Search Documents

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

New York City is an urban environment with a history spanning over 200 years. The coastline of New York has changed over the years. In the East River, old bulkhead and remnant of relieving platforms together with variable bedrock elevations pose challenges in the design and construction of deep foundations. This paper presents a Case History of high capacity deep foundations along the Franklin D. Roosevelt (FDR) Drive on the Upper East Side in New York City. The project consists of a ramp that overpasses the FDR Drive allowing heavy trucks to access the Marine Transfer Station (MTS) facility built over the East River. Large diameter drilled shafts and mini-piles socketed to bedrock were designed and constructed. Remnant of old bulkhead was encountered at the site and a Ground Penetrating Radar (GPR) investigation was completed during the subsurface investigation phase of the design. This paper discusses details of the subsurface investigation program and design methodology of the high capacity drilled shafts and mini-piles. It also describes construction methods and results of Osterberg Load tests documenting the field values of skin friction through the rock socket. Other construction challenges include construction and drilling rock sockets for drilled shafts over sloping bedrock. 1. INTRODUCTION New York City is a renowned urban city that always calls for the most delicate, yet complex, and robust superstructures and most importantly substructure designs. The historic preservation of this large 200 years old city of 319 square miles is ever changing. Shorelines are often extended to accommodate new infrastructure and very often many miscellaneous structures are discovered below the ground surface. The East 91st Street Ramp was constructed to provide access to the East 91st Street Marine Transfer Station over FDR Drive and York Avenue. Another alternative ramp will be relocated to the South Bound (SD) of the FDR Drive at 92nd Street. A subsurface exploration program was completed in accordance with the New York City Department of Design and Construction (NYCDDC) general requirements, Section 4.5, to perform subsurface investigation along the FDR Drive in Manhattan, New York.

Jan 1, 2019

By Ahmed H. Bukhary, Naser A. Al-Shayea

The objective is to assess the overconservatism in the parameters used for designing offshore piles. Methodology includes analysis of shaft friction data obtained from more than five different locations in the Arabian Gulf, consisting of 40 piles to depths up to 86 m. Reports were collected for both the dynamic pile monitoring system (DMS) and their corresponding geotechnical reports based on the American Petroleum Institute (API). The values of shaft capacity for the sand layers were analysed by comparing those based on API to the corresponding DMS values. Results of the comparison of the data from these reports showed that the pile design parameters obtained using API guidelines is generally smaller than that measured by DMS. The difference is presented in terms of an overconservative factor (OCF) which is adjusted based on statistical nonparametric test performed on the two data sets. The adjusted OCF were found to be 1.79 and 2.00 for carbonate sand at (loose to medium dense) and (dense to very dense) conditions, respectively. The corresponding values for silica sand were only 1.2 and 1.06. In conclusion, based on the evaluation conducted for data from these reports, the API shaft friction is overconservative for carbonate sand. The API shaft friction for piles in sand can be increased by multiplying it by the adjusted OCF.

By Pirooz Barar

The new Stanley Hall building will house the center for bio-engineering and technology research for the UC Berkeley campus. The structure is located at the northeast part of campus, adjacent to Donner Lab, on the west side of Galey Road, approximately 600 ft. from the Hayward Fault. The building site has a complex geological formation. To the east there are clayey soil shale formations, and to the west there is greywake shattered sandstone. The water table is at 10 ft. below grade. The structure will consist of 6 levels below grade and 8 levels above grade, which calls for an 83 ft. deep excavation on the northeast side. There is an approximately 35 ft. grade differential between the east and west sides of the building. Because of this severe grade differential, as well as high water tables, the lateral forces on the building due to uneven earth pressures would have been 2 times the magnitude of the seismic forces. To mitigate the lateral earth pressures, a permanent Soil Nailed Wall, integrated with the structural system of the building was designed. PB&A, Inc.?s in-house design program ?Winslope? was utilized to design the system and the data obtained from a rigorous monitoring program, were used to calibrate several computer runs using Plaxis program.

