Search Documents

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By D. W. Smith, J. J. Koskinen, T. A. Enwald, M. E. Ball

"A full-scale demonstration unit of Tampella's LIFAC desulphurization process was tested at SaskPower's Poplar River Power Station Unit No. I. The test program included a series of parametric tests, followed by a 1500 hour operational evaluation. This paper summarizes the results of the test program, and SaskPower's economic evaluation which led to selection of the LlFAC process for SaskPower's 300 MW Shand power station. IntroductionOne of the major influences on the coal mining industry today is public and legislative response to acid rain. When sulphur-bearing fuels such as coal are burned, the sulphur oxidizes to sulphur dioxid e (S00 which, if uncontrolled, enters the atmosphere as one of the by-products of combustion. S02 then combines with water in the air to form an acid and acid rain results. Combustion also produces nitrogen oxides (N0J which can combine with water in the air forming nitrogen based acid , also contributing to acid rain.Acid rain has become a significant international concern. Newspapers have reported on dying forests, dead lakes and crumbling statues. Papers also include articles professing that the physical results of acid rain are vastly overstated. In the United States, a IO-year, Y2-billion dollar study called the National Acid Precipitation Assessment Program (NAPAP) was commissioned to evaluate the effects of acid rain. Even this extensive scientific study did not resolve the controversy. Despite disagreement over the quantitative effects of acid rain, there is no doubt that public concern over the issue is widespread and deeply felt.In response to this concern, legislators throughout the world have reacted with programs that restrict the emission s o f SO, and NO,. To industries involved in the supply and use of coal, the impact of these legislative programs has been extensive. United States power plants will be spending 10 billion dollars in the next decade for flue gas clean-up equipment. Even all this new equipment will not stem the tide of change to low sulphur coals and to “clean “natural gas. The following summarizes legislative actions taken for Canada and the United States."

Jan 1, 1993

By C. Ciriello

Six Sigma methodology, as applied within Xstrata (formerly Falconbridge and Noranda), involves a disciplined approach to managing projects, solving problems, improving performance, and leveraging information. The four (4) cornerstones of Six Sigma are the use of Philosophy (customer driven, desire to improve and discipline), Metrics (measurement systems), Methodology (scientific method and sequence of deliverables), and Tools (such as statistics, change management, and root cause analysis). This paper will outline the general steps of the Six Sigma methodology and demonstrate how each phase directly applies to a real plant metallurgical project aimed at reducing nickel losses of the rougher flotation circuit at Raglan. The main concepts of Six Sigma are described, along with the specific challenges, successes, and deliverables related to the project. It is also the authors' aim to demystify the basic Six Sigma principles.

Jan 1, 2007

By Lloyd Buckingham

"The operating cost of a gold mine employing granular activated carbon to recover gold can be greatly affected by the condition of in-circuit carbon and its attrition losses. To accurately identify and quantify carbon losses requires careful study. Carbon attrition in the mill can be attributed mainly to physical or mechanical breakage due to the transfer of carbon in the circuit and to carbon oxidation and thermal fracture occurring in the carbon reactivation kiln. Of the equipment involved in carbon transfer, the water powered eductors are the major cause of abrasion and should be replaced with pumps or alternate methods that can serve the purpose. This paper also reviews the impact of carbon stripping and washing on overall operations.IntroductionHolt-McDermott Mine operates a 1360 tonnes per day Carbon-in-Leach (CIL) mill to recover gold. The relatively high carbon consumption and high remaining gold values on carbon after stripping were viewed as a challenging project for research. Extensive metallurgical testwork was initiated to reduce these values. Figure 1 below indicates the carbon flowchart prior to any significant changes in the carbon handling procedures.Carbon consumption after commissioning which was as high as 10""/o of carbon eluted, has been brought down to less than 5%. Changes that brought about this 50% reduction in carbon consumption are:1 ) Improvements in kiln operation2) Elimination or replacement of eductors3) Reduction in tonnes of carbon eluted"

