Search Documents

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By J. W. Wang

This article first explains the mechanism of forming strength in the Jet grouting reinforced foundation, and points out the function of cement hydrates and clay minerals in clayey soil, the reinforced body with the character of long-term growth of strength. Secondly, regarding the strength and the deformation characteristics of compound foundation, the article points out that the stress-strain curve of the jet grouting pile is approximate to hyperbolic curve. Finally, the article cites three examples of application in the construction of the metallurgical industry.

Jan 1, 2010

By James S. Graham

Specifications for treated round wood piling are presented for the engineers consideration. Included in the text are background information, technical committees, Chellis, quality, treatment, static and dynamic stresses, accessories, and existing codes and standards. The specifications are also available using Word Perfect on 3.5 or 5.25 inch size disks provided by the National Timber Piling Council. Note: DFI recommended wording is wood, head, and toe, instead of timber, butt, and tip.

Jan 1, 1992

By Douglas W. Christie

Deep foundations in Washington, DC have played a role in the city?s development since the 19th century. Designers of government and commercial buildings sought deep foundations initially to minimize settlement of structures. As the western portion of the National Mall was made by filling in portions of the Potomac River, numerous memorials and monuments on the Mall required deep foundations. In recent years deep foundations have been used to allow underground construction for various reasons. Commercial developers have sought to maximize the use of sites by developing below-grade space for parking to meet code requirements and offset the limits on building heights. Underground museum and gallery space has been constructed to expand public space while preserving open space above grade. Access and security concerns have prompted the design of underground visitor centers rather than above-grade structures.

Jan 1, 2006

By B. B. Broms

The high transverse tensile stresses that develop in precast concrete piles during driving have been investigated experimentally from pile load tests and theoretically using the finite element method (FEM). These tensile stresses can be high enough to cause longitudinal splitting of the piles just below the pile cap. Test data and FEM indicated that the maximum transverse tensile stress will increase with increasing thickness of the cover. The maximum tensile stress can be high especially if the pile is eccentrically loaded. The results from the experimental investigation and from FEM are described in the paper as well as a simplified method based on the stress distribution in a concrete cylinder at an indirect tension test.

Jan 1, 2010

By Martin Pratt

This paper is an overview of deep foundation engineering in Hong Kong past, present and future. The enormity of the subject compared with the space available makes brevity inevitable. Issues of construction and design are covered and some examples of recent challenging projects are given. The content is aimed at those with an interest in foundations generally, but with limited knowledge of the Hong Kong scene. Reference is made to informative publications for further reading on specific topics.

Jan 1, 2000

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By George K. Burke

Jet grouting was first introduced into North America in the late 1970's, soon after the conception of the system in Japan. However, it was not until the mid-1980's that the technique began to gain acceptance through the renewed interest and efforts of specialist U.S. geotechnical contractors. Since this time, innovations by both American users and other users worldwide have further advanced the technology, with a corresponding increase in the range of practical applications. This paper discusses the evolution of jet grouting in North America, from simple single-fluid methods to more complex triple-fluid methods, to the energy-intensive double-fluid and SuperJet methods. Case histories, illustrating a variety of jet grouting methods and applications, are cited to support the newest United States applications.

Jan 1, 2002

By P. J. Yttrup

Small diameter timber piles are used in Australia to solve foundation problems in soft or filled ground and expansive soil. The paper describes the results of pile load tests to develop simple methods for bearing capacity determination and observation of the performance of piles in expansive soil.

Jan 1, 1989

By R. A. Bullivant

Roger Bullivant Piling Limited has started 1992 with the introduction of the CONE PILE into its range of precast concrete foundation techniques. Since the establishment of its Piling Division ten years ago, alongside the original Underpinning Company, a commitment to innovated development has seen a steady growth in Roger Bullivant's activity in piling, ground treatment and general foundation engineering. Over the last four years, £1.2 million has been invested by the Bullivant Piling Division into research and development in the field of precast piling and other foundation systems. The goal has been to develop economically attractive systems tailored to our clients design requirements and, wherever possible, unique to Roger Bullivant Piling.

Jan 1, 1992

By Lewis Stansfield

A rotary displacement method was used to install permanent steel casings for bored piles through an asbestos tip. This method was chosen in preference to alternative driven systems because it was quieter and more versatile if obstructions were encountered. New equipment was designed and made specifically for the project, and stringent health and safety regulations had to be observed.

Jan 1, 2000

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

By Han Xuanjiang

Through whole analysis of static testing piles information of a teaching building, this paper put for ward that when the ratioes of unload rebound amount to residual deformation and to total settlement reach the maximum, the testing load is selected as allowable capacity of single pile by camparing with the settlement in the practical engineering, it is proved that this method fits to practice, for other several projects, its also available. Therefore non-destructive testing pile method was improved, so all the tested piles can be reused as engineering piles.

