Search Documents

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By Y. G. Seredkin, A. A. Vasiliev, A. Y. Senchenko, A. V. Aksenov

"Autoclave oxidation, bacterial and chemical liberation, roasting, acid oxygen processes, atmospheric oxidation prior to cyanidation are applied to process refractory sulphide concentrates. It is obvious that the processes with the maximum effect regarding gold recovery are those in which complete destruction of sulphides takes place and gold becomes accessible for further cyanidation through liberation from sulphide “capsula”. But the significant recovery increase is often accompanied by a process complexity, high expenses for equipment purchase and maintenance. It makes material processing costinefficient. Process optimization has led to progress in ultrafine grinding, bacterial and autoclave oxidation processes. In our opinion sulphide atmospheric oxidation processes are the most interesting as oxidation there runs without high temperature (up to 100°?) and excess pressure (open units), and with acid environment close to neutral. The process of sulphide concentrates treatment named “Albion” (Albion Process™) represents a combination of ultrafine grinding and oxygen oxidation without pressure and external heating. The process has a number of advantages: sodium cyanide consumption decrease during gold leaching and high ecological compatibility. TOMS institute in collaboration with Glencore Technology Pty ltd (Australia) tested Albion technology aiming at liberation of finely disseminated gold from flotation concentrate produced from refractory ore of one Russian deposit. The testing has shown that Albion technology makes it possible to process refractory products with quite small capital investments. It enables involving medium and small refractory gold deposits into processing.INTRODUCTIONThe considerable part of the world Au-bearing reserves is present by refractory ores with finely disseminated gold. Gold in such ores is often associated with sulphide minerals and locked in so called “sulphide capsula” since it is closed inside dense sulphide grains and inaccessible to recovery by cyanidation. To treat refractory sulphide concentrates containing gold a number of processes were developed and they can be divided into three groups (Figure 1)."

Jan 1, 2016

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By M. N. Vu, G. Armand, A. Noiret, D. Seyedi

Extensive experimental observations have been performed around drifts and shafts at the Meuse Haute-Marne (North-Eastern France) Underground Research Laboratory (URL) to assess the extent and pattern of the induced fracture networks in Callovo-Oxfordian claystone. Two types of fractures can be distinguished, namely; shear (mode II) and extension unloading (mode I) fractures. The main goal of the present paper is to provide insights on the extent of damaged zone around the drifts by numerical simulations. A two-step approach is considered. First, 2D elastic calculations are performed for simulating the excavation of a drift following the direction of the major in situ horizontal stress. The evolution of the stress and strain tensors around drifts are calculated by applying an elliptic convergence function on the drift wall. Two failure criteria are then verified for the induced damage. An equivalent strain and an elastic energy based damage criteria are considered. The obtained results show that the employed simplified approach provides rather good results for the extent of the damaged zone for drifts parallel to major horizontal stress. However, post-processing elastic results leads to overestimating the vertical extent of the damage zone and underestimating its lateral extent, where the in situ stress state is quasi-isotropic in a section of drift. Nevertheless, the obtained results show that an energy based damage criterion could be considered as a potential way for reproducing the extent of the damaged zones if a convergence function can be defined for the drift.

Jan 1, 2015

By George S. Martin, Michael D. Winship

"Placer Dome Inc. is the operator of the Musselwhite project located 100km north of Pickle Lake, Ontario. J.S. Redpath Limited was contracted to conduct an underground exploration program using shaft access.During the winter of1988, the shaft collar was established in 16 metres of water bearing sand and till overburden. This paper will illustrates the engineering techniques used to overcome the obstacles to installing a shaft collar in deep overburden. Specialized dewatering and piling procedures were employed.INTRODUCTIONHarold and Allan Musselwhite discovered gold in the Opapimiskan Lake area, north of Pickle Lake, in 1962. The prospectors were grubstaked by ten companies in 1973.A diamond drill program was initiated shortly thereafter.In 1983an underground ramp exploration program was carried out on the West Anticline portion of the property. The program was unsuccessful in establishing an ore reserve so surface exploration continued. In 1986the ""T"" zone was discovered. Further surface drilling was done and an over-all drill-indicated reserve of 6 million tonnes at 7 grams per tonne was outlined. The gold mineralization occurs in several vertical tabular deposits within the iron formation. In late 1987the joint venture partnership, now consisting of Placer Dome Inc., Inco Gold Co., Corona Corporation and Esso Minerals Canada, contracted J.S. Redpath Limited to conduct an underground exploration program on the ""T"" Zone.The scope of work for the project was to: 1. establish a 45 km winter road in 1988 and 1989;"