Jan 1, 2004

By Hitendrabhai S. Dewangan, Dr. Aashish A. Mehta

Pile foundation is widely used in construction of marine structures. In offshore & marine piling work, drilling/boring supporting fluid is used to stabilize the borehole (excavation) prior to tremie concrete. The poly-fluid is a synthetic drilling granular polymer characterized by high molecular weight.it is mainly used for the preparation of stabilizing and lubrication mud in drilling of deep foundations. Disposal of polymers after using it into the sea, pollutant the sea environment, which may be harmful for living organisms inside sea. To reduce the pollution in offshore/Onshore, it is essential to take the precautions during flushing operation with proper recycled, reused & it’s Disposal. To provide economic and environmental solutions, used slurry was treated with addition dose of fresh material/polymers. The amount of fresh materials/ Polymer to be added can be decided based on (viscosity, density and pH value) test results. Finally, initiate water flow and air agitation as required. Run the tests on the re generated slurry before transferring to storage tank. Also, after storage, polymers will be reused for next operation. Moreover, mud wastage coming from borehole will also be disposed at suitable dumping places.

Sep 1, 2022

By Scott Dodds

"The Oxford Hydroelectric Station was a unique project that incorporated a variety of dam strengthening methods to stabilize the facility in order to meet the standards required by Federal Energy Regulatory Commission (FERC). The dam stability and Probable Maximum Flood (PMF) remediation work consisted of (1) construction of a new emergency spillway; (2) installation of 75 high capacity rock anchors; (3) construction of an anchored concrete powerhouse buttress; (4) construction of cast-in-place and sheetpile flood walls; and (5) design and construction of a permanent soil nail wall. INTRODUCTIONThe Oxford Hydroelectric Station is one of 11 hydroelectric facilities owned and operated by Duke Power along the Catawba/Wateree River. The Catawba River originates in the foothills of the Appalachian Mountains just west of Morganton, North Carolina. The river flows east out of the mountains and, at a point just below the Oxford Dam, the Catawba River turns and heads southeast. The Catawba River continues to flow southeast past Charlotte and into South Carolina where it eventually becomes the Wateree River. The Wateree River eventually flows in to the Atlantic Ocean.Located a few miles east of Hickory, North Carolina, the Oxford Dam and Hydroelectric facility is in the upper reach of the Catawba River. Oxford Dam creates the third impoundment along the river known as Lake Hickory. Lake Hickory is well known locally for providing many outdoor activities such as boating, jet skiing, canoeing and fishing. The dam and powerhouse were put into operation in the spring of 1928.Key features of the dam include a short embankment section on the south end of the structure, a 391-foot (119m) long south bulkhead and powerhouse, 540-foot (165m) long gated spillway section and a 235-foot (71.6m) long north bulkhead. The maximum height of the dam is approximately 100-feet (30m) from the crest to the dam/rock interface. (See Figure 1).The work associated with this project is the result of licensing requirements of the Federal Energy Regulatory Commission (FERC) which mandates that all hydroelectric facilities have the capacity to safely discharge runoff created by a critical rainfall event defined as the probable maximum flood (PMF). Duke Power, a division of Duke Energy (DUKE) submitted an initial PMF report in 1992 which indicated that at the Oxford Dam would be overtopped by approximately 10-feet of water during the modeled PMF event. Given the duration and depth of the overtopping, significant damage to the facility and a possible breach could result. Therefore, modifications to the existing facility were necessary to satisfy the report of the PMF model."

Jan 1, 2005

By C. Dai, S Raathiv

The Waikato Expressway is one of the New Zealand Transport Agency’s (NZTA) seven roads of National Significance. Coffey is part of the City Edge Alliance engaged by NZTA for the Hamilton Section of the project. The 22km Hamilton Section is the largest and most geotechnically complex section of the Expressway. The Mangaonua gully in Sector 6 is the most challenging geotechnical area of the project for piling works. Together Coffey and Brian Perry Civil have carried out the temporary and permanent design and construction of embankments, piling works, retaining walls and soil improvement works for the bridge construction. The design and construction works were governed by weak alluvial layers and artesian pressure layers several meters beneath the ground level. This paper presents the action taken to improve the foundation of temporary platform, control the artesian pressure, prevent bentonite leakages into the highly permeable alluvial layer and challenges in the base grouting process. This paper summarises the key components in the construction and supervision of bored piling works and outlines innovative solutions for challenges which we faced during the construction.

