Search Documents

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By H. K. Fredrickson

"Midwest Joint Venture (MJV) owns a high-grade uranium deposit in northern Saskatchewan. The deposit is located too deep below surface to be mined economically by open pit methods, and as a consequence, present plans are that it will be mined by underground methods. High-grade uranium ore of the type at MJV, encased in weak, highly altered ground and with radon-rich water inflows, has not before been mined by underground methods.The test mining phase of the project, completed in 1989, had three objectives: 1. to evaluate radiation protection requirements associated with the handling of large quantities of radon-rich water and mining highgrade uranium ore in an underground environment; 2. to investigate the quantity and quality of water inflows into the mine; and 3. to investigate ground conditions in and around the ore zone as an aid in determining the production mining method to be used.With information gained from the test mining project, a mining method for the production mine has been devised. Level plans have been drawn up, ventilation system designed, pumping arrangements made and methods of ore handling considered. All this is to be done in a manner that will be safe for those doing the work underground. Some of the mining methods planned are felt to be unique in that they are designed to cope with mining problems not known to have been encountered before. New problems underground have required new methods to handle them. Remote drilling, blasting, mucking and backfilling form the basis of the planned mining method."

Jan 1, 1992

By Godfrey W. McDonald, Dennis E. Fredrickson

"Commercial coal mining has been recorded in Nova Scotia since 1863 and during this period an estimated 60,000,000 short tons of mine discard containing 10 1030% coal has been accumulated, Approximately 70% of these dumps are in the Cape Breton region and most are owned by the Cape Breton Development Corporation (CBDC), formerly DEVCO.The explosion of oil produced energy costs which created an increase in thermal coal demand as well as the desire to rehabilitate abandoned mine dumps encouraged coal reclamation. CBDC was receptive to a proposal from the Selminco Joint Venture and encouraged the building of the Princess Recovery Plant (1980) and The Summit Plant (1982).The mine dump contains scrap, waste rocks, coal and substantial quantities of fine shale. The scrap and oversize are removed and the remaining material slurried with water to a density of 1.45. The slurry is cycloned to separate the saleable thermal coal from the rejects which are returned to designated areas of the dump for contouring and revegetation.BackgroundThe recorded coal production in Nova Scotia from 1863 to 1980 was 390,000,000 short tons. This extraction was associated with an estimated 60,000,000 short tons of discarded material. This mining discard and coal washing plant reject are located in numerous, varying sized dumps throughout the mining areas. Approximately 70% of these dumps are in the Sydney coal field region of Nova Scotia. The coal content of these dumps varies from 10 to 30% coal with an average of 18%.Energy CostsThe explosion o f energy costs in the mid-1970s greatly increased the sale price of thermal coal which made recovery of coal from some of the dumps economical. The environmental benefit of these operations will be the rehabilitation of the dumps upon cessation of the coal reclamation operation."

Jan 1, 1983

By T. T. Chen, J. E. Dutrizac, G. Poirier

In the Waelz kiln process, EAF dust is converted to an Fe-rich slag, a (Zn, Fe)-rich dust that is recycled to the kiln and the Zn-rich Waelz oxide which is subsequently up-graded for the recovery of zinc. To clarify the reactions occurring, the Waelz kiln products from a European Waelz plant were characterized mineralogically to determine the mineral species present, their micro-textures and the metal carriers. The EAF dust contains 27 % Zn, and consists mainly of ZnFe2O4 and ZnO, together with minor to trace amounts of NaCl, PbCl2, KCl, CaO, Ca2Fe2O5, Fe203, FRO, Pb oxide and various Ca-Fe-Al-Mn silicates. The KCI and NaCI sometimes agglomerate the other particles. The slag consists of nodules which often exhibit colloform structures. The slag contains of variable amounts of Fe, FeO(OH), FeO, gypsum, Ca(OH)2, Ca2SiO4 and various Ca-Fe¬Al-Mg-Mn silicates as well as minor to trace amounts of ZnFe2O4, Cr-Fe oxide, Mn-Fe oxide and other species. The Waelz oxide contains 57-61 % Zn, and consists predominantly of ZnO, with minor to trace amounts of KCI NaCl, Pb(OH)Cl, Pb20(SO4), Pb chloride, ZnSO4, ZnFe2O4, Ca2SiO4, Ca2Fe2O5, Ca-Fe silicate and NaZn4(SO4)(OH)6Cl.6H2O. The KCI agglomerates the other particles in the Waelz oxide. The recycled dust appears to be a mixture of EAF dust and Waelz oxide, but it contains relatively more coarser-grained metallic Pb and Pb oxide particles.

