Search Documents

By F. Urekar, R. B. Pankhurst

"Air spaces and air gaps in an explosives column are known to allow greater distribution and cushioning of explosive energy from the rock mass. This energy distribution is enhanced if the explosives ' gases can be confined in the borehole for as long as possible by plugging and stemming above the air space.Power Plug is an inflatable plug which can seal a borehole at any point to separate the stemming from an air gap and explosive toe load.IntroductionThis paper will discussion-going work by C-I -L Inc. and operators of two open pit mines to study the results of using Power Plugs:I. Pit wall stability - the authors have found the Power Plug effective for wall control blasting in open pit mines.2. Selective mining of coal seams - the authors work shows the Power Plug allows mining selective coal seams by predrilling underseam waste wedges.Pit Wall StabilityWall stability in an open pit mine is essential for safety. Good wall stability can be achieved with wall control blasting techniques which cushion the effect s of the explosives charge by decoupling the charges from the borehole wall. The usual method of decoupling a charge in a large-diameter rotary borehole is to load the explosives in tubes (Fig .I) . We now believe the air deck system is effective in sea ling a borehole above the explosive charge to create an air deck within the borehole which will cushion the blast.In a linear decoupled charge, an air annulus surrounds the explosives charge and cushions the effects of detonation genera ted gases on the pit wall. In an air deck, i.e. with the hole plugged at the collar, the gases genera ted by an explosive toe load are sealed in the empty borehole column. After a period of time, these trapped gases produce radial cracking between holes along the entire length of the borehole.It is common practice to employ de coupled explosive charge columns in the borehole to limit blast damage to surrounding rock. The exact mechanism of energy transfer in such blasts, however, is not well understood. Interruption of the continuous explosive column in a borehole by means of stemming, or air decks, may also be viewed as another form of decoupled blast. Decoupling of the explosive charge from the borehole wall affects both explosive energy release and explosion pressure developed in the borehole."

Jan 1, 1988

By P. A. Mascaró, N. Chacon, A. A. Cecchi

"This document shows the development of a system called the “On-line charge level determination in SAG mills” (abbreviated as Jc). The Jc variable has certainly been difficult to measure due to the relevant number of factors and variables that affect the grinding phenomena inside semi autogenous (SAG) mills. To assess the feasibility stage of the proposed system, it was necessary to carry out two tests in different sized SAG mills, 38´ × 22´ and 36´ × 15´, respectively. In each test, the system was configured with a battery of sensors of the following types: (1) strain gauge, (2) accelerometer, and (3) gyroscope. The first step involved for charge level determinations was to determine kidney foot and shoulder by means of a study of the energy-impacts on shell structures. The second step consisted of correlating the measured grinding operational variables with the actual charge levels obtained from SAG mill crash stops. This system development is extremely useful and relevant for providing approximations about mass balances inside SAG mills. It will be a suitable tool for explaining “tonnes per hour” variations and determining optimal points under various operating conditions.INTRODUCTIONThere has been a growing necessity for technologies capable of obtaining “on-line data” of the main comminution variables in order to increase throughput. Computer systems have taken an important role in providing important solutions by means of processing on-line device signals (commonly referred to as monitoring). In semi autogenous (SAG) milling, there are many examples of monitoring devices that allow the operational staff to obtain detailed information both mechanically and electronically inside a grinding circuit. In this context, a new technology has been developed to obtain “Jc total charge (%) online” in two different SAG mills called Vibro-Energy® System.As part of the analysis performed by JKsimMet® the Jb/Jc was estimated because it has an important impact on SAG mill throughput. Different scenarios were simulated and contrasted at various theoretical Jb/Jc values in a baseline circuit (Figure 1)."

