Search Documents

By E. G. C Charlesworth, M. J. Robertson

"Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots. Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confirmed largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semimassive sulfides within tension fractures which are folded, attenuated and fractured. An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994

By Yuki Soma, Tsutomu Ogawa, Jae Hyung Hong, Toshihiro Nagato

The Saganoseki flash furnace was built in 1973. The steel frames of the flash furnace were designed to absorb the expansion of refractories and contain expansion-absorbing materials between their frames and the skin plate. Expansion and deformation resulted in the furnace settler because of the repeated increase and decrease in temperature from more than 30 maintenance shutdowns. Preliminary investigations were conducted to confirm the condition of the settler, and it was found that partial cracks accompanied the expansion in the lower layer of the refractories. As a result, the risk of molten-matte leakage increased. Based on the above investigation, it was decided that the entire settler should be replaced by introducing a spring-displacement structure that was capable of maintaining the furnace integrity over an extended period. The difficult redesign and rebuilding of the Saganoseki flash furnace was accomplished successfully and safely in 76 days from September to December 2017, as planned. Because of various redesigns, the furnace was changed to a flash-smelting furnace that can withstand higher thermal loads based on recent trends of copper concentrate with increased sulfur and reduced copper. The new furnace is operating smoothly at present. INTRODUCTION The flash-smelting furnace of Pan Pacific Copper Co., Ltd. Saganoseki Smelting & Refinary commenced operation in 1973, with an original designed feeding rate of 71 t/h. As a result of facility remodeling and operational improvements, shown in Figure 1, the feeding rate was increased to 215 t/h in recent years. After more than 40 years of operation, the original settler in the melt holding section of the flash furnace underwent significant expansion and deformation.

Jan 1, 2019

By H. M. Howard

"The subject of Grinding Media is perhaps still quite controversial. Many people will state today that the spherical ball is the only way, and also will state that this was settled long ago others are not so sure, and I am in this second category. Over the years there have been many changes in grinding and in our evaluation of grinding media we should always be ready to review the overall situation at regular intervals. There is quite a lot of inertia in all branches of Hineral Dressing and this is particularly true of grinding or, more correctly, comminution.In order to understand some of the things which are done today, and to understand some of the thinking on grinding, it is desirable to go back some sixty years and trace the developments in comminution. In doing this we should consider perhaps three general categories with respect to daily tonnage. An arbitrary division would be under 500 T.P.D., 500-5000 T.P.D., and large operations which might have several parallel units, each with a capacity of about 5000 T.P.D. For the future, in the broad picture, this last category will be the important one because we will be more and more dependent on large-tonnage low-grade operations for most of the metals of the future. Some such division is necessary because the daily tonnage will have a very great effect on what we can and cannot do. It is also necessary to consider the entire flowsheet, and to remember in particular that grinding is not merely to make small particles but is also a conditioning process, to prepare the materi.al for the process which follows. The relationship of crushing to grinding must also be considered. It is logical to include the liners as part of the grinding media and we should try to distinguish between the wear of grinding media and the consumption of media by corrosion. Finally, the whole question of grinding media should be examined in relation to the possibilities of using some form of autogenous grinding."

Jan 1, 1970

By Norm Clegg

The Plant Engineering and Maintenance Association of Canada PEMAC is a national, not-for-profit industry association for plant and facility maintenance, engineering and physical asset management in all industry sectors in Canada. Our mission is to provide professional development for our members and the profession in Canada

Feb 1, 2008

Partnership with MiHR ? AHRC and MIHR jointly developed Mastering Aboriginal Inclusion for Mining ? Customization specific to mining Mining is unique? ? History of Aboriginal peoples and the land ? Unique community needs ? Effects of Impact Benefit Agreements ? Remoteness of mines ? 1200 Aboriginal communities located w/in 200km of active mines or exploration ? Long term effects of the land