Jan 1, 2004

By Greg Yuriy

This paper discusses research carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in the field of discrete-event simulation of mine equipment systems and reliability assessment of these machinery using genetic algorithms. The AutoMod simulation package, from Brooks-PRI Automation Inc., is used in this research. It is a 3-D discrete-event simulation/animation software tool for creating realistic depictions of manufacturing and materials handling systems. Discrete-event simulation involves modeling of real-life systems based on variables and events which occur or change at distinct points in time. In our case, a two level, multi-drift sublevel stoping model was created in AutoMod for the simulation of the equipment fleet employed in the development cycle (drilling, explosives loading, blasting, materials hauling, ground support) of a typical underground mine in the nickel mining region of Sudbury in Ontario, Canada. The equipment primarily considered in the simulation is Load-Haul-Dump (LHD) vehicles (scooptrams), drills, explosives-loaders and roof bolters. The purpose of the simulation study is to assess the impact of equipment failures to mine?s production throughput. In more detail, using Mean Time Between Failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity. This paper will indicate the significance of equipment failures to a mine?s production and suggest a methodology based on the combination of discrete-event simulation and a predictive reliability assessment model using genetic algorithms for the study and analysis of mine equipment systems.

May 1, 2003

By L. A. Clark, G. H. R. Burrill

"Most unconformity-type uranium deposits in Saskatchewan occur within a few tens of metres above and/or below the basal unconformity of the 1,45-b.y. Athabasca Sandstone. Graphitic basement rocks coincident with post-Athabasca faulting or brecciation at or near the unconformity are important in localizing uranium deposits which form as tabular, ribbon-like bodies with grades averaging over 2 per cent uranium and containing up to 50,000 tonnes UJOs. Some of these deposits have similar contents of nickel and arsenic.In the genetic model proposed to explain these deposits, traces of uranium were leached from the sandstone and weathered basement rocks by oxidized formation waters sweeping through the sandstone and along brecciated faults. Over basement meta-petites, a thick clay regolith adsorbed uranium from the solution. Thus fixed, the uranium was reduced through an indirect reaction with graphite, possibly involving methane. The clay mineral surfaces were thus continuously cleared to allow further adsorption. Basement faults localized along weak graphitic units were re-activated, offsetting the sandstone formation, probably at the time of an early uranium deposition about 1.2 b.y. ago, and served as vents for spent ore solutions. Fluid convection was induced by topographic relief and/or crustal heating from radioactive decay in basement plutons or mantled Archean domes with uranium and/or thorium contents a few ppm above those of adjacent rocks. Heat from radioactive decay within the incipient uranium deposit would develop in about a million years. The self-generating convection cell would continue uranium deposition until all permeability was plugged by minerals. In some instances, convection was re-initiated after subsequent faulting and brecciation. While some deposits were further enriched, heavy flows of oxidized fluids re-dissolved and partially depleted other uranium deposits.The East Alligator Rivers uranium deposits in Northern Territory, Australia, occur within Middle Proterozoic quartzchlorite and quartz-muscovite schists overlain by sandstone. Highest grades occur in silicified breccias where carbonate beds were leached out. Mineralization ages are both pre- and post-Kombolgie Sandstone, but, to date, no significant uranium mineralization has been encountered in the sandstone. There are many general similarities with Saskatchewan deposits, but important differences in detail."

