Search Documents

By John Monhemius

Looking back over the past half century, it can be seen that the growth in the importance of hydrometallurgy for the production of non-ferrous and precious metals almost exactly parallels the rise of the environmental movement and its principal NGOs, such as Greenpeace and Friends of the Earth. The paper will review important landmarks in the development of the science and technology of hydrometallurgy and show how many of these have been influenced by pressures on the industry brought about by environmentalists. Successful innovations as well as commercial failures will be considered and reasons for the success or failure will be analysed and lessons drawn to guide future developments.

Jan 1, 2014

By T. Cutard, E. Yeugo Fogaing, C. Gault, H. Marzagui, N. Prompt, M. Huger, C. Deteuf

This paper deals with studies made in the field of the French research network PROMETHEREF. Several refractory castables are considered in this program. In the present paper, one of these materials is considered, it is a low cement castable based on andalusite aggregates. A particular attention is paid to microstructural changes during the first heating and on their effects on the high temperature mechanical behavior. Microstructural evolutions have been characterized by the way of dilatometry, scanning electron microcopy and X-ray diffraction. In-situ observations by environmental scanning electron microscopy gave complementary results on these high temperature microstructural changes. They deal with microcrack formation, phase changes, crystallization, liquid phase formation and sintering. By propagation of ultrasonic waves, high temperature continuous measurements of the Young's modulus have been made. Results confirm the existence of microstructural changes and allow to quantify the Young's modulus variations all along specific thermal cycles. High temperature four point bending tests and room temperature tensile tests were made in the same temperature range. Behavior evolutions could be found and interpreted with the help of previously mentioned results.

Jan 1, 2004

By Grazyna Zakrzewska-Trznadel

The paper outlines the main objectives of the project that concern the evaluation of the possibility of uranium production from indigenous resources since Poland enters the nuclear program. The best available technologies are considered for uranium extraction and obtaining the yellow cake - U3O8. Liquid-liquid extraction with novel extracting agents, as well as membrane processes for separation of by-products will be tested in course of the project. The technological part will be completed with techno-economical analysis. Acknowledgement The studies were supported by the POIG project, No 01.01.02-14-094-09-00 ?Analysis of the possibility of uranium supply from domestic resources?.

Aug 1, 2010

By J. Zinck

The management of mine wastes generated by both active and inactive mining is an ever more challenging issue. The cost to manage and treat mine wastes, including tailings, waste rock, treatment sludge and slag, is estimated at over $50B in Canada and the United States alone. Cost-effective technologies are required to meet both short and long term challenges and increasing environmental standards. This paper will provide an overview of novel and conventional technologies to manage mine waste particularly in the areas of waste stabilization, treatment and disposal technologies.

Jan 1, 2004

By A Frostick

Ranger uranium mine is surrounded by the World Heritage listed Kakadu National Park and offsite impacts resulting from mining at Ranger would affect the Magela Creek catchment first. Radionuclides, lead isotope ratios and metal concentrations were measured in sediment cores from the Magela Creek catchment around Ranger to investigate the dispersion of mine-derived particulates. The study found a localised area within the Ranger mineral lease, where upper sediments had elevated levels of radionuclides and trace metals and radiogenic Pb isotope ratios. There is no current evidence of sediment dispersion from Ranger further downstream within the Magela Creek catchment.

Aug 1, 2010

By George P. Demopoulos, Amani Al-Othman, Terry C. Cheng

One critical issue in chloride hydrometallurgy is the regeneration of the lixiviant HCl that is currently achieved by pyrohydrolysis. In this paper, a low temperature HCl regeneration process was investigated which regenerates HCl and produces saleable gypsum. This process promises to reduce the generation of wastes by the reaction of spent calcium chloride leach liquors with sulfuric acid solution at low temperature. Experiments were performed to determine the optimum conditions of the reaction in terms of temperature, reagent concentrations, rate of reagent addition, mixing and seeding/recycling to produce marketable gypsum and HCl with practical strength.

Jan 1, 2004

By D. L. Chen, Q. Zhang

The effect of particle sizes on the low cycle fatigue (LCF) life of discontinuously reinforced metal matrix composites (DR-MMCs) has been widely studied. However, how the particle size affects the LCF life of DR-MMCs quantitatively is still lacking. The aim of this investigation is, therefore, to present an analytical model linking the LCF life to the particle size. This model, based on the enhanced dislocation density in the matrix and the load bearing effect of particles, showed that a decreasing particle size results in a longer LCF life, and the results predicted are in good agreement with the experimental data.

