Search Documents

By John Emery, George Wang

Research and applied utilization activities for the increased use of ferrous and nonferrous slags in construction are presented. The overall use of blast furnace slag is relatively well known for a range of construction applications from aggregates to slag cements. In contrast to blast furnace slag, which is volumetrically stable and straightforward in its construction uses, steel slag contains hydratable oxides that can result in volumetric instability that must be dealt with through appropriate steel slag aging, testing and quality control to ensure its appropriate use. Particular care must be taken to prevent potential steel slag expansive behaviour in confined applications. Quality requirements and guidelines on steel slag expansivity to further the use of steel slags, with demonstrated acceptable performance, are outlined. There is a full range of proven construction uses - from aggregate to cementitious materials - for copper, nickel and phosphorus nonferrous slag. The use of air-cooled nickel slag is presented, based mainly on practical highway construction experience. It has been shown that air-cooled, crushed nickel slag can be an excellent aggregate in granular base, engineered fill and hot-mix asphalt. There is a good potential for increased ground, granulated copper and nickel slags use as supplementary cementitious materials that is being developed, which takes advantage of the 'latent energy' content. The scope of a new technical text in preparation on the technology of slag utilization is reflected throughout to provide a practical context for the engineer.

Jan 1, 2004

By H. Wilhelm, W. I. van Drunick

The Anglogold Ashanti (AGA) Navachab single stage SAG mill has provided an excellent setting for incremental optimization. Over the past decades, several interventions have resulted in marked improvements in specific performance; including steel ball scat removal, re-design of the mill lifters, replacement the pebble crusher and cyclone cluster, as well as the use of a vibrating screen in place of a discharge trommel. Recent initiatives now include an operating fine DMS circuit, studies on pre-crushing of the ROM feed and also fine-screening as an alternative to hydrocyclone classification. The current optimized state of the Navachab mill allows it to operate at approximately 20% higher efficiency when compared to mills of similar shell dimensions in gold mining, treating similar ore. This paper describes the systematic improvement of the SAG circuit to its current state.

Jan 1, 2012

By Robert B. Parsons

"The Canadian tax treatment of mining operations outside Canada is not as attractive as the treatment of Canadian operations. Further, the Canadian company that invests abroad a host of complex rules. This month, Tax Notes examines some of the major Canadian tax considerations confronting the Canadian company that wants to invest abroad. IntroductionCanadian-based mining companies are investing abroad more than ever before. These foreign investments trigger a complex set of tax rules that are distinct from the rules that apply to Canadian investments. In most cases, careful tax planning is mandatory if the company's tax liabilities are to be minimized. This article summarizes the main tax considerations that need to be taken into account with respect to a mining investment outside Canada.Branch Versus SubsidiaryOne of the first questions that arises in connection with a prospective foreign investment is ""Should we invest directly (that is, in a branch operation), or should we invest through a foreign subsidiary?"". In the case of a branch operation, the Canadian company owns and operates the business directly - that is, the foreign business assets are part of the Canadian legal entity. In the case of a foreign subsidiary, the foreign business operation is owned and managed by that subsidiary. The tax treatment of a branch and a subsidiary can be quite different."

Jan 1, 1994

By O. Laitinen, M. Rudolph, J. A. Sirviö, H. Liimatainen, R. Hartmann, University of Oulu

