Search Documents

By M. J. Hadianfard

The effect of holding at temperature on fatigue life of a 10 vol% particulate SiC reinforced Titanium alloy has been investigated. The influence of holding time at 600°C on fatigue of this material has been studied by using tension-compression tests, scanning electron microscope and image analysis. The specimens were heated to 600°C by using a controlled atmosphere furnace; hold at this temperature for time ranging from 0 to 100 hours, and then fatigue tested at room temperature under controlled constant plastic strain. The number of cycle to failure found to decrease with increasing of the holding time. In addition the fracture mechanism and number of debonded particles has been significantly influenced by holding time at 600°C.

Jan 1, 2004

By E. Paransky, M. Rigaud, G. Paschek, S. Palco

Some of the negative impacts of carbon addition on the strength of castables are yet to be overcome in order to fulfill its potential benefits for oxidation resistance. This paper reports the results of recent studies conducted at CIREP on the effects of different types of carbon additives on the thermo-mechanical properties of magnesia-based castables. Experimental techniques included measurements of the hot modulus of rupture (HMOR), hot modulus of elasticity (HMOE), as well as the wedge-splitting test (WST). The comparison of evolving microstructures was carried out employing scanning electron microscopy with microanalysis attachment (SEM/EDS) and X-ray diffraction (XRD). HMOR values of 12 MPa at 1300°C have been reached in MgO-Si02-C castables containing up to 7% carbon.

Jan 1, 2004

By L. Treadgold

The KOV, Kananga and Tilwezembe copper-cobalt deposits in the Democratic Republic of the Congo have lain dormant for over ten years due to lack of funding by the State-owned mining company, Gecamines. Nikanor Pic through its operating company DCP has secured the mining titles from the DRC government and has commenced redevelopment of these large copper deposits. DCP plans to produce 250,000 tonnes per annum of LME Grade "A" copper cathode and up to 30,000 tonnes per annum of cobalt salts. This paper describes the geology, re-development of the KOV mine and the two smaller mines, Kananga and Tilwezembe, the design of a new copper-cobalt processing facility and the challenges in refurbishing the associated infrastructure.

Jan 1, 2007

By D. Allen

Faced with decreasing ore grades and harder ores, many mines today are forced to become more efficient with their approach to processing. Variability in ore hardness, mineral liberation, reagent consumption, sliming, and leach responses are all a function of the minerals present and their concentration. Modern semi-automated X-ray Diffraction (XRD) analyses using Rietveld refinement techniques, in conjunction with high speed quantitative Near Infrared (NIR) analyses, provide reliable quantitative mineralogical ore profiling. By the implementation of XRD with NIR, mining, milling and leaching operations no longer need to be dependant on visual estimates for GeoMetallurgical Modeling and are provided with a valuable forecasting and production control tool. This paper will illustrate the development, plant implementation and application of XRD and NIR at several copper operations.

Jan 1, 2007

By C. Sorel

The solvent extraction systems devoted to uranium purification from crude ore to spent fuel involve concentrated solutions in which deviation from ideality can not be neglected. The Simple Solution Concept based on the behaviour of isopiestic solutions has been applied to quantify activity coefficients of metals and acids in the aqueous phase in equilibrium with the solvent. This approach has been validated on various solvent extraction systems such as trialkylphosphates, malonamides or acidic extracting agents both on batch experiments and counter-current flowsheets. Moreover, this concept has been successfully used to estimate the aqueous density which is useful to quantify the variation of volume and to assess criticality parameters such as number density of nuclides.

Aug 1, 2010

By R. Ham-Su, J. P. Healey, S. P. Farrell, R. S. Underhill, M. A. Gharghouri, C. V. Hyatt, L. M. Cheng

Magnetic shape memory alloys (MSMA's) are a class of materials where magnetic energy can be converted into mechanical energy and vice versa. NiMnGa-based MSMA's have attained magnetic field induced strains up to approximately 10% and have a relatively wide operating temperature range, from well below 0°C to above RT, making them very attractive for a variety of applications. However, these materials also suffer from low toughness. Using these materials in a composite could mitigate this shortcoming, and also overcome limits imposed by inertia and eddy current losses. In this work, we describe the manufacture and characterization of such composites. Composites with 30% by volume MSMA were fabricated under a magnetic field resulting in anisotropic magnetic properties. Damping properties were evaluated by dynamic mechanical analysis.

Jan 1, 2004

By M. Solomon

Abstract -Giant, sediment-hosted lead-zinc deposits in northern Australia formed during development of Mid-Proterozoic extensional basins that overlie Lower Proterozoic basement. The basement in the Mount Isa area, exposed by folding and faulting, contains fractionated, high-heat-producing granites. These granites generate heat at a rate of about 6 ?Wm-3, probably sufficient to form giant lead-zinc deposits either by (a) driving episodic convection of saline basement and basin fluids for periods of 105 to 106 years at temperatures of about 230°C, or (b) heating basin fluids moving under the influence of topographic relief or fault movement. The presence or absence of such granites may form a vital component of the genetic model. Ore-forming fluid flow was probably initiated by continent-scale, extensional basin fracturing.