Jan 1, 1994

By Larry M. Southwick

There have recently been executives at major metals companies who have recommended that Greenfield Projects not be pursued. Greenfield includes not only new geographical locations, but also new technologies and new types of feed materials. In the middle part of the 20th Century, two such projects were successfully commercialized to recover nickel from Cuban lateritic ores. One project (at Nicaro) used the Caron ammonia-ammonium carbonate leach and the other (at Moa Bay) a high pressure acid leach. How both of these projects dealt with these Greenfield issues will be reviewed, based on the original reports that described the research and development of the plants. This study will include a review of the critical ore characterization and sorting issues, as well as the extractive metallurgical, product recovery and equipment selection and sizing problems and how they were solved at each stage of project development, from laboratory through one or more pilot scale plants to start up and operation. In one case, a major revision of the plant was made after several years of operation to correct operating, equipment selection and materials of construction problems that hindered economical operation. These descriptions will provide a guide through the complicated and critical issues that in recent times have caused many companies to give up on similar development. Even with the more advanced analytical and computational tools available to today’s mineralogists, engineers and metallurgists, the basic concepts with which these projects successfully addressed their sets of problems are still required. In addition, upper management, now perhaps further removed from hands-on experience than was common then, will see how complicated problems require intense and detailed effort to avoid failure in the field and capital blowouts. Build it and we will make it run, kicking the can down the road and borrowing operating and design concepts incorrectly on technological issues, or nine year olds on a sugar high making financial decisions are not philosophies by which to succeed with Greenfield Projects.

Jan 1, 2014

By G. A. Gillett, C. F. Bonney

"The Davy McKee combined mixer-settler (CMS), is a liquid-liquid contactor, which has been commercially applied to the recovery of uranium from dilute sulphuric acid-bearing leach liquors. CMS differs from most other solvent extraction systems in that the mixing and separation of the phases is carried out in the same vessel.IntroductionTypical solvent extraction plants for the recovery of uranium operate at organic to aqueous feed flow ratios of 1 : 2 to 1 : 30. Because it is beneficial to mix the organic and aqueous phases at an organic/aqueous (O / A) ratio of between I : 2 and 2 : I there is incompatibility between the over-all and operating O /A ratios.Conventional mixer-settler designs require an external recycle of the minority flow which results in the possibility of over-mixing, increased settling requirements and entrainment losses. Other workers have approached this problem in terms o f enhanced sett ling and this has been partly successful.Davy McKee's approach involved a radical rethink of the principles of liquid-liquid contact and separation.Description of CMSThe CMS has the important advance that the required mixing O/A ratio can be achieved without external recycle and is not affected by the O /A ratio of the feeds. Three zones co-exist within the CMS unit-a central mixing zone and upper and lower separation zones. A pump impeller on a draught tube is installed within the mixing zone and baffles are installed above and below the mixing zone. Conventional mixer- settlers have several undesirable features which ca n largely be eliminated using the CMS system:"

Jan 1, 1983

By R. Heikkilä

Fluent information exchange between different work phases, software and systems used in infra construction is a key for successful execution of infra construction projects. Open and publicly available information formats with the determined data models aim to facilitate the interoperability between different software and systems developed by competitive vendors. While building and construction industry has developed and used IFC format for years, infrastructure sector has just recently started to target clear efforts on the development of open information formats for infra construction processes. In the paper, a new Inframodel3 extension just developed in Finland and based on the LandXML1.2 international standard is to be introduced. The aim of the Inframodel3 was set to meet the requirements of information transfer needed especially between BIM based design software, measurement systems and 3-D machine control systems used in road, railway and watercourse construction projects. Some test results are reported and evaluated in the paper. In the field of bridge engineering, the IFC format and IFC Bridge extension have been tested and evaluated in Finland. The results from the experiments show and verify as well the applicability of these open formats to the information exchange requirements in bridge engineering. The current limits for open information transfer of these formats are shown. The active co-operation with the International Building SMART Organization has led to the achieved status and position for both the Inframodel3 and IFC Bridge formats and hence the continuing international support provided by Building SMART.

Aug 1, 2013

By W. L. Single

"LET ME FIRST OF ALL thank you for sending this invitation to me to participate in this Annual Meeting of The Mining Society of Nova Scotia. As an engineer, although I don't get an opportunity to practice very much engineering these days, I am, of course, always pleased to be able to meet with my fellow engineers to exchange views, but I must admit that today I feel a little bit out of place in the midst of all the experts that are here today. Let me make one thing clear - I'm a generalist! Your program states that I am to make a keynote address. I have always thought that a keynote speech is one that says something that has not been said before - announces some new program or policy, or says something startling. I am sure you will understand when I tell you that keynote addresses are made by politicians and that civil servants speaking publicly are usually expected to give an account of what is, or what is likely, to happen as a result of policies that have been announced in keynote speeches by politicians. I am reminded of a statement by a distinguished parliamentarian who said, ""However exalted a civil servant may be, he is not above the elected officials."" So today I will confine myself to giving you an overview with particular emphasis on the development side of oil and gas. The theme of ""Oil and Gas"" is a topical one these days. I suppose it's because of all the copy that is being generated by the media on the U.S. energy crisis, the Mid-East situation, the fact that most of the world's proven oil reserves are in Arab hands and, of course, the accelerated exploration activity that is taking place in the North Sea, in the Arctic, and off the coast of Newfoundland and Nova Scotia."