Jan 1, 2004

By Trung Nguyen

Midwest is a unique uranium deposit with exceptionally high arsenic content. The ore body is located 17km west of the McClean Lake operation. The McClean Lake mill will be modified to process Midwest ore and handle solid wastes coming from the Midwest water treatment plant. This paper describes the modifications required of the McClean Lake mill, process challenges associated with treatment of the arsenic, and the possibility of recovering nickel and cobalt as a by-product. It also reviews the complexity in the design of the Midwest water treatment facility which incorporates reverse osmosis technology with conventional physical-chemical water treatment.

Aug 1, 2010

By M. F. Vancas

Control of the interface elevation between the aqueous and the organic phases in typical settlers is a fairly straight forward principle. However, when looking at the details involved in actually designing the aqueous and organic discharge launders and weirs, one comes to realize just how sensitive the system is to small variations in operating conditions and/or parameters. This discussion focuses on the details that must be considered during design, looks at the various types of control systems typically used (from the basic manual systems through to full automation), and equally importantly, looks at what happens in an operating plant when the conditions and/or operating parameters change.

Jan 1, 2007

By S. Orr

In situ leaching is a complex, multidisciplinary process, which requires both mastering and integration of the different disciplines involved. Particularly, in-situ leaching is the intersection between geology (geochemistry, mineralogy, structural geology), hydrology (hydrogeology, well hydraulics), metallurgy (hydrometallurgy, electrochemistry, aqueous chemistry), and economics (mineable ore, cost of operations, market). The management of such a complex system requires all relevant knowledge base, integration, and continual optimization. Our presentation starts with a description of the "expert system" ? from data acquisition to information and knowledge, including determination of essential in-situ parameters, analyses, and modeling, which ultimately leads to an integrated, real-time, hierarchical management/control system.

Jan 1, 2007

By W. M. Silva, PAP. Miotto, M. A. P. Silva, V. P. Ramos, L. R. M. Bittencourt

The major cause of breakdown of anode baking furnace fluewalls is chemical corrosion, which leads to deterioration of the properties of the bricks. Subsequent deformation of the fluewalls occurs, and also extensive cracking of the lining is observed. The present work studies the major changes of the brick during the operation of the furnace, after 22, 60 and 90 cycles of baking; in two different regions: upper and lower. Due to excellent cleaning conditions of the butts, negligible amounts of fluorine were found in the bricks. The major contaminants found were carbon, sulfur and alkali compounds, all of them present in the anode baked during the process.

Jan 1, 2004

By S. A. Beeson, C. Poole

"This paper reports on the development of selective flocculation processes for the direct recovery of KCl values from low-grade Canadian sylvinite and carnallite potash ores.Two reagent suites, consisting of either a non-selective cationic or selective non-ionic flocculant, together with the same selective anionic dispersant, were evaluated. Initial data from component mineral behaviour investigations, reagent adsorption studies and selective flocculation tests on a synthetic potash ore were used in the successful development of processes capable of recovering KCl values without the necessity for desliming to remove water-insolubles.Enhanced multi-stage treatment (involving redispersion and reflocculation) and subsequent floc recovery techniques (including sedimentation, hydrocyclones and froth flotation) were examined, and in all cases the influence of process parameters such as reagent dosages, conditioning times, solids concentration, particle size and other physical design criteria were investigated.The data reported clearly demonstrate the scale-up potential of these processes and possible applications in potash operations."

Jan 1, 2000

By Blandine Arseneault

The Raglan Mill had been in production for less than a year when the initial toxicity tests on the effluent revealed that it was defined as ?toxic? under regulations. Testwork was begun to address the fundamental reasons for the toxicity and a systematic approach was initiated to identify causes. Elimination of the problem presented a challenge once the main conclusion identified high dissolved solids as the principal culprit. In particular, normally benign soda ash (sodium bicarbonate) reagent additions used in milling, was identified as the main contributor to the problem. Following analysis of all requirements and safety considerations, a concept to recycle 100% of the mill process water was pursued. In addition to meeting regulatory requirements, this project would have numerous positive benefits to the operation, including reducing fresh water consumption and lowering costs.

Nov 1, 2002

By B. T. Lu, J. L. Luo, H. X. Guo

This paper investigated the synergistic effect in the slurry-erosion process of carbon steel. In line with the mechanisms of material loss, the synergism due to interaction of erosion and corrosion was divided into the corrosion enhanced by erosion and erosion enhanced by corrosion. The erosion-corrosion tests were conducted with A1045 steel in slurries containing silica sand. Experimental results showed that the rotating of the sample in corrosive media raised both OCP and corrosion rate, but the impingement of solid particles did not affect the corrosion current significantly. In the quiescent solutions, the Faraday's law gave a good prediction for the weight loss caused by corrosion but for rotating samples, the weight loss experimentally measured was virtually greater than that predicted by the Faraday's law, indicating that the corrosion-enhanced erosion could occur in corrosive fluids in absence of solid particles. A half-logarithm relationship was observed between the weight loss due to corrosion-enhanced erosion and the anodic current density.

