F. Trask

The technology to selectively leach gold, silver and base metals from ores, concentrates, and wastes, using an alkaline glycine solution, has initiated significant interest in using the new technology in various environments such as in-situ, in-place, dump, heap, and vat and agitated tank leaching. It has been shown that glycine acts synergistically with a number of other lixiviants to lower the net consumption of the other lixiviants while allowing low cost glycine solution recovery. Glycine is a non-toxic, stable, environmentally benign reagent that is available in bulk industrial quantities. It has the ability to dissolve most copper oxide and sulfide minerals, as well as native copper, whilst not interacting with acid consuming gangue nor dissolving iron and various or ubiquitous gangue elements. It acts synergistically with small amounts of cyanide to leach gold-copper ores at leach rates higher than either glycine or cyanide on their own, while significantly reducing cyanide consumption and eliminating detoxification requirements. The leaching behaviour of various glycine based systems will be reviewed, followed by the evaluation of the adsorption of gold onto activated carbon. Where the economics merit it, copper can be easily recovered using solvent extraction or sulfide precipitation.

Jan 1, 2017

By R. Bonifaz, R. Subiabre

The Chagres Smelter, part of the Anglo American plc group, situated 80 Km north of Santiago in Chile, completed a series of operational improvement in 2005 resulting in an optimum capacity in its operational units. At present the Chagres Smelter has developed an operational strategy which seeks to reduce bottle-necks in the production process. In this way we have managed to lower operational cost, decrease energy consumption and maximize the capacity of the Acid, Oxygen, and Smelting, Converting, Refining and Casting units. A constant review of international benchmarks together with continuous staff improvement and the latest smelter technology have combined to place Chagres among the finest smelting works in the world. In response to environmental challenges, we have studied various options for investment that will yield a suitably profitable business to benefit both Anglo American and Chile. The most relevant technical indicators are: energy consumption=6,3 GJ/ton fine copper (1st in the world), intensity of smelting rate in Flash Smelting unit of 6,900 ton of copper concentrate/m2 of furnace area (1st in the world) and to be one of the top five smelters in achieving the lowest direct cash cost .

Jan 1, 2007

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

By R. E. Bou Serhal

Many miners are exposed to dangerously high levels of noise on a daily basis. Over the past 15 years, a continually increasing number of occupational hearing loss has been reported from the mining community in the United States, of which, more than 95% is attributed to prolonged noise exposure. Although the noise exposure levels may differ between coal miners and metal and non-metal miners, in the absence of noise control at the source, the solution is the same: use of personal hearing protection devices (HPD). While protecting the miners? hearing it is also essential to no longer hinder their ability to communicate. With access to an advanced HPD that is customized to the miners? ears we are able to combine these two requirements. Using an intra-aural instantly custom molded HPD miners are protected from high levels of noise. The HPD is equipped with wireless capabilities, and contains both a speaker and an In-Ear Microphone (IEM). Therefore, the miners? speech may be captured from inside the ear and transmitted to the remote listener. This IEM signal is relatively noise-free since it is isolated from the background noise. The IEM speech signal, however, is ?boomy? and is missing some high frequency content, making fricative consonants hard to understand. Nonetheless, the IEM speech signal is correlated with the natural speech signal and may be manipulated through statistical techniques to more closely resemble natural speech. By improving the intelligibility and quality of the IEM signal, numerous applications may be enabled. One use of the enhanced IEM signal will be for radio communication. Using wireless radio communication in a noisy mining environment is sometimes the only practical and affordable solution to allow communication between miners equipped with personal hearing protection devices. Traditionally, one of the weaknesses of such wireless radio communication lies in the lack of designating receivers: whether they are the intended receiver or not, all those carrying a radio receiver are subjected to the broadcasted signal. The current work will detail a new concept of a "radio-acoustical virtual environment" where the radio signal will only be received by miners within a given spatial range, such range depending on the user?s vocal effort as well as the ambient and perceived background noise levels.

Aug 1, 2013

By Michel Noël

This paper presents a partial compilation of adopted measures of waste rock dump closures at mine sites located in Canada and Alaska, where the climate includes cold winters. The paper also presents the selection process that was followed for some of those mine sites. Mining operations usually generate waste rock that can sometimes result in very large quantities. Additionally, the nature of the ore body and the host rock will often introduce environmental impacts. These impacts need to be managed not only during the operations but also in the long term. Mine closure plans consequently have to address the long term issues that sometimes require perpetual treatment. Closure planning often involves the evaluation of risks associated with environmental and financial liabilities. It needs to consider the science, some common definition of objectives, and there will be a need to manage resources and schedules. Closure planning is essentially an exercise in constrained decision making. A performance and risk based ranking matrix is often developed during this selection process to identify the preferred option(s). The case studies presented in this paper provides a few examples. The level of knowledge on acid rock drainage from waste rock dumps has increased considerably over the past decades. It did not necessarily increase the level of complexity of the adopted closure methods, as the selected closure methods are often kept simple. A common approach consists of stabilising the slopes of the waste rock dumps material by resloping and then covering the waste rock with a growth media to support vegetation. Such covers prevent direct contact of animals with the waste rock material, minimise erosion and reduce infiltration to various degrees. The inclusion of water treatment is obviously dependent on the water quality being released.