Jan 1, 1989

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By K. Hashiba, Y. Z. Liang, K. Fukui, M. Koizumi

"Efficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Development and modification of the rock drills based on test data are timeconsuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved. The objective of our research project is to construct a new realistic numerical model of continuous percussive drilling, which is based on the previous Okubo-Nishimatsu’s model. In this study, the parts of the previous model involved in stress wave propagation and attenuation were modified. The two models were prepared for HD712 hydraulic rock drill mounted on crawler drills and HD210 hydraulic rock drill mounted on drilling jumbos. Stress wave propagation was computed with the discretized one-dimensional wave equation. The calculated results were compared to the stress waves measured on a rod during percussive drilling. In both models for HD712 and HD210, the measured stress waves can be reproduced with the one-dimensional model of the same acoustic impedance as the actual piston, shank rod and rod combined with the CI+spring model as a rod joint. The calculated results indicate that the spring constant in the model of a rod joint needs to be set appropriately depending on drilling conditions. INTRODUCTIONEfficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Components related to the percussive drilling are a drill body, a piston, a shank rod, rods, rod joints, a bit and rock. The piston in the drill body is reciprocated by hydraulic pressure and collides with the shank rod a few thousand times per minute. Stress waves generated by the collision propagate and attenuate in the rods and rod joints, and then reach the bit. The bit penetrates and crushes rock. During percussive drilling, the components mutually affect each other and self-induced oscillation occurs. The number of blows and the rate of penetration are determined by the practical drilling conditions such as hydraulic pressure, thrust force, number of rods and mechanical properties of rock. Development and modification of the rock drills based on test data are time-consuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved."

Jan 1, 2015

By D W. MacFadgen

THE operating advantages of the longwall retreating system of mining, as opposed to longwall advancing, have been well known for many years. Although retreat walls have been successfully worked in the past in some of the collieries of the Dominion Steel and Coal Corporation in the Sydney, Picton and Cumberland areas, the adoption of longwaIl retreating as the general sys-tem of mining has not been attractive in the Sydney field, due to the time and expenditures required to drive roadways to the boundary. In addition. difficulties in maintaining effective ventilation on the faces, especially under conditions of low barometer, have made the operators in the field hesitant to adopt this as the general system of mining. The development of a machine capable of rapid entry drivage has made possible the driving of the necessary road ways to the boundary at a moderate cost, completely changing the picture and making a retreat system more attractive.

Jan 1, 1961

By Mengsu Hu, Yuan Wang, Jonny Rutqvist

Material interfaces and typical boundary conditions are boundaries influencing the existence, uniqueness and stability of numerical solutions of water flow in heterogeneous media. The Numerical Manifold Method (NMM) with a two-cover-meshing system is an ideal method to handle boundaries, considering its flexibility with no need to adjust mathematical nodes onto boundaries, the meshing efficiency, and its integration precision. In this study, we derive and compare two new approaches for boundary constraints, i.e., a discontinuous approach with Lagrange multiplier and a continuous approach with jump function in the frame of NMM. In the discontinuous Lagrange multiplier method (LMM), Dirichlet boundaries or the material interfaces are regarded as discontinuities which are linked by Lagrange multipliers. In the continuous Jump function method (JFM), the material interfaces are regarded as inner interfaces, where the refraction law is realized by constructing jump terms with discontinuity of hydraulic gradient in its normal direction. Both the continuous and discontinuous approaches make full use of the aforementioned advantages of NMM and are established based on a clear physical meaning of water flow by our energy-work seepage model. The newly derived boundary-constraint approaches were coded into an NMM water flow model and tested for precision and efficiency on different simulation examples. We first tested both LMM and JFM for an idealized heterogeneous model, comparing the numerical results with analytical solutions. Then we tested both approaches with a heterogeneous model and compared the results of hydraulic head and specific discharge. We proved that both approaches are very suitable for material boundaries considering the accurate realization of the boundary constraints and the flexibility with no need for mesh-conforming.

