Search Documents

By F. Kapeller, G. Herget

"The need for monitoring the effect of changes in ground stresses due to mining in hard rock has existed for many years. The Mining Research Laboratories of CANMET, EMR have developed a new tool which monitors with high precision the radial deformation in boreholes. The result is the Mining Research Laboratories strain monitoring system (MSMS) which uses the highly stable and very sensitive vibrating wire principle to monitor deformations in relatively large boreholes, e.g. 76 mm to 153 mm diameter.The vibrating wire is strung across a relatively large proving ring and operates at a frequency between 600 to 1800 Hz. The read-out system is based on continuous vibration.The ring is installed with a hydraulic tool and brought into contact with the surrounding rock through precisely machined and guided wedges. The resolution of the system is in the neighbourhood of 4 x 10-4 min/ Hz. The data collection can be carried out with a portable read-out unit and provisions are available for automatic data collection. Stresses may be calculated from strain readings.The system was tested in cooperation with the Centre de recherches minérales at the Niobec Mine in Quebec for the purpose of monitoring the effects of drill drift development and slope mining on surrounding ground stresses.After access was available to the site, 153 mm diameter holes were drilled for the determination of in situ ground stresses. These holes were then used to install the strain monitoring system. The effect of drill drift development and production blasting in stopes C-203-13 and C-203-15 on ground stress distribution could be observed clearly.The horizontal relaxation in the core of a pillar which occurred during mining of adjacent rooms was between 0.082 mm to 0.111 mm. Calculations of stresses from these deformations indicate that the rock material is still in an elastic condition.Roctest of Montreal has obtained a license on the manufacturing and distribution rights. A patent has been registered and CANMET will assist in installation of the MRL strain monitoring system and the interpretation of records."

Jan 1, 1989

By D. Kovachevich, M. A. Pfeifer

"A t remote locations typical of mines and associated ore processing plants, diesel electric generators are ideally suited for power plants due to their inherent operating flexibility, efficiency and reliability. In recent years rapid escalation in fuel and related transportation costs has made extensive waste heat recovery from generating sets financially attractive to a much greater extent than previously.The paper outlines key considerations during planning and design stages for utilizing the various waste heat sources available to best advantage. Based on two /980 mining projects built in the Canadian Arctic, data is presented on potential operating and capital costs savings. A review of heat balances, engineering flow diagrams and major equipment selections for process and building heating systems utilizing waste heat is included.IntroductionResource projects increasingly occur in remote areas requiring on-site self sufficiency in electrical power generation. For such projects, the low- or medium-speed turbo-charged diesel engine is very often the preferred choice as a prime mover for the generating sets . It is inherently reliable, has good response to load changes and has comparatively high fuel efficiency over a wide load range . From a project execution standpoint, It is capital cost- competitive and procurement lead-time normally ' fits ' within tight schedule constraints. In addition, its potential for waste heat recovery is excellent , particularly in northern climates where space heating requirements are usually substantial, and also where there a re requirements for heat for process and plant services.The high cost of fuel , with add-on transportation costs , provides a major incentive to fully exploit the available waste heat recovery potential o f such installations.As a result of the rapid escalation in the price of petroleum products following major crude oil price increases in 1973 and again in 1978-79, liquid petroleum fuels, having the desirable properties of comparatively high heat content and transportability, are no longer 'cheap' commodities and have become so valuable that industry has widely undertaken serious conservation efforts.Currently, it appears that petroleum cost trends of the 1970s may not continue, at least in the near term, and that we may see somewhat reduced energy costs for a time. In the longer term , and certainly within the life spa n of major projects, however, it is generally believed to be inevitable that these fuels will be increasingly expensive . Energy costs are today a major operating cost for remote minerals processing plants and will remain so for the foreseeable future.In order to meet the economic challenge posed by high energy costs, future projects should be thoughtfully planned from the outset with the goal of minimizing energy requirements and maximizing the use of waste heat recovery to meet such requirements. There is also considerable potential for significant energy savings by retrofitting of existing installations."

Jan 1, 1984

By J. E. Nelson

This paper will examine the problems inherent in matching grinding mills with electric motors through connecting elements such as clutches. Emphasis will be on the uncertainties of mill torque and power demands and the need to recognize these if dependable, safe designs are to be obtained.

