Search Documents

By Anupam Saxena

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading test, and installation of piles for a 22-story condominium tower in southwest Florida, U.S.A. ASC was commissioned to provide value engineering services in the proper selection of an economical and satisfactory foundation system. For the site-specific subsoil conditions, various types of foundations were considered and following an evaluation of high structural loads, site-specific constraints, and the production timeframe mandated by the project owner, a prestressed concrete pile-supported system was selected as an economical and effective foundation approach. The building foundations were designed for a compression capacity of 575 kN (65 tons) for the tower and 220 kN (25 tons) for the parking structure. The axial pile capacity and lengths were predicted using SPT91 software. The validation of these capacities was derived from driving 21 probe piles and performing static loading tests on selected probe piles (2 in compression and 1 in tension). The predicted pile capacities were evaluated with results from static loading tests on selected probe piles. This information was effectively utilized as part of an overall quality control program to install a total of over 920 prestressed concrete piles to lengths ranging from 11.5 to 16.5 m (37 to 54 ft) below existing ground elevation as part of the foundation support system.

Jan 1, 1996

By Henry Zhang

This paper presents two case studies of large diameter driven tubular steel piles for the ongoing Woolgoolga to Ballina Pacific Highway upgrade (W2B). This project forms part of Australia’s largest regional infrastructure project and will upgrade about 155 kilometers of highway to four-lane, divided road. There are more than 170 bridges on W2B, and driven tubular steel piles are adopted on 43 bridges between Glenugie and Ballina. Driven piles terminating in soil or basalt is a big challenge faced by both designers and piling contractors due to 1) the uncertainty of expected pile unit shaft and base resistance in different soils; 2) whether plugging is formed; and 3) highly variable basalt strength and thickness near top of the rock. If these risks are not adequately managed during design or construction stages, it could lead to unexpected project delay, extra time and cost or pile toe damage in basalt. This paper describes two case studies, one for piles designed to terminate in soils and the other for piles designed to terminate in basalt. How these risks were assessed and managed during detailed design, procurement, hammer selection, pile installation and verification will be discussed in details with lessons learnt summerised in the conclusion.

Nov 1, 2022

By A. Fisher

The use of thermal integrity testing to verify the quality of deep foundations has increased significantly in the UK and other world markets over the last 5 years. The introduction of distributed fibre optic sensing to this field has broadened the range of applications in which it can be deployed and the types of foundations which can be tested. This paper presents how fibre optic sensing technology can be successfully deployed in the construction environment the range of foundation techniques to which it can be applied. Alongside developments in the practical aspects of thermal testing, progress has been made in establishing assessment criteria which can be used to evaluate the results. This paper presents recent examples of comparative studies on foundations which include both thermal integrity testing, cross hole sonic logging and intrusive coring. The use of distributed strain measurement during pile load testing presents an alternative means to verify the assessment criteria used for integrity testing. This new approach can achieve comparable results to foundation exhumation or intrusive investigation and at a fraction of the cost. This paper presents the findings of several such studies, highlighting the benefits and opportunities for future improvement of the method.

Oct 1, 2022

By Emad Farouz, Ehab S. Shatnawi

"The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilledshaft diameters has motivated the development and increasing use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft capacity, especially for shafts tipped into loose cohesionless soils. Nevertheless, there remains considerable uncertainty in predicting the performance of base-grouted shafts, particularly for shafts tipped into cohesive soils. To date, there are only two documented design methods for estimating the axial geotechnical resistance of base-grouted shafts: Tip Capacity Multiplier (TCM) and Axial Capacity Multiplier (ACM) methods. A comprehensive test program was carried out during the design phase of the Wisconsin Zoo Interchange project to help optimize the flyover ramp’s foundation design. The test program included installing and testing one base grouted shaft and one ungrouted shaft at two sites with different ground conditions. Based on test results, it was concluded that prediction of the TCM method is well correlated with the measured values for both cohesive and granular soils; however, both methods tend to underestimate the axial resistance. Results also highlighted the importance of the base-grouting criteria in taking full advantage of the base grouting.INTRODUCTIONBase-grouted drilled shafts (BGDS), also known as post-grouted drilled shafts, consist of conventionally installed drilled shafts that contain access grout tubes placed within the shaft during construction. After installing the drilled shaft and achieving the pre-established concrete strength, grout is injected at the shaft tip through the access grout tubes to improve soil behavior around the drilled-shaft base. The tip grout injection improves the overall shaft capacity and reduces settlement through Densifying the in situ soils, compressing any debris left by the drilling process, preloading the soil beneath the tip to mobilize the shaft base resistance within service limits, increasing the tip area, and increasing the side resistance in the lower portion of the shaft."