Jan 1, 2015

By H. A. ?ye

The ISO TC 226 (Materials for the production of primary aluminium) has presently issued more than one hundred standards on the materials: alumina, pitch, petroleum coke, carbon anodes, carbon cathodes, ramming paste, fluorides and refractory). The object of the standardization work is to find methods that both material producers and smelters will accept. Methods that are specific for the operational conditions have been developed in addition to more traditional room temperature methods. Examples of important properties under operational conditions are: Air and C02 reactivity of anodes, Equivalent temperature for baked anodes, Sodium expansion of cathode blocks, Shrinkage and Rammability of paste, Penetration of electrolyte into refractories.

Jan 1, 2006

By William Skinner, Jim Pae Lem, Massimiano Zanin

It is well known that the specific density of minerals has adverse influence on the classification performance of a hydrocyclone, particularly when liberated high density minerals such as gold or uranium are present in sulphide ores. These liberated heavy minerals often misreport to the underflow and recirculate to the system. Such phenomena does result in serious issues in a closed-grinding circuit, such as overgrinding, leading to production of flaky particles (as in gold) or ultrafines, in addition to increased energy inefficiency. In plants which present gold liberated at coarser size, loss of gold due to cyclone inefficiency is sometimes prevented by incorporating gravity concentrators into the grinding circuit to recover the gold. The work reported in this paper looks at whether the effect of density will prevent successful rejection of liberated U-bearing minerals in the –10µm size range of a plant re-cleaner feed, which is necessary to minimize penalty U accumulation in a copper concentrator. The study was carried out using a cyclone rig with spigot diameter of 0.25 inches in combination with batch flotation. It was found that the density effect is almost negligible at particle sizes below 10µm. Consequently, the liberated U-bearing particles finer than 10 µm were successfully removed in the overflow stream as rejects and hence U grade in the copper concentrate remarkably reduced, by 16 ppm. Based on the results, de-sliming of the re-cleaner feed was recommended for plant trial and implementation.

Jan 1, 2016

By E. A. Rychkun

"For the last 700years of recorded economic history, man has been subjected to alternating inflationary and deflationary patterns. Through this period of time, a severe deflationary pattern has developed approximately every 55 years, creating 12recordable occurrences. Through the last two centuries, this severe deflationary phenomenon has come to be known as a depression. As these depressions have repeated themselves regularly, they are cyclic. This in turn leads to the question of whether the 13th cycle will also repeat itself in the form of a depression. As this cycle is now 51 years old, we must consider the possibility at about 1984.In analyzing a 700-year record of consumer prices in Southern England, the 55-year cycle appears to vary in shape and intensity. This varying phenomenon is due to the effect of longer cycles upon which each one ""rides "". Because each cycle effectively rides on the next largest, which in turn rides on the next largest and so on, the combined measured effect of all cycles together at any point in time is always unique. This means that anyone cycle can never repeat itself in an exact identical manner. The combined effect therefore is what we observe in the form of prices and, as cycles interact, variations in deflation are produced . The ""science"" of economics attempts to quantify and develop theory on situations which are never identical and hence can be conservatively classified as a useless predictive tool.This means that more unconventional approaches may be required to predict our economic future. In looking at previous depression cycles, it is possible to recognize similarities in human behaviour patterns and hence the resulting economic movements. These behaviour patterns create major events or influencing factors which set the scene for a major deflationary condition. The way in which these factors occur, however, is not predictable. As more and more of these similar events are identified in each cycle, we can increase our confidence on the probability of the last event occurring (a depression). By also unravelling the set of larger cycles, we can determine the potential combined effect at any point in the future.This paper presents a system of cycles ranging from 800 years to 3 years which appear to operate in our economic system. By so doing, a long-term projection into the next century can be made. Finally, the paper deals with the main controlling similarities within the depression cycle, to show that a comparison with our current cycle implies that a major deflationary collapse in the mid 1980's is virtualy inevitable."

