Search Documents

By Weldon Li

Outline ?Introduction and Motivation ?Previous Research ?Details ?Findings ?Current Multi-Piece Mining Wheel Research ?Methodology ?Preliminary findings ?Current and Future Activities ?Summary and Closing Remarks

Oct 1, 2010

By G. Langlands

"R. Tenbergen Is this flotation machine suitable in the flotation ofInco ball mill discharges where we have a coarse feed at 60% solids?Reply Experience has shown that there is not a significant increase in the wear life of these machines when handling coarse material (8 mesh) at 60% solids. A common practice in Europe is shut down on the week-ends.The material is allowed to settle and on start-up an injectic of air for 15 seconds is sufficient prior to start-up. At,mining we put our unit in the middle of a bank of 44 cells and in order to ensure severe sanding we shut the aker cell down while the remaining cells kept running. After 20-25 seconds of air the cell started without trouble.P. Mahant Is there a build-up inside the impellor shaft housing? Falconbrige Ltd.Reply There is no sand build-up but rather a scale build-up which due to a flexing action frees itself periodically. Part of the design of the machine permits a water injection into the shaft housing to free any build-up. This is done in Europe during the week-end shut down."

Jan 1, 1984

By Arnaud Faucher, Amar Sabih, Sudarshan Martins, Tristan Martin, Sami Makni, Peter Radziszewski, Poorya Hosseini, Francois-Raymond Boyer

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By Franco Chiesa, David Levasseur, Bernard Duchesne

A 500kg aluminium AlSi7Mg03 casting has been poured and the metallurgical quality at different locations inside the casting has been thoroughly investigated. It included measuring the local tensile properties (YS, UTS, El) in the T6 condition, the dendrite fineness (DAS) and the level of microporosity. A correlation was found between the microporosity level, the local solidification time and solidus front velocity; this correlation allows to predict the porosity level in large aluminium castings (solidification times between 20 and 200 minutes). Quite expectedly, properties varied widely within the casting and the actual mechanical properties were much less than the "textbook values" based on measurements carried out on separately cast standard specimens. A correlation between the secondary dendrite arm spacing (DAS) and the local solidification time was in keeping with previously published data. Finally the conditions to obtain an acceptable finish on machined surface were determined.

Jan 1, 2014

? Introduction ? Partenariat MRNF - MAE ? Goldex ? Manitou : - Ré-aménagement du bassin versant - Accès aux zones problématiques - Filtration du ruisseau pour les travaux - Nettoyage près de la rivière - Régulation du débit et bassin - Digues et bassins - Déposition résidus Goldex ? Chemins d?accès Goldex-Manitou ? Pipelines: Goldex ? Retour Goldex ? Manitou ? Station de pompage ? Résumé

Feb 1, 2008

By Bernard Tougas, Franco Chiesa, David Levasseur, Bernard Duchesne

"In the present paper, the optimization of a tilt poured permanent mold will be carried out using filling and solidification modeling. This exercise resulted in 3 modifications of the initial mold design which was based on the foundry experience. The optimization provided a 20% improvement in the yield while increasing the output from 10 to 15 castings per hour.In a subsequent study, the value of the critical fraction solid of AlSi7Mg (A356) alloy was verified by radiographic analysis of the castings produced in the first 5 cycles of a run, which are necessary to bring the mold to a dynamic thermal equilibrium."

Jan 1, 2014

By G. Couture

In the introduction to this presentation, we will cover the market of motorized recreational products. We will introduce the public to what is produced and sold worldwide, what is the nature and general behaviour of the customers for such products. We will cover the evolution of this market and put in evidence how drastic must be the changes in the manufacturers organizations in order to, in one hand, constantly adjust to the customer demand, and in the other hand, react to the competitors' offensives on the market.

Jan 1, 2006

By R. G. Bradburn

"Brenda Mines Limited is a low grade open pit mining and milling operation located near Peachland, British Columbia. The mill was brought into production in late 1969 at a rated capacity of 24,000 tons per day. Tt currently treats an average of 30,000 tons per day of an ore that has an average grade of 0.130% copper and 0.030% molybdenum.Description of Crushing and Grinding CircuitsRun of mine ore is delivered to a primary gyratory crusher. The minus seven inch product is separated into plus and minus one inch fractions on two parallel vibrating screens. The fine product is conveyed directly to the mill fine ore bins, while the coarse fraction is sent to a 45,000 ton stockpile.Material from the stockpile is fed to two standard cone crushers which operate in an open circuit with five secondary vibrating screens. The minus five-eighth inch product from these screens is conveyed to the mill fine ore bins while the coarse fraction is fed to four shorthead cone crushers. These crushers operate in closed circuit with the screens."