The increasing complexity of the ores composition worldwide calls for suitable collectors with specific properties, such as selectivity, wettability, and in regard to current regulations, environmental sustainability. Therefore, collectors have to satisfy many features to improve the efficiency of flotation processes. Cellulose nanocrystals gain more and more interest due to the versatile synthesis routes which enable the integration of specific functional groups and components with different degrees of hydrophobicity within the molecular structure. Consequently, cellulose nanocrystals can be employed in flotation processes as depressant or collector molecules, respectively. Nonetheless, the usage of cellulose nanocrystals is still limited due to a lack of the characterization of nanocrystal-mineral interactions and the change of the surface wetting properties of minerals after adsorption phenomena between nanocrystals and minerals. In these studies, butyl-amine cellulose nanocrystal (BAC) and quartz are used as model system to investigate physicochemical properties of both, BAC and quartz, and examine the applicability of BAC in flotation processes. Therefore, the surface charge distribution and electrophoretic mobility of BAC and quartz are investigated and compared to understand the effect of electrostatic interactions between BACs, and BAC and quartz. Based on this, the adsorption of BAC on quartz is examined. Finally, microflotation experiments test the efficiency of BAC to be used in flotation processes. The flotation response is correlated to the specific surface charge of BAC revealing the dominant effect of surface charges on effective particle-bubble adhesions.

Jan 1, 2016

By Art Hamilton

The Zn-Pb-Cu-Ag ore deposits of the Boundary and N-5 zones near Bathurst, New Brunswick, occur in a polydeforrned volcano-sedimentary sequence that is part of the Ordovician Tetagouche Group. Massive and disseminated sulfides are hosted by an argillaceous to cherty sedimentary sequence that is stratigraphically Wlderlain by a siliceous fragmental unit and is overlain by a feldspar-rich crystal tuff and related tuffaceous rocks. The deposits have a low iron sulfide content relative to that of most stratabound sulfide deposits of the Bathurst-Newcastle mining district. The ore is commonly associated with chlorite- and talc-rich sediments. The N-5 deposit is considered to be the fault-displaced extension of the Boundary deposit. The Boundary deposit is estimated to contain 891 000 t grading 3.31% Pb, 7.96% Zn, 0.32% Cu and 44 g/t Ag; the estimate for the N-5 zone is 330 000 t grading 3.24% Pb, 7.15% Zn, 0.33% Cu, and 37 g/t Ag. The ore is processed at 1000 tpd at the Heath Steele mill.

Jan 1, 1992

By Robert MacPhail, Louis Racine, Bret G. Cousins

"Sodium Isopropyl Xanthate is employed in a wide variety of sulphide flotation procedures due to the specificity over other xanthates and the cost savings over other sulphide collectors such as thionocarbamates, xanthogen formates and dithiophosphates. An investigation carried out by Tennants Research Technology Applications (TRTA), has produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries.Currently, FLEX 31 is manufactured at the Prospec Chemicals xanthate plant in Fort Saskatchewan, Alberta, Canada. Prospec, founded in 1983, produces approximately 4500 tonnes of xanthates per year and is presently undergoing expansion to produce approximately 6000 tonnes. The proprietary process for FLEX 31 is a new addition to plant operations that include the production of xanthates, thionocarbamates and xanthogen formates.This paper will cover the testwork on the zinc flotation circuit at the Louvicourt Mine in Val d'Or, Quebec. This testwork indicated that FLEX 31 could replace SIPX due to the ability of the FLEX to improve zinc flotation kinetics without adversely affecting final concentrate grade. FLEX has presently replaced SIPX in the zinc circuit at Louvicourt.BackgroundThe Louvicourt deposit is hosted by greenschist facies Archean volcanic rocks located in the southeast portion of the Abitibi Greenstone Belt. In the Val d'Or area, the volcanic rocks form an east-west striking, steeply dipping and south-facing sequence composed of thick mafic and ultramafic flows of the Lower Malartic Group.The joint venture has three partners-Aur Louvicourt Inc. (30%), Novicourt Inc. (45%) and Teck Corp (25%). Aur Resources holds 30% interest through Aur Louvicourt, a wholly owned subsidiary and is the operator of the project. Novicourt Inc. is 60.9% held by Noranda.Approximately 75% to 85% of Louvicourt's revenue comes from the sale of copper; 10% from gold (in the copper concentrate); 7% from zinc and 3% from silver (also in the copper concentrate) The copper at Louvicourt is fairly ""fast floating"". About 60% of the copper in the ore can be concentrated in the first flotation cells with feed grades of approximately 4% copper.The initial testwork and pilot trials had indicated that it would be difficult to achieve zinc grades over 52% and recoveries would have to be kept at a level amenable to salable concentrate grades. The actual mill results, with a fine regrind, achieved zinc grades of 55% to 56% at about 75% recovery."

