Search Documents

By H. R. Manouchehri, A. Weh

"High voltage electric pulse comminution (SELFRAG) relies on inducing electrical breakdown that occurs when the resistivity of a dielectric is insufficient to completely block all transfer of electricity while the conductivity is not high enough to fully accommodate the flow of electricity without considerable changes to the crystal lattice. The technology is based on introducing the electrical discharges into solids immersed in water and placed between two electrodes. The technology has received significant attention since investigations have revealed the potential for fully fragmenting particles or pre-weakening rocks in order to reduce the energy consumption in comminution practices, improve liberation and potentially increase the recovery in mineral processing. Mineralogical analysis of samples showed possible liberation at coarser sizes by high voltage breakage in comparison with conventional mechanical comminution.This study explored the potential of implementing SELFRAG to treat the Sandvik’s Mittersill mine tungsten ore (scheelite) for recovery improvement. Accordingly, standard SELFRAG tests were conducted on four samples from the tungsten process plant to evaluate the energy-breakage relation and potential to liberate the value minerals at coarser size fraction for recovery improvement. The size reduction of the ore after processing with SELFRAG revealed that size deportment occurs at 0.4, 0.2, and 0.1 mm, which indicated potential liberation of gangue and target minerals at respective sizes. In comparison with conventional milling, the difference is the deportment of values into 0.4 mm sizes, which was, to some extent, confirmed by SEM liberation analysis. However, more tests are needed to proof the concept. The study has indicated that, despite consuming more energy in comparison with conventional mechanical comminution, there are promising prospects in liberating the values at coarser fraction and improve recovery by making use of SELFRAG. The energy consumption can be reduced through customized generator and equipment setup, which must be further investigated."

Jan 1, 2016

By A. Noël, R. Lapierre, M. Provencher

"Modem aluminum smelters are facing significant operating cost pressure. Key methods used by smelters to manage this pressure are automation and production-information systems to optimize processes, manage quality, anticipate problems and reduce operating costs. In 2002, Aluminerie Alouette Inc. began its Phase II Expansion project, and retained the joint venture of SNC-Lavalin and Hatch (SLH) as its engineering, procurement and construction management (EPCM) team. Alouette had the distinction of being one of the most efficient aluminum smelters in the world. Alouette already understood the importance of systems integration in project delivery. For Phase II, key objectives were identified to ensure ""a state of the art"" integrated architecture that would support Alouette's production goals to integrate the existing facilities with the expansion, to form a single efficient facility and meet project schedule and budget targets. Achieving those objectives within the context of a large project often creates major challenges due to the nature of the traditional EPCM delivery model, which relies on several vendors and third-party-systems integrators. In this case, an integrated Alouette-SLH team was made responsible for all aspects of the systems integration, taking over the task from most suppliers. The integrated team was responsible for delivering an automation system and plant-wide-production IT system for the new facilities while accommodating migration for the existing systems. Through the use of rigorous methodology and advanced state of the art technology, the IT and automation strategy led to significant value creation and is recognized today as one of the key factors of the project's success. The primary results were: fast and efficient start-up of facilities, due to quality programming and implementation; a plant able to operate as a single entity; automation and IT systems delivered before time and under budget; standard programming methods implemented throughout the plant; and reduced and simplified maintenance."

Jan 1, 2006

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

By G. W. H. Norman

"During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in mapping major faults by using aeroplane photographs with a scale of about 1,000 feet to 1 inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately.Geology of the Abitibi RegionGeneral GeologyFaults of more than one age and type occur in the Abitibi region. In order to appreciate some of the age relationships of the faults, a brief summary of the historical aspects and major structural features of the geology (fig. 1) is necessary. These historical aspects may be briefly summarized in chronological order as follows:(1) Accumulation of Archæan lavas and associated pyroclastic rocks, either alternating with, or essentially followed by, deposition of sedimentary rocks, and interrupted at least once by local and perhaps regional folding and erosion."

Jan 1, 1954

By J. M. Belland

This paper deals with the geology of the Smallwood mine in relation to its influence on mining and milling operations. Structure within the orebody, and variations in ore grade and material types, will be described and associated with the various drilling, blasting and milling operations. The orientation of planes of weakness, either bedding or jointing planes, and contacts between extremes in material types influence the size of the broken material. Generally speaking, variations in grinding rates and recovery can be associated with stratigraphic sequence and metamorphism.