Jan 1, 1973

By N. Vayenas, G. Yuriy

"The combination of a predictive reliability assessment model and discrete-event simulation can be an effective methodology to study the impact of equipment failures on the capacity of production systems in mines. In our case, a predictive reliability assessment model using genetic algorithms is combined with a discrete-event simulation model to analyze mine equipment systems.Discrete-event simulation involves modelling of real-life systems based on variables and events that occur or change at distinct points in time. The Simul8 simulation software, by Visual Thinking, is used in this research. It is a two-dimensional (2D), discrete-event simulation/ animation software tool for creating realistic depictions of manufacturing and materials handling systems.The simulation model developed for the purpose of this research represents a typical two-level, sub-level stoping section of an underground mine in the Sudbury region in Ontario, Canada. This 2D model was created to assess the impact of equipment failures to a mine’s production throughput. In more detail, using mean time between failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity.Another purpose of this research work is to demonstrate how low-cost simulation tools such as Simul8 can be successfully applied to model underground hard rock mining operations. The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL)."

Jan 1, 2005

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

Heap leaching accounts for around 20% of the global production of copper. In heap leaching coarsely crushed ore particles are contacted with an aqueous lixiviant percolating through large packed beds (heaps) of the ore particles, with the loaded solution collected at the foot of the heap for metal recovery, solution make-up and recycle. While dominant for copper oxide acid leaching, it finds application also in copper sulphide (bio) leaching. Despite their apparent simplicity, heaps are in fact complex chemical reactors in which a number of competing sub-processes determine the overall rate of metal extraction. Therefore, meaningful prediction of copper production rates from heaps, as well as operational optimisation and control, all hinge on a comprehensive and quantitative understanding of these complexities. The paper gives a comprehensive overview of the various sub-processes in copper heap leaching and their interactions, including those relating to mineral-particle-solution-gas phase interactions at the micro-scale bulk transport and distribution of solution in unsaturated dense beds at the macro-scale. On the basis of a more fundamental understanding and modelling, the potential for optimized operation offers new opportunities for the extraction of value from both low-grade and complex polymetallic ores. INTRODUCTION Heap leaching is one of the percolation leaching technologies, which includes in situ leaching, dump leaching, heap leaching and vat leaching (Bartlett, 1998). The common phenomenon in all these technologies is the transport of leach solution through a fixed bed of ore particles, which interacts with the solid as it migrates along its path. The target minerals are released into solution and with its flow are carried out of the bed. The targeted dissolved metal species are recovered from solution through various hydrometallurgical techniques, especially solvent extraction (SX), before the barren solution is returned to the leach process. Heap leaching is practised in three main types of applications: sulphuric acid leaching of copper oxide ores, cyanide leaching of gold ores as well as the oxidative acid leaching of secondary copper sulphide ores, usually with the assistance of certain microorganisms and, more recently, in the presence of chlorides (CaCl2, sea water). While gold heap leaching dates back to the 1960s, large scale copper heap leaching commenced in Chile from the 1980s, and sulphide heap leaching emerged essentially as a consequence of acid leaching from mixed oxide/sulphide ores from the 1990s (Watling, 2006).

Jan 1, 2019

By Forrest A. Kerr

Introduction During recent years the work of the Geological Survey in northwestern British Columbia has been in the nature of reconnaissance and exploratory mapping, largely for the purpose of gaining knowledge of the potential mineral-producing zones known to occur along the eastern side of the Coast range, and also to gather such data as might facilitate their exploitation. Commencing with fairly detailed mapping in the more accessible parts, the work has been continued and expanded until now an understanding has been gained of the more general features of a continuous section along the range for a distance of about two hundred miles. Geographically, northern British Columbia is more or less isolated. It is cut off from the central part of the Province by a rugged and mountainous country which, except for the telegraph line and a rarely travelled trail along it, is not penetrated by any developed routes or lines of communication. To the west, it is cut off from the Pacific by the Coast range, an extremely rugged area sixty to eighty miles in width which, except along the few navigable rivers cutting across it, cannot be readily traversed. Politically, it is further isolated in this direction by the narrow strip of south-eastern Alaska which borders the coast and extends inland to the axis of the range.