Jan 1, 1981

By M. Schwarze

SMS Meer GmbH with its COPPER PLANTS DIVISION produces a full line of systems and machines for the processing of copper. The product range includes: shaft melting furnaces, anode casting lines, horizontal and vertical casting lines, casting and rolling lines for copper wire rod and strip, cold pilger mills, planetary rolling mills as well as tube drawing equipment. The new designed shaft furnaces are the most economic way of copper melting. The CONTILANOD® system with hydraulic shear represents a breakthrough into higher production capacities and improved geometrical accuracy of anodes. The new generation of CONTIROD® lines with individual drives of rolling stands guarantee cost effective production of highest rod quality. A new horizontal continuous casting technology for the production of tube shells as feed stock for the copper tube manufacturing process ? directube® was developed and introduced into production. A first line for continuous vertical strip casting - called VERTICAST® - for higher production rates and improval quality of cold-rollable strips is in the final stage of commissioning. These innovative technologies increase product quality, reduce process costs and help for a wide use of copper in all sectors of life.

Jan 1, 2007

By G. J. Desroches, E. Ozberk, M. J. Collins, B. D. Krysa, I. M. Masters

The zinc refinery of Hudson Bay Mining and Smelting Co., Ltd. went through a major modernization in 1993, when the roaster and the calcine and fume leach circuits were replaced by a new Sherritt zinc pressure leach plant. The HBMS plant, in Flin Ron, Manitoba, represents the first commercial application of the Sherritt two-stage zinc pressure leach process, with /00% of the zinc concentrate feed processed in autoclaves. The process design of the new plant required definition of the deportments of elements such as antimony, arsenic, chlorine, cobalt, fluorine, germanium, magnesium, manganese, selenium, tellurium and thallium. This paper describes the deportment of these elements in the commercial zinc plant during the first nine months of pressure leach operation, and compares these results with operations prior to the introduction of pressure leaching, and with the results of tests carried out in the She"itt laboratory during the process development phase.

Jan 1, 1995

By William DeWit

When rivers are contaminated from industrial operations, as often occurs near repositories of spent mine tailings, decision-support tools can be critically important in evaluating the effectiveness of various engineering impact-management measures. Even where data describing river flows and quality are sparse, simple mixing-zone models can be constructed that can contribute greatly to understanding how impact-management measures can differentially affect existing river-chemistry regimes. There can be circumstances where accumulated surface waters near contaminated land can bear contaminant loadings that could be acceptable to river regimes if there were methods available to evaluate optional discharge rates and to predict post-mixing consequences on river chemistry. Nomographs can be constructed to evaluate discharge regimes that appear capable of releasing contaminated accumulated pond water without compromising water quality in a nearby river. River-mixing zone models also contribute to predicting rates of acceptable discharge and release to the receiving environment.

May 1, 2011

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

For developing new technologies, it is important to characterize the microstructure of materials with high spatial resolution at the nanoscale. To achieve high resolution, field emission scanning electron microscopes (FE-SEM) were developed. These microscopes allow working at low accelerating voltage, below 5 kV, to take advantage of the reduction of the interaction volume with accelerating voltage. Furthermore, their higher gun brightness compared to conventional thermo-electronic emitters, allow a probe size at the nanoscale. At low accelerating voltage, the emission volume of backscatter and secondary electron (SE) of the type II signals approach that of SEI signals. However, it is not enough to reach the highest resolution. A magnetic field above the sample improves the spatial resolution by collecting mostly high-resolution signals. In addition, the energy-filtration of the electron signals allows selecting the type of contrast detected: topographic, compositional, or crystallographic. The development of these new technologies permits to extend the imaging capabilities of the SEM towards new nanoscale applications.

Jan 1, 2014

By Maureen A. McGuinness

Kidd Mine, an Xstrata Copper operation in Timmins, Ontario, operates a 400 t/h pastefill plant that provides paste backfill to stopes at the depth of 9000 ft. This paper will cover the operating practices of the pastefill plant both on surface and underground, highlighting tailings excavation, paste mix design and the pipe maintenance program. Kidd Mine, une opération d'Xstrata Copper à Timmins, Ontario, opère une usine de remblai d'une capacité de 400 t/h. Le réseau de distribution permet d'acheminer le remblai en pâte juste qu'à une profondeur de 9000 pi. Cet article couvrira le mode opératoire de l'usine de remblai tant à la surface que sous-terre en mettant l'emphase sur l'extraction des rejets miniers, la recette du remblai en pâte ainsi que le programme d'entretient du réseau de distribution.

Feb 1, 2008

By P. Condori, G. Rech, J. Winnett

"Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken.A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material.Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores.This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit."