Jan 1, 1992

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By Z. Mubarok

An overview of the problems encountered the electrorefining of copper anodes containing high levels of nickel and antimony is presented. Our investigations have been focusing on the passivation behaviour of the anodes with high contents of Ni, Sb, Sn, and Pb, the formations of kupferglimmer and floating slimes. The results of linear voltammetry, chronopotentiometry and electrolysis test revealed a noticeable lower resistance of the anodes to passivation in comparison to those with lower contents of Ni, Sb, Sn, and Pb. Anode containing kupferglimmer exhibited oxygen gas evolution during the passivation state. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) indicated that tin can replace and/or join antimony in the kupferglimmer structure. Under specified experimental conditions, floating slimes precipitations took place with high Ni, Sb, Sn, and Pb anodes prior to the end of one anode period.

Jan 1, 2007

By T. Watanabe, M. Nakagawa, K. Kimapong

Ultrasonic wave was irradiated on metal surface in water to introduce compressive residual stress. The ultrasonic wave that was oscillated with 19.5 kHz ultrasonic transducer and amplified with a step type horn was irradiated. Slight plastic deformation occurred at the surface region of pure metal such as Cu and compressive residual stress was introduced. It seemed that the plastically deformed depth from the metal surface corresponded approximately to the depth of introduced residual stress. The higher compressive residual stress could be introduced into the surface of Cu-Zn brass and SUS304 stainless steel because work-hardening was simultaneously induced to those alloys. Furthermore, since martensitic transformation was induced by the plastic deformation in the case of SUS304, the compressive residual stress could be introduced more deeply into the surface region. The residual stress of SUS304 reached to the maximum value of 574 MPa by irradiating for 5min.

Jan 1, 2004

By G. C. Weatherly, D. S. Wilkinson, A. M. Limarga

In addition to the harsh environment, materials for high-temperature applications are often subjected to a significant mechanical loading. Several researchers have noted that the rate of oxidation can be affected by stress in a range of materials. We have recently studied this effect in y-TiAl, based on the preliminary work of Magnan and Weatherly which showed that nitridation rates on the tensile side of a flexural creep specimen could be 10 times higher than on the compressive side. We have since developed a four-point bending creep setup capable of controlled atmosphere testing. We present quantitative data on the effect of creep on scale growth under a range of atmospheric conditions. Finite element analysis will also be used to show how modest applied stresses can have a large effect on scale growth rates through the generation of large stresses due to the mismatch of creep rate between the metallic substrate and the scale.

Jan 1, 2004

By R. Ramirez

Atlantic Copper Refinery (Huelva, Spain) has operated the ISA permanent cathode technology since 1995. The current production rates are 260,000 t/y cathodes and 730 t/y anode slimes. These slimes undergo an atmospheric leaching in which their copper content is reduced from an average value of 24 % to 16 %. In June 2005 an optimization study of the leaching conditions was carried out aimed at lowering the copper content in the slimes to less than 8%. At the same time, a new mixer (Outukumpu Technology GLS-mixer) was installed in one of the three leaching reactors. As a result of the improvement of the leaching performance and to prevent the return of tellurium to the tankhouse, a cementation plant was commissioned in July 2005 to ensure a Te content below 50 ppm in the Cu-rich leachate. This paper describes the results of the improvement of the leaching conditions and the operation of the new tellurium removal plant.

Jan 1, 2007

By B. T. Lu, J. L. Luo, T. Yu, C. W. Chen

In this paper, the synergism in erosion-corrosion process occurring in oil sand wastewater transportation caused by the interaction of mechanical and electrochemical factors was experimentally investigated. The erosion-corrosion tests were conducted with A1045 steel in synthetic slurries comprising tap water and silica sand. The material loss due to corrosion-enhanced erosion was assessed with the chemo-mechanical model developed by the authors recently. The results indicate that the material loss produced by corrosion-enhanced erosion at the open circuit potential can be formulated as a linear function of logarithm of corrosion current density. The wastage caused by the erosion-enhanced corrosion was analyzed based on the concept of non-equilibrium thermodynamics. The material loss induced by the erosion-enhanced corrosion is approximately a linear function of overall erosion rate measured in synthetic slurries, indicating that erosion-enhanced corrosion could be reduced by adopting surface strengthening techniques to improve the resistance to the plastic deformation in surface layer.