Jan 1, 1931

By A. Mcdonald

"An X-Met Analyzer was purchased from Outokumpu in late 1983for use in the Hudson Bay Mining and Smelting smelter. Its first use was in the fuming plant to give zinc assays of each charge of slag tapped from the fuming furnaces. This quickly told the operators exactly when each charge had reached its economic tap-out point, and gave supervision a fool-proof method of identifying good operation. These and other factors led to major improvements in coal utilization in the fumers and to major increases in zinc oxide production. A second unit was later purchased for the reverberatory furnace to give silica and iron assays of the slag, and these were used to make adjustments in the feed composition to maintain the desired SiO2:Fe ratio in the slag. Since purchasing the units for the furnace, the oil consumption and copper content of the slag have dropped significantly. IntroductionSmelters have lagged far behind concentrators in process control by mean s of rapid product analysis. The on-stream X-ray analyzer was developed about seventeen years ago, and soon concentrators around the world were getting assays of the incoming ore, .concentrates and tailings every fifteen minutes, and using these to control reagent additions and other process variables. Almost always, the concentrate grade and recovery improved.In smelters, product streams are solids or molten materials, not the more easily handled slurries, and until seven years ago no inexpensive equipment was available to provide rapid analysis of this type of material. In approximately 1980, several companies developed instruments based on irradiating solid samples with low-intensity gamma rays from radio-isotope sources, and measuring the secondary X-rays emitted from different elements in the sample to provide an analysis of the elements desired.The smelter staff had a close look at what was needed and listed the following points as being critical:1. ability to provide Zn assays of a sample of slag within 15 minutes of taking it, in order to achieve optimum fuming times (zinc fuming , being a batch process, had the greatest potential benefit from rapid slag analysis);2. ability to give Cu and Fe assays on the slag, and on other smelter products, such as matte and converter slag;3. ability to give Si02 assays since the SiO2 content of the slag has a strong effect on fuming rate; and4. ability to stand up to an industrial atmosphere such as exists in the fuming plant."

Jan 1, 1987

By A. A. Burgoyne

"The McDame chrysotile asbestos deposit located near Cassiar in northern British Columbia isfound at depth and on trend to the southeast of the currently mined open-pit Cassiar asbestos deposit. The ultramafic rock hosting the McDame is serpentinized peridotite of the Upper Paleozoic Sylvester Group contained in an ophiolitic sequence preserved within a lower thrust sheet of the Sylvester Allochthon. The Sylvester stratigraphic package is a series of thrust slices composed of argillite, tuff and volcanic flows, diorite and serpentinite. Contacts between units are often fault-controlled.The McDame asbestos-bearing ultramafite is considered to represent a separate interleaved fault-bounded slice of rock distinct from the Cassiar asbestos deposit.Asbestos mineralization of the McDame deposit was discovered in /978. Exploration during /980 and /98/ focused on extensive underground drilling of the deposit and in /983 on geological mapping, airborne and ground magnetic surveys. In /984 a 622.5 m borehole was drilled with a 242 m intersection of McDame ultramafite of which the lower 15/ metres contain potentially economic chrysotile asbestos. The McDame deposit averages 90 m thick, trends north-south, dips easterly and plunges southeasterly. The deposit is estimated to contain geological reserves in the order of 62 million tonnes containing asbestos fibre similar in value to the Cassiar deposit.The McDame is considered a major world-class asbestos deposit. A decision to develop and mine the deposit will require further substantial underground exploration and evaluation. A + 1200 m exploration adit driven to the hanging wall of the deposit was undertaken in 1985 in anticipation of bulk sampling and diamond drilling in 1986."

Jan 1, 1986

By F. E. Lathe

The method of feeding blast-furnaces to be described below is simply the application of well-known principles, and an attempt to carry that application to its logical conclusion. It does not involve radical changes in equipment, nor does it require unusual skill on the part of the furnaceman. In fact, much of its value lies in its very simplicity. Before giving details of the method it will be well to consider briefly the conditions under which it was used at the Nickelton plant of the British America Nickel Corporation, in the Sudbury district, before that plant closed down. The Sudbury nickel ore consists chiefly of pentlandite, chalcopyrite and pyrrhotite in a gangue of norite or greenstone. The proportions of sulphide and gangue vary widely in different mines, the former constituting about 45 per cent of the total in the British America sorted ore. The gangue is fairly uniform in analysis, carrying about 55 per cent Si02, 18 per cent A120 3, 13 per cent FeO and smaller quantities of CaO, MgO, Na20 and K20. The ore has been frequently described as refractory, a word which seems suitable when one considers the many unsuccessful attempts to smelt it pyritically, as well as the high percentage of coke normally used at all the plants in the district.

