Search Documents

By Turgut Yalcin

"In this study, potential benefits of focculant usage were explored in the processing of mill tailings by hydrocyclones. Tests conducted on copper-nickel mill tailings have demonstrated that, under suitable conditions, flocculation could significantly enhance solid-liquid separation in hydrocyclones. For example, at a feed pulp density of approximately 9%, focculant-assisted hydrocyclone produced an underflow with over 98% solids recovery, compared to a recovery of less than 53% with conventional hydrocyclone. However, feed pulp density was found to be a critical factor, and tailings with pulp densities of greater than about 15%required a two-stage hydrocyclone operation where the focculant-assisted hydrocyclone was employed at the second stage to process the overfow of a conventional hydrocyclone.The underflow and overflow products obtained from the focculant-assisted hydrocy-clone may be discharged into tailings dams in the same manner as those produced by gravity thickeners. The focculant-assisted hydrocy-clone would, however, provide a higher throughput."

Jan 1, 1996

By L. C. Galloway, G. L. Tiley

"Mine hoist brakes must meet the following statutory performance criteria:- There should be two independent braking systems; at least one should act directly on the hoist drum.-If one brake fail s, the others should be able to retard and stop the hoist safely before the descending conveyance, carrying the rated load, reaches any obstruction.- When all brakes apply, decelerations should not be so violent that men travelling in the conveyance are injured.- The brakes shall not overheat and fade during an emergency stop.This paper discusses design principles and capacities of caliper and disc type brakes, when applied to double drum and friction hoists of equivalent capacity.IntroductionThis paper is about the brakes that are used on mine hoists; their functions, especially in emergencies, typical design, and how they are operated, controlled, tested, and adjusted.There are two basic types of mine hoists:1. Drum hoists, where the ropes are attached to, and coil on drums. The simplest system has only one drum. Most such hoists, however, have two drums, attached to a common shaft. Ropes are wound on each drum in opposite directions, so that when one conveyance is being raised, the other is lowered. The conveynaces may travel in vertical or inclined shafts. In the latter case, the hoist s are referred to as slope hoists.2. Friction hoist s, where the headropes are not attached to the wheel, but are in contact with it for an angle of lap of, typically, between 180 and 195 degree s. Forces are transmitted from the hoist wheel to the head ropes by friction.The lower ends of the conveyances are connected to balance ropes , approximately the same weight per foot as the headropes."

Jan 1, 1986

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By Robin N. Adair

The Halfmile Lake stratiform volcanogenic massive-sulfide deposit consists of pyrrhotiterich breccia-matrix sulfides and pyrite-pyrrhotite-rich layered sulfides that form a laterally continuous sheet stratigraphically underlain by an extensive pyrrhotite-chalcopyrite-quartz stringer zone. Mineralization is hosted by a sequence of felsic pyroclastics and volcanic-derived, fine-grained metasediments. The proportion of volcanic to sedimentary rocks indicates increasing vent proximity from southwest to northeast across the deposit area. Fine- to medium-grained felsic pyroclastics and roughly equal amounts of fine-grained metasediments comprise the stratigraphic footwall to the mineralization. Quartz-feldspar porphyritic bodies cut this sequence and may have provided the heat source for exhalite activity. Felsic tuffs, locally crystal-rich, and lesser amounts of metasedimentary rocks make up the immediate stratigraphic hanging wall. This sequence is stratigraphically overlain and locally interfmgered with mafic volcanics that contain substantial proportions of felsic fragments. Deposition of sulfides post-dated the beginning of felsic volcanism, which places the deposit in the middle of the Lower Tetagouche Group. Compositions of the volcanic rocks range from basalt to rhyolite and exhibit sub-alkaline affinities. Strongly overprinted whole-rock, trace-element, and REE geochemical signatures resulting from mineralizing hydrothermal activity confirm the genetic relationship between the stringer zone and the mineralized sheet. Large-scale D1 folding has overturned the entire sequence. D1 thrust faults and related sheath-like folds have profoundly affected sulfide distribution. D2 is manifested by a penetrative S2 foliation, and D3 is represented by large-scale open folds.

