Search Documents

By Nathan A. Ingraffea

The use of steel sheet pile walls and drilled shaft foundation elements to enable up-down construction methods has been used successfully on recent high-rise structures with multi-story below grade parking. The John Ross Tower and The 3720 Tower in Portland, Oregon each make use of this system and are discussed in-depth. Up-Down construction involves the simultaneous construction of the building levels above and below grade instead of the standard construction technique of excavating and shoring the below grade construction before being able to build upward from the base of the excavation. Advantages of the up-down system include a shortened overall construction schedule, permanent basement walls that double as the temporary shoring walls, elimination of the typical continuous wall footing or grade beam at the building perimeter, increased use of recycled material (steel) while maintaining an overall decrease in total materials, elimination of wall forming costs, decreases in forming costs for slabs, decreases in waterproofing costs for walls and elimination of pile caps and/or footings for the building columns. Lessons learned during the construction of both buildings include the need for more extensive geotechnical boring information, descriptive sheet pile and drilled shaft specifications, a clear understanding from the design team on finished appearance of sheet pile and shafts, and careful consideration of the connection between both slabs and the sheet pile wall and slabs and drilled shafts.

Jan 1, 2008

By Jennifer Peirce Brandt

Project documents and the United States Army Corps of Engineers? permit for construction of the Stemmers Run Relief Wastewater Force Main across the Back River in Baltimore County, Maryland specified a minimal width, steel sheet pile cofferdam and a 12 feet wide, pile supported, timber decked, causeway trestle ? both approximately 1700 feet in length. Due to the impractical width of the causeway, the contractor desired to combine the cofferdam and the causeway structures in order to minimize wetland disturbance and maximize access for construction equipment. The resulting support structure was a steel sheet pile cofferdam, approximately 17 feet wide, internally braced, and capped with transverse timber deck mats to serve as the access and work trestle for the trench excavation, pipe bent construction, and trench backfill. Construction of this cofferdam/causeway progressed from the north shoreline toward the middle of the river. Then, working back toward the north shoreline, the contractor excavated, installed the 54 inch diameter pipe and H-pile support bents, and backfilled the trench in increments of approximately 60 linear feet. Excavation spoils from one section were used to backfill the preceding section. As the pipe installation progressed toward the north shore, the steel sheet piling and timber deck were removed. As sufficient sheet piling and deck mats were removed, the contractor began the process anew from the opposite shoreline using the reclaimed materials. The project was complicated by the presence of deep, very soft, weight of hammer, silts and organic clays and an unbalanced, hydrostatic head of 20.5 feet. In addition, concurrent pile driving, excavating, and backfilling in successive cofferdam sections required the use of heavy, long reach, hydraulic backhoes, and a 200 ton capacity crawler crane which controlled the design of the timber causeway deck and its supporting sheet piles.

Jan 1, 2008

By Douglas Heenan

The fracture orientations were inferred based on theory and previous experience. The fracture pattern was not monitored during the project. Grout volume was recorded at each sleeve port and real time movement monitoring of the building foundation was performed.

Feb 10, 2003

By Masaki Kitazume

Five papers were presented orally to the topics of Jet Grouting and Deep Mixing. The session was started with a brief introduction by the moderators. Following the oral presentation, floor discussions were directed by the moderators. A brief introduction of each of the oral presentations is provided before each discussion.

Feb 10, 2003

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By Dempsey S. Thieman

The Kuparuk River Central Channel Bridge on the North Slope of Alaska provides critical access for oilfield service vehicles in the largest oilfield in the United States. The original sloped spill-through bridge abutments were protected by articulated concrete revetment. After 27 years of heavy service, ice impact, deep river scour, and high floods, the revetment required replacement. An OPEN CELL SHEET PILE® abutment was selected to replace the existing erosion protection and provide increased performance and structure life. Project engineers and contractors successfully addressed the challenges of low overhead sheet pile installation under the bridge, extremely heavy vehicle loads, and arctic winter construction conditions through innovative design and construction techniques. The project was successfully completed on schedule with minimal disruptions to critical bridge traffic. This paper provides a detailed discussion of the design and construction techniques utilized to address the challenges of the project, many of which could be adapted to other projects.