Jan 1, 1925

"This document establishes standards and guidelines for scientific and technical disclosure by Issuers listed on the TSX Venture Exchange on their mineral properties. It incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.1. Introduction1.1 General(a) This Appendix establishes standards and guidelines for scientific and technical disclosure by Issuers on mineral properties. These standards and guidelines should be applied prudently and with common sense by those Issuers in conjmction with the applicable requirements of section 1.2.(b) This Appendix incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and -written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.(c) This Appendix is not intended to be exhaustive or all-encompassing and greater detail may be appropriate and required in certain situations. Issuers are encouraged to contact Exchange technical staff where they are not certain about the requirement for disclosure on mineral properties."

Jan 1, 2003

By K. Miao, W. Mu, M. Sharma, A. Haas, N. Dogan

"The ever increasing demand for cleaner steels with low inclusion content has highlighted the limits of our current knowledge for controlling and predicting inclusion agglomeration and removal during liquid steel processing. Key knowledge gaps in this area result from the complex nature of the problems associated with measuring and visualizing the phenomena studied. Confocal scanning laser microscope (CSLM) allows for continuous in situ observation of micron-size samples in real time, at high resolution, under conditions relevant to the steelmaking process. This paper summarizes some of recent CSLM applications in our laboratory to illustrate the methods of analyzing transient behavior. The reaction between inclusions and slag is given as an example. The dissolution rate of calcium aluminate inclusions in CaO-SiO2-Al2O3 slags has been studied at elevated temperatures: 1500, 1550 and 1600°C as well as thermodynamic/kinetic analysis. It is found that total dissolution time decreased with increasing temperature. The rate limiting steps are discussed. It is shown that the diffusion through a product layer is responsible for dissolution at 1500°C. At higher temperature, dissolution is most likely controlled by both boundary layer diffusion and chemical reaction at the slag-inclusion interface. In this paper, the evidence for and against the theory will be critically examined and repercussions of the theory to steel refining processes will be discussed.INTRODUCTION Inclusion formation during liquid steel refining is an unavoidable consequence of current ladle steelmaking processes. The nature and quantity of the inclusions formed in steel is critical in steelmaking, as it affects both productivity through clogging, and downstream physical properties of the steel. It is therefore crucial to better understand and control the formation, agglomeration and dissolution behaviour of inclusions in a slag in order to improve the removability of inclusions from liquid steel. Most research (Sandhage & Yurek, 1988; Sandhage & Yurek, 1990a; Sandhuge & Yurek, 1990b; Sandhuge, 1991) relevant to the kinetics of inclusion removal has been obtained by using a technique where simulated inclusion material (ceramic rods) is dipped in slag and the dissolution rate is measured. While much has been learned using this approach, the difference in scale from bulk materials to inclusions is likely to have a significant bearing on the dissolution kinetics of inclusions in a slag and will certainly result in a very different influence of capillary effects. Further, the data obtained using an indirect (dip test) procedure relies on a comparison of the initial and final conditions of a sample rather than in-situ observation which can be achieved in a confocal microscope in real time."

Jan 1, 2017

By R. P. Taylor

"This paper covers the development of the property to its present production level of20,000 tonnes per day from the Valley Mine. It will also review the analysis of various case studies for the expansion of the project to its full potential, and discuss the impact of the recent structural change in the copper market on the development of a large low-grade deposit such as Valley.IntroductionIn 1964 Cominco participated, along with a number of other companies and individuals, in the formation of Valley Copper Mines Ltd. This company was formed in order to facilitate exploration on a large number of mineral claims held by these parties in British Columbia's Highland Valley, approximately 400 km northeast of Vancouver (Fig. I). Cominco 's ownership of Valley Copper was gradually increased over the years bot h through shares gained for exploration expenditures and through shares purchased on the open market. By the mid- 1970sCominco' s interest in Valley Copper exceeded 80%.ExplorationExploration from 1964 to 1969 led to the discovery of a massive porphyry copper depo sit now known as the Valley orebody. A claim boundary divided the deposit with 80% of it on Valley Copper claims and 20070 on claims held by Bethlehem Copper which was already mining adjacent copper orebodies. During the period when the Valley ore body was discovered, exploration by other companies resulted in the discovery of the large Lornex and Highrnont deposits nearby. The stage was now set for the Highland Valley to become an important copper-producing area (Fig. 2)."

