Search Documents

By S. C. Cohen, A. F. Mikkelsen

"This paper describes the improvements made to the operation of a liquid phase, 300°C, heat transfer system in the paste plant of an aluminum smelter. These improvements were achieved by replacing the original heat transfer fluid, a synthetic aromatic, with a new technology, petroleum-based product. This new fluid, Calflo HTF, provided better thermal stability, with lower toxicity, and improved plant working conditions.The procedures for fluid selection, changeout and performance monitoring are described along with a summary of control analysis over the last three years."

Jan 1, 1993

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By Curtis Rempel, John Bartlett, Alex Holtzapple

METSIM is a powerful program capable of modelling and simulating every known metallurgical and inorganic chemical process. METSIM is used by companies throughout the world to design, simulate and control operations from mine to tailings and everything in between. At its absolute simplest, METSIM can be used to create a process flowsheet. METSIM modules and built-in unit operations cover mass and energy balances for either steady-state or dynamic simulations of mine, stockpile, heap leach, material handling, comminution, beneficiation, hydrometallurgy, pyrometallurgy, gas and steam handling, and tailings management processes. Data for the material being processed can include mineralogy, particle size analysis, grade by size or multicomponent size analysis, washability data, mechanical, physical and thermodynamic properties. METSIM is written in APL (A Programming Language). Unlike C++, APL is simple and easy to learn, allowing the user to program whatever they can imagine, without first obtaining a degree in computer science. METSIM can also interface with EXCEL and other software through dynamic data exchange (DDE), allowing data to be imported and exported for viewing, analyzing and controlling. METSIM can answer simple or complex metallurgical and process questions allowing the user to predict and engineer without the issues of clumsy and tortuous spreadsheets.

Jan 1, 2014

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By William Petruk, Donald Leroux, Michael Cooper

"Brunswick's primary flotation circuit (CuPb) produces a low grade concentrate containing considerable amounts of undesirable sphalerite and pyrite. To determine the cause of the poor selectivity, a series of Quantitative Mineralogical Analyses (QMA) were performed on several CuPb circuit streams. It was observed that significant fractions of sphalerite and pyrite reporting to the concentrate was liberated, meaning that their depression was not complete. The study highlighted the need for some R&D efforts to be spent in sulphide flotation fundamentals.IntroductionThe viability of many mining projects strongly depends on the performance of their concentrators. More than ever, competitive grade concentrate and high metal recoveries are criteria of paramount economic importance. The selectivity of solid/solid separation processes used in concentrators must be maintained at high levels or continuously improved.Flotation is the solid/solid separation process used by most base metal producers. In spite of its low operating cost, flotation remains a very complex process. To make it selective, precise reagent dosages and electrochemical conditions must be maintained. The difficulty in controlling flotation lies in the numerous heterogeneous reactions that can take place between the different solid, liquid and gaseous phases involved. This complex chemistry makes flotation selectivity difficult to understand and, therefore, to improve from a theoretical point of view.Brunswick Mining and Smelting, near Bathurst N.B., operates a 10500 tpd concentrator which produces four concentrates through five stages of sequential flotation (Figure I). Various reagents are added at key process stages while the ore undergoes different electrochemical conditions. Although the selectivity is important at all stages, the performance of the very first separation, the CuPb circuit, is the most critical. It is here where mineral misplacement to the wrong stream has the greatest economic consequences."

Jan 1, 1996

By Tom Setterfield

Monster Copper Resources ?Junior focused solely on IOCG deposits ?Founded by ex-WMC geoscientists ?Properties in Brazil, Wernecke Breccias (Yukon), Central Mineral Belt and Nova Scotia Nova Scotia ?JV with Wallbridge Mining Company ?Ongoing Story ?Presented as a case study in generation and implementation of IOCG exploration program

Apr 1, 2005

By J. A. Eisele, D. L. Pool

"The Bureau of Mines has developed a particle agglomeration technique to improve the flow of leaching solution through heaps of low-grade gold-silver ores which contain clays. Benchscale experiments and industrial practice have shown that the percolation rate of cyanide leaching solution is greatly enhanced by mixing the ore with Portland cement as a binder, moistening the mixture, mechanically tumbling to form agglomerates, and aging before heap building and leaching. A slight modification ofthe technique allows its application to precious-metal-bearing tailings, which cannot normally be treated by heap leaching because they are too fine. IntroductionMany low-grade gold and silver deposits and tailing materials from former mining operations in the western United States are potential sources for precious metals. These sources are too low grade or too small to support the capital cost of a conventional cyanidation plant but have stimulated the development of lowcost procedures, such as extraction of the precious metals by heap leaching with cyanide. The Bureau of Mines has investigated methods to improve the recovery ofgold and silver by heap leaching these low-grade materials.For heap leaching to be successful, the crushed and stacked ore must have good permeability so that uniform distribution of the cyanide leaching solution through the heaps can be achieved. Some of the most difficult gold and silver ores to treat by heap leaching are those containing excessive amounts of clays, or fines generated during crushing. Excessive amounts of slimes, generally minus 50-micrometre or 270-mesh Tyler sieve size particles, in the heap feed will slow the percolation of the leaching solution, cause channelling, or produce dormant or unleached areas within the heap, resulting in long leaching periods and low extractions. In extreme cases, the clays or slimes can seal the heap and cause the leaching solution to run off the sides of the heap rather than through it."