Jan 1, 2016

By M. G. Goudge

IT IS ENOOURAGING indeed to note during the past year that, despite a slackening off in many markets and with numerous major difficulties and problems to solve, the mining industry of Nova Scotia was maintained at a very high level. The value of the Province's mineral production for 1957 amounted to approximately $65,000,000. This represents a drop of only 1.5 per cent from the figure of the previous year. Coal Atlantic Collieries, Ltd., opened a new coal mine during the year at Bras d'Or. This colliery is equipped with the most modern type of mechanical equipment available, with transport of the ?coal by a belt-conveyor system. Other mines in the Province continued to mechanize their operations by the addition of Diesel haulage locomotives and other mechanized mining equipment. New wash plants are in operation and .an additional one is planned.

Jan 1, 1958

By J. P. Messervey

THE story of the efforts made by the Department of Mines of Nova Scotia in the search for and investigation of mineral resources for the Canadian war effort began in the spring of 1937. During the past five years, however, heavy enlistments in the Active Service Forces by employees of the mining industry of the Province caused a recession in the production of coal, salt, and other essential minerals required to keep industry rolling on a wartime basis. A marked increase was shown during the period in prospecting for 'strategic' minerals, not only by individuals but also by some of the foremost mining companies. The Provincial Government offered encouragement in this field of endeavour by the enactment of legislation whereby the prospector was enabled to secure the maximum area of ground in a prospecting license at a minimum of cost. The labour requirements on the ground staked, however, remained unchanged. The Nova Scotia Department of Mines continued active investigation of minerals vital to the war effort. These included fluorspar, barytes, diatomite, limestone, and coal. Fundamental knowledge concerning the geology and mode of occurrence of these minerals was accumulated and extensive diamond drilling was carried out on the promising occurrences. Work in these fields is being continued.

Jan 1, 1945

By Joël P. T. Kapusta, Liam J. Watt

The last extended copper smelting and converting survey dates back to the 2003 International Copper Conference held in Santiago, Chile. The following year, the Minerals, Metals, and Materials Society of AIME (TMS) started a new series in its Journal of Metals (JOM) called JOM World Nonferrous Smelters Survey devoting its first Part to Copper. The copper smelting landscape has significantly changed in the past 15 years, both in geographical terms with the shift of copper smelting production from the Americas to China and in technological terms with the growing adoption rate of Top-Submerged Lancing (TSL) technologies and the development and implementation of Bottom-Blowing technologies. A copper smelting survey update, even if not as in-depth as the 2003 Copper Smelting Survey, is therefore in order. The authors will review the latest trends in copper smelting technologies and production worldwide in comparison to the landscape of the early 2000s. INTRODUCTION This 2019 copper smelting survey is different from previous surveys as our data does not originate exclusively from responses to a questionnaire sent to all the copper smelters. Our data comes from several sources. We are therefore very thankful to the International Copper Study Group (ICSG) and Wood Mackenzie for sharing some of their information and to ENFI, Outotec, and Glencore Technologies for helping us cross-check our numbers for the Chinese smelters, flash smelting, Ausmelt, and Isasmelt technologies. Our survey presents data reporting from a total of 96 operating copper smelters from around the globe, which is significantly higher than the 50 surveyed in 2003. Although secondary smelting numbers have steadily increased over time, this paper focuses on primary smelting operations with copper concentrate as feed material. The list in this survey is still far from complete, with missing information from several known smelting operations. The total primary copper production tonnage of the smelters we surveyed amounts to 18.3 million metric tonnes from 29 countries representing 92% and 94% of total world primary production for 2018 estimated by ICSG and Wood Mackenzie, respectively. This representation has increased from 2003 when the total was 9.71 million metric tonnes from 23 countries accounting for 73% of world production. The trends presented and analyzed within this paper have stronger significance because of the increase in production accounted for. The Chinese and Russian smelter information collected is more detailed than years past. Our complete dataset is summarized in Table 1 at the end of our paper.