Jan 1, 1986

By A. J. Hargraves

"It is difficult to quantify comparatively the gassiness of a property. The most common index to gassiness, cubic feet of gas per ton of coal mined, is very arbitrary and does not take into account the geological setting nor the mining operation. The gassiness of a virgin coal in situ can be assessed, but no method is precise and the most accurate methods involve prolonged field and laboratory experiments. In general, gassiness increases with depth. Whereas 'gas' normally implies methane, other gases such as nitrogen, carbon dioxide, etc. may be present in seam gas also. The inflammability of methane is a problem, particularly the explosibility of a methane-air mixture; also oxygen dilution is involved in high gas concentrations and some gases are poisonous even in low concentrations. Cross measuring into a virgin seam is usually not as troublesome as development in the seam, where narrow openings may require strong ventilation to dilute gases exuding from the face and sides. Total extraction presents problems of gas from the working seam, or from adjacent seams, particularly at the return side, or of gas-laden air from the goaf streaming out or sometimes surging out intermittently, again on the return side. In pillar extraction or longwall retreating special roadways may be required to allow the side-to-side and end-to-end flushing of the goaf which is somewhat inherent in longwall advancing. Layering may occur, particularly where ventilation conditions are not brisk. Outbursts of gas from adjoining seams may be induced by sudden rupture of roof or floor in caving workings. Outbursts of coal and gas from the working seam may occur, mostly in development work, under special environmental circumstances. Gas problems may be reduced or eliminated by predrainage of gas ....:. rarely successful from the working seam - usually undertaken from adjoining seams prior to escape of gas released by caving. The ideal solution - general predrainage of gas to the surface from measures prior to mining - has yet to be accomplished. • In the planning of gassy mines it is possible to make an assessment of gas contained in the seams and to estimate what proportion will be released into the mine air, but emission of gas into mine workings is never steady and at present there is no better planning criterion than experience at the mine next door!"

Jan 1, 1973

By R. L. Bruening, R. M. Izatt, N. E. Izatt, S. R. Izatt

"Molecular Recognition Technology (MRT) is a simplified, green chemistry process with applications in selective separations of Ni(II), Co(II), and platinum group metals in primary ore beneficiation processes and secondary recovery operations from spent products, scrap, and environmental waste solutions. Simplification in MRT processes is achieved by non-use of solvents, reduced space requirements, and a simple separation system involving columns packed with metal-selective SuperLig® resins. Minimal waste is generated and metal recovery is achieved at 99% levels from g L-1 to <mg L-1 concentrations. MRT systems are attractive technologically and economically compared with solvent extraction, ion exchange, and precipitation separation processes. Commercial examples of MRT use include removal of impurity metals Cd, Cu, Ni. Fe, and Pb to mg L-1 or lower concentration levels from Co streams to produce battery-grade Co. Highly purified Co is required for optimal function of lithium ion rechargeable batteries and superalloys associated with aerospace and gas turbine operations. Impurity metals are recovered for reuse or proper disposal rather than being discarded to landfill. Green chemistry processes, such as MRT, are needed in metal separations going forward into the 21st century to achieve global metal sustainability in processing of native ore and treatment of secondary sources.INTRODUCTION Maximizing efficiencies of metal separations and optimizing metal recovery rates during separation processes are important goals on the road to achieving metal sustainability. Achievement of these goals is consistent with stated principles of green engineering (O'Connor, Zimmerman, Anastas, & Plata, 2016) and green chemistry (Anastas & Eghbali, 2010). Molecular Recognition Technology (MRT) separation processes using SuperLig® resins have a 25-year record of performing competitive, commercial metal separations with metal recovery rates approaching 100% (Izatt, Izatt, Izatt, Krakowiak, & Bruening, 2017). SuperLig® resins are characterized by high selectivities for specific metals over concentration ranges from g L-1 to mg L-1 or lower. MRT systems use no solvents and are simple in design and operation resulting in reduced capital and operating expenses."

Jan 1, 2017