Jan 1, 1981

By E. T. W. Bailey

A HISTOR Y of the development and application of instruments, from the simplest U gauge to a modern indicating recording controller, would contain many interesting accounts of difficulties experienced and over-come. Important as is the history of development to any branch of science, this phase will, of necessity, have to be omitted from this paper and remarks confined to the results from the use of instruments in their present form. The steel industry bas, in the past decade, become increasingly instrument minded. More than ever, economy and adherence to doser specifications are demanded, and any tool that will aid in attaining these objectives by intelligent application and use finds a ready acceptance. The open-hearth furnace bas offered a field for instruments which is different from almost any other and one in which even a small percentage saved in operating costs may represent a considerable sum. Nevertheless, this department of the steel industry has been more cautions than most others in accepting the benefits which automatic control bas given on many other types of industrial furnaces, and one is puzzled why open hearths have not more generally benefited by the application of controlling instruments. The furnace operator bas to adjust the same three main valves that control fuel, combustion air, and stack draft as on most other furnaces, with the additional regulation of reversing the furnace. He is just as aware of the importance of proper draft control and correct air volume to burn most economically the applied fuel as any good boiler-plant engineer. What, then, are the special conditions that pertain to the open-hearth furnace?

Jan 1, 1939

By J. F. K. Brown

WHEN I first received the kind invitation extended to me by the Mining Society of Nova Scotia, I read over very carefully the suggested title-"The importance of long-distance planning and budgetting in modern methods of mining, and the advisability of working to some definite plan". I came to the conclusion that I might as well confess my inability to handle properly such a vast and intricate subject within the scope of any one paper. More properly, I think a round-table discussion should be indulged in-a sort' of symposium carried on in similar fashion to the World Power and Coal Conferences- you know, a committee for this, a committee for that, and, finally, a committee to see what the committees are doing. Weil, your Secretary's suggestion is just like that- much too comprehensive for any half-hour's presentation. As a paper, also, it either becomes too general and therefore uninteresting, or i.t descends into detail and describes means and methods to the end desired, which have little attraction because they were designed to meet quite different conditions than those my audience would mentally be considering. Of the two evils facing me, I have chosen the one that sticks to the generalities. Your Secretary's query almost automatically divides itself into two distinct phases: First, the importance, and second, the advisability, of planning. Let us dwell for the moment on the second, because, if we can prove advisability, that leads to desirability and, finally, to doing. Proving is the difficult part of the little problem. Here was something I, personally and as a mining engineer, had been battling for all my corporate life without being able to prove it to anybody. Then I saw the way out of that. I perceived I could put that little question of advisability on another basis altogether-:put it in the class of "coming- some day- soon" whether you or l or anybody else liked it or not; call it, if you please, mandatory, certain, necessary, enforceable planning. All of which means that the problem of advisability has rather suddenly become the very practical one of "how to do it". Why?

Jan 1, 1937

By Kurt D. Mitchell

"This paper discusses general application for A C variable frequency drives in the mining industry. A review of induction motors characteristics, adjustable frequency controller fundamentals, and three commonly used controllers is presented. General application guidelines for the three different types of controllers; variable voltage input , current source input and pulse width modulated are then reviewed in detail, and an example of the economic benefit of this technology is discussed. IntroductionSoon after static DC variable speed drives were well established in industry, a need for static AC variable speed drives was seen. The first technical papers describing possible systems appeared in the mid-1960s, with commercially available units arriving in the early 1970s. Without exception, static AC drives are substantially more complex than their DC counterparts, but they have some very desirable properties. As compared to DC motors, AC motors are less costly, physically smaller, more reliable, require less maintenance , easily sealed, have good load regulation, are able to run at higher operating voltages, and have little danger of over-speed runaway . These properties are particularly desirable in explosion-proof, submersible or difficult accessibility applications.Variable speed AC drives are now a proven technology. available in packages from Sub-horsepower to hundreds of horsepower, from 115VAC to 4160 VAC. This paper covers the principles of operation of three common types of controllers, application criteria, motor consideration and finally an example of how an AC variable speed drive can pay for itself in terms of energy savings."