Jan 1, 2012

Presentation Overview ?? Project Setting ? Project Context ? Challenges ?? Managing Commitments ?? Project Update ?? Maximizing Aboriginal Economic Participation in Resource Development PROJECT SETTING ?? Developed on the traditional lands of the Labrador Inuit, and the Labrador Innu ?? Courts have held that Aboriginal peoples in Canada possess special rights to traditional lands ?? Rights can include requiring resource developers to enter into Impacts and Benefits Agreements ?? Development agreement with Newfoundland and Labrador was required

May 1, 2004

By Pierre Laliberté

Objectifs ?Quantifier les économies d?énergie potentielles liées àl?utilisation de différentes technologies ?Créer un modèle permettant d?évaluer les économies possibles d?énergie en combinant plusieurs technologies ?On ne peut simplement additionner les pourcentages d?économie individuels pour en évaluer le total.

Feb 1, 2008

By Y. Konishi

This paper reviews the mechanism and kinetics of bioleaching of chalcopyrite by the thermophilic archae Acidianus brierleyi in batch and continuous-flow reactors. Rate data for the batch bioleaching of chalcopyrite concentrate were collected to clarify mechanism of the chalcopyrite bioleaching with A. brierleyi. The chalcopyrite leaching was markedly accelerated in the presence of A. brierleyi, and greater than 90% copper leaching was achieved within 10 days. Chalcopyrite leaching took place predominantly as a result of direct attack by adsorbed bacteria on the sulfide surface, the chemical leaching with ferric iron being insignificant. Batch rate data collected under a variety of operating variables were analyzed with our batch bioleaching model, in order to estimate microbial kinetic and stoichiometric parameters for the microbial growth on chalcopyrite. The batch model and the estimated parameter values were used to find optimum operating conditions. Moreover, the batch model was extended to describe the bioleaching in continuous-flow stirred tank reactors. Simulations based on the continuous reactor model and the estimated parameter values were used to predict the leaching fraction as a function of the number of reactors connected in series.

Jan 1, 2007

By J. C. Ingles

"A survey of possible methods for controlling cyanide concentration indicated that the simplest method would involve the use of a potentiometric technique. Such a method was suggested by a paper from the laboratory of Mines Safety Appliances, which described a method for determining hydrogen cyanide in air. In this application, the cyanide was absorbed in caustic and a silver electrode immersed in the caustic solution provided a measure of the cyanide concentration. However, our attempts to use the silver electrode in this simple manner to measure the cyanide concentration of solutions were not very successful. A study of the mechanism by which a silver electrode responds to cyanide concentration made it evident why this simple procedure is not satisfactory.Basically, the silver electrode provides an indication of the free silver ion concentration of a solution, and generally speaking, ignores the other ions' present. It can be used to measure an anion if this anion complexes silver. This technique has been used in complexing studies to determine the activities of such anions as acetate, citrate, oxalate and chloride. To do this, the electrode has to be placed in a solution which initially contains a known concentration of free silver ions. Addition of the complexing anion causes a drop in the free silver ion concentration and hence a change in the potential of the silver electrode. The change in potential can be expressed in terms of the concentration of the complexing anion, and used to indicate its concentration in the solution being analysed. The determination of chloride-ion by a silver-silver chloride electrode is an example of an application of this technique. The solubility of the silver chloride with which the electrode is coated provides the initial free silver-ion concentration. Depression of this free silver-ion concentration by the presence of the excess chloride ion of the sample solution results in a change in the potential of the electrode which is proportional to the chloride-ion concentration."

Jan 1, 1965

By Owen Owens, W. P. Armstrong

The process of arriving at the size and grade of: (a) a newly-discovered body of mineralization, (b) a potential ore resource, (c) an orebody proposed for mining, or (d) the ore reserves in a mine, requires fundamental geological, and geometrical determinations as well as physical and chemical analyses. This paper outlines geological and geometrical features considered critical, in the authors' experience, in realistic reserve determination. These are discussed under the headings "The Four Cs". They include the Character, type or nature of the mineralization; the Continuity of various types of mineralization in the deposit; various key concerns in the Calculation besides the mathematics; and the Classification section which refers to basic considerations in classifying a mineral estimate. It is suggested that the responsibility for the calculation of a Resource or Reserve should be that of a geologist experienced in the ore type under review. Further, it should be the responsibility of the board of directors of the company owning the deposit to ensure that a sufficiently experienced person is chosen to carry out the process.

Jan 1, 1993

By Louise Laverdure

Outline ?Background ?Issues and considerations ?Why do we need to innovate ?Green Mining Initiative ?Footprint reduction ?Innovation in waste management ?Ecosystem risk management ?Mine closure and rehabilitation ?The Future

May 1, 2011