Search Documents

By C. Liu

Corrosion behavior of the stir zone in a friction stir weld of dissimilar A12024/AZ31 alloys was investigated in the immersion test in distilled water (pH=6) for different times. Microstructures and the distribution of chemical elements were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Due to the difference in the corrosion potentials between A12024 and AZ31, the AZ31 alloy constituent in the stir zone was susceptible to the corrosion attack in the distilled water. The corrosion attack was found to occur in the narrow region of the AZ31 alloy adjoining the A12024 region, where there was a low ratio of anode-to-cathode surface area. The corrosion attack became more severe in the AZ31 alloy regions with increasing immersion time. The A12024 alloy region in the stir zone of the weld was protected by cathodic reactivity due to sacrificial anode AZ31 alloy.

Jan 1, 2007

By A. J. Hyett, R. D. Reichert

"A laboratory and field research program was conducted to investigate the major factors influencing bond capacity of grouted cable bolts. The results indicate that cable bolt capacity most critically depends on the grout uniaxial compressive strength (UCS), the radial confinement, and the embedment length.In the laboratory &apos;split-pipe&apos; tests were conducted using P VC, aluminum and steel pipes to provide radial confinement, and field test sites were chosen in granite, limestone and shale rock masses. For both datasets higher capacities were obtained under conditions of higher radial confinement. A correlation between the two was obtained through a comparison of the radial wall stiffness of the laboratory pipes with that of the field boreholes as measured using a high pressure dilatometer. Cable bolt capacity was found to increase with embedment length though not in direct proportionality.The use of low water cement ratio grouts (<0.40) can increase cable bolt capacities by 50% to 75%. This effect is maximized under conditions of high radial confinement. However, the use of super thick grout paste (0.30 and less) may be both impractical and undesirable, first because of their limited pumpability and second because of their inconsistency in strength. Grouts with a water cement ratio of between 0.35 and 0.40 are recommended for practical cable bolt applications."

Jan 1, 1992

By M. N. Pons, F. Ferrari, V. Houzelot, B. Laubie, A. Bani, Université de Lorraine-CNRS LRGP

"More than 400 plants in the world are able to accumulate nickel in their aerial parts at concentrations higher than 10 g per kg of dry biomass. Then, nickel (Ni) can be recovered from the biomass of these hyperaccumulator plants. Agromining is a chain consisting in growing such plants and recovering metal and has been developed thanks to the combined know-how of agronomy and hydrometallurgy. Plants can be grown on serpentine soils, containing rather high concentrations of Ni, on sterile heaps or on contaminated soils. This crop enables us to extract Ni from secondary resources, and to improve soil quality by lowering its metal content. For example, Alyssum murale can be grown at the field scale in the Balkans, at yields corresponding to 110 kg Ni per hectare.Hydrometallurgical processes have been designed from the lab scale to the pilot scale to produce nickel salts: ANSH (ammonium and nickel sulphate hexahydrate), nickel sulphate, acetate, etc. and so on. These salts are used for surface treatment and in the paint and chemical industry. Ni salts are prepared from ashes, after plant calcination. Processes are based on the conventional methods of hydrometallurgy: acid leaching followed by different precipitation steps. These processes will be presented, as well as the pilot scale design. A life cycle assessment has been performed and clearly shows the environmental interest of this approach as a potential part of an anti-erosion strategy. An economic assessment has proved process feasibility and the final step is the launching of a start-up. At the moment, the approach is widened to other metals (cadmium, cobalt) and rare earth elements (REEs)."