Jan 1, 1991

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995

By Juan J. Campo

The Freeport-McMoRan Main Pass Mine development in the Gulf of Mexico is a complex designed to extract up to 67 million long tons of sulphur over a 40 year period. The initial development includes 15 platforms and 13 bridges located in water depths ranging from 208 to 214 feet, approximately 15 miles east of the Mississippi River Delta. Three additional platforms were designed and installed for the oil and gas development in the complex. Over 110, 000 short tons of steel were required to fabricate the structures. As the sulphur is extracted significant subsidence is predicted over a major portion of complex in the shape of a very large bowl. Vertical elevations are predicted to change as much as 65 feet. Horizontal movements and mudline slope changes cause adjacent platform decks to move as much as 30 feet relative to each other. Differential soil movement is predicted between piling of individual platforms causing the piling to spread, resulting in significant lateral loading on the piling. Relative vertical soil movements are predicted along the lengths of the piles which causes "up drag" or "down drag" forces on individual piles. This paper addresses the design of the piling for the structures in the complex. Design criteria will be discussed explaining how the more traditional offshore environmental and gravity loadings were combined with the unique loading caused by subsidence. Design and analysis procedures will be explained and analysis results presented. These results include the incorporation of 100 ksi steel in thicknesses up to 5 inches in some of the tubular piles. Comparisons will be made between conventional offshore structures and these structures designed to accommodate the subsidence.

Jan 1, 1992

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960's. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000

By Shinji Sassa, Naoki Takahashi, Eiji Kohama, Wakaki Tsuda, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"Abstract Deep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. Column-type solidification, however, has been thought to have little effect as a liquefaction countermeasure, because the shear deformation of unimproved soil between the columns cannot be reduced. In recent years, experimental results have been reported that imply that solidified columns can reduce the shear deformation of unimproved soil around them. A new arrangement has been proposed to mitigate lateral flow induced by liquefaction. In this study, a series of dynamic centrifuge model tests was conducted to verify the lateral flow resistance of stabilized columns. The results indicate that stabilized columns can reduce the lateral flow of liquefied ground if the column displacement and the column head rotation are restricted. This paper concludes that it is important to restrict the displacement and the rotation of the column head by surface improvement to mitigate the lateral flow of liquefied ground.INTRODUCTIONDeep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. The solidified body formed by the deep mixing method is usually block or lattice shape, composed of solidified columns that overlap each other horizontally. Lattice-type solidification has been shown to be effective as a liquefaction countermeasure despite the presence of unimproved soil inside the lattice wall, because the shear deformation of the interior soil is restrained by the wall (Suzuki et al., 1989). On the other hand, it has been thought that column-type solidification cannot reduce shear deformation of unimproved soil around columns, because the displacement of a solidified column is less restricted than that of a lattice wall. Column-type solidification has been reported to have little effect as a liquefaction countermeasure, but to be superior in terms of construction cost and applicability around existing underground structures (Koga et al., 1986). However, there are experimental results implying that solidified columns have reduced the shear deformation of unimproved soil and mitigated its liquefaction (Yasuda et al., 2003; Tanaka et al., 2003). Yamamoto et al. (2006) conducted dynamic analyses of ground improved with lattice- and column-type solidification. Their results showed that column-type solidification with an improvement ratio of more than 35% reduces excess pore water pressure generated by earthquakes. Furthermore, the new column arrangement shown in Figure 1(a) has been proposed to mitigate lateral flow induced by liquefaction. It was developed and has been verified using dynamic model testing in a 1 g field (Takahashi et al., 2010a; 2010b; 2013; Towhata et al., 2010). The stabilized columns in this configuration interrupt lateral flow in any direction, unlike those placed in square and triangular arrangements."

Jan 1, 2014

This work shall consist of furnishing and driving foundation piles of the type and dimensions designated on the plans or in the special provisions including cutting off or building up foundation piles when required. This specification also covers providing test piles and performing loading tests. Piling shall conform to and be installed in accordance with these specifications, and at the location, and to the elevation, penetration and bearing capacity shown on the plans or as directed by the Engineer. Except when test piles are required, the Contractor shall furnish the piles in accordance with the dimensions shown on the plans or special provisions. When test piles are required, the pile lengths shown on the plans are for estimating purposes only and the actual lengths to be furnished for production piles will be determined by the Engineer after the test piles have been driven. The lengths given in the Engineer's order list will include only the lengths anticipated for use in the completed structure. The Contractor shall, with-out added compensation, increase the lengths shown or ordered to provide for fresh heading and for such additional length as may be necessary to suit his method of operation.

Jan 1, 1989