Search Documents

By Frank Yu, Bob Fukuhara

"The Stillwater mine is a 3,000 tons/day platinum/palladium underground mine and flotation concentrator located in the Beartooth mountain range in south-central Montana. The site elevation is 5,000 feet above sea level providing a climate with pleasant summers and cold winters. The winters are particularly characterized by very strong winds.The mining methods at Stillwater had been variations of overhand cut-and-fill and some blast-hole stoping. Until construction of the paste back-fill plant, mine back-filling was being practiced using classified hydraulic sand-fill methods. Where higher strengths were necessary, cement was added to the hydraulic fill, however, excessive quantities were necessary due to significant losses with the water drainage from the comparatively low-density fill. There was a need for higher strength back-fill with reduced cement content to augment the hydraulic-fill process.In early 1998, Stillwater Mining Co. commissioned AGRA Simons (then H.A. Simons) in a joint venture with The Industrial Company, TIC, to design and construct a treatment facility to re-process the mill flotation tailing, incorporating the following process alternatives:Produce 100 tph of low strength paste with unconfined compressive strength of 25 to 50 psi,Produce 100 tph of high strength paste with unconfined compressive strength of 100 to 125 psi,Direct all of the excess mill tailing to the sand-fill plant,While no paste is being produced, pump all of the mill tailing to the sand-fill plant,While no paste is being produced and the sand-fill silos are full, direct the mill tailing to the tailing pond.The paste backfill plant was therefore to be designed to produce the two different types of backfill paste as well as have the function of being the distribution center for the mill process tailing .Moderate to high slump pastes would be required because of the comparatively long horizontal transport distances, up to 8,000 feet, and the requirement for a low angle of repose to fill the stope evenly without numerous discharge points."

Jan 1, 2000

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By Jan E. Nesset, Colin Hardie, Peter Radziszewski, Donald P. Leroux

"The successful introduction of new high intensity stirred milling technologies (e.g. IsaMill, SMDetritor) to the mining industry in recent years prompted Noranda-Falconbridge to initiate a study comparing these technologies to the conventional technologies of ball milling and existing vertical stirred mills (e.g. VertiMill). The study was unique in that it utilized the same material (Brunswick Mine zinc cleaner regrind mill feed), the same sizing instrument (a Malvern laser difractometer) and sampling protocol, and media size and type (for the high intensity stirred mills). The paper compares the net energy efficiency (kWh/t) of the various technologies, their power intensity (kW/m3) and product size distribution spread (P80/P20). A key finding is that media size is critical to achieving optimal performance. As part of the performance comparison, an analysis of the four methods of power measurement was made (Prony brake, shaft torque, grinding chamber reaction torque, “no-load” correction) and followed-up with an experimental test procedure using three of these methods. The findings include divergent results for power measurements and some explanations based on the observations are proposed. The direct shaft torque and Prony brake calibration methods are shown to be the methods most suitable for stirred mills.INTRODUCTIONThe motivation for the investigation reported here was the lack of a suitable comparison within the available literature of relative grinding efficiency for the emerging crop of new industrial fine grinding technologies. Such comparisons are potentially fraught with inconsistency, from ore samples and grinding media used, to testing methodology, to size measurement techniques, to the power measurements themselves. The collaboration of the industrial suppliers (at the time MIM Technologies and Svedala, now Xstrada Technologies and Metso Minerals) and McGill University (P. Radsiszewski) were sought in order to ensure as valid a comparison as possible. The work was performed between October 2000 and November 2002, led by the mineral processing group at the Noranda Technology Centre (NTC) in Pointe-Claire, Quebec. The paper is presented in two sections; Part A considers the different power measurement methods and a comparison of the results for the SMDetritor (SMD) technology, while Part B reviews the grinding performance of the 5 technologies investigated using the selected performance criteria."

Jan 1, 2006

By I. P. Barbosa, P. S. M. Soares, I. O. C. Masson

"Permanent magnets have been applied extensively to several electronic products such as printers, TV sets, microphones, microcomputers and headphones, presently manufactured in large scale by industrial economies. Sm-Co alloys represent about 20% of the world market for permanent magnets and their industrial processors generate 20-30% of magnetic scraps which can be recycled. This paper discusses a process route to recycle SmCo5 using acid treatment, solvent extraction of Sm and electrowinning of Co. The results confirm the feasibility of the alternative proposed. Basic operational variables are suggested as guidelines to design a plant for recycling magnetic scraps.The use of hydrometallurgical processes to recycle scraps from the industry of permanent magnets has been suggested in some recent papers related to recycling of metallic alloys [ 1 ]. These research efforts might be understood as a worldwide tendency towards the development of self sustainable metallurgical processes which mean the reduction of environmental impacts.CETEM -Center for Mineral Technology leads in Brazil several research programs concerning recycling and treatment of industrial residues. The work on samarium purification and concentration by solvent extraction, producing also a solution of cobalt sulfate as partially reported here is one of these programs. Previous results related to the sulfuric acid digestion of SmCo5 are presented somewhere else [2]"