Jan 1, 1972

By J. Olsson

The paper describes and discusses the use of stainless steels for leaching plants emphasising the duplex family, i.e., austenitic-ferritic stainless steels. This group has generally twice the proof strength of the more common 300-series austenitic grades, which implies possibilities to reduce the gauge at construction of pressure vessels and atmospheric tanks and vessels and thereby possibilities to reduce the weight. The duplex grades have also higher surface hardness resulting in better resistance to mechanical wear, i.e., abrasion and erosion corrosion. The lower contents of nickel and molybdenum imply lower cost and a more stable price considering the present market situation for these alloying elements. Corrosion data from laboratory and pilot plant tests, as well as examples of applications of duplex and highly alloyed austenitic grades, are presented. Cu2007 - Volume IV (Book 1) The John E. Dutrizac International Symposium on Copper Hydrometallurgy Edited by P.A. Riveros, D.G. Dixon, D.B. Dreisinger, M.J. Collins Toronto, Canada,

Jan 1, 2007

By R. Flood

"Oil has been discovered off Newfoundland in a number of locations on the Grand Banks, the most notable and exciting being in 1979 when Hibernia was discovered. This discovery has brought new challenges to the province as well as to all of Canada. During the seven years"" since its discovery, both industry and governments have attempted to define its parameters and to find the most efficient and economical way to develop the field.A number of studies have been completed during the interval and in 1985, Mobil Canada Ltd. and partners stated that they would prefer to develop the field by using a concrete Gravity-Based Structure (GBS). IntroductionHibernia is located in an environmental climate much more severe than that of any previously developed oil field. The wind and wave conditions are similar to those of the North Sea, but unlike the North Sea, any structure on the Grand Banks would have to contend with ice floes and icebergs. Decisions had to be made on whether fixed structures could be put in place that would withstand the pressures of the ice and the impact of an iceberg, or whether structures that could be removed when such impacts were imminent would be used.Early studies in 1981, determined that it was possible to build a concrete Gravity-Based Structure which could withstand the impact of the largest icebergs that are anticipated to float in that area of the banks.Additional studies increased the knowledge of icebergs: their patterns and size, and verified the original conclusions that Concrete Gravity-Based platforms would provide a practical solution."

Jan 1, 1988

By Eric Best

"In the past two to three years, all continuous mining machines at the Potash Corporation of Saskatchewan Mining Limited, Lanigan Division, have been changed over to a new cutting pattern using 1 -inch- and 1-3/l6-inch-diameter self-sharpening pencil bits. The bits are arranged in a cone-type pattern across the face on 2 1/2 -inch and 3-inch spacing. The result is that the ore is removed by chipping and flaking. Previously, rap-lock bits were used, with the pattern being several bits in single rows at wide spacings. The cutting action was grinding and breaking.Besides improved penetration rates and lower bit costs, there are many other advantages. The ore size is much smaller, resulting in less wear and tear on conveyors and other associated equipment. Feeder-breakers are no longer routinely set up at the head end of every extensible belt, as the banana-shaped chunks of ore that used to require breaking are no longer produced. Also, less dust is generated by the cutting heads and fewer stops are required for bit changes. Even the mill operation has been improved, as fewer fines are produced.Further improvements are still sought after, but, all in all, the new cutting pattern is considered to be a giant step forward from the old method."

Jan 1, 1981

By I. Filzwieser, S. Konetschnik, A. Filzwieser, A. Anzinger

Production in copper electrorefining tankhouses mainly depend on two factors: The deposition area, which is a result of the amount of installed cells and cathodes, as well as the current density - the amperage per square meter of deposition area. The present paper shows, that the most economical way of achieving a certain production is to maximize current density by using the METTOP-BRX-Technology - as building and infrastructure can be kept more compact. This industrial proven technology applies a parallel electrolyte flow in each electrolysis cell. In 2011, the first fully industrial applications started up: At the secondary smelter Montanwerke Brixlegg AG, 156 cells are equipped with the METTOP-BRX-Technology; this allows a current density of 390 A/m². Xiangguang Copper Co., Ltd. - a primary smelter and refinery - operates its new tankhouse (720 cells) at 420 A/m²; this stands for an production increase of 50% compared to the same sized ISA tankhouse which is limited to 280 A/m². The first part of the present paper gives a cost comparison between a conventional copper electrorefining tankhouse and a high current density tankhouse when assuming a Greenfield project. The second part describes the cost savings when installing the METTOP-BRXTechnology in an already operating tankhouse.