Jan 1, 1966

By L. B. Smith

Introduction The property of Wright-Hargreaves Mines, Limited is situated at the northeastern end of Kirkland lake, Ontario. It lies immediately east of the Lake Shore mine, and about in the centre of the Kirkland Lake camp. The district is served by the Swastika-Rouyn branch of the Temiskaming & Northern Ontario railway, the town of Kirkland Lake being four miles northeast of Swastika, which is 63 miles north of Cobalt and 392 miles north of Toronto. The mine is developed by three shafts and has more than twenty-eight miles of underground workings. There are two main producing veins, which lie in a porphyry boss 1,350 feet wide. Milling started in May, 1921, and to-date (January, 1933) the mine has produced gold to the value of $21,770,183. Present production is at the rate of 800 tons of ore per day. For a description of the geology, reference may be made to the report by E. W. Todd on the Kirkland Lake Gold Area (1). Structure and Ore Deposits The two major productive veins on the Wright-Hargreaves property are known as the North vein and the South vein. In the vicinity of the shafts these veins are approximately 550 feet apart. A third vein, known as the Inclined vein, has been worked from its junction with the South vein at the 2,000-foot level to its intersection with the North vein at the 800-foot level. This inclined vein has to date been found only in the area east of the eastern major north-south fault. The main North vein and South vein have a general vertical dip, although local rolls and post-ore faults throw certain sections out of line. From the surface to 3,900 feet, the North vein is displaced south less than 200 feet, and the South vein at the same horizon is almost perpendicularly beneath the surface showings.

Jan 1, 1934

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By D. Milne, P. Germain, G. Sauriol

"The practical determination of optimum stope geometry has, until recently, been an art relying primarily on experience at a given operation. Due to the complex and variable nature of rock masses in situ, stopes are often designed either very conservatively, resulting in excess development, or non-conservative resulting in excessive dilution and, in some cases, in loss of ore reserves.The Geomechanics group of the Mining Technology Division, Centre de Recherche Noranda, uses a combination numerical modelling and empirical design techniques to optimize allowable stope geometries. The above methodology allows the optim ization of stope geometry for varying rockmass classifications within an operation or between different operations. Such techniques require the development of a thorough geotechnical database at each operation and are best used when calibrated to the specific operation through back analysis.This paper discusses the above optimization techniques in light of specific examples from the Noranda Group. The design methods, limitations and results are discussed.INTRODUCTIONMine design has traditionally referred to production planning, general facility layout, (i.e. ore passes, crusher stations, main haulage drifts, etc.) and ventilation design. The dimensioning and sequencing of the stopes and pillars, however, has been almost solely based on trial and error and precedent practice.More recently, numerical stress analysis has received much more attention as part of the design process. It is common now at many operations to look at the effect of proposed stope layouts and sequences on stress redistribution through the surrounding mine workings. Through calibration of actual stope and pillar behaviour in situ, one can then relate the model predictions to support requirements, safety problems, etc."

Jan 1, 1989

By M. H. ElMaghraby

This paper describes the development and validation of a strategy for vibration-based online detection of faults in a particular class of machinery commonly found in industry. This machinery is defined by two basic characteristics that preclude it from the application of standard online condition monitoring approaches. The first characteristic is that the machine is in a constant state of transient operation, thus making it difficult to differentiate between changes in transducer measurements that are due to variable duty and those that are due to machine malfunction or fault. The second characteristic is the fact that the machinery involves multiple sub systems that are subject to identical and simultaneous loading, operating environments and duty cycles. An example of such machinery is a system of multiple hydraulic pumps driving a common load. The monitoring strategy presented here employs an anomaly detection scheme together with methods of signal processing and feature extraction that exploit the parallel duty arrangements of this equipment. Preliminary data is collected from a pair or motor-gearbox assemblies used in a material haulage system in the mining industry. Testing and validation was performed on a mechatronic test bench with both healthy and faulted components. Experiments were carried out to investigate how various configurations of the system were able to detect different types of faults. The results indicate that this approach is effective and merits further investigation.