Jan 1, 2004

By Christopher W. N. Anderson

Induced hyperaccumulation of gold by plants was first reported in 1998 by researchers from Massey University in New Zealand who proposed the idea of mining gold using plants (phytomining). Since that time research has been conducted to understand the conditions under which plants can be made to take up economic amounts of the metal. One key focus has been on the geochemistry of gold-rich soils, leading to a diagnostic test that can predict how suitable a particular soil might be to gold phytomining. Field trials have been conducted at several locations around the world in collaboration with industry partners. A Decision Support System has been developed to assist in the design and management of phytomining operations, and economic modeling has been carried out to set targets levels for phytomining technology. Novel studies are now examining the form of gold in plants. Research suggests that plants may store gold as discrete metallic nanoparticles in leaf and stem tissues, an observation that may lead to new ways to recover the metal from harvested biomass.

Oct 1, 2003

By D. Runnels, A. Allaire, J. Fournier, Y. Sylvestre, F. Robichaud

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By Serge Vézina

Environmental issues have evolved considerably over the last two decades. The main contributing factors, to name a few, have been the changing values of our modern societies, the globalization of trade and its linkage to environment, evolution and accessibility of information/communication technologies, better educated populations, climate change, long range transport of toxics and the increasing influence of NGOs and multistakeholders. As well, environmental management of mining operations had to be realigned in order to meet these new realities and to respond to more elaborated regulations oriented towards sustainability. Environmental Management Systems (EMSs) have emerged and have been introduced to meet not only the assurance of conformance to regulations but also to prevent pollution and to apply the continuous improvement of mining processes. EMS models have been developed and certification to international standards (e.g. ISO-14 001) is a common practice. Globalization has imposed challenges and additional requirements to environmental management. Developing a mine in emerging countries implies dealing with international agencies, local communities and a variety of government infrastructures to obtain a ?licence to operate?. This paper presents the structure of our EMS and how we have adapted its implementation to our operations in South America.

May 1, 2003

By Larry M. Southwick

Processing of ores to recover metals usually generates large amounts of waste materials, such as rejects from concentrating operations, tailings from leaching and slags from smelting. These wastes often contain substantial amounts of iron and other metals, recovery of which are often considered to be of commercial value. Earlier versions of this paper investigated a number of processes built to recover iron from a variety of copper processing residues. This paper will extend that coverage to residues from nickel/cobalt, aluminum, asbestos and oil shale processing and coal plant fly ash. Products of interest are iron, ferroalloys, magnesium and aluminum. While none of these processes achieved long-term commercial success, their efforts cover the gamut of problems that must be addressed in treating dirty and difficult materials to recover generally low-value products. An Adept is an alchemist who can create a Philosopher's Stone, which could transmute base metals into gold. In 1701 in Berlin one Johann-Freidrich Böttger, a nineteen year old apothecary's apprentice, told King Frederick I that he could discover how to make the Stone. He failed and fled Frederick's wrath to Poland. He failed again, and King Augustus II threw him in jail. Then, in 1709, he discovered instead the secret of making Dresden china, certainly a more practical search. His failures in alchemy led to the nickname Adeptus Ineptus.

Jan 1, 2004

By J. Fournier

A novel sol ? gel (SG) synthesis procedure utilizing varying ratios of glycine and ethylene glycol to total metal cations has been developed to create high purity nanometer sized La0.65Sr3.5MnO3 powders. X-ray powder diffraction (XRD), transmission and scanning electron microscopy (TEM, SEM), and dynamic light scattering (DLS) have confirmed that the crystallite sizes of such powders are ~ 20 nm, and the aggregate particle sizes vary between 100 to 300 nm. Mixing varying weight percents of SG LSM powders with commercially available Praxair LSM in a composite LSM/YSZ functionally graded cathode has been shown, through the use of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), to exhibit enhanced oxygen reduction kinetics vs. at conventional cathode materials.

Jan 1, 2005

By J. Fournier

A novel sol ? gel (SG) synthesis procedure utilizing varying ratios of glycine and ethylene glycol to total metal cations has been developed to create high purity nanometer sized La0.65Sr3.5MnO3 powders. X-ray powder diffraction (XRD), transmission and scanning electron microscopy (TEM, SEM), and dynamic light scattering (DLS) have confirmed that the crystallite sizes of such powders are ~ 20 nm, and the aggregate particle sizes vary between 100 to 300 nm. Mixing varying weight percents of SG LSM powders with commercially available Praxair LSM in a composite LSM/YSZ functionally graded cathode has been shown, through the use of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), to exhibit enhanced oxygen reduction kinetics vs. at conventional cathode materials.

Jan 1, 2005

By Frederick Biery

Outline ? Project Challenges ? Results from 100 recent projects ? What factors are driving the best and worst projects ? A look at recent mining projects ? Conclusions

May 1, 2009