Jan 1, 2014

By M. Silva, G. Olivares

In a leach pile, the drainage layer or commonly known as the cover layer has been a matter of discussion due to the multiple phenomena or events that occur within it which impacts negatively the leaching process. All these events are directly related to the loss of draining capacity and irregular flow net due to an excessive compaction and entrapment of fines reducing the flow velocity which in turn cause more fines to get trapped. Over time the problem will continue to worsen rapidly and accelerating continuously like a geometric progression. When the cover layer gets to a certain level of deterioration, the only alternative to continue operating safely is to replace the entire cover material, a huge cost for any mining operation. TESRA has developed a solution to counteract the accelerated advance of the deterioration of the drainage layer. The solution consists of using large agricultural tractors coupled to a proprietary design of a heavy- duty subsoiler-ripper for deep tillage for loosening and breaking up the ground at various depth and with different legs spacing from 0.4 m or above. Also, if the ground still requires additional breaking, TESRA proposes the use of a rototiller that breaks any lumps to homogenize the ground to a certain particle size. With the subsoiler-ripper/rototiller combination equipment a layer of 0.5 m deep is properly treated to match closely the original conditions of the ground thus regaining the flow net as close as to the original seepage condition. Once the ripping is completed the subsoiler-ripper tool is replaced with another that is similar to a plow and thus continue with the installation of drainage pipes. The tool digs a Y-type profile trench allowing the pipe to sit precisely at the bottom of the trench, contributing additional lateral and lower support. This tool controls the installation depth of the drainage pipe at different inclination grades and also eliminating any irregularities that may block the flow of the leaching solution. Sometimes the obstructions block completely the flow of the solution. The main result of this methodology is the reduction of groundwater levels and at least 2% less humidity in the leaching gravel due to an increase in the draining capacity of cover. The methodology developed by TESRA applied during a couple of cycles of a dynamic leach pile has proven to be a real alternative to remedy and recuperate the cover close to its original conditions. The methodology requires only one large tractor and two accessories operated in different stages while replacing the more traditional and less efficient machinery such as the Bulldozer, Motor-grader, and backhoes.

Jan 1, 2019

By J. Stumper

The control of the distribution and movement of liquid water is crucial for increased reliability and durability of PEM fuel cells: whereas the proton exchange membrane requires a minimum amount of liquid water for optimum operation, water excess in the GDL will impede reactant gas access to the catalyst layer thereby reducing performance. In order to understand the relationships between water management on one hand and fuel cell performance and durability on the other, Ballard has been developing a number of minimally invasive techniques that can throw light on the role of liquid water for both cell performance and durability. This paper introduces a novel measurement method that can provide information about the amount and distribution of liquid water under operation. It is shown how the MEA Resistance and Electrode Diffusivity (MRED) method can be used to determine i) the amount of liquid water in the fuel cell, ii) the pure ohmic cell resistance and iii) the O2 -diffusivity of the cathode. Furthermore, through a combination of the MRED method with current mapping it is possible to determine spatially resolved MEA resistance profiles.

Jan 1, 2005

By D. C. McKechnie

To the examining engineer, the ever-recurring problem involving the valuation of ore in a prospect presents at different times highly divergent aspects- some entirely physical or mathematical, others essentially personal. The majority of the problems discussed in this paper are obvious to the engineer, and need little elaboration. By the prospector and the general public, however, a number of these questions are often and completely over-looked, or else approached in such a way as to produce final results which are, to say the least, misleading and at times decidedly erroneous. While the purpose of this paper is to deal with prospects or potential mines, many of the problems considered apply equally well to mines with developed ore reserves. As the usual showings on a prospect consist chiefly of a few open-cuts and a limited amount of underground development work, an estimation of the actual ore reserves is a question of minor import, and seldom enters appreciably into an estimation of the probable value of the particular property. The physical valuation of a prospect mainly involves the consideration of such subjects as the general geological features exposed, the strength and type of mineralization, the width and persistence of any associated veins, shear zones, fractures or contact zones, together with the possible grade, size, and continuity of any ore-bodies that may there occur.

Jan 1, 1930

By S. Hobo, M. Yagisawa, T. Uchida, C. Tokoro, T. Kato

In this study, quantitative modeling was carried out for the treatment of simulated waste water containing As(V), Zn(II) and Hg(II) as toxic elements, and Fe(III), Na(I) and sulfate as coaxing ions. The objective was to predict the pH and residual concentrations of all the elements in solution after the neutralization/co-precipitation treatment. To accomplish this, the removal mechanism for As(V) and Hg(II) by ferrihydrite precipitation was first investigated for simulated waste water containing only As(V) or Hg(II). From the experimental results, it was confirmed that the removal mechanism involves not only surface complexation but also surface precipitation. However, surface complexation is the main mechanism for As(V) and Hg(II) removal to meet the target levels regulated in Japan. Next, the surface complexation model was constructed for the removal of As(V) and Hg(II) by ferrihydrite. The specific surface area and site density were determined from reference values proposed by Dzombak and Morel (1990). By comparing the experimental and calculated results, it was confirmed that our constructed model could successfully represent the experimental results. Furthermore, the surface complexation model was coupled with chemical equilibrium calculations and applied to the neutralization of simulated waste water containing As(V), Hg(II), Zn(II), Na(I), Fe(III) and sulfate. The constructed model could successfully represent the pH edge for As(V), Hg(II), Zn(II), Fe(III) and SO42- removal. In addition, the constructed model could represent the ion balance. Thus, our constructed model is useful to estimate the amount of neutralizer that is needed to achieve a target pH.