Jan 1, 1986

By H. Clare Horwood

"Three types of structures, the main shear zone, the north shear zone, and a series of hanging-wall fractures, contain all the orebodies so far discovered at the McKenzie Red Lake mine. Lenses and veins of quartz in these zones and fractures are the sources of the ore. The ore-bearing structures are unusual in that they are in a complex intrusive mass known as the McKenzie-Gold Eagle stock. They are believed to have been produced by compressive stresses from the south andsouthwest.The mine is on the northeast side of McKenzie island, in Dome township in the central part of the Red Lake area. The original discovery, the main shear zone, was made in 1928, about 3 years after the property was staked, by M. L. Bouzan who was in charge of prospecting and development work on the property. Subsequent diamond drilling and underground exploration led to the installation of a mill, which came into production early in 1935. The hanging-wall fractures were found branching out from the main shear zone during development work on the 350-foot level. The north shear zone was discovered in 1940.From 1935 when the mill began operation until the end of 1946 total production from the mine was approximately 269,349 oz. gold and 69,317 oz. silver, having a value of $9,679,739, recovered from 823,527 tons of ore.GENERAL GEOLOGYThe McKenzie-Gold Eagle stock has a total length of approximately 1 ½ miles and a width of about ½ mile. It was intruded into a complex synclinal fold in Timiskaming sediments. The sediments, which have been cut in only one place in the underground workings, are principally wellbedded greywackes. The stock is composed of large masses of diorite and granodiorite, a small mass of hornblende pyroxenite, and basic dykes of two ages. The diorite occurs as irregular masses in large measure surrounded by the granodiorite that it intrudes. It contains tabular crystals of andesine, having a maximum length of3/4 inch. The hornblende pyroxenite is an elongated lens or dyke in the diorite. The granodiorite masses occupy about two-thirds of the stock. Along its eastern side the main mass tends to become darker and more dioritic toward the diorite contact.Basic dykes of pre-vein and post-vein age are the youngest intrusive rocks at the mine."

Jan 1, 1954

By M. Fiset, D. Belley

"In a country with a cold climate like Canada, the cost of replacing worn parts of snowplow equipment such as blades, is enormous. A great number of these blades, with different mechanical properties, are available, but few studies have been made to facilitate their selection according to the optimum ratio of wear resistance to cost. To attain this objective, laboratory tests have been developed to correlate test results with those obtained from various road service conditions. The test materials, 1080steel in different states, 1090steel and D2 tool steel were chosen to cover a large range of hardness as well as different microstructures. Comparison of the wear resistance of the test materials relative to a standard revealed, in general, a good correlation between the results of laboratory cement wheel tests and those from the road tests. Scanning electron microscope wear scars of laboratory and road test specimens were compared to determine if similar removal material mechanisms were active. IntroductionThe correlation between wear tests in service and those performed with the aid of laboratory equipment is of considerable interest. As a matter of fact, when correlation exists, it allows one to evaluate the performance of a material more easily and at a lesser cost.Several authors have been interested in simulating various wear circumstances, especially abrasive wear. In particular, the simulation of wear on implements working the soil, has been tried by several researchers. The test using the rubber wheel seems to be the one giving the best correlation if the soil is rather sandy and its moisture content is low.However, little work has been done concerning wear on the plates, skids and blades attached to trucks used for levelling and snowplowing; such equipment being used to keep roads clear in northern countries. Now each year, companies introduce new steels by claiming that the y are superior in performance to their predecessor s and invariably they demand a higher cost. The study presented here was undertaken with the goal of making a more judicious choice of these steels by simulating their behaviour in the laboratory. Moreover, the examination of abraded surfaces in situ and in the laboratory have also allowed us to compare the respective wear mechanisms."