Jan 1, 1996

By R. Hagiwara, S. Kobayashi, K. Yasuda, T. Nohira, K. Kondo

To establish a process for the electrochemical recovery of rare earth elements from used magnet scraps, the electrochemical formation of RE-Ni alloys in molten NaCl-KCl-RECl3 salt at 973 K was investigated. Cyclic voltammetry and open-circuit potentiometry indicated the formation of several phases of RE-Ni alloys. The formation potential for each RE-Ni alloy phase was determined from the results of scanning electron microscopy and X-ray diffraction of alloy samples prepared by potentiostatic electrolysis of a Ni plate electrode at various potentials. The optimum electrolysis conditions for the separation of Nd, Dy, and Pr are discussed.

Jan 1, 2014

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By M. F. Goudge

THE present century has witnessed an amazing transformation in the uses of limestone. From being mainly a structural material, a role it has played since the beginning of civilization, it has become one of the in-dispensable raw materials for use in the great chemical and metallurgical industries that play such a vital part in the economic life of the nations today. Its uses have become so diversified and numerous that it enters, directly or indirectly, into nearly every phase of modern life. In this introductory paper it is proposed merely to outline the general usefulness of limestone and to point out some of its salient features, and to leave any detailed discussion of uses to the papers that follow. The term limestone as herein used embraces all kinds from the variety known as high-calcium limestone, which is composed almost entirely of calcite, to the dolomitic variety, composed largely or entirely of the mineral dolomite. Lime is simply calcined limestone and, in considering the uses of limestone, the uses of lime should also be included, particularly in view of the fact that, in many processes, it is possible to use limestone in either the raw or the calcined state.

Jan 1, 1939

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationships in fact discernable.

Jan 1, 2011

By R. W. Nice

"For many decades the incidence of a highly active graphite-like ore has plagued the McIntyre mine. This ore acts as a precipitant of the gold complex immediately upon formation of this complex. The gold is subsequently discharged with the tailings.Many different methods have been devised by various researchers all of which proved inapplicable for the McIntyre problem.Recently, McIntyre personnel, through their own research, developed a flowsheet. This circuit should give an overall recovery of 36% which is below the 94% experienced in the mill at present. Therefore, less revenue would arise from treatment of these ores. On the other hand there exists a possibility of more efficient mining methods in some of this ore thus allowing more economic recovery.INTRODUCTION This paper has been prepared to serve two purposes:i) To propose a method of recoverying gold from a sizeable orebody at the McIntyre mine at Schumacher.ii) To summarize and present the many methods suggested to solve a very old but very real mineral dressing problem familiar to the industry as long as cyanidation itself."

Jan 1, 1971

By B. D. Wood, J. A. Fowler, H. S. Grütter, J. M. Kong

Abstract- The phased approach used by De Beers for diamond exploration is briefly outlined. The Victor kimberlite is one of 19 kimberlites in a cluster near Attawapiskat, Ontario. The progress at the Victor kimberlite is summarized, and the operations are described within the framework of this staged approach. An evaluation program is currently under way on the Victor kimberlite, but although results are encouraging, insufficient diamonds have been recovered to permit disclosure of estimates for the grade and value.