Jan 1, 2016

By Mory Ghomshei

As fossil fuels become depleted over the next century, it is imperative that Canada and other countries examine ways to transition to other sources of energy, particularly renewable resources. A critical obstacle to developing Canada?s renewable energy resources is the scarcity of infrastructure to wheel the generated electricity to a viable market. For each megawatt of renewable electrical power, a maximum of 1 km of connecting power line is typically feasible. This means that hydropower, geothermal, and wind power projects with capacities up to 100 MW must be located within a maximum of 100 km of a main power line in order to be economically viable. With a total length of about 1200 km, the proposed Northern Gateway oil pipeline project creates an excellent opportunity to become a corridor that can seed renewable energy projects in Northern British Columbia and Alberta. Utility companies must build new infrastructure to provide the electricity for constructing and operating the proposed pipeline. The pipeline and linked power line infrastructure therefore, should be designed and built with consideration to create an energy highway to the significant renewable energy resources, such as hydro, wind, and geothermal, in the vicinity of the proposed pipeline. Some of the important renewable energy resources in northern British Columbia can be developed in connection with the proposed pipeline. It is estimated that close to 2,500 MW of commercially viable wind, geothermal and run-of-river power resources are present in the proximity of the proposed pipeline corridor. While oil flows westward from the Alberta bitumen fields, the generated green power can flow eastward to help the Canadian oil sand industry to offset as much as 10 Megatons of carbon emissions per year. The generated carbon credits are equivalent to 75% of the emissions associated with extraction of the 525,000 barrels per day of oil from oil sands, intended to be carried by the pipeline.

Aug 1, 2013

By J. E. Tupper

"This paper will discuss strategies for the introduction of computer technology in the mine environment. More specifically, it will focus on issues such as: (a) make or buy; (b) programmer less mines; and (c) support from corporate groups.The paper relates these strategies to systems for mine operations. These will be illustrated by considering the implementation of some phases of these systems at Teck Corporation.IntroductionThis presentation addresses some of the major considerations in a strategy for mine computerization and then relates these considerations to the computerization cycle and Teck Corporation.Strategy is defined as a conceptual framework or plan to accomplish a goal. For purposes of this paper, the goals can be more simply defined for operational purposes as either increasing revenue or decreasing costs.The strategy will allow us the framework for measuring tactical decisions such as computer and software acquisitions.The Mine Life CycleTo start with, let us look at the mine life cycle from a computer systems point of view:-Exploration-Property Development-Feasibility-Construction-OperationFrom a systems point of view, the exploration cycle is oriented to geophysical and geochemical computing. Property development starts with drilling and building the geological data base. The feasibility cycle includes all stages of evaluating the decision to proceed with mine development: ore reserve calculations; mine planning; and financial projections. Construction includes project management and project accounting systems. Systems required for operation are those needed by personnel at the mine site."

Jan 1, 1982

By John Stubbs

Sub-Surface Shaft excavation Mine development Headframes Surface Production facilities Product storage and loading Tailings area Infrastructure Discovery Lodge Utilities Operations complex Port Marine loading Rail unloading and storage

May 1, 2013

By Julian V. Simela

Conventional methods of underground surveying use theodolites/total stations and 3D laser scanners to obtain information about the underground environment. Current methods of geo-referencing these instruments to a mine reference system include triangulation, trilateration and resection. However, despite technological advancements, surveying procedures have remained slow, laborious and relatively unchanged during the last half-century. Recent innovations in the robotics community have shown that automated mapping of underground mining tunnels can be undertaken using 2D/3D laser scanners. These techniques have the potential to, in turn, improve upon current underground surveying and mapping methods. Automating surveying and mapping using current surveying tools without changing the setting up procedures or removing current constraints, or even changing the type of equipment used, does not change the status quo. The problem of moving from a static, tripod based surveying and mapping system to an unconstrained mobile surveying and mapping system is the subject of this paper. A current challenge for automated mapping is the ability to automatically geo-reference a mobile mapping system to a mine reference system. For a mobile mapping system that uses a horizontally mounted 2D laser scanner to gather data of the underground environment, the challenge of determining its position and orientation within the mine environment is magnified even more. This paper introduces Mobile Automated Scanner Triangulateration (MAST), a technique under development at Queen?s that is designed to geo-reference a mobile mapping system to a mine reference system for the purposes of underground mine surveying. MAST quickly and automatically determines scanner 2D position and orientation (azimuth) in a mine reference frame by using minimal human input.