Nov 1, 2022

By George Burnhart

"Sonic drilling is a relatively new technology even though it has been in development since the late 1940s. It was initially funded by the U.S. petroleum industry and then, in the late 40s, Russian scientists worked on developing sonic drilling, their interest based on drilling rates 3 to 20 times that of conventional methods. In the early 1960s, the Shell Oil Company backed research that resulted in a down-hole device with a series of eccentric weights driven by drilling fluid to generate vibration. Hawker Sidley, in the early 1980s, developed the first modern prototype sonic drills in Vancouver B.C. and the North Star Drilling Company in Minnesota became the first contractor in the U.S. to operate sonic equipment in 1985. In 1994, North Star became a division of Boart Longyear, headquartered in Salt Lake City, Utah.What’s Unique about a Sonic DrillA sonic drill rig appears and operates very much like any conventional top-drive rotary rig. The key difference is that a sonic drill has a specially designed hydraulically powered drill head, containing oscillators, that generates adjustable high-frequency vibratory forces. The sonic head is attached directly to the drill pipe or outer casing, sending the high frequency vibrations down through the drill steel to the face of the drill bit. This creates displacement, fracturing or shearing action depending on the material being drilled. The oscillator uses two eccentric, counter-rotating balance weights or rollers that are timed to direct 100% of the vibration at 0 degrees and 180 degrees. An air spring houses the oscillators and separates the vibration from the drill rig itself. The vibratory frequency is controlled to suit operating conditions and to achieve optimum drilling rates.When the vibrations coincide with the natural resonant frequency of the steel drill rod or casing, a natural phenomenon called “resonance” occurs. It allows the rig to transfer timed vibratory energy into the top of the drill string, utilizing the natural stored energy of the steel. This causes the drill string to use inertia and act like a flywheel delivering tremendous amounts of energy directly to the bit face. In friendly overburden formations, a sonic drill rig can achieve penetration rates of one ft per second."

Jan 1, 2008

By Benjamin Jennings, Jason Herron

In the summer of 2016 Xcel Energy experienced a storm event that resulted in the collapse of approximately 8.5 miles of a 345 KV transmission line near Rogers, Minnesota. In design of the new transmission line, Xcel Energy determined that ten tower locations would be replaced with steel H-frame structures supported by helical piles instead of wood H-frame structures supported by driven wooden piles. A steel foundation was proposed for the towers due to time constraints and site conditions unfavorable to large pile driving equipment. Xcel Energy contacted the helical pile manufacturer Hubbell Power Systems, Inc. (HPS) for aid in the design of a complete steel foundation for the structure legs. With the shear, moment, and axial loads provided, the manufacturer used pile group modeling and axial capacity software to design a four helical pile group; and used 3D modeling and finite element software to design a moment resistant grillage to connect to the tower base. The steel grillage utilizes a new moment resistant connection and clamp system to transfer loads from the piles to the grillage. This connection provides a true fixed head condition and reduces lateral deflection issues typical to smaller diameter piles in pinned head connections. The clamp is designed to deform the helical pipe pile shaft and transfer the full axial load of the structure through the mechanical and friction connection. The helical piles and the moment resistant grillage were manufactured with shorter than average lead times and a helical pile installation contractor performed the installation. An expedient plan of install was developed by the contractor that resulted in an average installation rate of one complete set of tower foundations per day. The design of the moment resistant grillage, clamping system, and excellent foundation construction by the contractor provided an expedient and efficient foundation system to be discussed in this paper.

Jan 1, 2017

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By Rich A. Lamb, Paul J. Axtell, Michael K. Muchard

"Since 2010, the Minnesota Department of Transportation (MnDOT) has performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. All of the piles were 42-in diameter, open-ended pipes driven to practical refusal on sedimentary bedrock with D125-32 diesel hammers from three separate manufacturers. The rapid load test method in general accordance with ASTM D7383-10 (Statnamic method) was used along with high-strain dynamic testing and subsequent signal matching. Results of these tests indicate that the axial nominal resistance of these piles in compression is not controlled by geotechnical considerations when driven with an appropriately sized hammer and installation criterion. Rather, the predominantly elastic load-deflection behavior of the piles under compressive load suggests the axial nominal compressive resistance is controlled by the structural capacity of the pile. In all instances, the rapid load tests indicated a nominal resistance exceeding that produced by high-strain dynamic tests due to insufficient hammer energy to fully mobilize resistance. In all cases, the hammers used were able to easily install the piles through the soil overburden. Mobilizing a larger hammer simply to demonstrate high-strain dynamic resistance is not economical or practical. This paper presents the subsurface conditions at each location, the ensuing test results, and the ramifications for future projects in Minnesota utilizing large-diameter open-ended pipe piles.INTRODUCTIONThe Minnesota Department of Transportation (MnDOT) has recently performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. The four project locations described in this paper where pile load testing was performed are shown in Figure 1 and exist in the southeastern portion of Minnesota. The projects are all major bridges crossing the Mississippi River in three instances and the St. Croix River just above the Mississippi River in the other instance. The first project is the TH 61 Mississippi River crossing in Hasting, MN where two load tests were conducted. The second is the TH 36 St. Croix River crossing in Stillwater, MN where two load tests were performed. The third project is the I-90 Mississippi River crossing in Dresbach, MN where three load tests were conducted. The final project is the TH 43 Mississippi River crossing in Winona, MN where one load test was performed."