Jan 1, 2016

By Z. Zhao, B. Li

"Fractures are the key channels for fluid flow and mass transport in fractured rocks of low/negligible matrix permeability. In single rock fractures, surface roughness causes fluid flow in tortuous paths, and reduces the overall fracture conductance. A number of empirical models have been proposed to relate the reduced hydraulic aperture to the mechanical aperture due to surface roughness, which were revisited and compared. Using two of those relationships between hydraulic apertures and mechanical apertures, we studied the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks. The results show that fracture roughness can affect the flow rates and residence time to varying extent, mainly depending on the empirical models between hydraulic apertures and mechanical apertures. However, fracture roughness has negligible influences on the general patterns of fluid flow (channeling) and solute migration (e.g., travel paths and shape of breakthrough curves). This is because the connectivity of a fracture network is mainly determined by other geometrical parameters (fracture positions, orientations, and lengths), rather than roughness or apertures. INTRODUCTIONIn fractured crystalline rocks of low or negligible matrix permeability, fluid flow and contaminant migration mainly occur within the connected fractures. An understanding of fluid flow and contaminant migration in fractured rocks is a crucial issue in many deep underground projects, e.g. underground repositories for radioactive waste, CO2 sequestration, enhanced geothermal systems, oil and gas production, etc. Rock fractures are typically rough-walled, and surface roughness appears to have first order control on the mechanical and hydraulic behavior of single rock fractures (Boutt et al., 2006).It is well known that the mechanical aperture of a rock fracture is usually larger than its hydraulic aperture, due to fracture surface roughness (Tsang and Witherspoon, 1983). However, for naturally fractured rocks including numerous discontinuities, the effects of this reduced hydraulic aperture in local fractures on macroscopic fluid flow and solute transport in complex fracture systems still remain unclear. Many previous studies assumed identical hydraulic and mechanical apertures in discrete fracture network models for simplicity (Min et al., 2004; Zhao et al., 2011). Therefore, the main objective of this study is to evaluate the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks, by employing the empirical models that relate the hydraulic aperture to the mechanical aperture."

Jan 1, 2015

By A. H. Winckers

"The Sullivan Mine and Concentrator are owned and operated by Cominco Ltd. and are located in the Rocky Mountain Trench, in Kimberley, British Columbia.The Sullivan Concentrator commenced operation in 1923 at approximately 2,500 tons per day. The concentrator was enlarged in several stages and by 1945 was treating 8,500 tons of ore per day. In 1949, the capacity of the concentrator was expanded to 10,000 tons per day with the completion of the sink and float plant, the installation of the rod mill, an underground crushing plant and a 4-mile underground and surface electric railway from the underground crushing plant to the concentrator. Throughput now averages 7,000 tons per operating day, or 2,400,000 tons per year.The concentrator operates 7 days per week, 24 hours per day while the underground crushing station operates 5 days per week, 24 hours per day. The ore is essentially a replacement deposit in argillaceous quartzite of Precambrian age. The ore bodies are massive deposits consisting of fine grained mixtures of sulphides, sometimes interbanded with the country rock and varying widely in their content of lead, zinc, iron and silicates. The principal economic minerals are galena and marmatite (7 ZnS:FeS). Iron is mainly present as pyrrhotite, and to a much lesser extent as pyrite. The intimate association of these sulphides necessitated the development of a successful differential flotation process before the ore could be beneficiated profitably."

Jan 1, 1981

By R. S. Adhikari

This paper presents an innovative computer vision method for condition assessments of bridges with multiple defects in bridge elements using digital images. This work utilizes 3D model of existing bridges and overlays digital images on 3D model to simulate on-site visual inspection. The analysis of element condition index (ECI) of bridges requires information about the severity and extent of defects in elements. In general, ECI is evaluated manually during routine bridge inspection considering the severity of dominant defects. The evaluation of ECI with multiple defects needs to be addressed with consideration of dominant defect as well as the interaction among defects. However, Image-based quantification techniques largely depend on geometry of objects (i.e. shapes). Shape vectors of a given object change as they are translated, rotated, and scaled with different magnitudes. This work considers shape preserving algorithms such as, affine and projective transformation for proper image alignment. Semi-automated approach for detection and quantification of concrete distress such as cracks and spalling are considered for the defects analysis. The proposed methodology ensures the consistency in reporting ECI and eliminates the shortcoming of traditional approaches.