Jan 1, 2019

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By F. J. Hrach, K. P. Flynn, P. J. Miranda

"ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. Separation results are presented for selected industrial mineral sources. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.INTRODUCTIONThe lack of access to fresh water is becoming a major factor affecting the feasibility of mining projects around the world. According to Hubert Fleming, former global director for Hatch Water, “Of all the mining projects in the world that have either been stopped or slowed down over the past year, it has been, in almost 100% of the cases, a result of water, either directly or indirectly” (Blin et al., 2013). Dry mineral processing methods offer a solution to this looming problem."

Jan 1, 2016

By L. A. Homeniuk, R. Bonnar

"The Athabasca Basin has been the scene of an intense exploration effort since the late 1960s, resulting in the establishment of this area as one of the major uranium districts in the world.The A thabasca Group is of Helikian age and unconformably overlies metamorphic rocks of Aphebian and Archean age. Most of the known uranium deposits have a close spatial relationship with the unconformity, graphitic meta-sediments, major northeast-trending structures and the basin edge. It should be noted that, in regard to the latter, some of the Cluff Lake deposits are exceptions.The pre-Helikian rocks underlying the Athabasca Group have been divided into six Iithostructural domains. The known uranium deposits are concentrated in the Wollaston and Mudjatik domains in the southeastern portion of the basin.The orebodies typically have a narrow high-grade portion below the unconformity and a broader, lower-grade disseminated zone in the overlying sandstone. Over-all grades average over 1% U3O8 and our estimate of known reserves totals more than 400 million pounds of contained U3O8. Some of the deposits have high concentrations of other metals, including nickel, arsenic, cobalt and gold. Ubiquitous chlorite and clay alteration is characteristic of the orebodies.Other Proterozoic basins in Canada of similar ages and having analogous geological settings to the Athabasca have received far less attention. Although little of the known uranium mineralization in these basins is related to the Helikian unconformity, there may be an exploration potential for deposits similar to those of the Athabasca basin.IntroductionThe Athabasca sedimentary basin is located within the Churchill Structural Province of the Canadian Shield in Northern Saskatchewan. The basin is elliptically shaped and is approximately 800,000 square kilometres in area.The objective of this paper is to summarize the various elements in the genesis of the unconformity-type uranium deposits of the Athabasca Basin and to evaluate the comparative potential of other Proterozoic basins to host similar unconformity-type deposits."

Jan 1, 1982

By M. McKim

"Due to the fact that there were no formal papers submitted for this session we can only print the discussions of the papers. a) Maqnetic Mill Liners : M. MckimE. MarcotteFalconbridge LimitedReplyIn looking at the slides on magnetic mill liners a question comes to mind, particularly in the case of a large diameter mill using large grinding media, concerning the potential hazzards which may exist from large chuncks of steel hanging in the mill. Would you comment.The magnetism was sufficiently strong from liner to liner to hold ........................ .(We are sorry but we could not transcribe the full reply to this question as no microphone was used by the speaker and i't was impossible for us to complete the rest).·"

Jan 1, 1984

By D. Mark Richards

Highland Valley Copper is a large open pit copper mine in the southern interior of British Columbia. Machine guidance technology using the Global Positioning System (GPS), was first implemented at the mine in late 1996 for blast hole drill navigation. The purchase of a third BE49R drill in 1998 completed the change to GPS navigation for all the mine?s drilling. The acceptance of this technology was almost immediate at both the operator and management levels. With the purchase of a new P&H 2800 shovel in 1997, the opportunity was taken to extend GPS navigation to a shovel. Due to communication restrictions, this was not as successful as envisaged. In late 1999, following a cost benefit analysis, a three-shovel trial of Caterpillar?s Computer Aided Earthmoving System (CAES), was initiated. The trial was successfully concluded in June 2000 and a further two shovels were equipped. Acceptance of this system has been very good at all levels, which has undoubtedly contributed to its success. In September 2000, CAES was extended to the dozer fleet with the purchase of a new track dozer. The CAES equipped dozer is used for pit production and project work. It is planned to extend CAES to the rest of the shovel fleet in 2001, along with a production front-end loader and one or two more track dozers.