May 1, 2009

By Xuanxue Mo, Kaihui Yang

"The Laochang mine, located in the Sanjiang area of southwestern Yunnan Province of China, is a volcanogenic massive Pb-Zn-Cu sulfide deposit. It is hosted by a pyroclastic sequence of Early Carboniferous age, namely the lower member of the Yiliu Group, which was intruded by syenite and rhyolite porphyry. The volcanic suite is basaltic or basaltic-andesitic in composition, has alkaline affInities, and is associated with the initial rifting along the margin of the Baoshan-Shanstate continental microplate (Yang, 1989). The ores are typically Pb>Zn>Cu in composition, averaging 3.820/0 Pb, 3.51% Zn, from 0.01% to 1.85% Cu (0.107% av.), a high average content of Ag (113 glt) and recoverable amounts of Au, n, Gd, Ga, Ge, In. A massive sulfide zone, in which lenticular and stratiform orebodies are localized in a sulfide-<:arbonate-silica shale unit or sulfidic tuffIte horizon that usually overlies coarse-grained pyroclastic rocks, is underlain by a stringer sulfide zone developed in a subvolcanic intrusion or volcanic sequence. The sulfIde mineral assemblages, from the top to the bottom of the deposit, are: realgar + orpiment - galena + sphalerite + pyrite - chalcopyrite + pyrite + pyrrhotite + arsenopyrite. Oxide and sulfate minerals occur rarely in the massive ores. The massive ores are generally fme-grained and banded, but coarse-grained ore, colloform and framboidal texture, and growth-zoned pyrite and sphalerite are common. Sedimentary features such as graded bedding, brecciated and deformed ore clasts, and chaotically emplaced blocks, are well preserved, indicating that the massive orebodies have undergone slumping and displacement. Alteration is weak in the hanging-wall rocks, but strong in the stringer zone. Two distinctive alteration zones have been identifIed: the upper zone, characterized by an assemblage of quartz, carbonates, chlorite, albite, zeolite and sericite, and the lower zone containing diopside, tremolite, actinolite, gamet, clinozoisite, and epidote.The general features of the Laochang deposit are in accord with the descriptive model of VMS deposits (Lydon, 1984). However, it falls into neither the Zn-Cu group nor the Zn-Pb-Cu group chemically (Franklin et al., 1981). The depositional setting of the Laochang deposit is quite different from Cyprus or Besshi-type massive sulfide deposits. Laochang is hosted by alkaline lavas that were erupted in a submarine continental rift. Although some features of the Laochang deposit are similar to those of Kuroko-type deposits, there are remarkable differences in the alteration mineral assemblage, the proportion of ore-forming elements (lead enriched) and the amounts of oxides and sulfates. These suggest corresponding differences in ore fluid composition and the associated ore-forming environment. Thus, the authors suggest that the Laochang deposit may be a distinct type of VMS deposit."

Jan 1, 1993

By Ben Cottrell

In this paper technical drilling is referred to as the process of collecting engineering and metallurgical parameters for subsequent mine design considerations. Throughout the development of a mineral exploration property there are various opportunities to ?piggy-back? technical drilling onto the routine exploration drilling process, helping to reduce future costs and delays associated with re-drilling and missing information. This article is written from the engineers and metallurgists point of view, to outline some best practices for exploration borehole planning and technical data collection requirements.

Aug 1, 2013

By F. Simon, A. Roth, M. F. Zaeh

Applying Friction Stir Welding in an industrial environment requires knowledge about the robustness of the welding process against imperfections in the joint line resulting from production deviations of the parts to be joined or from improper clamping devices. In this work the influence of gaps on the weld quality of friction stir welded butt joints of the aluminum alloy EN AW-5083-H111 is investigated in detail using the method Design of Experiments. As independent input variables, the rotation speed, the feed rate, the tilt angle, the lateral tool offset and the gap width were chosen. Tensile strength was selected as a measure for the joint quality. Moreover, the fundamental response variables of the FSW process, such as weld temperature, axial force and spindle torque, were recorded and integrated in the empirical process model derived by regression analysis. It was found that each response variable decreases with increasing gap width, whereas the largest impact was identified for the axial force and the temperature at the weld surface. In order to improve the joint strength for a given gap width, increasing the rotation speed and the tilt angle or lowering the feed rate, respectively, proved to be a suitable approach. However, interactions between the tilt angle and the rotation speed have to be considered.