Jan 1, 1992

By H. Son

The three-dimensional (3D) reconstruction of as-built industrial plant models plays an important role in revamping planning, maintenance planning, and preparation for dismantling during the lifecycle of industrial plants. Recently, the 3D reconstruction of existing industrial plants was conducted using laserscan data to make surveying processes more efficient. However, the current 3D reconstruction process from laser-scan data is still limited due to the need for significant human assistance. Although a great deal of effort has been made to efficiently reconstruct 3D as-built industrial plant models, the presence of objects?such as equipment, pipelines, and valves of different sizes and shapes?in existing industrial plants significantly increases the complexity of laser-scan data and makes automating the reconstruction process more challenging in practice. The purpose of this study is to propose a knowledge-based approach for the 3D reconstruction of as-built industrial plant models from unstructured laser-scan data. First, pipelines were extracted from laser-scan data based on surface curvature information and knowledge about pipelines' sizes from existing piping and instrumentation diagrams (P&ID). Once entire pipelines were extracted, they were modeled based on skeleton features. Then, the remaining objects were clustered and grouped separately via the region grouping process. Afterward, clustered objects were retrieved and modeled based on global feature-based matching from the 3D database. Finally, the resulting model was checked to ensure that it was well-reconstructed according to the information regarding the relationships among objects abstracted from the existing P&ID. The preliminary results on actual industrial plants show that integrating knowledge into the reconstruction steps played an important role in the proposed approach and that this approach obtained accurate as-built industrial plant models from unstructured laser-scan data. The proposed approach could be successfully utilized to assist in many applications during the lifecycle of industrial plants.

Aug 1, 2013

By Frederic Benard

THE Ontario Refining Company, Limited, wholly-owned subsidiary of The International Nickel Company of Canada, refines the entire blister copper output of the latter's Copper Cliff smelter. Prior to 1936, the blister was cast in 460-lb. cakes at the smelter, loaded on open cars, and transported by rail to the refinery, a distance of approximately 1 1/4 miles. Here the cakes were transferred to the plant narrow-gauge system, charged to furnaces, and re-melted. This procedure necessitated the operation of holding furnaces and casting machines at the smelter -extensive re-handling-and melting down of a cold charge at the refinery. Transfer of the copper in molten form direct from converters to anode furnaces promised a considerable reduction in costs, and this possibility was investigated. As a result, a portable holding furnace, or hot-metal car, was designed and constructed. It was placed in operation in July, 1936, to be followed a year later by three additional units of slightly modified design. Figure 1 shows the original car, and Figure 2 the lacer type. With four cars in service, operations were placed on an all 'hot-metal' basis.

Jan 1, 1938

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011

By G. R. Tostengard

"The paper identifies functional areas which frequently can yield significant productivity improvement. Emphasis is placed on the repair and maintenance, material supply and training functions. Successful approaches are discussed in some detail, and typical results which have been achieved are reviewed.IntroductionA challenge which at all times confronts the manager o f any mineral operation is the potential to improve his operation no matter how effective it might be a t the present time. The challenge has been present through my entire lifetime and I suspect a good many years prior to that and, I expect, will continue many year s and decades in the future. The competitive and economic situation in which we in the minerals industry find ourselves today makes the challenge eve n more important during the 1980s. In many cases it’s a question of survival, not simply pr of it improvement.There are, of course, many avenues to improving profitability; technological changes, new equipment and facilities, improved products, improved mine plans, etc. All of these are important and must be addressed by each manager. This paper focusses on just one avenue to improvement and that is ""improved management"", not so much of management at the boardroom level but of improved management o f the facilities and workforce as the y currently exist. Management implies control. There are three areas where control is often found lacking:1, Repair and maintenance of equipment and facilities;2. Material supply including procurement, inventory control and warehousing; and3. Training.These three areas are all complex and difficult to manage and they are all but ignored in the formal education which our industry's manager s normally receive. They are areas which can be improved with relatively small investments and therefore, they represent especially attractive improvement targets during the 80s when, for most of us, investment dollars are very difficult to come by."

Jan 1, 1983

By M. Alvarez-Silva, A. Uribe-Salas, J. A. Finch, M. Mimezami

The point of zero charge (PZC) of electrokinetically anisotropic minerals (chlorite and serpentine) was determined using the Mular-Roberts (M-R) titration technique, and compared to isoelectric point (IEP) obtained from electrophoretic mobility measurements. To validate the M-R technique, the point of zero charge and isoelectric point of two isotropic minerals (alumina and silica) were shown to be comparable. For serpentine and chlorite, respectively the PZC was found at pH 4.3 and 4.6, while the IEP occurred at pH 3.2 and <3. Settling tests showed that the maximum settling rate, which corresponds to aggregated particles, for chlorite was around pH 3, i.e., close to the IEP; lizardite did not show a conclusive maximum.