May 1, 2013

By Trygve Høy

"Important stratabound lead-zinc deposits in southeastern B. C. occur in rocks that range in age from Proterozoic Helikian to Middle Cambrian. The Sullivan deposit, and similar but smaller deposits in the Sullivan area are the only important deposits that occur in clastic rocks with little carbonate content. The highly deformed and metamorphosed Shuswap deposits, of probable Hadrynian to Helikian age, are in mixed marble, calc-silicate gneiss and pelitic schist assemblages, rocks transitional between clastics and carbonates. Deposits in younger rocks, such as the Kootenay Arc deposits in the Lower Cambrian Badshot-Reeves Formation and the Monarch -Kicking Horse deposits in Middle Cambrian dolomite, are hosted by platformal carbonate rocks.An important regional control for the distribution of deposits appears to be a northeast-trending tectonic zone that crosses the Rocky Mountains and the Purcell Mountains just south of the Sullivan area, and projects southwestward toward the Salmo camp at the southern end of the Kootenay Arc. Pronounced northeast-trending gravity and magnetic anomalies, basic volcanism of Hadrynian age (the Irene volcanics west of Creston) and a preferred alignment of Mesozoic granitic rocks indicates that the zone coincides with deep crustal structures. Within the zone are dramatic and abrupt thickness and facies changes in Hadrynian Windermere rocks and lower Paleozoic rocks, and on the east side of the Rocky Mountain Trench in Helikian Purcell Supergroup rocks, indicating that block-faulting was active intermittently within the zone from Helikian through to lower Paleozoic time. Right-lateral and reverse movements occurred on northeast-trending tear faults within the zone in Mesozoic time."

Jan 1, 1982

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961

By Alan Galley, Tom Hynes, Michel Plouffe

"Mining in Canada’s economy• Employs 320,000+ workers; Wages 30-60% above other sectors• Operates 220 producing mines, 33 smelters and refineries• Paid $8.4B in taxes and royalties to governments in 2010• Invests about $30B in capital projects annually • Largest private employer of Aboriginal Canadians 2• Core supplier to clean-technology sectors• Attracted 18% of world exploration spending in 2010• Efficient TSX processes - 1400 mining companies listed, ~50% of mineral projects are outside Canada• Estimated 1000 Canadian companies in 100 countries• Minerals account for 21% by value of Canada’s goods exports• Top 5 World Producer in uranium, potash, nickel, platinum, aluminum, diamonds, zinc, met coal"

Jan 1, 2012

By L. Long

Stirred milling of nickel laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on siliceous goethitic (SG), goethitic (G), and saprolitic (SAP) nickel laterite samples (- 2000 ?m particle size) to evaluate the effect of stirrer speed, solid content, water salinity and grinding time. A fine mineral product (-38 µm) was used to evaluate the effect of selective grinding and Ni upgrade. The optimum grinding time for the highest Ni upgrade was 0.25 min, 0.1 min and 0.1 min for the SG, G, and SAP nickel laterite, respectively. A new feed (38-2000 µm) for each nickel laterite sample was prepared for batch grinding tests under the optimum grinding conditions. Upon grinding the 38-2000 µm feed, the - 38 µm product confirmed the effect of selective grinding and nickel upgrade. Size classification followed by stirred milling is a suggested process for Ni upgrade. The best Ni upgrade result was achieved on the SG nickel laterite among the three samples. The Ni grade increased from 0.85% to 1.37%, with 27.8% Ni recovery. Bottle roll leach tests showed that for SG and SAP samples selective grinding had no dramatic effect on Ni extraction due to the slow leach rate of hard mineral particles. Stirred milling of G sample increased the surface area of goethite, resulting in higher Ni extraction. Gravity concentration through a Knelson Concentrator was not effective in the further treatment of the stirred milling products either due to the poor operating conditions or due to the mineralogy characteristics of the feed samples. The energy requirement in the stirred milling was investigated. The first pass of the signature plots study is critical for the purpose of selective grinding, because the best result on selective grinding is achieved in the early stage of the grinding process.

Aug 1, 2013

By D. Racicot, T. Hanel, E. H. Chown

Over thirty plutons in the Chibougamau-Desmaraisville belt were examined briefly in the field and sampled, in addition to the few masses that have been studied in detail. The survey indicates that the intrusions may be conveniently grouped in four main categories, based on their time of intrusion. These are; remobilized basement domes, pre-kinematic intrusions, syn-kinematic intrusions and postkinematic intrusions. Basement domes, as exemplified by the Lappa rent Massif, are composed of migmatized tonalite-diorite gneiss that has undergone at least two periods of mafic dyke intrusion and at least three major deformational periods. The rise of the basement domes was accompanied by extensive mylonitization and the intrusion of syn-tectonic plutons. Pre-kinematic plutons, such the Chibougamau pluton, are diori te-tonalite in composition, and were intruded into the supracrustal pile and partly eroded before the main deformation of the belt. Syn-kinematic plutons occur principally as marginal intrusions bordering the belt (Barlow), or as discrete intrusions along structural highs (La Dauversiere), and are either hornblende monzodiorite or tonalite in composition. Post-kinematic plutons, such as Muscocho, are principally granodiorite and often porphyritic intrusions locally deforming the enclosing rocks. The close relationship between mineralization and high-level intrusions such as the pre-kinematic and some of the post-kinematic plutons is discussed.