Jan 1, 2014

By Karl Houseley, Dr. Robert J. Chapman

"A gravity concentration process has been applied to ores from the Clogau Mine, north Wales, the Tyndrum deposit, central Scotland and an alluvial ore from Leadhills area of Scotland. In the case of the Welsh ore and the alluvial deposit the gold grains in the concentrate and tailings streams have been characterised in terms of their three dimensions.In the case of Welsh ore, the thickness of a gold grain has been shown to be the single most important factor in determining behaviour in a gravity concentration operation. Six indices were used to quantify the overall geometry of the gold grains and those which incorporate a thickness term have proven to be effective in predicting the destination of gold particles within the concentration circuit. It is proposed that the most simple of these, the Heywoods flakiness ratio, has potential for the control of milling operations as an alternative to the established practice of characterising the size of the mill discharge.The effect of grain geometry on the recovery of fine gold has been studied using Tyndrum ore. The recovery of gold by gravity concentration increased from 20% to 70% when the criteria used to design the milling operation was the prevention of over grinding of gold grains.The destination of alluvial grains in the concentration circuit did not show such dependence on shape, and this has been attributed to the effective classification of all the gold grains in the sample by fluvial action producing a population of similar geometric characteristics."

Jan 1, 1996

By T. Belem

In-stope backfill will cure under effective stress, which develops due to a combination of mechanical consolidation (free draining material) and ??chemical consolidation?? (self-desiccation mechanism). A good knowledge of all the drainage and consolidation characteristics of cemented paste backfill is crucial for a better design of underground backfilling sequencing. From many of the existing results and studies done by various authors, as well as the availability of some in-stope backfill pressure data measurements during and after filling, it is possible of developing a procedure of backfilling sequencing. Hence, the objective of this study is to provide a guide for underground backfilling sequencing in the view of preventing the development of excess pore pressure that will affect both the stability of the barricades and the strength development of the backfill. This will be possible by considering the interaction between consolidation/drainage rate, filling rate and binder hydration rate.

Aug 1, 2013

By P. B. Marchant

"Based on laboratory and pilot scale continuous biooxidation of complex sulphide concentrates, commercial processing design and scaleup considerations are discussed. Capital and operating cost estimates for commercial biohydrometallurgical operations are summarized and potential applications of biotechnology are discussed. Biooxidation as an oxidative pretreatment alternative to enhance precious metals extraction from refractory sulphide concentrates in stirred tank reactors has received considerable attention recently due mainly to advances in the practical applicability of the process. Biooxidation of sulphides is certainly not a new process, however, application and control in large scale hydrometallurgical operations to treat refractory sulphides remains conceptual and the limited data available is restricted to relatively small laboratory and pilot scale operations. It is the intent of this paper to indicate scaleup and plant scale process design considerations for commercial bioleach circuits, based on recent operating experiences with laboratory and pilot scale continuous bioleach systems. An indication of the expected range of applications will be presented parameters for optimization will be discussed."

Jan 1, 1986

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters – usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By H. J. Oterdoom

SMS Siemag (SMS) has always been the front runner in safety aspects of electric smelter plants for the ferro-alloy and non-ferrous industry. The awareness for safety increased significantly over the past decades and SMS contributed with its design features greatly to a safer design and operation. Today, safety aspects are not only part of the smelter design but also of the overall plant layout. Explosions in electric smelters are rare, but have a huge impact on peoples’ lives, on equipment and on production. For this reason, SMS wanted to have a better overview of explosions within the smelting industry in order to see if useful statistics could be extracted. Generally, there is a lack of statistics regarding explosions in the electric smelting industry, and not enough information is collected or published. A significant portion of the explosions seems to be water related. Many companies, both operating and engineering, are trying to handle the risks of water, and apply methods to detect water leakages. Installing such a system is a management decision and management has then to make sure the system is properly implemented. The disadvantages and limitations of these systems should be carefully considered and communicated to operators and authorities.