Jan 1, 2017

By Christopher Sammon, Nicholas Turus

"The demand for underground parking in South Florida has increased as a result of changes to the local building code, coupled with developers’ desire to improve building aesthetics and provide much needed walk in retail space for high-end structures. Historically, underground construction was uncommon in South Florida due to the high groundwater level and porous soil/rock. Conventional dewatering methods become ineffective only a short depth below the ground surface and deeper excavations have required a tremie seal solution consisting of wet excavation and the pouring a temporary unreinforced slab under a water head. However, as excavation area and depth increase, the cost and schedule of the tremie seal method become problematic. For these reasons developers and construction teams alike have looked to contractors in South Florida for alternative means of construction.This paper details the construction of two sites in South Florida where Deep Soil Mixing (DSM) technology offered an efficient alternative to tremie seal construction. The Brickell City Centre required excavation of 8 acres to depths of 30 feet, and augercast piles up to 36” diameter and 110 feet in depth. The second site, Jade Signature, required an excavation of up to 41 feet directly adjacent to the Atlantic beachfront. Due to the concerns over differential settlement, the project featured a soil mixed gravity wall that was designed and installed to allow for completion of the tower prior to excavating the adjacent garage.Both projects involved improving every square inch of ground beneath the planned project excavation. The developed DSM seal slab solution creates a nearly impervious excavation at excavation invert with the strength to resist hydrostatic uplift forces. Low permeability site perimeter walls are constructed to complete the sealed excavation and reinforced with either beams or sheet piles for structural support. Augercast piles required for the permanent hydrostatic concrete slab supplement the uplift capacity of the DSM. After DSM and augercast piles are installed from grade, the site is excavated in dry conditions."

Jan 1, 2017

By N. Schmitz

This paper explains how new digital solutions improve reverse circulation drilling operations. Upgrading field-proven reverse circulation drilling (RCD) rigs with new digital technologies enables semiautomated drilling, with upgrade options for fully automated & remote drilling. Key elements of the improvements are electrically controlled valve systems, process instrumentations, a state of the art machine controller and drilling operation via a touch control panel. Automation of core processes, such as adding drill pipes, reduces set-up times, increases machine uptime for drilling and as a result efficiency. While drilling, sensors provide continuous feedback, which is used to automatically adjust e.g. the weight on bit to the optimum; resulting in an increased rate of penetration and less wear and tear. While in the past hydraulic power packs (HPU) have typically been operated at a constant high-performance level with related high fuel consumption, a new interface between the machine controller and the power unit regulates the HPU performance exactly according to the actual drilling operation needs. This leads to significant fuel consumption reduction. The safety benefits of the digital improvements are the ability to remotely operate the rig in challenging site conditions via a mobile operator panel.

Sep 8, 2021

By Mark Zablocki, Dakarai McCoy

Ground vibrations are an unavoidable effect of driving piles and may pose a risk to nearby infrastructure and the comfort of adjacent occupants. Driven-pile-induced ground vibrations are known to vary widely based on ground conditions, pile material, and installation means and methods. A monitoring sensor to record ground vibrations during pile driving is necessary for understanding potential impacts to sensitive infrastructure and should be considered when implementing a monitoring program anticipating ground vibrations. The implementation of a vibration monitoring program historically relies on experiential-based decision-making, which may result in the costly vibration monitoring of low-risk infrastructure. Prior understanding of anticipated ground vibrations is necessary to create an appropriate monitoring program. A framework is proposed for organizing data from past monitoring programs and quantifying the anticipated risk of driven-pile-induced vibrations. An example of risk quantification from data imported to ]a cloud database is presented by comparing driven steel H-pile and prestressed precast concrete vibration monitoring measured and collected by Haley & Aldrich between 2010 and 2020. The methods presented within the example can be applied to quantify a first order approximation of risk for ground vibrations at proposed driven pile sites based on the measured performance of previous sites with similar ground characteristics and pile installation methods. The presented novel data managements tools allow for a quick aggregation of vibration data with similar site conditions.