Aug 1, 2013

By H. H. Gardner

Introduction The Greenhill mine of West Canadian Collieries, Limited, is on the Alberta side of the Crowsnest pass, twelve miles from the Alberta British Columbia boundary-line. Here, five coal seams of Lower Cretaceous age are found in the Kootenay formation. They outcrop on the north and south slopes of the valley, with strike approximately N.30°W., paralleling the main range of the Rocky mountains, and dip about 40 deg. westward. Of the five seams, only two, designated No. 1 and No. 2, have been worked to date. On the West Canadian Collieries property, No. 1 seam ranges in thickness from thirty feet to nil. Generally, it has a hard, strong conglomerate roof. No. 2 seam is separated from No. 1 by forty-five feet of shales and sandstones. It has a thickness of eight to thirty feet.

Jan 1, 1947

By A. E. M. Warner, P. J. Mackey

Copper metal is produced in large or small tonnages in almost all countries of the world—handling raw materials in the form of either as-mined or milled ores, custom concentrates, or other custom materials including scrap and recycled copper. The scale of operations and type of technologies used around the world varies widely. There is a certain concentration of both mining and smelter-refinery production as a total of ten countries produce some 80% of world mined copper, while ten countries—mostly different ones— produce about 80% of smelted and refined copper. As a result, international copper trade is significant. The present paper takes the reader on a virtual tour of the copper plants throughout the world with a focus on smelter facilities. Operations and technology employed at each plant visited are discussed including a brief historical sketch. Future trends identified during the world tour are also discussed. The present authors considered sufficient time was required for a thorough study tour and settled on eighty days—the same as that for the celebrated fictional story of world circumnavigation in the 1870s. INTRODUCTION The celebrated French writer Jules Verne published his book “Around the world in 80 days” in English in1873 and it is the story of Phileas Fogg and his French valet Passepartout circumnavigating the world in 80 days in the fall of 1872 on a £20,000 wager (equivalent to over 2 million pounds today) from the exclusive Reform club in London. This is an interesting period for copper as it started trading on the London metals Exchange in 1876 and the start of global copper production chains started to take off at this time with the rapidly increasing electrification of the world. The production chain includes mining, mineral processing, smelting, refining and fabrication. Since 1880 annual world copper production has increased by over 150 times from 154,000 tonnes in 1880 (nominally considered as smelted copper—essentially the only route at the time to marketable copper) to over 23 million tonnes today (including total refined copper of 19 million tonnes of smelted copper including scrap and 4 million tonnes by solvent extraction-electrowinning), in tandem with increased electricity usage, along with significant transportation usage and for manufactured products (Figure 1).

Jan 1, 2019

By Nicolas Gatelier, Sophie Laurent, Thierry You

Hard-rock caverns for hydrocarbon storage are a very particular type of underground facility controlled not only by local administrative and regulatory constraints that can be very specific, but also by the possible risks of geotechnical or geomechanical failure. Each such facility throughout the world is a prototype that needs to be adapted to very different site conditions. The straight forward application of design methodologies from relatively similar fields (mines, tunnels) can be very useful, but risks holding back the scientific and technical improvements needed by an engineering industry in full development. Here we look at various case histories and at problems that have been raised where recent attempts at standardization would appear to have been ill adapted, and where storage designers, through experience and judgment, may still provide innovative engineering solutions.

Jan 1, 2015

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By K. Sakaguchi, T. Yokoyama

"In-situ rock stress measurement was carried out in the Kamaishi mine of Iwate Prefecture to quantify the variation of the shallow crustal stress field associated with the 2011 Tohoku-oki earthquake. Stress measurement was conducted by the Compact Conical ended Borehole Overcoring (CCBO) technique, which is one of the stress relief method. The CCBO technique is the one of the suggested method of ISRM. Measurement period is from 1991 to 2014. Main results obtained in this study can be summarized as follows.The direction of the maximum principal stress did not change much before and after the earthquake. However, the directions of the intermediate principal stress and the minimum principal stress of one year after the earthquake changed from those of before earthquake. Namely, the direction of intermediate principal stress was East-West horizontally, and the direction of minimum principal stress was vertically. This state of stress is reverse fault type and was maintained for three years after the earthquake.The magnitudes of principal stresses and the vertical stress of one year after the earthquake became more than the double before the earthquake. However, the magnitudes of the maximum principal of two year after the earthquake became smaller comparing with those of one year after the earthquake. Furthermore, the magnitudes of the intermediate principal stress and the minimum principal stress of two year after the earthquake became almost same as those before earthquake, and the vertical stress of two year after the earthquake became almost equal with the overburden pressure. And the magnitudes of three principal stresses of three year after the earthquake became the same level before the earthquake."