Jan 1, 2014

By George B. Saunders

The mines in western Canada producing steam coal will find a better opportunity this year to market their product in Winnipeg - for two reasons: First, the new wage schedules, signed with local unions at each mine, have enabled them to reduce the selling price materially. Second, the duty on slack coal coming in from the United States has been raised to 50 cents, which is equal to the duty on run-of-mine coal. This has had the effect of raising the cost of mine-run to .the importer. Formerly, it was the practice to bring in slack coal under a duty of 14 cents and lump coal under a 53-cent duty and, by judicious mixing of the two, manufacture a mine-run coal at an average duty cost of about 22 cents. Fortunately, through efforts of the Alberta Government, and other friends of the Canadian coal trade, the Federal Government was persuaded to adjust the duty on slack coal as indicated. While it will be found that the Manitoba market, this season, is slightly more easy of access we have still a long way to go before we reach the desired goal. Geographically and economically the Manitoba market should belong to western Canada. However, it has been found a very profitable market for United States mines because large tonnages of coal can be shipped, practically at the convenience of the mines, via the Great Lakes, during seasons of slack business. They will therefore not relinquish this market without a struggle.

Jan 1, 1925

By James Ransford Dankwah

High sulphur carbonaceous materials like petroleum coke and rubber tyre are unsuitable as reductants in ironmaking because part of the sulphur is transferred to the reduced metal. Globally, while large amounts of petroleum coke are produced annually from the industrial processing of crude oil, billions of end-of-life rubber tyres are held in landfills and stockpiles. This work therefore investigates the potential feasibility of utilising these high sulphur carbonaceous materials as reductants in ironmaking without transferring the sulphur into the reduced metal. Composite pellets of iron oxide containing end-of-life rubber tyre (RT), petroleum coke and blends of RT/petroleum coke and petroleum coke/high density polyethylene (HDPE) were heated under argon atmosphere in a horizontal tube furnace. Reduced pellets were analysed after 10 minutes of reduction for their sulphur content. The results showed that sulphur-free metallic iron can be successfully synthesized using RT and petroleum coke as reductants. The level of desulphurisation depends on the nature of blending of the carbonaceous materials.

Jan 1, 2014

By H. E. (Buzz) Neal

"Abstract - The Labrador Trough contains world-class iron deposits which have been mined since 1954. The direct shipping of Knob Lake ores were mined at Schefferville from 1954 to 1982. Concentrate production began in 1961 in the southwest end of the Trough, with three mines currently producing concentrate and pellets at a rate of 35 Mt per year. West and north of Schefferville, several billion tonnes of taconite have been outlined in fine-grained, cherty magnetite iron formation. Several deposits of highly metamorphosed magnetite-specularite iron formation are located west of Ungava Bay. Numerous studies have shown that this medium- to fine-grained iron formation can be beneficated to 66% to 68% iron. In the area from Wabush Lake to Mont-Wright, a medium- to coarse-grained friable specularite-quartz iron formation is repeated by folding to form several large deposits. In this area, three mining operations are located with reserves and resources in the order of 5 billion tonnes.The iron deposits occur within iron formation in sediments in the extensive Proterozoic geosyncline called the Labrador Trough. Several facies of iron formation within the Sokoman Formation reflect variations in chemical composition and depositional conditions. The correlation between the mineralogy and textures is discussed to illustrate the development of different types of iron ores. This band extends for about 1100 km southeast of Ungava Bay through both Quebec and Labrador. Further south, it turns southwest past the Wabush and Mont-Wright areas to within 300 km of the St. Lawrence River. The iron formation is essentially folded and faulted along most of its length. The degree of metamorphism is variable, ranging from intense in the northern and southern portions to greenschist facies in the central portion.The stratigraphy, structure and mineralogy of the producing mines are described along with the history of discoveries. Geological input is required to achieve the strict specifications of the international iron ore market."

Jan 1, 2000

By S. Zakaria

"Inco&apos;s Automated Haulage Truck System (AHT) is a revolutionary automatic guided vehicle that performs all load, haul and dump operations without human intervention. The high level of sophistication and the short period it has been in operation has only allowed a select few Inco personnel to become familiar with the ART operation and maintenance. As an aid to operations an expert system using the knowledge gained from the experienced specialists was implemented in the field.The AHT operating and maintenance assistance expert system will reason through the information given, arrive at conclusions and give advice to operations, technical and management personnel. It will provide comprehensive real-time troubleshooting assistance for the hydraulic, electrical and mechanical subsystems of the ART. The ART expert system has many benefits to Inco which include increased skill levels of ART operations and maintenance personnel, reduction in ART downtime, standardization of troubleshooting procedures and reduction in ART operating and maintenance costs. In the future, the expert system application will be linked to SCADA (Supervisory Control and Data Acquisition), maintenance and statistical software to display current and historical trends of variables from a centralized historical database. As well, a wide variety of features will be integrated into the system including AutoCad drawings, graphics, photographs, voice and video capabilities."