Sep 8, 2021

By Francisco A. Flores, Rigoberto Torres

The Complementary Technical Standards of Mexico’s City Building Code do not mention the criteria to compute the bearing capacity of Steel H-piles. It is necessary to increase knowledge in using steel H-piles as foundation elements in very soft soils of Mexico City. Considering their applicability to reinforce structures as well as new foundations in confined spaces, this research is proposed to obtain the axial load capacity of piles at scale in laboratory. This paper describes the construction and testing of scale models in laboratory of steel H-piles to measure their axial compression and tension load capacity in the soft soils of Mexico City. Three types of piles were fabricated at scale. Tests were performed on individual piles and pile groups. Based on the axial load tests, the load-displacement curves are presented both in compression and tension. The analysis of the results is shown, and comments are given regarding the ultimate bearing capacity of piles. Recommendations are presented regarding the determination of the bearing capacity of these piles in the very soft soils of Mexico City.

Sep 8, 2021

By James P. Chivilo, Gregory R. Meeder, Scott J. DiFiore, Matthew H. Johnson

New construction in metropolitan areas has direct impacts on immediate neighbors and abutters. While noise and dust are generally nuisance concerns, demolition, vibrations, excavation, and dewatering can cause structural damage to adjacent structures. Different cities, states, or jurisdictions have different regulations that dictate requirements, roles, or responsibilities for varying parties during construction. The authors will introduce and discuss risks of new construction adjacent to existing structures, and the legal framework in Illinois which requires the owner of the new construction project to provide adequate protections for adjacent existing structures. The authors, who are engineers and attorneys, will discuss technical and legal concerns, and will highlight the importance of early and frequent communication among project participants to manage risks, despite whether or not any local regulations exist to drive the process. RISKS IN ADJACENT CONSTRUCTION New construction in metropolitan areas inherently involves some combination of noise, dust, ground-borne vibrations, earth excavation, and subgrade dewatering. These issues have potential to directly and adversely affect abutters and their property. Noise and dust can be nuisance concerns, while vibrations, excavation, and dewatering can result in damage to abutters’ structures. Noise and dust are unlikely to lead to physical damage to abutters’ property, and can be controlled with limited work hours and good housekeeping practices. Vibrations and excavations, however, if not well understood, planned for, and mitigated, can result in serious damage to abutters’ structures. In turn, this damage introduces additional and often significant costs and schedule delays.

Jan 1, 2019

By Andrew R. Klaetsch, Peter W. Deming

"The Washington Avenue tunnel in Kingston, NY was completed in 1912 to convey combined storm water and sanitary sewage. Over a mile in length, the tunnel was driven almost entirely in bedrock, with the exception of an approximately 170 foot long brick arch segment constructed in soil. About 90 years after the tunnel was put into service, persistent subsidence problems and sinkholes were observed in Washington Avenue above the shield-driven soil tunnel segment, eventually causing the important traffic thoroughfare to be closed. Subsequent tunnel inspections revealed a breach in the brick arch and a significant volume of fine soil within the tunnel. A two-phase remediation program was implemented to control seepage, reduce soil migration, and remedy sinkhole problems. The first phase included in-situ soil densification by vibratory pile probe driving to improve density in shallow sandy soil loosened by ground loss. The second phase included installation of a continuous soilcrete arch structure over and alongside the tunnel, extending to rock or compact glacial till and spanning the length of the soil tunnel segment. Overlapping vertical soilcrete columns were installed through interlayered sandy and clayey silt by jet grouting to form a continuous arch structure, using grout parameters verified by full scale field testing.PROJECT BACKGROUNDThe Washington Avenue tunnel in Kingston, NY (Figure 1) was completed in 1912 to convey combined storm water and sanitary sewage to Rondout Creek by the Board of Water Supply of the City of New York. The tunnel is over a mile in length and constructed primarily in rock. Contract documents indicate the tunnel was designed with a horseshoe shape at least 3 ft wide and 5.5 ft high."