Jan 1, 1984

By K. Raht

LEAD poisoning is perhaps the oldest and, until recent years, the most misunderstood of all industrial diseases. Hippocrates appears to have recognized a relationship in the colic experienced by a patient who worked with metals, and the ancient literature is filled with references to the colics and 'dry bellyaches'. The colic and other sequalæ following drinking of lead-bearing waters and, particularly, wines has excited possibly more comment in the older medical literature than any other ætological factor. It was not until1656, when Stockhusen definitely connected the colic of the workmen with the fumes given off in the process, that the true danger to those working with lead was recognized. Unfortunately, something over 200 years elapsed before industry took any note of Stockhusen's discovery; it remained for Legge and Goodly and investigators of the early 1900's to forcibly educate their profession and industry to the manner in which lead gained entrance to the body. The work of Legge and Goodly was published in 1912 and the clearness with which these investigators presented the scientific data which they had accumulated will mark this volume as perhaps the first and most important contribution to our modern knowledge of the subject. It also ushered in a period when, in the short space of thirty years, lead poisoning has been reduced from one of the most baffiing and widespread o industrial diseases to one which can be anticipated and controlled. The next great contribution came in 1926 with the publication of the work of the Harvard group. Here, for the first time, was the physiological behaviour of lead laid bare, and it is to the discoveries of these authors that we owe our modern treatment of lead poisoning.

Jan 1, 1941

"Le présent article porte sur la diminution des rejets de concentrateurs produits durant l’exploitation et le traitement des minerais métalliques.Le minerai dilué envoyé au traitement a, très souvent, un certain pourcentage du stérile qui affecte directement la rentabilité des opérations souterraines et amplifie l’impact négatif sur l’environnement. Les essais de la séparation du stérile et du minerai effectués en milieu dense sur quelques types de la minéralisation d’or, ont démontré les deux possibilités qu’offre cette technique:• Dans le cas d’un minerai riche, il a été possible de séparer la part importante du toutvenant (minerai dilué contenant le minerai et le stérile) provenant de la dilution, tout en ayant un taux de récupération élevé (supérieur à 96%).• Dans le cas d’un minerai ayant une teneur sub-économique à cause d’une dilution importante, il est possible de produire un concentré ayant une teneur économique à l’entrée de l’usine de traitement, en éliminant une partie du tout-venant.En plus la séparation du stérile peut accroître, en outre, la rentabilité de l’exploitation minière, car le fait d’éliminer la partie de stérile le plus tôt possible diminue certains coûts (transport, traitement et autres). On conclue que la pré-concentration du minerai (séparation du stérile et du minerai) est probablement une seule solution actuellement étudiée qui diminue l’impact environnemental de la mine, sans avoir des conséquences négatives sur la rentabilité de l’exploitation souterraine."

Jan 1, 1997

By J. S. Redpath

Eighty feet of overburden, thirty feet consisting of fine, water-bearing sands, was encountered during the construction of a shaft collar for Chimo Gold Mines Limited at its Louvicourt, Quebec, property. This paper describes the excavation and construction methods used on the project. Open-cut methods, a sheet pile cofferdam, chemical grouting and special blasting methods were used during excavation. Concrete placement was hampered in the lower portion by a heavy water flow, and aided in the upper portion by an unusual method of form bracing. Plant and • pum11ing facilities are also described.