Jan 1, 2008

By Douglas L. Scaggs

Driving piles in under water applications has become more common place over the past twenty years. Where only a water depth reachable with a follower or dewatered cofferdam was the rule in the past, newer technologies developed for the offshore oil and gas industry have made depths of even several thousand feet possible offering new possibilities in foundation design and installation. With the new technology, engineers can now more efficiently design structures by placing foundations optimally thereby reducing weight and cost of the overall structure.

Jan 1, 2013

By Edwin W. Hickey

This paper briefly discusses the geologic conditions in South Florida relative to the design, construction, and performance of deep foundations. The subsurface conditions in this area are unique in that the rock layers are highly porous and often very soft, and are sandwiched between layers of typically loose, uncemented quartz fine sands. Due to the high porosity of the Miami Limestone, 4-inch diameter rock coring is often required to obtain intact samples, and dewatering of excavations is sometimes difficult or impossible. The sand layers, typically tens of feet thick, are very loose to loose in relative density and have been the cause of unexpected large, deep foundation settlements. The engineering properties of the various geologic formations are discussed, along with typical deep foundation types used in the Miami area prior to and after 1980.

Jan 1, 2003

By K. Fujita

In order to deal properly with the fundamental aspects of pile construction, the following problems and their solutions are introduced: For driven piles - stresses, damage, movements of surroundings, compaction of ground, deviation of pile direction and location, selection of pile hammers and penetrability of piles are important factors. For drilled piles -loosening of the ground, supports for boreholes, minimizing ground loosening and defects are critical items. Attention should be given to changing soil characteristics. Also, supervision by experienced engineers and good workmanship by skilled laborers are recommended to ensure the quality of the piles.

Jan 1, 2010

By Artak D. Mirzoyan

Pile foundations near the edge of a slope are often required to resist lateral loads. This is particularly important for piles at abutments of bridges. However, very few full-scale tests are available that compare the effect on lateral resistance of piles installed in sloping ground to piles installed in horizontal ground. To investigate the effect of a slope on lateral pile resistance, three full-scale lateral load tests were performed on an instrumented steel pipe pile. For the first test, the pile was laterally loaded in horizontal ground; in the second test, the pile was at the crest of a 30º downward slope; and for the third test, the pile was located three pile diameters from the crest of a 30º slope. The soil around the pile consisted of well-graded clean sand (concrete sand) and was compacted to 95% of the modified Proctor maximum unit weight in all three tests. Lab and in-situ direct shear tests indicated that the friction angle of the sand was approximately 39 degrees. The pile was instrumented with strain gauges so that the bending moment versus depth profile could be determined. Pile head load, deflection and rotation were also measured. Based on the load versus deflection curves, the presence of the slope resulted in a decrease in lateral resistance of about 20% for the pile at the crest of the slope and 8% for the pile at 3D from the crest of the slope relative to the pile in horizontal ground. The presence of the slope also resulted in an increase in the maximum moment of 29% and 20% for the piles at the slope crest and at 3 pile diameters from slope crest, respectively. Analyses using LPILE with the measured friction angle significantly underestimated the lateral resistance for the horizontal soil profile. After calibrating the model with the response of the pile in horizontal sand, analyses including the slope still underestimated lateral resistance by about 20%.

Jan 1, 2007

By Clifford J. Wren

A geotechnical foundation solution was required to halt and prevent further structural distress suffered by a residential four storey apartment building in Hamilton, Scotland. Residents of the ten year old building started to notice cracking and signs of distress approximately one year after moving into the property. A detailed intrusive inspection of the structure revealed that the building was moving and had suffered significant settlement and structural distress at the shared party wall between it and an adjoining building. Roger Bullivant Limited (RBL) was appointed Principal Contractor to carry out an agreed remedial works contract which included a complete structural ?strip-out? of the ground floor, underpinning, contiguous bored pile retaining wall and reinstatement. The paper describes how a proprietary pile and needle beam underpinning system was used to prevent further differential movement and provide a new secure foundation for the residential building. The case study illustrates how a flexible problem solving approach can be applied to a difficult and sensitive geotechnical project.