Jan 1, 2016

By Marwa Nabil, Alaa A. Ata

"Recent developments in the analysis of piled rafts has incorporated the load sharing of the raft and the piles to support the superstructure. In the piled-raft system, piles are cast monolithically with the raft and the load is partly transmitted by the raft to the soil directly below it, and partly by the piles to more competent deep soil. While these piles are effective in increasing the bearing capacity and reducing the settlements, they often lead to significant straining actions at the pile head-raft connection which may constitute the weakest link. An attempt to provide a more economical solution, that at the same time overcomes this weak link, is to disconnect the pile heads from the raft and introduce an intermediate cushion of compacted fill. In this case, the piles are considered as reinforcement to the subsoil and will also act as settlement reducers. This paper investigates the load transfers mechanism of the unconnected piled raft with cushion using ABAQUS finite elements Program. The main objective is to provide an in depth analysis of the raft–soil–pile interactions in multi-layered soil under static and seismic loads. The investigated system provides an economical alternative for traditional connected piled raft foundation, where there is no need to reinforce the piles, no need for pile head demolition or expensive waterproofing of the pile head connection. Cost analyses of unconnected versus connected piled raft systems confirmed a cost savings in the construction that may reach from 50 to 70 percent.INTRODUCTIONDesigners around the world have gained more confidence to use the piled-raft as a more realistic system where the raft and the piles share transferring the superstructure loads to shallow and deep soil layers. A further advancement is to use unconnected piled rafts as another practical and economical alternative to the traditional piled rafts. Unconnected piled raft is also synonymous to settlement reducing piles; or simply, soil improvement piles. Liang et al. (2003) has extended the concept of pile-raft-foundation to a new type of foundation called composite piled raft foundation or unconnected piled raft foundation. The foundation is composed of a sand/gravel cushion sandwiched between the raft and piles. The piles group may contain short and long piles. The short piles are constructed of flexible materials such as soil-cement columns or sand-gravel columns, and are used mainly to improve the bearing capacity of shallow soft soil; the long piles, which are made of relatively rigid materials such as concrete, and their main function is to reduce settlements. The cushion plays an important role in mobilizing the bearing capacity of the subsoil and in modifying the load transfer mechanism of the piles. In Shanghai, China, this system of unconnected piled raft has proved to be quite suitable and effective in coastal areas, where deep soft soil deposits exist."

Jan 1, 2016

By Hugo Meggitt, Damian R. Siebert, Wystan Carswell

Excavation-induced ground movements are a critical component in the design and construction of deep excavations in urban settings due to the potential adverse effects on adjacent structures and infrastructure. Ground movements are influenced by soil stratigraphy, soil properties, adjacent structures, and construction means and methods. The use of empirical relationships, computer models, and reliance on experience with similar excavations in similar soil conditions often provides a basis for predicting excavation-induced ground movements. In this paper, data from 21 deep excavations approximately 20 ft to 75 ft deep supported by concrete diaphragm “slurry” walls in the Greater Boston area are compared to published literature, considering how different foundation systems (e.g. shallow foundations, caissons, and piles) of abutting structures have been affected by adjacent excavations. The influence of construction method (conventional vs. top-down) on adjacent foundation movements indicate that top-down construction typically results in smaller foundation movements. INTRODUCTION Estimation of ground movements due to excavation is a challenging endeavor, even with complex three- dimensional finite element modeling and high-order constitutive models that are increasingly available in modern engineering practice. Aside from the expense of the soil exploration and testing used to inform these higher-order models, the challenges of modeling past stress history, adjacent structures, and the groundwater conditions during excavation require not only large investments of time during design but also validation from past experience (to avoid a “garbage in, garbage out” paradigm). While site conditions such as soil stratigraphy, soil properties, groundwater conditions, and as-built conditions of adjacent structures can be obtained, measured, and estimated, the effects that means and methods of construction have on ground movements are difficult to quantify. During early phase design, assessments of predicted ground movement are unable to account for all aspects of project construction, nor is it cost-efficient to fully design an excavation while project parameters such as site size and excavation depth are under consideration by the design team. While construction is in progress, benchmarking support of excavation performance and associated ground movements in the context of successfully completed projects allows for a more nuanced view of system performance and provides the opportunity for more informed decision-making (if required) as construction proceeds. For these reasons, the use of empirical relationships and the collection of historical support of excavation performance holds high value for the practicing geotechnical engineer at all phases of the project.

Jan 1, 2019