May 1, 2001

By A. J. Sinclair

"Abstract-Geology contributes essential information toward obtaining high-quality resource/reserve estimates. In this context, geology can be considered under the following overlapping topics: regional geology, detailed (deposit) geology, mineralogy, ore deposit models and continuity, with geological mapping being fundamental to all. Each of these topics is considered here in terms of potential contributions to "improved" mineral inventory estimation. Some of the principal conclusions are:1. Regional geological relations must be consistent with deposit geology. It is common that important geological relations are more clearly evident in various regional locales than in highly altered and/or highly deformed mineralized areas containing mineral deposit.2. Detailed geology provides information for a geometric model of a deposit, a model that serves as a basis for mine planning. It is important to distinguish fact from interpretation in such models. Substantial effort is required to characterize the geometric margins of a deposit and the relation of these margins to the simplistic geometric form that normally emerges as an interpretation.3. Mineralogical studies relate to many aspects of deposit evaluation including abundance of ore and deleterious minerals, spatial distribution of ore and deleterious minerals, grain size characteristics of important minerals, mill design, etc.4. Ore deposit models contribute substantially to confidence in developing a three-dimensional geometric model of a deposit for mine planning. Specifically, they are a basis on which to develop rules for interpolation and extrapolation of ore, and they contribute to recognition of domains, each with its own characteristic continuity and margin character.5. Continuity is dependent on mineralization style and may be controlled structurally and/or chemically. It is important to distinguish geological continuity and value continuity. A wide range of classical geological methods are useful in examining geological continuity; value continuity is best viewed as a statistical characteristic that is quantified by any of several measures of autocorrelation."

Jan 1, 1998

By F. Hosseini

Shaping of metals by thixoforming relies on the unusual flow behavior of semisolid slurries containing nondendritic solid phase. The Flow behavior of metallic alloys containing both solid and liquid phases is investigated in the low solid fraction range (, 55%). This behavior depends on both the solid fraction and the shear rate. Four different shear rates is applied using back extrusion technique and flow stress versus true strain in different solid fraction is compared. It is well accepted that the flow stress s of alloys in their semi-solid state obeys to a thixotropic behavior, due to agglomeration and dissagglomeration phenomena during forming. The load-displacement curves produced from the tests may show an initial peak, believed to originate from a skeletal structure which rapidly breaks down under shear. Apparent viscosity obtained from this method is compared with other works and the proper power law of pseudo plastic state is introduced.

Oct 1, 2011

By D. C. Van Aken, O. J. Rajtora

A research effort sponsored by the Department of Energy (DOE) and several steel producers, is investigating the benefits of coating steelcasting nozzles with various materials. Coatings were applied to casting simulation nozzles made from industrial tundish nozzles (primarily of magnesia) and industrial submerged entry nozzles (SEN&apos;s) (primarily of alumina-graphite) in order to extend casting time prior to nozzle clogging. Nozzles were coated by air plasma spray (APS) using a 9M series APS system from Sulzer-Metco. The ability of these coatings to provide protection from clogging was evaluated using a steel casting simulation. Substrate-coating compatibility was characterized using optical and SEM microscopy.