Jan 1, 1987

By J. L. Bowlby

OWING to the pressure of routine analyses at the laboratory during the past year, work of an investigational nature on water problems has been greatly curtailed. Favourable reports by the boiler inspectors indicate that the operators are giving satisfactory attention to feed-water treatment at the several . power plants. Some of the operators prefer lime and soda, others the phosphate and soda treatment. Springhill is still on the same commercial treatment as they were using last year, and satisfactory results are being obtained. This individual preference for a particular treatment, although it may be different for feed waters of similar nature, indicates that so long as proper conditions of alkalinity and concentration are maintained within the boiler, it is immaterial what chemicals are used in the treatment. This statement refers, of course, to the low-pressure boilers. In high-pressure boilers, a treatment such as lime and soda cannot be satisfactorily employed, on account of the precipitated calcium carbonate unduly increasing the amount of suspended matter. Only one case of impending trouble was reported during the year. That was at Seaboard, shortly after the new unit was placed in operation. Dissolved oxygen, considerably in excess of the permissible 0.030 cubic centimeters per liter, was detected at various points on the feed line. It was suspected that a de-aerating heater was being operated at too low a temperature, and chemical tests, made before and after the necessary adjustments, proved that this was the source of the trouble. While it has been impossible to give mine waters the attention they require, progress can be reported in the work carried out by the Mechanical Department. Past investigation of the action of mine water on various acid-resisting alloys is now bearing fruit, and it can safely be said that repair work on mine pumps has been reduced by nearly one-half.

Jan 1, 1938

By S. Perkins, E. Young, L. Dufour, K. McVey, L. Rolandi

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By Louis Tellier

SIDBEC commenced detailed planning of major capital expenditures to install integrated steelmaking facilities in 1969. Today, less than IO years later, SIDBEC and its subsidiaries have completed major mining, concentrating, pelletizing, direct reduction ? electric furnace steelmaking and continuous casting plants. The total cost of these projects was almost 1 billion dollars. The philosophy behind the project planning and the evolution of management control are explained. These extensive projects were undertaken during a period of exceptional inflation and a disturbed labour climate, but were nevertheless completed with only modest overruns, with good control of timetables and with exceptionally good start-up performance. Project planning, relations with consulting engineers, introduction of new technology, purchasing and field management and cost control are discussed.

Jan 1, 1979

By J. F. Perreault, J. Paraszczak

"The profitability of an underground mine depends to a great extent on the production cost.Random equipment failures and their consequences have significant influence on the total operating cost of a mining system. Having this in mind, a reliability study has been initiated for loadhaul- dump machines in an underground mine. The main purpose of this study is to identify the critical machine subsystems, determine their failure pattern and help work out an effective maintenance strategy. In the first part of this study, the failure data of diesel powered LHDs, gathered during an I8-month period have been analyzed. For the purpose of the analysis, the machines have been treated as systems comprising seven subsystems connected in series. The most critical subsystems, i.e. electrical and hydraulic, were further investigated, and analyzed by graphical and analytical methods. Different failure distribution models were applied and discussed. Basic Defmitions and ConceptsIn order to avoid confusion, several terms used in this paper are defined below, as compiled by O'Connor (1991). The acronymsBS and MIL-STD stand respectively for: British Standard and US Military Standard.Failure: the termination of the ability of an item to perform a required function (after BS 4778).Time Between Failures (TBF): the length of time between two consecutive failures.Observed Mean Time Between Failures (MTBF): For a stated period in the life of an item, the mean value of the length of time between consecutive failures computed as a ratio of the cumulative observed time to the number of failures under stated conditions (after BS 4778).Maintenance, Corrective: The actions performed, as a result of failure, to restore an item to a specified condition (after MIL-STD-721 B).Maintenance, Preventive: The actions performed in attempt to retain an item in a specified condition by providing systematic inspection, detection and prevention of incipient failure (after MIL-STD-721B)."