Jan 1, 1997

By Chen Xia, G. Deschenes, Wan-Tai Yen

"Ammonium thiosulphate is a potential replacement for the cyanide in gold leaching. However, the high reagent consumption hinders its practical applications. In order to reduce the thiosulphate consumption, chemical additives were used. The gold leaching tests were conducted on a sulphide copper-bearing gold ore with 0.3M thiosulphate, 0.03M copper sulphate and 3M ammonium hydroxide solution at 44% solids and pH 10.2. Sulphate, sulphite, amino acid and chelating agents were initially used as additives. It was found that chelating agents (EDTA and NTA) could reduce the thiosulphate consumption from 30 kg/t to 17.8 kg/t with some increase of gold extraction. The improvement from other additives was not significant. Other approaches were also attempted to reduce thiosulphate consumption with some success. The thiosulphate consumption could be reduced to about 17 kg/t by reducing copper sulphate concentration fiom 0.03M to 0.0015M; adding 0.04M of EDTA; replacing copper sulphate with 0.001M of nickel sulphate. The increase of pulp density fkom 44% to 60% solids could reduce the thiosulphate consumption to 17 kg/t as well. Limiting the dissolved oxygen content by sparging nitrogen reduced the thiosulphate consumption further to 10 kg/t. It could be concluded that the regulations of copper and oxygen supply in the lixiviant were the keys to reduce the reagent consumption.INTRODUCTIONCyanidation, as the predominant gold leaching method, has been used in mining industry for more than a century. The low reagent requirement and the high performance are the reasons for its great success. However, cyanidation cannot deal with ores containing large amount of copper, nickel, arsenic and zinc minerals. This type of ore may consume more reagents and result in a poor gold extraction. On the other hand, the carbonaceous materials may preg-rob the gold from pregnant solution and make cyanidation a problem leaching method. Further more, the high toxicity of cyanide represents another challenge to modern gold mines. In the beginning of the year 2000, an environmental disaster caused by an accidental spill in Yugoslavia was broadcasted world-widely (Gurevitch 2000). Gold mine operators are facing higher social pressures and increasing costs on environmental protections. The usage of cyanide in mining industry has been banned in some countries and locations such as Czech Republic, Japan, Turkey, California, Colorado, Wisconsin and Montana States. Thus, a non-cyanide lixiviant is required."

Jan 1, 2002

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

By Marcel Vallée

Frequently, costs overruns and defaults in mining project performance result in serious problems and headaches for all project participants and impact on corporate objectives, profits and image and, occasionally, lead to project failure. As mining professional s, we should be very concerned that, in a recent World Bank paper (Weber-Fahr, 2001), geological and technical risks were considered the most important ones facing mining projects. Whenever we manage to reduce or minimize these risks, we are in better position to overcome the environment-, market-, finance- and community-related ones. The causes of this situation seem rather systemic, as a fairly long list of industry problems with new pro jects has been described in industry papers in pas t and recent years. A brief review of industry problems with mining projects will be given first, followed by a review of the basics of the current Quality Management and Continuous Improvement perspectives that have evolved from earlier quality control and quality assurance systems and policies. Particular particular attention will be given to the work of W. E. Deming. As the system approach is an essential part of such policies, it will be described succinctly. Given that poor communications and interactions among geologists, mineral processors and mining engineers/operators ca n seriously affect project efficiency and profitability, these interrelated processes with in the mining systems will be analyzed and modelled and the impacts of such situations will be described through a number of anonymous case histories and examples. A synthesis of Dr Deming's management system, includ ing his Four teen P oints and System of Profound Knowledge, will be prese nted .