Jan 1, 2001

By David F. Machuca-Mory

Modelling the geometry of a vein is a crucial step in resources estimation. The resulting models are used as mineralization domain boundaries and have a direct impact on the tonnage of estimated resources. Deterministic models are often built using time consuming wireframing techniques usually based on hand interpretation of the drillhole intercepts. Another approach consists in coding the drillhole samples by a function of their distance to the veins contacts. The coding is subsequently used for modelling the vein contacts away from drillholes. This is a more efficient approach and is able to provide a measure of tonnage uncertainty. The use of location-dependent variograms improves the modelling by incorporating local changes in the anisotropy of the vein structure. This combined approach results in more realistic vein models, particularly when the geometry of the vein has been are altered by folding, shearing and other structural processes. The approach is illustrated on a realistic case study.

Oct 1, 2009

By H. Zniber El Mouhabbis

Ore dilution or stope overbreak increases the cost of production and ultimately reduces the profitability of a mining operation. The adverse economic impact of ore dilution is due to the added costs associated with the mucking, haulage, crushing, hoisting, milling, and treatment of waste rock or low grade ore in the hangingwall and footwall. One factor that could have a significant influence on stope overbreak is the undercutting of the stope into the walls. Undercutting stope walls is often necessary, in particular in narrow vein mines. Moreover, equipment size has a role in drift sizing where stope undercutting may become a must in order to fit the mobile equipment while respecting legal clearances.

May 1, 2009

By J. F. Shirley

"Very seldom, if ever, is a molybdenite by-product plant operated exactly the way the process design engineer visualizes it. The best thing the design engineer can do is provide a sound, basic circuit with enough room and flexibility in order that the operating staff can make the necessary modi fi cations to optimize the process. The plant, with minor modifications, should be capable of handling more than one process. This is especially true when the client is having the plant designed for a new process.The writer would like to propose the following ten ""rules-of thumb"" for designing by-product molybdenite plants where the molybdenite is floated out of a copper concentrate. The term rules-of-thumb is used, because there are probably valid reasons for not using one or more of them in a particular plant design. In fact it was 1980 before the writer was all owed to start up a plant where all of these rules were honored in the plant design. This was after 19 years of experience in the design of molybdenite by-product processes and plants. The main reasons for not following the rules are available capital, available space, and the client's experiences based on pilot plant and laboratory test results."

Jan 1, 1981

By Jamie W. Pardy

The objective of the Canadian International Development Agency program is to facilitate the efforts of the people of developing countries to achieve self-sustainable economic and social development in accordance with their needs and environment. The British Columbia Ministry of Energy and Mines (BCMEM) is the executing agency for the four-year Peru Minerals and Metals Public Sector Assistance Project which began in December 1998. The primary beneficiary is the Ministerio de Energía y Minas del Peru (PMEM). The project is designed to address mine health & safety, environmental management and mineral resource information. Project activities currently underway include joint development of: an inspection system, a mine rescue system, an enhanced and e-Commerce capable mineral information website, environmental guidelines for industry and standardized ministry evaluation criteria for environmental impact assessments and closure plans. In addition, reports on management options for mineral concentrate transportation, storage and handling, and on mine reclamation security policy have been delivered at workshops.

May 1, 2001

By Mahmoud Shakeri1

Various types of thin-walled structures have been frequently used as energy absorbers to mitigate the adverse effects of impact and hence protect the vehicle structure under consideration when subjected to different loading conditions. Compression tubular structures that buckle in a progressive manner, can be used to advantage, providing inexpensive and versatile, but nevertheless weight and stroke efficient energy absorbers. In this paper quasi-static nonlinear finite element simulations are performed to study the effects of number of corners of the cross-section, wall thickness, plastic hardening rate of material, foam-filler and load angle on deformation mode and mean crushing force of tube. Crush strength increases as the number of corners of the cross-section increases, though it almost saturates for the number of corners beyond 11. Higher plastic hardening rate stabilizes the collapse pattern. Foam-filled tubes seem to have higher critical load angles in oblique loading and display a more stable and gradual decrease in mean load over the transition region. Substantial decrease in the initial peak load and dynamic load at any a given deflection was observed as the load angle increases. The investigation of bitubal arrangements and Multi-cell tubes reveals that these may be preferable to monotubal specimens due to the presence of the inner profiles. In addition, a comparison is conducted between the numerical and experimental results of the mean forces of some special angle elements. Good agreement is obtained.