Jan 1, 2008

By Matthew C. Pierson

Due to space limitations for transportation projects, many times sound walls must be constructed above mechanically stabilized earth (MSE) walls. These sound walls must resist lateral loads from wind or impact and must therefore be constructed on drilled shafts passing through the reinforced fill for the MSE Wall. Current design methods for the drilled shafts are believed to be overly conservative. Full scale lateral load testing of three foot diameter shafts contained within and solely supported by a 20 foot tall MSE block wall was conducted and the lateral capacity was evaluated. Shafts were tested individually and as a group. The data collected from full scale testing was then used to calibrate numerical models. This paper contains a discussion of how the facing type and stiffness affects the behavior of the numerical model as well as selected comparisons between the actual test data and selected model simulation results.

Jan 1, 2009

By Sam Messina

[Project: Job Number: Date: Superintendent: Person Making Inspection: Note: The following checklist shall be used on a regular basis as an overall assessment of the jobsite. The checklist is not all-inclusive. All applicable Federal, State, and local regulations, standards, and ordinances pertinent to the jobsite conditions must be evaluated on a continuous basis. Column A - Adequate Column I ? Inadequate]

Jan 1, 1998

By Darrell L. Beddard

The test program information provided for some immediate changes on the upcoming contracts and in contract administration for the I-880 Replacement Project. Plan sheet modifications included changes to the pile data tables showing the actual demand load required for structural stability. The normal class of pile with a minimum load carrying capacity was removed. This provided for substantial pile length reduction at several locations since the structural loading was much less than the predetermined pile class ultimate capacity. New specifications were developed and standard specifications were modified to accommodate the newer foundations, installation procedures and pile acceptance criteria. Current Caltrans specifications require that the Contractor provide bearing capacity at the specified tip elevation. This requirement was removed and pile acceptance was determined by the Engineer. Acceptance criteria was established by the State and was based on. set-up trend over time. Static loading tests were reduced especially in areas where testing was performed on the indicator program. Testing procedures were modified and set-up periods were established before piles could be tested. For the contract near the San Francisco Oakland Bay Bridge (Unit E) the FHWA 1000 tons (8.9 MN) test beam configuration was completely changed. This provided added safety and allowed more tolerance in the pile placement for the testing operations. Indicator piles were added as companion piles to the static loading test piles. These piles were used for restrike events which included collecting dynamic data for calibrating the wave equation analysis with static load test results. Indicator piles also provided quick access for restrike events, where as, the static loading test pile needed modification to perform the restrike operation. Penetration rates were recorded for these operations. Wave equation Analysis Program (WEAP) was used in developing the acceptance criteria. The standard Engineering News Record (ENR) formula in the current Caltrans' Standard Specifications was removed for the contracts. Contractors were required to submit, prior to driving piles, a driveability study for their contract. These studies required discussion of their operations, method of installation, effects of soil set-up, set periods, hammer settings, bearing graphs, inputs to the WEAP program and complete a "Pile and Driving Equipment Data" form. Dynamic monitoring was detailed in the specifications on how the monitoring process was to occur. Set periods were established and restrike events were called out with the frequency of these events.

Jan 1, 1996

By Jorj Osterberg

550 load tests of up to 150 MN have been completed on driven and bored piles using the Osterberg Load Cell. Because the test measures side shear and end bearing separately, much can be learned about the forces on the pile as it is loaded to ultimate capacity. At working loads side shear almost always far exceeds end bearing, with the distribution of shear and bearing greatly affected by disturbance occurring during drilling operations. Since much less movement is required to mobilize side shear than end bearing, most of the bearing develops after the working load is exceeded. Thus with insufficient bottom cleaning, safety against excessive settlement can be considerably reduced. Improved methods of drilling, hole cleaning, rebar cage installation and concrete placement are discussed. For rock socket piles it has been found that the ultimate test load far exceeds the working loads in most cases. This is almost always due to greater penetration into the rock than is required for adequate safety against excessive settlement. Factors affecting rock socket capacity are discussed. Increase of side shear and ultimate capacity with time is discussed. Case histories for driven and bored piles in soil and rock sockets are described.