Jan 1, 2015

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By T. B. Williams

THE British Columbia Coal Control was established in 1946 as a branch of the Department of Lands. Its functions are the administration of the Goal Act, the making of field and laboratory investigations bearing on the delineation and utilization of British Columbia coal deposits, and the dissemination of information concerning them. The Department of Lands in the Province of British Columbia retains and administers many of the Province&apos;s resources until such time as they are actively developed under the departments of Agriculture, of Forests, of Mines, etcc. The work of the Control is one of stock taking and appraising. We are picking up where the geological surveys leave off. In an effort to assist in the orderly, scientific development -of our excellent and extensive&apos; ?Coat resources, we are bridging the gap between exploration and geological examination on the -one hand and mining on the other. All coal analyses required in the course of the investigations, together with? those requested by prospectors and others, are carried out in the very modern and efficient laboratories of the Coal, Petroleum, and Natural Gas Control. At its inception, the Coal Control began an investigation of coal seams in the Peace River area, specifically those contiguous to the Pine River valley about one hundred miles west of Dawson Creek. The occurrence of coal in the Peace River canyon, east of Hudson&apos;s Hope, bad been known since 1792, but the first record of production is for 1923.

Jan 1, 1951

By László Guczi1

Nanosize model gold particles with varying size were fabricated by deposition of a 10 nm thick gold film onto SiO2/Si(100) substrate by electron beam evaporation followed by modification using low energy Ar+ ion bombardment. The change in particle size were monitored by the Au 5d valence band states determined by ultraviolet photoelectron spectroscopy (UPS). The gold/iron oxide interface was studied by iron oxide deposition on gold. It was found that the energy profile of Au 5d valence band states are strongly redistributed with decreasing the gold particle size mostly affecting at the lowest and at the highest binding energies. The size effect in the UPS spectra can be interpreted by the energy redistribution rather, than by narrowing the 5d states. The iron oxide deposition increases the catalytic activity in CO oxidation whether it is on gold nanoparticles or on a continuous 80 nm thick gold film. The activity enhancement is significantly larger in case of gold nanoparticles. The interface interaction is operative in enlargement of the catalytic activity even if gold particles are not exposed to the surface, but they are located below the iron oxide layer.

Oct 1, 2003

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By S. Afshar, E. Dajoux, C. Allaire

For various reasons, molten salts, mainly chlorides and fluorides, are used in the aluminum industry. In the holding and melting furnaces, these salts may have different roles such as protecting the metal from oxidation, reducing the metal content of the skim or removing inclusions or impurities from the metal bath. However, the use of these salts may also have some undesirable effects such as easy attack of the furnace lining refractory materials by molten aluminum. The aim of the present investigation was to clarify and to compare the effects of chloride versus fluoride salts, on the corrosion process of the aluminosilicate based refractory materials. A laboratory test and procedure, simulating the conditions at the metal line in the aluminum treatment furnaces, was used. Different aluminum alloys (A1-5wt.%Mg, A1-5.5wt.%Zn and 7075 alloy) and chloride or fluoride salts (MgC12, KC1, CaCl2, NaC1, MgF2, CaF2, NaF and cryolite) were used as well as several aluminosilicate materials. Thermogravimetric measurements were also carried out in order to analyze the effect of the salts on the oxidation of molten aluminum alloys. The experimental results showed that fluoride salts are more aggressive than chlorides against the tested refractory products. It is postulated that the fluorides prevent the formation of a protective oxide layer on the metal surface, favoring at the same time the corrosion of refractories. Moreover, it was found that the presence of Na in fluoride salts increases significantly the aggressiveness of the aluminum alloy towards the refractory samples.