Jan 1, 1980

By A. D. Hunter, J. M. JR. Moore

"The Aldermac deposit and associated prospects occur in the Noranda Archean volcanic centre of the Abitibi greenstone belt. Over two million tons of are grading 1.65% copper, with minor gold and silver, were mined between 1933 and 1943. The deposit has features in common with the Vauze and Millenbach mines in the same district.Recent detailed mapping, geochemistry and petrography combined with data from former diamond drilling and mining operations permit a re-interpretation of the Aldermac area. The orebodies and spatially related sulphidic zones are con eluded to be volcanogenic.The host rocks are a chemically bimodal suite of mafic and rhyolitic flows, volcaniclastics and related subvolcanic intrusions. Massive sulphide lenses are spatially related to a quartz-feldspar- phyric rhyolite dome and siliceous, volcanic-exhalative sedimentary rocks, The succession is cut by gabbro and syenite, related to later stages of volcanism, and by post Kenoran diabase dykes. Regional metamorphism attained the low greenschist facies, but the rocks lack penetrative deformation.Hydrothermal alteration is primarily an intense silicification of mafic volcanic rock s enveloping, or lying below, sulphidic zones. Chlorite and sericite alteration zones, including dalmatianite, are more locally developed and have a closer spatial relation to mineralization, as do epidote, calcite and calcic garnet.The structure is complex and cannot be explained by isoclinals folding; rather it reflects concurrent faulting, and extrusive and intrusive activity. Fault blocks were rotated and exhibit opposed facing; the original selling was possibly a submarine graben.Sulphidic zones occur within mafic and felsic volcanic rocks and at the interface between the two; there is thus potential for discovery throughout the known stratigraphic succession. Exploration conducted according to a volcanogenic model is advisable, particularly in the light of recent discoveries in similar rocks of the Amulet area."

Jan 1, 1983

By R. A. Ford

The paper outlines: methods used for the determination of wear metals in motor and transmission oils; contaminents in motor, transmission and crusher lubricating oils; and viscosity determinations. Case histories and costs are presented to illustrate the value of an oil analysis program. Introduction NORANDA MINES LIMITED (BELL COPPER DIVISION) is located on the shores of Babine Lake, approximately 450 miles north of Vancouver, British Columbia. Access to the mine is by road from Topley, B.C., about 40 miles away. When a preventive maintenance analysis program was first considered, it was obvious that if samples were to be sent out for analysis, results would not be available for at least a week, due to the distance from any commercial laboratory. The assay laboratory was asked to investigate the possibility of determining wear metals on site. A limited program was started soon after production commenced, and this has now grown to include all large mobile equipment as well as crushers and grinding mills. The laboratory also now determines viscosity, fuel dilution, dirt and abrasives, glycol and water. All these results are ready within two days. This paper will outline the methods used, data interpretation, several case histories and the benefits from such a program.

Jan 1, 1977

By Muhammad Zaka Emad

Cemented rockfill (CRF) is a mixture of rock aggregate and binder slurry. It is a stiff backfill, it is fast curing, its operation is simple, placement rate is reasonably high and no drainage is required. The main demerit of CRF is failure of exposed faces causing ore dilution, which can be associated with the fill placement method. This paper discusses the effects of two placement methods being practiced by mines and numerical modelling is used as a tool to evaluate stability of the backfill column. In the first method, practiced in longitudinal retreat mining of a narrow vein deposit, the rockfill is hauled and dumped into the stope with a LHD scooptram. Once dumped, cement slurry is sprayed into the stope. In the second method, a raise situated centrally above the mined stope is used to convey already mixed CRF into the stope. Stopes are mined out transversely in primary and secondary blocks in a sublevel stoping system. Problems of poor mixing in combination with both placement methods are discussed. The two backfill placement methods are analyzed for blast induced vibration damage using the dynamic Flac3D modelling technique accounting for rock mass and fill damping characteristics, and a pressure wave is used to simulate the blast vibrations. Fill heterogeneity has also been considered for the two cases and results are compared.