Jan 1, 1994

By Te Gao

It is a general expectancy that in most of the construction and renovation project, the contractor is going to hand over the as-built documents to the owner or the facility management team at the completion of the project. The main challenge for the handover process is to ensure the completeness of the captured building information and the accuracy of it in terms of how well it represents the reality. Building information models (BIMs) can be used as an information repository to store and deliver as-built information. However, due to changes made in the construction and renovation phases and errors made in the design and modeling phases, discrepancies can exist between BIMs created in the design phase (asdesigned BIMs) and actual building conditions. Laser scanning technology is able to efficiently capture accurate geometric information, which provides an opportunity to identify and quantify discrepancies and update as-designed BIMs into as-built BIMs. This paper presents a case study, within which the asdesigned BIM of a newly renovated research lab was updated into an as-built BIM using laser scanned data captured in the renovation phase. This paper introduces the challenges associated with the updating process for the as-designed BIM. In order to address these challenges, this paper introduces a framework that supports the update of an as-designed BIM by incorporating point clouds captured by the progressive laser scans.

Aug 1, 2013

By R. Bridge

Mining companies are progressively finding themselves having to develop operations for more complex, deeper ore bodies, which require the use of more complicated mining and mineral processing methods. This coupled with the generally increasing trend of higher capital and operational costs have led to a need in the industry for improving ore body knowledge, mining and mineral processing. Geometallurgy is a relatively new concept that can link the three aspects, and when used effectively it is a method that can produce the necessary information for designing and building operations for reliable and optimum performance. Geometallurgy not only involves the integration of geological, mining, and metallurgical fields, but it can also be expanded to include environmental and economic information to produce a block model that can be used to obtain the best outcome in terms of plant response and plant sustainability. The geometallurgical program should not end once the block model has been populated. A detailed geometallurgical approach should be applied to all stages of the operation encompassing sample selection, through to equipment sizing and production forecasting. It can also become a useful optimisation tool thereby allowing the operation to be proactive rather than reactive against changes in the ore characteristics. With the development of metallurgical performance predictors it is possible to quantify how the ore will behave in the process plant in terms of throughput, recoveries, reagent consumption, etc. Therefore, in terms of responsible mining and sustainable resource development, a geometallurgical approach to operations is the logical step for plant development. In this paper we describe the state of the technology with respect to the application of geometallurgical modeling and its utilisation in the fields of design, forecasting and optimisation of mining operations.

Aug 1, 2013

By Edgar L. Horner

"The objectives of the Wabush Mines tailings stabilization program are to control dust Ii/t-off and to rehabilitate the disposal area. The evolution of the program started with test plots in 1970, these being continued and expanded upon through 1974. In 1976, a 35-acre vegetation field trial was attempted and failed, part of the failure being attributed to lack of adequate equipment. Subsequently, equipment was purchased and during the summer of 1979-80 extensive areas were treated. The program was also expanded to include the evaluation of chemical and water spray stabilization versus vegetation in areas where shorter-term control is required. In addition, during the summers of 1979-80, spruce bog material was spread over about 100 acres and seeded.The approach to reclamation by vegetation at Wabush is one of soil building. Work to this point indicates that iron ore tailings can be converted to a soil capable of supporting plants. Plans for the Wabush tailings disposal area should make dust lift-off from inactive tailings areas negligible within the next few years."

Jan 1, 1981

By Y. Long

The deep-hole surface blasting technique is a prime method of iron ore mining. Blasting fragmentation is one of the important economic indicators that measures the blast method to obtain the iron ore. To improve the efficiency of the blasting method and further reduce the cost of the subsequent processing of iron ore, this paper summarizes measured data gained from a certain amount of blasting test conducted in an iron ore mine in Guangdong province, China. According to the data analysis, there are differences on iron ore blasting fragmentation by different indicators of deep-hole blasting, such as decoupling coefficient of charge, contact state between charge and borehole wall, and change of detonation position in charge. These factors were compared in terms of relevance and impact. Research shows: under certain rock conditions, the decoupling coefficient of the charge has a best range related to blasting fragmentation. Since the detonation position in charge determines the direction of propagation of the explosion stress wave through ore and rock, bottom initiation and mid initiation will help to improve the iron ore blasting fragmentation in joints fractured rock and ore. The research conclusions have important application value for program design of iron ore surface blasting and to guide other types of rock surface blasting.

Aug 1, 2013

By Werner W. Scholz

A corrosion-resistant lining is, quite often, selected on the merits of its corrosion resistance only. This paper demonstrates the effects of temperature, pressure, weather, design aspects and variances of physical properties within the scope of the generic designation of a corrosion-resistant material or materials. The base for the study is a rubber- and brick-lined steel vessel, with unchanged chemical conditions. Graphs and sketches illustrate the various effects of physical influences on the selected lining specifications.