Jan 1, 2009

We describe a new method of characterising the effect of dissolved materials on the rate of coalescence of bubbles in aqueous media. Single bubbles were allowed to rise to meet the surface of an aqueous solution, and the time of persistence between arrival and bursting of bubble was measured as a function of solute concentration. A laser beam was placed just above the surface of the liquid, with a detector in the light path, so that any disturbance at the surface could be seen as a break in the beam. The arrival of a bubble at the surface could be detected from the behaviour of the trace on an oscilloscope, and when the bubble broke, another significant change in the signal could easily be seen. The time between disruptions was reported as the persistence time. The effect of a homologous series of n-alcohols (C1 to C8) on the persistence time was measured, in aqueous solution. It was found that with increasing concentration of a particular solute, the persistence time increased up to a point, and then declined. However the magnitude of the persistence time was found to increase with increasing numbers of carbon atoms in the molecule. Bubbles of 1, 2 and 3 mm diameter were used. Persistence time increased with increasing bubble diameter, the maximum values observed being of order 100 secs. For a given solute, the persistence (drainage) time increased with increasing bubble diameter. The concentration Cmax at which the maximum persistence time was observed, was found to be independent of the bubble size. It decreased uniformly as the carbon number increased, and was well correlated by the function y1/2 (dy /dc) -2 I dc)-2 . There was no apparent correlation with the surface excess at maximum persistence time.

Jan 1, 2006

By A. O. Orumwense

Mill circumferential speed, the number of passes of pulp through the grinding chamber, media type, size and filling ratio were investigated in an attempt to determine how to effectively grind copper concentrates in a stirred mill. The stirred mill product fineness was enhanced to some extent by decreasing media size, high media filling, and an increased number of passes of the pulp through the grinding chamber. Shape also plays a major role in grinding media effectiveness, with spherically shaped media producing a finer size. The fineness of the product increases with increasing power consumption but the method of energy transfer is very important in energy utilization. The effect of the mill parameters on copper flotation was evaluated. Copper recovery was influenced by grinding media size, mill speed and the number of pulp passes through the grinding chamber.

Jan 1, 2006

This paper describes basic parameters, such as surface forces and film elasticity, affecting the stability of foams (two-phase froths). We used the thin film pressure balance (TFPB) technique to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG). The results were compared with the foam stabilities measured experimentally and the film elasticities calculated using a new model developed by Wang and Yoon (2006). It was found that at low electrolyte (NaCI) concentrations foam stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother type and concentration. Further, the kinetics of film thinning was studied at a high electrolyte concentration. The results obtained in the present work showed that the major role of a frother is to decrease the hydrophobic force rather than to increase the film elasticity. This conclusion is drawn from the observation that at the typical frother (MIBC) concentrations employed in flotation, frother additions cause sharp decreases in hydrophobic force while causing relatively little changes in film elasticity.

Jan 1, 2006

By E. A. Haack, L. A. Warren

Microbial biofilms are essentially biologically driven, geochemically reactive interfaces between solid surfaces and aqueous solution. Field investigation of acid rock drainage (ARD) associated biofilms at the Onaping nickel mine (Onaping, ON, Falconbridge Ltd.) characterizing: (1) micro-geochemical gradients (pH and 02) (2) metal fractionation amongst biofilm solid components, and (3) microbial communities; over both seasonal and diel timescales, indicates biofilms are highly metal reactive. Results show that biofilms accumulate metals seasonally within two microbially controlled solid fractions: amorphous hydrous manganese oxide (HMO) biominerals and the organic biofilm matrix. The biofilm geochemical microenvironment, driven largely by microbial activity, dynamically impacts biofilm metal behaviour over diel timescales. These results indicate that microbes can play significant roles in bulk system reactive metal transport. On-going investigation seeks to characterize the microbial players and the microbial-geochemical linkages involved in Mn oxyhydroxide formation and subsequent metal sequestration, with the goal of engineering this microbial activity as a bioremediative approach. This approach will have utility beyond specific application to the Falconbridge Onaping site to ARD mine environments in general, as the likely microbes involved in these processes are typically common across ARD systems.