Jan 1, 2004

By Atulya Verma, Samantha Espley, Nashel Kalaka

Numerical modelling simulations of proposed mining sequences are used to evaluate mining induced stress concentrations and their migration associated with the progress of mining. This analysis is a standard practice for most prospective mining projects at various levels of feasibility study. The studies are usually initiated at the beginning of the mining cycle, on a global scale, and are maintained and updated throughout the life of mine (LoM) to identify or address local issues and the required remedies as and when needed. Developments in numerical modeling techniques along with advancements in computing technology and data storage/management capacity have given rock engineers access to a huge volume of data that needs to be analyzed and assessed. The most common approach to numerically evaluate stress concentrations and migrations in underground mines is to select the points of interest in a given volume such as the back of an excavation or points within pillars around critical infrastructure, and plot the stresses or a derivative of stresses over time to represent life of mine concentrations and migrations of stresses. The problem with this approach is the sharp gradient of stresses close to excavation boundaries. Slight changes in the location of selected points can change the stress concentration and migration patterns substantially and all generalized statements about LoM risk can be challenged in one way or another. For global stresses, the most common current approach of data analysis is by viewing series of pictures representing stress contours. In this approach, it is easy to overlook some critical detail and/or be masked by personal preferences of contour/picture representation. To overcome the problem of representing and analyzing huge volume of stress simulation data, the authors, through their experience at different mining operations, developed a volume-based technique to reliably evaluate mining-induced stress concentrations and migrations. The volume-based approach is for risk-based assessments of adjacent regions in the rockmass, in and around planned stoping excavations. The volume of interest is the entire ore body that is planned to be mined, but it could be just a part of the ore body depending on the specific use case. The risk identifiers are the induced stresses as compared to the strength of the rockmass. Over the LoM, the risk identifiers are tracked versus the corresponding excavation ratio of the zone. This approach is very effective in identifying the stages of mining that are contributing the most to the mining induced stress risk and the results can be used for proactive planning and mitigations measures such as alternative mining sequences, or stope sizes, or extraction methods. The approach has also been very successful in application at mature mines, particularly in assessing the re-initiation of mining in zone that has been dormant for some time. The volume-based approach allows for an assessment of the current state of the rockmass and the identification of future risks when planning resumption of mining activities.

Jan 1, 2023

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By S. H. Castro

Molybdenite depression by shear degraded polyacrylamide solutions has been investigated. Aqueous solutions of polyacrylamide-type flocculants were subjected to shear degradation under a range of high-speed stirring conditions. Settling tests, carried out with quartz slurries and sheared polyacrylamides, showed reduced flocculant performance with increased degradation. As the sedimentation rate is strongly dependent on the polymer&apos;s molecular weight, these results fit well with the shear degradation theory, which predicts the production of shorter chain segments due to breakage of the polymer macromolecules. Microflotation tests on natural molybdenite showed that the depressing ability of a commercial polyacrylamide flocculant remained unaltered after shear degradation, even when the flocculating ability was entirely lost. Practical implications of shear degradation on molybdenite flotation are discussed.

Jan 1, 2004

By Tibor Horvath

Dust abatement is possible on bulk materials, whether conveyed or stockpiled. Minimum (ppm) quantities of chemical additives can efficiently and rapidly control dust of conveyed substrates with no effect on floatation chemistry. Top coating of large surface areas can control surface dust and wind erosion. Environmental and toxicity impact must be considered in any treatment, especially on areas with percolation runoff, leachates, or limited containment. The most effective dust control is preventing release of substrate fines rather than trapping and removing air borne dust. Techniques to prevent release of fines from conveyed substrates will be discussed. Dust control dynamics are a very complex combination of solid phase physical and chemical interactions between the substrate and the fines. ?Smart Technology? products permit dust abatement of stockpiled substrates and tailing fields with no environmental impact. Using ?Smart Technology?, the dust abatement products remain active and can re-seal damaged areas. Efficient, low environmental and toxicity impact, dust control will be demonstrated through case studies where these principals have been applied.

Oct 1, 2010