Oct 1, 2011

By F. W. Crossland

Losses of metal are often traced to incorrect pH/ORP signals in flotation, leaching, extraction, electrolysis, and precipitation processes, aggravated by pressure changes. IC Controls, a Canadian mining sensor manufacturer, developed a new superior pH/ORP sensor that stops metal losses, reduces environmental footprint and contributes to sustainability. The cause of incorrect pH/ORP signal is rooted in the reference. Reference junctions are designed to allow diffusion of reference chloride ions into the process but also allow process ions to diffuse into the reference. This development is important to mines and hydrometallurgists where sulphide, cyanide, ammonia and other poisoning ions are present in the process. These ions react with reference electrolyte components causing the signal to change, drifting from the correct process value. With fluctuating process pressure, ion in migration dilutes the electrolyte producing similar signal drifts. If process ion in-diffusion could be stopped, the pH/ORP signal would be accurate. IC Controls new pH/ORP sensor stops process ion in-diffusion, and remains accurate over long periods. New processes using higher pressure and fluctuating pressurized reactors will greatly benefit from stable pH readings. Similar to IC Controls' proven model 642 Mining pH sensor, our new model 647 contributes to sustainability through reducing disposal costs from waste reagents, lost metal and fewer used sensors.

Jan 1, 2014

By J. A. Dubinski

One of the greatest threats of mining in hard coal mines are underground fires, which in the past often resulted in the mining disasters. Implementation of scientific principles of fire fighting into practice contributed to a significant reduction of fire hazard in coal mines. However, despite numerous achievements of science in the fight against the underground fires, they still occur creating a potential hazard for the miners and contributing to generate significant costs of fire-fighting operations, the temporary suspension of production or loss of longwalls. This concerns both spontaneous fires and exogenous ones. A significant decrease in the number of spontaneous fires was the result of cooperation between Polish scientists with experts in the field of new methods of fire hazard prediction and selection of new fire prevention and fire hazard monitoring methods. A significant part played here researchers from the Central Mining Institute. The original method of endogenous fire risk assessment based on calorimetric tests of coal and developed mathematical model of the process of coal self-heating allow to predict the risk of spontaneous fires and select proper fire prevention measures adequate to the involved risk. The frequency of exogenous fires is in the last few years is low, but their share in the total number of fires is relatively high and constitutes about 30%. This results from the prevention activities, carried out regularly in mines which are aimed at reducing the fire hazard connected with the use of fire-resistant conveyor belts and other non-metallic materials. Further directions to reduce the hazards connected with underground fires should focus on improving the methods for monitoring hazards together with automation of fire fighting operations.

Aug 1, 2013

By G. P. Cooper

A comprehensive computational heap leach model was used to evaluate options for operating a chalcocite-ore heap leach process. The stockpile leach model is based on the computational fluid dynamic software framework PHYSICA+ and incorporates various physical and chemical phenomena to simulate fluid transport, mineral reaction kinetics, bacterial effects, and heat, energy and acid balances for the overall leach process. The leach model is calibrated against small-scale column leach tests, and simulation results are validated against closely controlled column pilot-scale tests. For a given set of ore conditions, the effects of raffinate irrigation rate are examined. Several options for pulse leaching were investigated, and the effects on copper recovery and pregnant leach solution (PLS) grade are described. Model simulations indicated that pulse leaching could be used to control copper grade of the PLS. Finally, an analysis of inventory issues is presented for various lift heights including multi-lift simulations to examine potential operating options. U sing irrigation rate, raffinate copper grade, and lift height as variables in a factorial design of experiments, the simulations showed that raffinate copper grade is the main factor that affects the soluble copper inventory grade.

Jan 1, 2007