May 1, 2002

By J. D. Bliss, G. J. Orris, W. O. Menzie

"Analysis of gold placer data from gold placers throughout the world suggests that gold grades and volumes cannot be used to distinguish between most types of gold placers. Only the alluvial plain and fan placers are significantly different among the types of gold placers considered. Gold grades and volumes change when working gold placers go from small-volume methods to large-volume methods. The small-volume methods are either of the surface or subsurface (drift mining) type. The odds that a gold placer will be dominantly worked using small volume methods at the surface are about 5:3. Once small volume mining has occurred, the odds against subsequent large-volume mining are about 4:1. If a placer deposit is suitable for large-volume mining, and the amount of gold produced from small-volume mining was reported, an estimate of the remaining gold (log10kg) can be made using the following equation:The relationship shown by this equation suggests that very large gold placers have over half their total gold content in the rich gravels appropriate for small-volume mining. These relationships in conjunction with other data and computer simulation can be used to estimate placer gold resources for an area targeted for mineral resource assessment. IntroductionGold placers have been an important source of gold throughout man's history and may have been one of the first sources-dating back to around 6000 B.C. (Gregory, 1980). From the primitive basket to the modern floating dredge, a variety of methods have been used to work gold placers. Placers are found in a wide spectrum of geologic and climatic settings. They have been classified by using a mixed set of criteria including age (Recent, Tertiary), climate (desert), fluvial position (modern channel, bench, alluvial fan), environment of deposition (eluvial, alluvial, residual, beach), type of transport (stream, wind, glacier), and whether the placer is buried or at the surface (Boyle, 1979; Wells, 1969). Several mining methods have usually been used to extract gold from anyone placer."

Jan 1, 1987

By Rayleen Riske

Why do we look for better reconciliation when times get tough? Why wait? Mine reconciliation should be a priority throughout the good times too. In fact, with good reconciliation, those good times are going to be even better and will help pave the way to success through those preventable bad times. Reconciliation throughout the entire mining value chain requires the capture, validation, and analysis of copious amounts of data. This task can be daunting for a team in a small mine, let alone reconciling across a suite of large mines. This paper will outline the different ways we can reconcile across the value chain, why we should reconcile over differing periods of time and how Snowden?s solution to proving reconciliation can be a simpler, reliable and transparent process. Snowden?s Reconcilor is proving to be a valuable tool on any mining scale, by capturing, validating, sorting and reporting data for timely decision making by the site geologist through to corporate management. By instigating vigorous reconciliation, you are setting your mine up for the future. Not only will you have the means to analyse your current processes and measures, but you will have the opportunity to identify and improve your mine?s performance from the resource model through to the final product.

May 1, 2010

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By P. Trudel, É. Cabot, L. Cabot

"A modular gold processing unit (MGPU) was designed, installed and operated over an eight-month period by RSW-Béroma at the Granada mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up, as well as exploitation results, including productivity and profitability curves, are given for a small-scale mining operation in comparison with larger ones. IntroductionSmall-scale mining (SSM) is a widespread activity in Africa, Mexico, Central America and South America, where numerous small mineral deposits are exploited manually or by semimechanized methods. On the other hand, SSM is almost absent in Canada, where the mining industry traditionally exploits large deposits, using concentration plants with capacities of many thousands of tonnes per day. However, many small gold (and other metallic or industrial mineral) deposits are known in Canada. Their reserves are too small to justify the cost related to the construction of a standard mill and, if they are remote from a custom milling facility, they remain unexploited. With this in mind, RSW-Béroma has developed the modular gold processing unit (MGPU) that allows the profitable exploitation of small mineral deposits. The MGPU is the perfect tool for SSM and its main advantages are a much lower capital cost than a standard mill and its portability, which makes it easy to transport and reinstall on another site, once the exploitation of a small deposit is terminated. The denomination MGPU will be used hereafter in the text as it was primarily designed for gold deposits, although it must be kept in mind that this portable plant can be adapted to other mineral substances."

Jan 1, 2003

By Deon van Tonder, Chuck Edwards

"Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares some of these options on the basis of typical capital and operating costs for both the solvent extraction circuit and downstream uranium processing, and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.INTRODUCTIONIn the 1950s the uranium industry was the first industry to adopt solvent extraction (SX). Since then, the flow sheets have advanced. Notable was the introduction of tertiary amine extractants by General Mills during the late 1950s and 1960s (Mackenzie, 1997; Mackenzie, 2005), which is still today considered ‘state of the art’ technology. Initially solvent extraction was done in combination with ion-exchange, such as in the Eluex flow sheet, followed later by the adoption of direct solvent extraction from pregnant leach solution (PLS). From a strip-precipitation perspective ammonia strip followed by ammonium diuranate precipitation was widely adopted as the norm in the uranium industry. More recently alternative strip systems have been receiving increasing attention due to the environmental, health and safety issues associated with ammonia and the resulting calcined uranium oxide product. This paper explores some of these alternative options in comparison with the ammonia route.It is important to acknowledge that each operation is unique, and therefore the information and philosophy outlined in this paper serve to provide a general guide that can be potentially applied and adapted to any site or project."