Jan 1, 2004

By A. R. Chambers

At the 1924 Annual Meeting of the Institute, held in Toronto, the writer presented some notes on the occurrence of salt at Malagash, Nova Scotia, together with a few remarks on the uses of salt. The development of these salt mines has attracted considerable attention to the district, and it may be of interest at this time to call attention to some of the newer uses of salt, and to give a brief account of the genesis of the Maritime salines, As it is not proposed to treat the subject in technical detail, and the paper is written in a lighter vein than is usual in contributions to your Transactions, you will please overlook any variations from a strictly technical method of presentation. The world&apos;s supply of salt is obtained in three principal ways: (1) By flooding shallow areas, or pans, with sea water, allowing the water to evaporate naturally by the heat of the sun&apos;s rays, and collecting the residue of solid salt. This method is employed, for example, at Turks Island, B.W.I. (2) By mining the rock salt in its natural state, and preparing it for market by a grinding process. This is the method adopted at Malagash, which is the only place in Canada where salt is actually mined. (3) By drilling a hole into an underground salt deposit, forcing fresh water clown the hole, and, after it has become saturated with salt, pumping the brine to the surface and recovering the salt by evaporation. This is the method pursued by the Canadian Salt Company, the Dominion Salt Company, and other producers in Ontario.

Jan 1, 1929

By M. Kaya, A. R. Laplante

"Since the beginning of eighties the use of flotation columns has surged in Canada and abroad; the metallurgical superiority of columns over mechanical cells is in great part due to froth washing, which ensures higher gangue rejection and selectivity. Can wash water, which has proven so beneficial, be used in mechanical cells? Although froth washing technology was widely implemented in Soviet plants for bi tuminuous coal, and alusite, powellite, scheelite, molybdenite, etc. more than 25 years, it has been neglected in the western world. Published data suggest 10 to 15~ increases in grade and/or recovery with wash water in mechanical cells (Klassen and Mokrousov, 1963). There are at least three wash water plant applications in Zaire, Chile, and Canada, but little, if any, published information is available. This research work, which is the first extensive fundamental study related to froth washing in mechanical cells, attempts to answer the questions of how, how much, and where should wash water be added.This project was undertaken in three stages:1. Bench-scale laboratory tests with a 6.5 L Denver cell at McGill using a silica flour and a slime reject from Niobec (St.Honor6).2. Pilot-plant scale tests with a 65 L Denver cell at McGill using the silica flour and a complex Cu-Ni sulphide ore from the Strathcona mill of Falconbridge.3. Plant-scale tests with a bank of 2800 L Denver cells at Falconbridge Ltd. for complex Cu-Ni sulphide ore and Eastmaque Gold Mines Ltd. for Au tailing reclaimation."

Jan 1, 1989

TIPS FOR SUCCESSFUL WASTE MANAGEMENT ? WASTE MANAGEMENT PLANS ? Define the question to be asked in waste characterization studies ? Calibrate assessments and designs with field conditions ? Ensure consistent with short, medium and long-term mine plans ? Design robust plans - goalposts and expectations will change ? Fully assess and integrate costs into economic models ? Integrate waste specialists into the feasibility and design teams ? Keep it simple and when you can?t, communicate it in simple terms ? PLAN EXECUTION ? Integrate the waste management plan into daily mine operations ? Identify the critical KPI?s , track them and set clear action triggers ? Know the difference between knowledge and data ?make sure you retain knowledge and document the important Maintain management, engineering and operational focus through the mine life

May 1, 2010

By E. H. Kranck

Introduction Baffin Island is still too in-accessible to be of interest to the mining industry. However, twenty years ago few people dreamed of mining iron ?ore in Labrador. A journey by air to the most remote places in the Arctic is today no more remarkable than a trip to Europe, and the technical difficulties of mining minerals of high value are not insurmountable. Some ?observations concerning the geology and mineral possibilities of Baffin Island, the largest of the Arctic islands, may therefore interest the members of the Institute, in spite of problematic practical value of the subject. The following short account is mainly based on observations made during the Baird Expedition of the Arctic Institute of North America last summer 1950), and on information available from earlier expeditions. Early Work Baffin Island was one of the first parts of Canada to attract prospectors. Frobisher sent a shipload of rocks, which he believed contained precious metals, from Baffin Island to England. This attempt, however, was a failure and no further serious prospecting work has, so far as I know, been done. During the past few years geological mapping has been carried out by the Geological Survey of Canada (Fortier. Davison, 1949-1950) in the southern parts ?of the island, along the coast of Hudson strait. In 1942, Weeks mapped the coast from Pangnirtung to the head of Cumberland fiord, and Netteling river up to Netteling lake. In the northern parts of the island, only scattered observations have been made ?by Bell, Watkins, Baird, and others.