Jan 1, 1994

By T. McCallum, B. Wellbrook, T. Ratnaweera

Leaching of copper (Cu) concentrates produces elevated concentrations of Cu and acid, which makes solvent extraction (SX) processing more challenging. Maintaining extraction targets can be more difficult with higher pregnant leach solution (PLS) grades, and variability of PLS Cu and acid can lead to increased chemical iron transfer. Diluting concentrate leach feeds with an existing heap leach inventory makes SX processing easier. However, considerations about how much to dilute and where to distribute the flow into the SX configuration must be carefully evaluated, given their impact on metallurgical performance. In this paper, characteristics of a concentrate leach feed are discussed, along with considerations for processing by SX. Also reviewed are pilot plant results of concentrate leach distribution into SX and plans for commercial testing. INTRODUCTION Hydrometallurgical processing of copper concentrates continues to gain interest from the industry. Treatment by smelting and electrorefining continues to dominate, accounting for ~80% of global copper production, but is faced with its own challenges (Li et al, 2017). The case for increased hydrometallurgical processing has been discussed as high grade ore deposits are diminishing, capital costs for smelting are high, and the environmental aspects present challenges for sustainable practice. The hydromet copper industry is also turning a corner as easily leachable copper oxide deposits are depleting, and excess SX-EW capacity exists in certain regions. The transition to hydrometallurgical processing of copper concentrates will take a bit of effort as leaching of copper sulfides is difficult and byproduct credits must be considered. Various POX leaching processes have been studied and proposed to the industry as viable practices. Of the many processes, commercial use has been practiced with the Mount Gordon Copper Process, total and partial pressure oxidation by Freeport-McMoRan at their Bagdad and Morenci, Arizona complexes, the Sepon Copper Process in Laos, and the bioleach BIOCOP™ process in Chile (Dreisinger, 2016).

Jan 1, 2019

By Daniel Gendron, Luc Morin

"Concentrate sampling is a growing concern in the world's mining and smelting industry. The main modes of transportation for concentrate to the smelter are by truck or rail car in a bulk form, thereby limiting access to sample extraction equipment. In many cases, concentrate is shipped to a smelter by several suppliers therefore requiring individual manipulation of different customer samples in a safe and reliable manner. The Heath & Sherwood Bulk Product Sampler offers this feature as well as an economical and effortless way of obtaining samples in rail cars or truck boxes.In 1994, Noranda Metallurgie in Rouyn-Noranda, Québec purchased a self contained Bulk Product Sampler to extract samples directly from inside rail cars before unloading the concentrate. After testing and comparing the results with the conventional sampling method, the bulk product sampler proved to be a practical and advantageous solution for concentrate sampling both for the customer and smelter. Since its installation at the Horne smelter in Rouyn-Noranda, the Bulk Product Sampler has been steadily used on rail cars which contain concentrates from around the world."

Jan 1, 1996

By W. Evans, T. Steis

"Sulphide ores under certain circumstances will react with explosives to generate an autocatalytic chemical reaction. This reaction is exothermic and results in the production of large volumes of poisonous gases and creates an unsafe, unstable condition with the possibility of a low energy deflagration or even a detonation of the loaded hole. This paper outlines the conditions that need to exist for such a reaction to take place and the precautions necessary to minimize or eliminate the problem in areas of reactive ore. A special case study involving a northern Ontario mine will be detailed.IntroductionOne of North America&apos;s leading underground gold producer&apos;s processes over 6500 tonnes of ore per day from an orebody containing high concentrations of sulphides. After six years of problem free operation, the mine experienced two serious reactions in two months between the sulphides and AMEX II, the ammonium nitrate and fuel oil explosive it uses."

Jan 1, 1995