Nov 1, 2008

By P. H. Shipway, D. G. McCartney, H. Saghafifar

The microstructural changes during thermal ageing at 650ºC in the interfacial region of Alloy 625 weld overlay on a 2.25Cr-1Mo steel was evaluated. Optical microscopy, scanning electron microscopy in SE and BSE modes, electron probe microanalysis and hardness mapping were used to characterize as-welded microstructure and its changes during thermal ageing and precipitates of interfacial region. Carbon migration across the interface was recognised as a major issue. A region of 300 µm wide adjacent to the fusion line, which was found harder in the as-welded condition decarburized during thermal exposure. Studies revealed that this region transformed to a soft region containing large ferrite grains and micron-sized carbides. In the weld overlay, a 50 µm wide hard band (over 650 Kgf mm-2) adjacent to the fusion line formed and carbide precipitates were observed along grain boundaries. Carbide precipitation mostly occured in the 150 µm wide region close to fusion line.

Jan 1, 2017

By R. M. Berry

A brief outline of refining methods used to (1) upgrade yellowcake to nuclear purity and (2) convert the uranium to the chemical and physical forms required by the fuel fabricators is presented. The uranium hexafluoride (UF6) production facility now under construction at Eldorado, Port Hope, is discussed. Technological improvements in uranium refining are considered.

Jan 1, 1969

By Lassi Klemettinen, Ari Jokilaakso, Dmitry Sukhomlinov, Pekka Taskinen

The solubilities and distributions of molybdenum and iridium in iron silicate slag and copper-iron mattes were studied using an equilibration-quenching technique and subsequent direct phase composition analyses by EPMA (Electron Probe X-ray Microanalysis) and LA-ICP-MS (Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry). The equilibrations were carried out on a wide matte grade interval, ranging from 55 wt-% Cu to 75 wt-% Cu, in pSO2 = 0.1 atm at 1300°C. The results in equilibrium with a solid iridium-molybdenum alloy indicated an iridium solubility of 150–500 ppmw in the sulphide matte, depending on the matte grade, and a molybdenum solubility of 100–600 ppmw. Iridium was distributing predominantly in the sulphide matte with the distribution coefficient of 10+3 - +4 but molybdenum deported predominantly in the slag with Lm/s(Mo) = 0.02–0.1. The effects of alumina and lime additions in the smelting slag were also examined. INTRODUCTION Iridium is a highly siderophile element (HSE), which means that it is incompatible with the sulphide forming elements and possesses a small solubility in mattes, such as copper- and nickel-iron sulphide melts. Molybdenum behaves only modestly in that way (Walker & Li, 2008; Righter et al., 2017). They both are known to be trace elements accompanying copper and nickel sulphide ores. No solubility data, however, are available for them in copper-rich sulphide mattes. Geochemical data on the behaviour of Ir and Mo deal mostly with low-iron silicate systems, e.g. basaltic melts, and high-sulphur sulphide solutions and mattes (Ertel et al., 2008; Fonseca et al., 2007). They also indicate that Ir and Mo dissolve in silicate melts primarily as oxides and not as electrically neutral metal species. Most geological data of iridium focus on high-sulphur systems of the monosulphide composition and typically Fe-Ni mattes where copper is a trace element (Fleet et al., 1996; Sattari et al., 2002). Direct solubility measurements for mattes and iron-lean silicates have also been made using pure Ir or an Ir alloy as the saturation phase (Borisov & Palme, 2000; O’Neill & Eggins, 2002; Makovicky & Karup-Møller, 1999; Ertel et al., 2008; Mungall & Brenan, 2014). A recent summary about the solubilities of HSE’s in iron- and sulphur free silicates is available in Laurenz (2012). The thermodynamics of molybdenum partitioning between oxides and Fe-S-O melts was studied by Mengason et al. (2011). Their results indicate strong accumulation in the iron-rich sulphide in reducing conditions (pO2 = 10-9.6 atm in Ni-NiO equilibrium at 1050°C). Molybdenum dissolves in iron-lean silicate melts as MoO3 species in oxygen pressures above the Fe-FeO equilibrium and as MoO2 in more reducing conditions (Farges et al., 2006; Righter et al., 2017).

Jan 1, 2019

By T. Yalcin, S. Brunet

The flocculant-assisted hydrocyclone involves the addition of a flocculant to the cyclone feed for the purpose of obtaining a clear cyclone overflow, and thereby eliminating or reducing thickener requirements in tailings disposal operations. This paper describes the testing of this concept on the iron ore tailings of Quebec Cartier Mining Company's Mount Wright Concentrator. The current practice at Mount Wright makes use of conventional hydrocyclones and thickeners for the disposal of their tailings, which are generated in a spiral gravity separation circuit. The test work was conducted primarily on their cyclone overflow product which becomes the feed to the thickeners. A detailed study was carried out to determine the sedimentation properties of these tailings in terms of their response to a variety of flocculating reagents, and to varying conditions of pH, pulp density and flocculant dosage. The tailings were then processed in a laboratory hydrocyclone with the aid of flocculants. The use of a shear resistant flocculant, in particular, was found to yield cyclone overflows with low solids contents. Based on the test results obtained, a conceptual flow sheet has been proposed for the treatment of the iron ore tailings at the Mount Wright Concentrator.

Jan 1, 2004

By Ian L. Price

Description of the Springhill Coal Field The Springhill coal basin, which lies in the approximate centre of Cumberland county, Nova Scotia, is of Carboniferous age, and forms a syncline plunging to the westward at an angle of 32° at the outcrop but gradually flattening to the dip. It contains several workable seams of varying thicknesses, a generalized section of the measures in descending order from the surface being: [] The 1,114 feet of strata is composed of shales and sandstones, and all of the coal seams mentioned, with the exception of No. 4 and No. 5, have been mined commercially. The coal is said to be the best steam and domestic coal in the Province of Nova Scotia.

Jan 1, 1946