Jan 1, 1951

By Philip Peck

Mine closure issues ?Narrow issues: ?Environmental focus; ?Broad issues: ?Social issues and sustainability; ?Continued importance of mining; ?Historical legacies from closed mines; ?Barriers to development; ?Migration [ir]reversibility Dealing with closure issues ?A matter of choice ?Option 1: Engagein solving closure problems as best possible; ?Option 2: Exit, leaving the playing field to firms not interested in solving problems ?Option 3: Delay, till better time to enter or until early entry [by others] fails and pick property up cheap [?].

May 1, 2006

By K. E. Waters, C. Marion, T. Grammatikopoulos, A. Jordens

"The Nechalacho deposit, located in the Northwest Territories, Canada, is a heavy rare earth element (REE) deposit. The main REE-bearing minerals in the deposit are zircon, allanite, bastnäsite, synchysite, columbite (Fe) and fergusonite. Previous work investigated the use of gravity and magnetic separation in the processing of this ore and showed that coarse particles following grinding were enriched in zircon, suggesting the potential for selective comminution. The current work investigates the possibility to selectively comminute gangue minerals and concentrate REE-bearing zircon into coarser size fractions. The ore was ground wet in a laboratory rod mill for various lengths of time (0, 10, 20, 30, and 40 min). The resultant products were analyzed using ICP-MS, to determine the distribution of zirconium and REEs in the different size fractions produced after grinding, and QEMSCAN, to identify mineral phases, mineral liberation and the distribution of minerals. Optimum grind sizes for the upgrading of zircon due to selective comminution were then proposed, and dense medium separation was investigated as a means to further concentrate zircon.It is important to note that this process is not representative of the currently selected process design or recovery for the Nechalacho deposit. Any application of this process to this deposit would require optimization in order to ensure appropriate grade and recovery targets are met.INTRODUCTIONThe rare earth elements (REEs) are the fifteen elements in the lanthanide series of the Periodic Table, as well as yttrium (scandium is excluded in this work). Traditionally, REEs are categorized into two groups: the cerium sub-group of “light” rare earth elements (LREEs); and the yttrium sub-group of “heavy” rare earth elements (HREEs) (Golev et al., 2014). The LREEs comprise the first six lanthanides (lanthanum through samarium) and the HREEs comprise the remaining nine lanthanide elements (europium through lutetium) coupled with yttrium (Golev et al., 2014). HREEs are much less abundant in the earth’s crust and on average are more expensive than LREEs (Seredin, 2010). Of the fifteen REEs, the production of neodymium, europium, terbium, dysprosium and yttrium has been determined to be most critical due to their scarcity, high demand and criticality in many high-technology and clean energy applications, such as in illuminated screens for electronic devices and permanent magnets in wind turbines (Seredin, 2010; U.S. Department of Energy, 2011). These five elements are classified as critical rare earth elements (CREEs) (U.S. Department of Energy, 2011)."

Jan 1, 2016

By A. Michalkow

DELN ITE Mines Limited is located in Deloro township, on the west end of the south break of the Porcupine Camp. Mining operations are currently being carried out on the downward extension of a system of quartz veins in an andesite zone. This zone has been followed from surface to the present bottom level of 5,250 feet. The changing mineralogy of the vein system has involved an increase in tourmaline content from the surface downwards, so that the veins at the lower levels are composed of dark brown quartz-tourmaline. The drilling problem presented by these extremely hard veins was partially alleviated by the development and adoption of a one-inch drill bit. All blast-hole drilling is now done with the one-inch bit, without any difference in hole spacing.

Jan 1, 1962