Jan 1, 1966

By L. Narhi, K. Haavanlammi

"Approximately two thirds of annual nickel production is used as a raw material in the making of stainless steel, and about 60% of these nickel products are in the form of metallic nickel such as nickel cathode or briquettes. In the stainless-steel production process nickel is blended with iron and chrome-based raw materials, and metallic nickel is typically only required for final steel fine-tuning. Outotec offers a new FeCrNi technology to enhance the nickel value chain for stainless steel producers. This involves the use of an HPAL-based intermediate nickel product (e.g., mixed hydroxides or NiO) as raw material in the Outotec FeCrNi process, for the production of a FeCrNi Master Alloy. The new process, designated as the FeCrNi process, offers multiple benefits compared to existing technologies such as: higher tolerance for impurities in the HPAL intermediate product, avoiding the need for further nickel refining, and the improved recovery of all metals in the FeCr process. The complete new FeCrNi value chain is based on proven technologies such as HPAL and the Outotec FeCr-process. This new innovative and promising value chain offers improved efficiencies for the HPAL based nickel production process combined with excellent sustainability aspects.INTRODUCTION In today’s global economy there is a constant need to improve the efficiency and sustainability of the metals production. The requirements for modern metal refining are tightening and cost efficient, safe and sustainable operation is the precondition for all investment. Outotec is offering now a novel way to combine FeCr and Nickel production to create a completely new value chain to source nickel to stainless steel. BACKGROUND Nickel The current nickel mine production is in the level of 2,000 tons annually and it is split 44% from sulphide based deposits and 56% from laterite deposits (Figure 1). Most (40%) of the nickel is refined to pure nickel metal whereas other products are FeNi (19%) and Nickel Pig Iron NPI (20%) (Roskill). The remaining part, roughly 21%, is nickel chemicals and intermediates. Most of the new investments in nickel are in the direct shipping of laterite to produce nickel pig iron. HPAL process is considered in few projects but no major HPAL projects have been started since the Ambatovy plant in Madagascar. Ambatovy reached the commercial production in 2014. The main primary nickel used is stainless steel manufacturing. In the year 2016 about 68% (~1,360 kt) of primary nickel production was used in stainless steel."

Jan 1, 2017

By G. Bonin, A. Jamal, G. Preciado, S. Gillis

"Accurate, easy to obtain, and reliable methods of measurement are the cornerstone of shaft and tunnel developments - during their sinking, operation and maintenance, or in some cases, remediation. This paper presents a new methodology to capture existing shaft conditions in such a manner that they can be transferred from the field to a digital copy, where they can be stored and used for engineering design purposes in a space not directly affected by the costs associated with schedule and equipment performance. The methodology utilizes basic principles of excavation alignment (plumb lines and survey instruments) while adding modern LiDAR, geolocation and survey control tools that can more completely capture the surrounding environment. The complete cycle of collection, processing, and delivery of pertinent information underground can take under an hour. During sinking, capturing data as a live stream measurement and being able to assess the alignment of the shaft liner can be critical to meeting rigid design tolerances. As sinking progresses, small changes in alignment or liner deviations can be captured and immediately corrected. Likewise, post-construction as-built conditions can be recorded and digitized, which will allow the mine personnel to compare the proper working condition to the actual condition years later. Observed changes can be identified and planned as future shaft repair works. This methodology has been developed and successfully deployed during the on-going sinking works of the two shafts at the Jansen Potash Project in south-central Saskatchewan and is described in greater detail in this paper.INTRODUCTION Light Detection and Ranging (or LiDAR) scans of the BHP Jansen Production and Service shafts during construction identified sections of both shafts where the internal radius of the temporary primary liner was insufficient to accommodate the tolerances of the permanent liner that was to be installed inside the temporary liner. These locations are referred to as “tights”. The “Tights Removal Program” was designed to collect high resolution point clouds of the shaft, using stringent survey control, that could be compared to the design profile to generate a heat map of locations for removal of up to 75 mm of steel-fiber-reinforced, 70 MPa concrete liner. This work was all on critical path, which made it valuable to save time on the schedule. Because concrete removal was a time-intensive task, it was essential to locate and remove only the concrete that would encroach on the planned permanent liner, while attempting to maximize the amount of cutting time. Removal was carried by a road header attached to a Brokk(R) 160, a small multi-attachment demolition machine."

Jan 1, 2019

By Y. Zedan

In this study, the statistical design of experiments (DOE) was applied to study and regulate the properties of near-eutectic Al-11%Si alloys. Develop regression equations for such response variables as hardness, yield stress, ultimate tensile stress, percent elongation, total cutting force, cutting power, and tool life together with other factors which, include the percentage composition of the alloying elements, and the requisite modification (Sr) level. These equations may be analyzed quantitatively to acquire an understating of the effects which the main variables and their interactions may have on the mechanical behaviour and the machinability of the alloy under investigation. The results reveal that increasing the levels of Cu and Fe content results in an increase in hardness, yield stress, and ultimate tensile strength in both modified and non-modified alloys. On the other hand, both Cu and Fe appear to affect the percentage elongation adversely, whereas the Sr-level has a positive effect on this parameter. It was found that Sr-levels have the most significant effect on the cutting forces and cutting power followed by the content in Fe and Cu. The results also reveal that the interaction coefficients of these variables have a significant effect on tool life compared to the main independent variables. This fact may be attributed to the formation of complex insoluble phases between Cu, Fe, Si, and Al as investigated using Scanning Electron Microscopy (SEM) attached to an EDX analysis system. The accuracy of the regression equations in predicting the expected properties has been verified by carrying out random experiments in the range of variation of these variables.

Jan 1, 2011