Jan 1, 2001

By Mitsuhiro Shibazaki

Generally, water-soluble polymers are effective in convergence of water jet ejected from a nozzle as they add viscosity to water. However, excessive additional polymers (added to keep water viscous) could increase friction on the contrary. Therefore, we have totally modified the jetting system from every possible aspect, such as the shape and upstream conditions of a nozzle in order to keep the flow spread to the minimum as stated in my presentation.

Feb 10, 2003

By Helen Ahnberg

The scope of the present paper is limited to report the experimental evidence and not for describing the analytical assumptions. However, the idea behind the experimental program is that the deterioration may be caused by the leaching of Ca from the treated soil to surrounding soil or water driven by the difference in the Ca ion concentration. As a consequence of Ca leaching, it may be natural to expect the expansion of micro void space within the treated soil. In a saturated condition, the water inflow into the treated soil may accompany the leaching phenomenon. We measured the water content within the treated soil. But there is not much difference in water content within the soil.

Feb 10, 2003

By Terence P. Holman

Instrumented load testing of high capacity micropiles, followed by detailed analysis and numerical modeling, provided an opportunity for real foundation performance to be incorporated into the design of a complex urban high-rise structure. This paper discusses a design-based load testing program and subsequent analysis for micropiles incorporated into a piled raft foundation beneath a portion of a high-rise residential structure in Brooklyn, New York. Preliminary numerical analysis, performed using the commercial finite element package PLAXIS 3D Foundation, indicated that soil stiffening and transferring heavy core loads to greater depths was required to minimize the total and differential settlements. High capacity micropiles were modeled below the tower core mat to create a piled raft effect, reducing the settlements to acceptable levels. Final design of the foundation and micropiles, and final numerical analysis of the proposed foundation system required an instrumented load testing program to provide the Owner and design team with a level of comfort. The instrumented load test provided data on the evolution of load transfer, including the mobilization of significant tip resistance, frequently ignored in design, and micropile axial stiffness. Final numerical analysis of the foundation system involved refining the PLAXIS model based on the micropile behavior and load transfer mechanism observed during the load test program. The authors believe that the combination of design-based load testing and numerical analysis in this project yielded a more refined foundation system with realistic expectations of performance.

Jan 1, 2007

By Dennis Nottingham

Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971 L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers' experiments, observations and measurements, led to an "H" pile probe design which has produced measured soil density improvements up to 250% using SPT "N60" values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern "Open Cell" bulkhead projects will be presented and discussed.

Jan 1, 2004

By Lawrence Piccagli

This past spring of 2006, BENCOR installed the concrete reinforced diaphragm walls for the COSMOPOLITAN RESORT & CASINO in Las Vegas, Nevada. The project highlights include the excavation of approx. 326.000 square feet of reinforced diaphragm slurry wall with a thickness of 30 inches and a depth of 100 feet using three reverse circulation trench cutters (hydromills) at the same time. The reinforcing steel cages were fabricated on the 8 acre jobsite and approximately 12,000 cubic yards of 4500 psi concrete was placed via tremie. The jobsite logistics of coordinating three trench cutters and three separate desanding/slurry plants as well as the reinforcing steel fabrication and concrete placement all under a very tight schedule was quite challenging. A second main exercise was the execution of a temporary excavation support. As the excavation depths extends between 66 and 72 feet, five to six rows of temporary tieback anchors were required. Anchor lengths range from 43 -83 feet at a maximum design load of 235 kips.

Jan 1, 2007