Jan 1, 1988

By J. F. Harkom

Introduction The importance of the preservative treatment of mine timbers need scarcely be stressed here. Increasing the life of mine timbers will reduce one of the major costs of mining and also conserve the available timber supply which lies within easy access of the mines. When treated, several species of timber may be used which otherwise could not be considered, owing to their short life. Another feature which should appeal to the mining industry is that wood preservatives are a mine product, and the benefit to be derived from the increased consumption of wood preservatives due to the example set by mine owners is not inconsiderable. Mine timbers may be divided into three classes when considering preservative treatments. (1) Timber obviously not profitable to treat owing to long natural life or short period of time in service. (2) Timber that obviously should receive protection from decay. (3) Timber installed in locations where the length of service required will depend on future developments, so that preservative treatments might or might not prove to be a profitable investment.

Jan 1, 1930

By Joseph Bradley

THROUGHOUT this article, minerals used in the paint industry are designated 'pigments'. They may be classified in two groups: (1) Pigments which are used in the state in which they occur in nature, requiring only mechanical preparation. (2) Pigments which require heating or chemical treatment before use, in order to obtain from them a product of the desired quality or shade of colour. They may be further classified according to colour, as follows: White Pigments .-These include calcium carbonate (chalk, marble), gypsum and alabaster, kaolin-or china-clay, and magnesia. However, the white pigments most extensively used are compounds prepared chemically from minerals containing lead, zinc, titanium, and antimony. The white pigments are of particular importance because, not only are they used by themselves, but they also serve as adjuncts to other colours for the production of special shades. Yellow Pigments.-These are mainly naturally occurring ferric hydroxides, as limonite and bog iron ore, or similar. compounds prepared artificially. Brown Pigments .-Pigments of this group are distinguished for their beauty and depth of colour, and many of them are used in the finest of paintings. Familiar names are sienna, umber, and Vandyke brown. They are for the most part ferric hydroxides, containing varying amounts of water; but the group also includes a manganese brown, which consists chiefly of a mixture of oxide and hydroxide of manganese. Red Pigments.-Chief among this group is ferric oxide, known under various trade-names, such as Canadian red, Persian red, etc., and also the much prized and somewhat rare vermilion. The pigment used is either naturally occurring hematite, de-hydrated limonite, or artificially produced red ferric oxide.

Jan 1, 1937

By Bonnie Cooper

3D printing by fused deposition can be used on lunar soil. The soil can be precisely size-separated to make the 3D printing process work efficiently. Using a MASER instead of a LASER would allow us to use the finest fraction of lunar soil, AS-IS, to manufacture things on the Moon.

May 1, 2013

Owner?s Team and EPCM ?Teams rolesmay vary to suit the skills available, however the tasksremain the same ?Ensure adequate level of capability in the team ?Large owner?s teams vssmall owner?s teams ?size of owner?s teams can reflect not only the individual level of capability but also the type ofrelationship with the EPCM contractor ?Wholly owned projects vsjoint ventures projects ?Both cases require clear accountabilities and authorities ?Project sponsor should be a senior executive with commercial andtechnical accountability of project outcome ?Project leader should be experienced and have solid leadership capabilities ?Attention should be paid to balancing personality types in an owner?s team

May 1, 2010

By Garth D. Kirkham, James P. Siddorn, Hendri Falck

"Abstract - As an integral part of the Geological Survey of Canada’s EXTECH III Project, a threedimensional computer model has been created of the Con and Giant gold mines in the Yellowknife Greenstone Belt. The Yellowknife Mining Camp has produced a great deal of gold (over 15 million ounces, or 400 000 kg) in the past sixty years and the prevailing assumption is that the mines are at the end of their lives. However, the potential for discovering additional resources using new ideas and technology, and maximizing use of existing data, offers an opportunity to sustain the old mining operations and maintain their contribution to the community.The objectives of this study included the compilation and creation of a three-dimensional Geographic Information System model (combining 3D subsurface data with surface information) to provide a framework for concurrent structural and alteration studies, and to encourage new exploration in the area. A secondary objective was to retain the data in digital format as a historical reference for future remediation efforts, and to document a portion of Canada’s rich mining history.The end result is a database and set of models that have been instrumental in facilitating further exploration in the area, as well as in developing targets for future exploration and mining activities. In addition, the EXTECH III 3D GIS model has made a valuable contribution toward the understanding of the arsenic remediation issues at the Giant mine, and has served as a tool in support of a variety of highly technical engineering studies and for communicating information and problems to the layman and community as a whole."