Jun 1, 2012

By Claudia Gasparrini

"The ore microscope and electron microprobe, two common instruments for academic research, have not been used to full advantage in the Canadian mining industry, perhaps because they are not readily available to most mining companies.The present paper gives a description of the two instruments and of the manner in which, when used together, they contribute to the identification and description of mineralogical and metallurgical samples, and reviews the applications, to . date, in the mineral industry.The metallurgical applications can assist in determining the best separation technique for a particular metal or other economically important element, can provide explanations for poor recovery and/or liberation, can be used to determine theoptimum concentrate grade and can indicate environmental problems that may arise from the extraction process.In certain cases, the use of the two instruments may assist in the evaluation of new mineral deposits and in the determination of the origin of mineralization.IntroductionThe ore microscope and electron microprobe, two widely used instruments in universities and other research institutions, have not been exploited to their full potential by the Canadian mining industry.High-magnification, high-resolution ore microscopes, owned by most Canadian universities and government mining branches, are not widely used by mining organizations. The situation is very much the same with the microprobe. The geology departments of several major Canadian universities have easy access to this instrument. Fifteen of them, to the author's knowledge, own one and a few have already acquired or are planning on acquiring a second and later model. The mining branches of the Canadian Government have similar easy access to microprobes, as at least four of these instruments are available to them in Ottawa alone. The mining companies, on the other hand, except for the few larger ones which have their own research laboratories, have not been able to take advantage of electron microprobes in the past.This failure to exploit good ore microscopes and electron microprobes has been mainly due to a lack of expertise in the use of the two instruments for the study of metallurgical problems related to ore mineralogy. Government institutions providing research and test work to the industry are few in number, and are not always equipped with these instruments or are not geologically-oriented. Information provided on a consulting basis by universities and by government mining branches is normally limited, and frequently is not oriented to the needs of the mining company."

Jan 1, 1980

By Ma Yuxin, Niu Fusheng, Yuan Zhitao, Bai Limei, Han Yuexin

"Using batch flotation experiment, contact angle measurement, particle size analysis, and scanning electron microscope (SEM), the influence and difference of pH value on the flotation rate of talc and chalcopyrite were investigate without collector at the pH range of 3~11. The results showed that, the flotation rate of talc decrease with the increasing of flotation time, while that of chalcopyrite hardly affect by flotation time, besides, the flotation rate of chalcopyrite is much less than that of talc, so the laws of flotation rate of the two minerals are independent of pH value. The flotation test data of two minerals are simulated with first order and multi-rate flotation kinetic model respectively. The simulation results showed that flotation of talc only meet the first order kinetic model, while chalcopyrite’s meet the both. In addition, According to test results of talc and chalcopyrite by the particle size distribution, SEM photographs and the contact angle measurement, the reason why talc did not conform to the first order kinetic model is not because of particle size distribution, but of particle shape. That is to say, because of sheet structure of talc, the contact angle of layers and sections are 74°and 52°respectively. At the same time, the contact angle of layers and sections are different between the particles. So flotation rates between talc particles are difference.INTRODUCTIONPossessing superior self-induced, collector-induced and sulfur-induced floatability, chalcopyrite exhibits good floatability at a wide range of pH values and potentials. Serpentine are regarded as the most difficult selected type in various chalcopyrite ore, and the predominant reason is that it contains talc. Talc, as a nonpolar layered silicate mineral, is one kind of common associated mineral in sulfide ores (Lu, 2010). Concentrate quality and flotation process of chalcopyrite are influenced as a result from the presence of talc. It is because that talc has inherent floatability which makes it readily mixed with the floated mineral and talc is easy to slime causing the slime coating of the valuable mineral (Beattie et al., 2006). Thus in order to improve the flotation effect of chalcopyrite, methods can be introduced from two respects. One method is that fast-floating talc mineral is floated preferentially, and the other is that sulfide mineral is floated prior to talc by depressing the flotation of talc mineral (Beattie et al., 2006), nevertheless, no matter with which the flotation effect of fine-sized chalcopyrite is not positive. Therefore, in order to realize the flotation separation of talc and chalcopyrite, the difference between the inherent floatability of fine-sized chalcopyrite and talc is researched and analyzed in terms of flotation dynamics in the absence of collector and frother."

Jan 1, 2016

By D. Seo, P. Au, X. Husang, D. Nagy

The production of single crystal (SX) turbine blades represents the current stateof- the-art in Ni-based superalloy design. With complex casting processes and alloy composition modifications, SX superalloys exhibit superior high temperature mechanical properties to their polycrystalline counterparts. Stresses and plastic deformation can occur in SX nickel-base superalloy engine components at various stages during their manufacture and use. For examples, stresses are created during initial solidification and also during solid state processing such as shot peening, grit blasting, blending, electrodischarge machining and welding. Stresses may also be created during service due to random events such as foreign object impacts. Subsequent exposure of SX to high temperatures during solution heat treatment and brazing repair can result in recrystallization which has been shown to be detrimental to both creep rupture strength and fatigue performance of the components. It is therefore the objective of this paper to understand the recrystallization behavior of two SX superalloys, PWA 1484 and 1483, subjected to pre-stressing and subsequent heat treatments.

Jan 1, 2006