Aug 1, 2013

By Edward Rybinski, Serkan Dikmen, Walter Valery, Jorge Ghersi, Roberto Valle, Alex Jankovic, Javier Linares, Frank Davila

Compañía Minera Antamina is a polymetallic mining complex that produces copper and zinc concentrates as primary products and molybdenum and lead/bismuth/silver concentrates as by-products. In 2007, Metso Process Technology and Innovation (PTI) was contracted to increase SAG mill throughput by integrating and optimising blast fragmentation, crushing and grinding for the harder M4/M4A (CuZn) ores. Following the implementation of recommendations provided by Metso PTI, the SAG mill throughput increased from 2750tph to reach an average of 3600tph for the remainder of 2007. Due to continued application of mine to mill integration and optimisation philosophy, by 2010, the concentrator consistently exceeded the target of 4400tph while processing harder CuZn ores.

Jan 1, 2012

By A. Fortin, C. Fréchette, M. Kreuh

Éléonore project is a gold ore processing plant at a mine site located near James Bay, Quebec, Canada. SNC-Lavalin was mandated by Goldcorp to perform EPCM services on the ore processing plant and permanent infrastructures of the project following an internal pre-feasibility study. The project incurred considerable challenges due to fast-tracking from a pre-feasibility to detailed engineering and construction. The paper reviews how the EPCM was carried out. Some of the challenges resulting from skipping the feasibility study stage are discussed. The paper also presents how multiple offices across Canada were used for the engineering design.

Jan 1, 2015

By Michael Li

Paste backfill as a means of supporting underground mining is gaining popularity. Despite this trend, engineering and design of mine paste backfill systems are still largely based on empirical methods rather than established scientific principles. Because of a lack of sound understanding of mineral paste flow, some degree of trial and error is often involved during commissioning and operating of new paste fill systems. New operations often have to be built with flexibilities and contingencies, escalating the overall project costs. This paper reviews the applicability of some scientific and engineering principles to mineral paste flows. Recent experimental data are used to illustrate important points. The phenomenon of mineral paste flow is examined under the context of improving the efficiency and reliability of underground delivery. Gaps in our understanding of mineral paste rheology are pointed out and from those some future research directions naturally emerge. Status and problems of the current engineering and design practice are also briefly discussed.

Nov 1, 2002

By Karol Kostúr

This paper briefly describes the current state of underground coal gasification (UCG) processes globally and in the Slovak Republic. Recent results of laboratory and technical tests are presented. In addition, on site measurements have added new knowledge of UCG technology. A series of laboratory tests based on physical models shows promise for managed UCG process control.

Aug 1, 2013

By Norma G. González

La littérature et notre expérience en Bolivie dans une communauté minière très divisée comme celle de Huanuni nous montrent le besoin d?envisager des négociations gagnant-gagnant entre communauté et entreprise minière, non pas comme un point de départ, mais comme un résultat à atteindre, qui nécessite la préparation de conditions préalables. Cela implique fondamentalement de mettre l?accent sur le processus qui permettrait par la suite aux parties de mieux traiter les questions de contenu. Suivant cette hypothèse générale, l?initiative conjointe entre le Ministère des ressources naturelles du Québec et le CECI ?Développement des mécanismes de négociation entre communauté et entreprise minière? peut dégager, après un an et demi d?expérience pilote dans le site minier de Huanuni, département d?Oruro, Bolivie, les leçons préliminaires suivantes. Ce processus requiert: ??Agir, en tant qu?organisme consultant tierce partie, selon des principes et une méthodologie qui relèvent de la Communication publique et de la Médiation ; ??Comprendre et agir à partir de la ?réalité sociale? des parties en présence: l?entreprise minière, l?État et les différents groupes de la communauté; ??Intervenir sur les ?réalités sociales? des parties, par des actions d?éducation et de diffusion dans le but de préparer les personnes, les institutions et les organisations de la société civile, à des changements durables du modèle de communications existante; Approfondir la compréhension de la ?réalité sociale? du conflit (la culture du conflit, les méthodes populaires de résolution des problèmes et de gestion des conflits) afin d?offrire aux bénéficiaires les technologies appropriées pour la transformation de cette culture de confrontation violente en gestion constructive des conflits. Par ricochet, nous espérons ainsi faciliter l?attraction des investissements dans le secteur minier.

May 1, 2001