Jan 1, 2003

By A Sadough Vanini

In this paper large deformation of smart functionally graded beams with initial imperfection and under thermal loadings is considered. Smart beam consist of two types of layers. One layer is made from functionally graded materials and a layer or a set of layers from active materials that usually is made from piezoelectric materials that are bounded on the surfaces of beam. An active controller is used for controlling the deformation and stress in functionally graded layer of beam. A simple Euler- Bernoulli beam theory is used for analyzing of beam. In functionally graded layer the material property vary continuously through the thickness direction and power law model is used for the variation of elastic modulus, heat expansion and heat conduction coefficients. Poisson ratio is assumed to be constant in functionally graded layer. The effects of varying the power law constants and the Gain of controller is considered here. The results are reduced and compared with smart functionally graded beam without initial imperfections.

Oct 1, 2011

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By R. C. Reed, A. Akhtar

Oxidation of the third generation cast single crystal, nickel-base superalloy CMSX-10 is examined using isothermal tests at 900°C and 1000°C for times ranging from 20 hours to 100 hours. X-ray diffraction, scanning electron microscopy and energy dispersive secondary X-ray analysis were used to characterize the microstructure. It was found that the external scale formed at 1000°C is made up of (Ni,Co)O and the spinel NiCo2O4. The (? + ? ') microstructure of the superalloy transforms into the intermetallic (3 phase prior to the onset of internal oxidation. Internal oxidation results in the formation of (Ni,Co)Ta2O6 and (Ni,Co)WO4. No evidence was found for the formation of alumina (Al203), and the spinels NiCr2O4 and NiAl2O4 in this third generation superalloy. Results of the laboratory investigation are compared with those of an aero-engine turbine blade removed from service and examined earlier.

Jan 1, 2004

SOME months ago a Committee on Deep-level Mining was appointed [by the Government of the Union of South Africa] to consider the possibility of gold mining being carried on at a depth below 8,500 feet. The Committee consisted of Sir Robert Kotze (Chairman) , Mr. H. S. H. Donald (Government Mining Engineer), and Mr. H. R. Hill. The Committee has now made a report which was tabled in the House of Assembly on March 1st. The Committee reported that the tonnage of ore locked up in the deep level areas of the Central Witwatersrand is enormous, and in the 30 miles between Roodepoort and the East Rand Proprietory Mines has a value of about £200,000,000. The Committee says that, with good ventilation, the present system of wet mining, possibly with some modification and with the aid of refrigeration, may be carried to 10,000 feet, but that greater depths will require the adoption of dry mining. "A vigorous campaign of practical experiment into the possibility of dry mining should be initiated, and the Committee recommends to the Government the appointment of a committee of experts, consisting of representatives of the mining industry, the Mines Department, and the medical profession, with the Government Mining Engineer as chairman. The Committee suggests the provision of £30,000 for the first year for the investigations and experiments contemplated, which could best be carried out by an organization which might be styled 'The Rand Mining Research Institute' and constituted somewhat on the Jines of the South African Institute for Medical Research" . The Committee suggests that this committee of experts should arrange for experiments to be made with dry mining in one of the deepest mines, and investigate ventilation, refrigeration, support of workings, and the physiological problems connected with mining. "We emphasize the necessity of treating this whole question as one of importance and urgency. The investigations should be prosecuted with the utmost vigour and should not be delayed at any time for want of funds or for any other reason. If they are not done thoroughly and quickly, the whole scheme might just as well be left severely alone.

Jan 1, 1945