Jan 1, 2004

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By Raj K. Rajamani, Nikhil Dhawan

"Agglomeration has become common pre-treatment step to improve heap leach percolation thereby recovery, the fundamental understanding of the agglomeration process for crushed ores is still lacking. Agglomeration is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing. Numerous experiments have been carried out in laboratory scale batch drums using different ores. It has been found out that experimental agglomerate size distributions exhibit self-preserving spectra. The self-preserving/ similarity distribution of the agglomerates is found to be independent of operating conditions and is uniquely determined by the size enlargement mechanism. An empirical model based on the absolute difference between moisture applied and optimum moisture was developed. This model uses self-preserving spectra in the form of a Rosin-Rammler distribution function to predict size distribution at different operating conditions. The empirical model was considerably easier to work with plant scale agglomeration drums. Also, a test known as dip test is developed which improves fundamental understanding of the agglomerate formation and growth mechanisms. This test also provides the progeny size distribution of each agglomerate size. The progeny size distribution was analyzed with a model that partitions the particles into a host and guest category. The ensuing partition coefficient identifies the behaviour of a particle as a host for other particles or a guest layering on other particles. This concept helps in identifying the type of agglomerate that would result for a specific feed size distribution. INTRODUCTIONHeap leaching is one of the hydrometallurgical processes that have served as a green and economically viable process for the treatment of low grade complex ores of copper, uranium, nickel, silver and gold (Dhawan et al., 2013). Heap leaching appears to be a favorable candidate for the least energy consuming process for low grade ores. In heap leach operations nowadays a pretreatment step known as crushed ore agglomeration has been implemented (Dhawan et al., 2013). A bed of agglomerates improves the uniform percolation of solution through the heaps of ore. Therefore, it was possible to treat wastes and mill tailings via agglomeration and heap leaching. Agglomeration pretreatment is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing (Bouffard, 2005; Dhawan et al., 2013).While agglomeration has become common practice pretreatment step in heap leach operations, the fundamental understanding of the crushed ore agglomeration process is still lacking. The author reviewed publications up to 2012 on the crushed ore agglomeration process and did not come up with modeling studies on the topic (Dhawan et al., 2013). Some of the possible reasons can be the stochastic nature of the process, experimental difficulties, and lack of instrumentation for fundamental studies."

Jan 1, 2016

By Thomas Kilpatrick

The liability created by building this railway is the great financial problem before the people of British Columbia at the present time. In dealing with the subject, I propose to divide it into three periods: The Past - The Present - and The Future. The Past The primary objects in building the railway were to provide an independent and direct route for the Grand Trunk Pacific railway into the city of Vancouver, and to open the central and north-eastern portion of the province.. This vast territory, almost one-half the entire area of British Columbia, has great wealth in fruit, agricultural, and grazing lands; timber, coal, water-power and minerals of all kinds, including some of the richest placer deposits in the world. Rivers and lakes teem with fish. Big game, including moose, elk, caribou, deer, grizzly and black bear, mountain goat and sheep, is plentiful and there is an abundance of small game and fur-bearing animals. In addition, its scenic attractions are unsurpassed in Canada. To develop these resources it was considered necessary to build a railway from south to north as a main artery of transportation and, if necessary, branch lines to carry heavy .shipments of coal or other commodities. Lighter freight may be handled by motor trucks from distant points to the railway.

Jan 1, 1925

By A. David MacPhail

"Highland Valley Copper is a large volume producer of copper and molybdenum concentrates. Production is by conventional truck and shovel operation combined with an extensive ore handling in-pit crushing and conveying system.Grade of the two orebodies is low at 0.4% copper and 0.007% molybdenum and this demands a production rate in excess of 260 000 tpd at a stripping ratio of 1: 1. Mining cost has to be kept at minimum levels to keep the mine profitable and thus, it is necessary to keep in the forefront: of technology. As well as the in-pit crushing system, the mine has pioneered the use of shovel weighing coupled with a state-of-the-art dispatch system.Maintenance of the equipment is carried out at the on-site mine maintenance shop with assistance from local shops for engine and wheel motor rebuilds and other large jobs such as those requiring stress relieving. Shovel and truck rebuilds are undertaken by mine crews. Both long- and short-term planning is designed and scheduled in the mine engineering section. Outside consultants are used to assist in slope design, reclamation and blasting technology."