Jan 1, 2013

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By A. B. Cron, R. MacPhail, L. Melis, K. Armstong

"Mt. Milligan is a porphyry gold/copper deposit in north-central British Columbia. Diluted and mineable drill-indicated reserves total 449 million tons at an average grade of 0.013 oz gold/ton and 0.19% copper. Large-scale commercial development of the deposit will make Mt. Milligan Canada's third largest gold mine.Metallurgical investigations for the Mt. Milligan project were done in three phases: scoping tests in the first half of 1989; bench-scale work from October 1989 to April 1990; and a pilot plant program in May and June 1990. Various process alternatives for the recovery of gold and copper are described and results are presented. Net smelter return evaluations led to the selection of optimum process conditions for maximizing revenue from gold/copper flotation concentrates.The selected flotation circuit and basic design criteria are described. Forecast average recoveries over the presently-defined 20-year project life are 75.2% for gold and 90.5% for copper in a copper concentrate averaging 17.6% copper and 1.0 oz gold/ton. 1.0 PROJECT LOCATIONThe Mt. Milligan porphyry gold/copper deposit is located in northcentral British Columbia, 150 km north of Prince George, British Columbia. The site is at an elevation of 1,100 m in an area of logged, gently-rolling topography. Nearby communities include MacKenzie and Fort St. James. Climate in the area is moderate and there is direct road access to the property. A location map is presented in Figure 1-1."

Jan 1, 1991

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

By Claude Bazin, François Robichaud

"The control of the operation of semi autogeneous grinding (SAG) mills is mainly achieved through adjustments of feed rate, water addition and speed of rotation. With the introduction of image based sensors it is possible to have on-line measurements of the size distribution of the ore feeding a SAG mill. This information could be used for the development of a control strategy to regulate a SAG mill feed size distribution to a set-point. The control of the size distribution is carried out by adjustment of the speed of the ore extractors underneath the ore stockpile. The potential and difficulty associated with the implementation of such control are assessed using a multivariable statistical analysis of data collected from the operation of the grinding circuit of the Agnico-Eagle Goldex mine in Val d’Or, QC. A control strategy for the ore feed size distribution is assessed using a simulator of the ore stockpile operation.INTRODUCTIONThe popularity of autogeneous (FAG) and semi autogeneous (SAG) grinding mills has been increasing over the last 20 years (Napier Munn et al., 1996). These mills use the ore or a combination of ore and steel balls as the grinding media. Since the ore is used as a media for the size reduction the mill ore feed size distribution impacts the performance of the mill. Several papers were recently published on this subject (Dance et al.,2011; Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011) showing the advantages of preparing the feed size distribution to maximize the circuit throughput or mill efficiency (Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011). With the availability of particle size sensor based on image analysis of the ore on a conveyor (Partanen et al., 2001; Bobo et al. 2004; Edwards et al., 2002; Wei & Craig, 2009) it is possible to control the size distribution of the ore feeding autogeneous or semi autogeneous mills (Partanen et al., 2001).This paper describes a method to control a size distribution index to a set point via the manipulation of the speed of the extractors that withdraw the ore from the stockpile feeding the grinding circuit. The paper consists of 4 sections. The first section describes the considered grinding circuit. A statistical analysis of the collected data on the grinding circuit is presented in the second section. This analysis demonstrates the necessity of using real-time adaptation mechanisms to develop a control strategy for the size distribution of a grinding circuit. The third section describes the method used to simulate the ore stockpile operation and the last section describes the preliminary development and assessment of a control strategy of size distribution of the ore feeding a SAG mill."

Jan 1, 2013

By S. L. Zekovic

This paper analysis the medium and long-term perspectives, framework and considered possibilities of sustainable development of RTB "Bor" (Copper mines in East Serbia) after consolidation in the period of transition. The copper mine was opened in 1903. and today is the best quality copper producer on Balcan. This paper are elaborates the problems of privatization, debt, investment, growth of copper production from own mines (and imported raw), opening of new mines, economical efficiency of production, markets, environmental problems and impacts of the recent industry consolidation. The RTB "Bor" is a serious hot spot in Serbia. Unsustainable trends and processes are identified, as follows: open-pit waste dumps, flotation tailings, mining and processing waste waters, air pollution; no efficiency (excessive) using nonrenewal resource in the copper production; inefficiency in the use of energy, water and other inputs in copper complex; transboundary character of emissions of dust; environmental degradation and quality of wide area and ecologically highly risk, etc. Analysing some trends and planning-developmental perspectives and development strategies of company, it might be assumed that in the forth coming period, in parts of the Serbia, the borders areas of Bulgaria and Romania, there is an anticipated increase of ecological risk.

Jan 1, 2007