Jan 1, 2004

By Y. C. Kim

This paper discusses Air Liquide's patented SPALTM (Surface Protection Air Liquide) technology and process for the inerting of coreless induction furnaces using cryogenic liquid gas. Air Liquide Canada Inc., in collaboration with Riverside Brass and Aluminum Foundry Limited (Riverside Brass), conducted plant trials to demonstrate the applicability of the SPALTM technology for copper-based alloys. Results showed that with SPALTM, Riverside Brass benefited from a significant increase in metal yield as the level of dross formation was drastically reduced. Together with the many other benefits of this technology, SPALTM demonstrated to be a non-negligible cost-effective solution to reduce metal production costs. In an effort to optimize the argon flow, different flow rates were used and the oxygen level above the metal bath was measured to pinpoint optimal flow. The results of metal yield, charge mix, dross formation, and melt temperature are compared with and without argon. The metal yield improvements are dramatic and calculated net savings are presented hereunder.

Jan 1, 2007

By J. Scalise

The paper covers a wide range of topics relative to filtration for continuous cast copper and aluminum. Subjects include system concepts, filtration concepts, system components, filter types, filter media selection, caster water filtration, coolant disposal, and recommended materials of construction.

Jan 1, 2007

Introduction Gold Mining is an Important Economic Activity in Canada n Total value added during 1990-99 was $15.5 bn n The gold price is an important factor in the value added process n The gold price affects gold mining output, profits, exploration expenditures, employment, etc. Some Factors that Affect the Gold Price n The value of the US Dollar affects the US Dollar price of gold: a weaker US$ correlates with a higher gold price n Supply affects the gold price: the higher the supply on the market each year, the lower the average gold price that year Central Bank Gold Sales n Yearly central bank gold sales add to supply, and affect the price of gold negatively n The negative impact on the price of gold reverberates through the Canadian gold mining industry n Despite the modest amounts, even Bank of Canada gold sales affect the Canadian gold mining industry

May 1, 2003

By Ch. Wenzl

Anodes must have a certain physical and chemical quality in order to provide uniform anodic corrosion and meet the requirements of electrorefining, i.e. to achieve a high current efficiency, low energy consumption, low amount of anode scrap and low effort together with high cathode quality. Various properties of the anodes can be influenced directly by the casting process, which is the interface of pyro- and hydrometallurgy of copper. The aims of anode casting ? high output and long mould lifetimes ? are not consistent with good physical anode quality. The physical requirements of an anode are smooth surfaces, uniform weight and thickness, minimal edge effects, minimal distortion of the body and the lugs, as well as a homogeneous microstructure, in order to achieve uniform dissolution behaviour. The chemical quality of the anode copper is a task of electrorefining operations, but the elemental distribution within the anodes, which should be as homogeneous as possible in order to provide uniform anodic corrosion, can be influenced by the casting process.

Jan 1, 2007

By Paul D. Young, Michael J. Allan

"The Con Mine has been producing gold continuously since 1938. In 1990 laboratory and pilot plant investigations began into the use of pressure oxidation for treatment of an arsenic trioxide waste product from two previous roaster operations on the property. This led to the construction in 1992 of a 96 ton/day plant to treat a mixture of arsenic waste and flotation concentrate from the existing mill. The plant was commissioned in the fall of 1992.This paper describes experience gained in the commissioning and initial operation of the plant. The unique aspects of treating a hazardous waste product are described including special operating procedures to satisfy environmental and employee safety concerns. The paper further describes modifications made to the process flowsheet, to operating procedures and to materials of construction in the early months of operation."

Jan 1, 1994

Polymer electrolyte membrane (PEM) fuel cell has increasingly become the potential choice of zero-emission power source for portable, mobile and stationary co¬generation applications. However, technical barriers need to be overcome before its widespread commercialization; cost reduction and performance improvement including reliability are the two key areas, that can be realized through better cell/stack design and improved understanding of the transport processes occurring inside the individual cells and stacks. In this presentation, we will provide an overview of various cell/stack models that are available in the literature, their strength and weakness, and then present a comprehensive multi-species, multi-phase and multi-dimensional formulation of a single PEM fuel cell, with consistent and systematic formulation for all the regions involved, including the solid bipolar plates, gas flow channels, the electrode backing layers, the catalyst layers and the electrolyte membrane. Such a detailed approach allows us to extract sufficient information to the analysis of a stack of PEM fuel cells. Stack model will be presented that investigates the various stack designs and flow configurations, and the optimal stack design based on the present study will be described. Also some innovative cell/stack designs will be featured.

Jan 1, 2005