Jan 1, 1992

By H. Karakul

Determination of P-wave velocity (Vp), which is closely related to intact rock, is a nondestructive, easy and less complicated procedure. Due to these advantages, there is an increasing trend to predict the geomechanical properties of rocks from Vp. In addition to mineral content, cementing material and porosity, degree of saturation (Sr) are also other factors influencing geomechanical properties of the intact rock. However, up to the present, in the studies on the prediction of geomechanical properties of rocks from Vp, the effect of Sr has not been investigated. By considering this issue, in this study, it was aimed to correlate strength properties (uniaxial compressive and tensile strengths) and Young’s modulus with Vp of various rock types under different degrees of saturation. In addition, geomechanical properties of rocks were estimated from theoretical P- and S-wave (Vs) velocities, which were calculated based on their mineralogical compositions. For this purpose, fourteen different rock types were collected from several parts of Turkey and a comprehensive laboratory testing program was conducted. In the statistical analyzes, a series of different prediction relationships were developed by using independent variables such as Vp, Sr and effective clay content (ECC). Simple regression analysis results indicated that although prediction of the geomechanical properties of rocks from Vp at different degrees of saturation was possible, the equations developed would yield some under- or over-predictions. On the other hand, the multivariate equations developed have very high prediction performances and are very useful tools to estimate the geomechanical properties from the measured Vp at any Sr value. In addition to mineralogy, the variation in geomechanical properties with increasing Sr is also associated with the combined effect of porosity and clay content, which is first described in this study by the term Effective Clay Content (ECC). It is also noted that strength properties of rocks at any Sr may also be estimated using the empirical relations based on the theoretical Vp and shear-wave velocity (Vs) values, which are calculated from their mineralogical compositions.

Jan 1, 2015

By Y. M. Shneerson, V. M/ Shpaer, E. E. Zhmarin, A. Y. Lapin, E. M. Vigdorchik

This paper describes studies of zinc concentrate oxidizing pressure leaching using the method of mathematical modeling. The concept of a kinetic function was taken as a basis for mathematical modeling of the leaching process. The kinetic function describes dependence of the unreacted component share OJ on the relative time x (the relative time is the ratio of the test duration and the time of complete dissolution). This kinetic function is determined in accordance with the results of batch laboratory tests. The laboratory tests have been carried out on zinc concentrate produced from Kazakhstan zinc-copper ores. Zinc concentrate consisted mainly of three types of minerals: sphalerite (70%), pyrite (13%) and chalcopyrite (10%). Oxidation reactions of sphalerite, pyrite and chalcopyrite have been considered as principal ones. The kinetic characteristics of the process (kinetic function, reaction order, activation energy, duration of complete dissolution of the concentrate components) have been calculated in the course of laboratory tests. The mathematical model was used for estimation of the main technological leaching process parameters (such as process rate, degree of metals extraction, autoclave capacity, heat balance, etc.). Mathematical modeling based on the kinetic function concept allows safe designing of metallurgical equipment and scaling the technology to industrial capacity.

Jan 1, 2004

By Dave M. Jakelski, Gerhard W. Heinrich, Peter F. Wells, Daniel F. Suarez, Jamie B. Beauchamp

"A need for increased copper concentrate production and for less nickel contamination in that concentrate at Falconbridge's Strathcona Concentrator during 1993 required the installation of a third flotation column and improvements in the operation of the existing circuit. Innovations in wash water distributor and launder design were fundamental in achieving objectives on a new 3 meter diameter column. Minnovex plug-type spargers were tested on a 2.1 meter diameter column in order to reduce maintenance requirements. The paper details the measures taken to enhance column flotation circuit performance and the results obtained.IntroductionFalconbridge's Strathcona Mill receives 10% of the ore feed from a rich copper zone in the Strathcona mine. This ore typically grades 7% copper and 1 % nickel and, because of its high copper content, it is processed in a separate circuit ('C' circuit) which consists of conventional grinding, rougher flotation with the concentrate being treated with lime to pH 12.3 and cyanide followed by column flotation. The columns are operated with mechanical flotation scavengers and the scavenger concentrate is returned to the column feed. Testwork conducted in 1991 showed that the original flotation column (Column 2) could only produce 5.5 mtph of concentrate with less than 0.5% nickel (Figure 1).Between 1991 and spring of 1993, production was increased at times by open circuiting the scavengers. Metallurgical improvements were obtained by improving the wash water distributor of Column 2 and by wash water sprays in conventional cells (1 ). However, the scavenger concentrate assayed 0. 7 -0.8% nickel and was not acceptable for long term operation. When Copper ore production targets were significantly increased for 1993, it became clear that an additional flotation column was required. The new flowsheet employs mechanical scavenger cells on the column tails as in Column 2 circuit (Figure 2). A -parallel configuration was chosen as pulp solids fraction has been shown to be a critical variable and the second column in series would receive a lower density feed."

Jan 1, 1994