Jan 1, 1979

By T L. Horsley

The change from a seasonal to a continuous mining operation at Cassiar has been accompanied by increased emphasis on the preventive maintenance of mining equipment. This paper describes how equipment maintenance is organized, and details some maintenance practices that have proved advantageous to the Cassier operation. Introduction Cassiar Asbestos Corporation Limited is currenly carrying out an open-pit mining operation at the 6,300-foot elevation on McDame mountain in northern B. C. A 6-mile road connects the mine to the mill and plantsite at the 3,500-foot elevation. Ore concentrate is delivered to the mill via a 3llz-mile tramline. Naturally level ground does not exist in the mine area. The weather is typical of mountainous regions, exhibiting wide and rapid variations in temperature. It is generally wet and windy at the mine elevation, and a heavy snowfall is common. The rock types vary from a soft, sheared serpentine to massive serpentine, to medium-hard, friable sediments to hard, blocky volcanic flows.

Jan 1, 1964

By J. Brent Hiskey

At present, approximately 80 % of the worlds mine production of copper is achieved by smelting and electrorefining. The principle aim of copper electrorefining is to satisfy the large demand for extremely pure copper. It is remarkable that high quality copper cathodes with the required purity (99.99+% Cu, ASTM B115-10) and structural characteristics (i.e. deposit density and morphological texture) are produced from impure copper anodes dissolved in electrolytes containing a variety of impurities. This is accomplished with the proper control of operating parameters such as: current density; temperature; copper and sulfuric acid concentration; agitation; substrate preparation; and the application of electrolyte additives. The basic elements of the electrolysis of copper have not changed significantly over the past 150 years since the early developments of James Elkington. Importantly, our fundamental understanding of the underlying electrochemistry has advanced considerably. This is especially true regarding our knowledge of the mechanistic role of additives during the electrocrystallization of copper. This is a very complex subject and modern electrochemical techniques and the development of surface characterization and imaging instruments has helped immensely in our ultimate understanding of how additives control the deposit structure and morphology. The purpose of this paper is to review the historical development and application of electrolyte additives in copper electrorefining and to examine our current knowledge regarding their use. INTRODUCTION The first transatlantic telegraph cable was completed in August 1858. Regrettably, this cable failed shortly after the initial connections. After several more failed attempts, improvements in materials and copper quality resulted in successful communication between Europe and America on July 28, 1866. In many ways this hallmark event demonstrated the need for high purity copper. The first copper refinery in the world was commissioned in May 1869 in Pembrey, South Wales by partners Josiah Mason and James Balleney Elkington. (Historical Note). The 1865 and 1868 British patents issued to James Balleney Elkington were the foundation for the first commercial production of high purity electrolytic copper (Elkington, 1865, 1869, 1870). This important achievement was made possible primarily by the invention of the dynamo which was based on the fundamental operating principles advanced by Michael Faraday. A symbiotic relationship between copper refining and the dynamo was henceforth established. The dynamo provided electric current for electrolytic refining of copper and the electrorefining tankhouse provided pure copper which was required for the generation and transmission of electricity.

Jan 1, 2019

By Liguang Wang

The froth phase in flotation has received much less attention than the pulp phase despite the fact that froth stability plays an important role in determining flotation performance. Froth stability is largely determined by the stability of thin foam films, which in turn has a strong correlation with the critical rupture thickness (Hcr) of the films. In the present work, a new approach to predicting the Hcr values of thin foam films in flotation froth phase was proposed and examined. The Hcr values were calculated using an advanced capillary wave model with input parameters being surface tension, film radius, capillary suction pressure, and intersurface force. The intersurface force was estimated by using the Stefan-Reynolds lubrication approximation to fit the measured thinning rates of single foam films formed in a Scheludko ring cell, where the film radii were less than 50 microns and were kept constant during the film-thinning process. A comparison between the predicted and experimental Hcr values was made for the films with the use of sodium chloride as background electrolyte and in the presence of various frothing reagents such as methyl isobutyl carbinol (MIBC), polypropylene glycol with an average molecular weight of 400 (PPG400), and sodium dodecyl sulphate (SDS), at different concentrations and film radii. It was found that the model correctly predicted the trends of Hcr-versus-concentration and Hcr-versus-film radius curves. Moreover, the predicted Hcr values matched well with the experimental ones of the foam films containing either SDS or PPG400. For the foam films containing MIBC, however, the model overpredicted the Hcr values. The reason for this discrepancy was discussed.

Jan 1, 2016

Objectives ? New deposits can be found in mature Mining CampsNew Camps ? Volcanogenic Massive Sulfide (VMS) deposits ? polymetallicpolymetallicexamples are desirable exploration targets examples ? Genetic and exploration models for VMS deposits are robustrobust ? subtle but important differences exist between deposits and districts ? sometimes ??neglectedneglected??in resource modeling and exploration efforts ? ReRe-evaluation of a prominent existing camp is rewarding ? update on the exploration strategies currently being applied on a practical level The Falconbridge-Alexis approach includes GoCAD modelling

May 1, 2006