Jan 1, 2016

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Ambarish Ghosh, Chitralekha Ghatak, Tanumaya Mitra, Tarun Sengupta, Sajib Das, Sankar Kumar Nath

"Currently construction of important structures like bridges, flyovers and high rise buildings in and around Kolkata are in full swing. These structures have mostly pile or well foundations. The design methodology and construction techniques are being employed keeping in view both the safety and economy of the project. The data presented in this investigation have been taken from Geotechnical Investigation report of Component B in connection with construction of Extradosed Cable Stayed Bridge over River Hooghly in Hooghly and Nadia district of West Bengal, India. The investigation site is located within close proximity of Eocene Hinge Zone which is being taken as the principal contributor of Earthquakes in and around Kolkata. Considering the importance of the project detailed and exhaustive geotechnical investigation has been carried out and site specific response spectra have been generated for analysis and design of the bridge. This paper presents site specific response spectra, liquefaction analysis and comparison of lateral load carrying capacity of pile using Winkler approach and IS 2911 guidelines.INTRODUCTIONPile foundations are used to transfer the load of the super structure through soft soil deposit to deeper bearing stratum by means of skin friction or end bearing or both. Pile foundations are regarded as a safe alternative for supporting structures in seismic areas and have been used for this purpose in non-liquefying as well as liquefying soils. But their design in case of potentially liquefiable soil is quite different from that of non liquefiable soil. In liquefiable soil the progressive buildup of excess pore water pressure will cause stiffness degradation and loss of strength which in turn will induce additional shear force and bending moment in the pile. The mechanism of pile behavior in liquefying soil has been investigated by several investigators in the recent years based on observations of pile performance during earthquakes and studies in the centrifuge and Shake Table tests. Exhaustive geotechnical investigation has been carried out along the proposed alignment of the Extradosed Cable Stayed Bridge i.e., along Baropara, Bansberia ROB, Ishwar Gupta Bridge, Saraswati River to collect disturbed as well as undisturbed soil sample, to develop average soil profile and to determine the design parameters. The proposed project site is very close to Eocene Hinge Zone, which is basically a strike slip fault, capable of generating an earthquake of Mw 6.7. Thus it is evident that the proposed Bridge needs to be designed considering the adverse geo-hydrological condition as well as the earthquake aspects needing special attention following the state-of-the-art technology as guided by relevant codes and published literatures. Considering the soil profile of these locations ground response analysis has been carried out using equivalent linear method to determine the site amplification. Site specific response spectra have been developed for the four zones and zone factors have been determined. The computed zone factors are 0.198g, 0.195g, 0.195g and 0.20g for the four zones respectively, much higher than the zone factor 0.16g, which is for zone III, as stipulated in IS 1893:2002."

Jan 1, 2015

By Mark D. Fuhriman, Parham Khoshkbari, Robert Fosse

Drilled displacement piles are becoming an increasingly common deep foundation choice for their relatively simple installation methods, applicability to a wide range of subsurface conditions, and versatility. The installation method includes drilling and displacement of the soil followed by delivery of fluid cement grout under pressure, and placement of steel reinforcing to complete the pile. Because the installation method uses blind processes that do not permit direct observation of the pile, it is desirable to employ redundant testing tools to complement good construction techniques and inspection practices to ensure integrity of the piles. This paper examines the use of a range of integrity testing tools used for pile installations at a major office campus development. Because the integrity of a drilled displacement pile and its performance depend to a large extent on the skill and experience of the installation crew, the paper explores how use of multiple practical tools, including automated monitoring tools on the pile installation equipment, thermal integrity profiling, and high-strain dynamic testing, ensure structural integrity of the completed piles and how redundant integrity testing methods complement good construction and inspection practices add confidence in the quality of the foundation system.

Sep 8, 2021

By Sushant Upadhyaya, Deniz Karadeniz

As part of the widening of I-64 in Williamsburg, Virginia, an extensive subsurface exploration program consisting of Standard Penetration Tests (SPT), Cone Penetration Tests (CPT), Dilatometer Tests (DMT), and Vane Shear Test was performed. In addition to these in-situ tests, an extensive laboratory testing program was completed including Consolidated-Undrained Triaxial, Unconsolidated-Undrained Triaxial, Direct Shear, and consolidation tests. The strength and the compressibility properties are deemed conservative for Yorktown and St. Mary’s Formations when evaluated based on the current topography, the existing overburden pressure and SPT values. SPT exhibited low blow counts especially within Yorktown Formation due to the increased excess pore water pressures resulting in a localized liquefaction at the tip of the split spoon sampler corresponding to remolded or fully softened strength of the soil. Therefore, the applicability of the SPT correlated soil parameters somewhat leads to conservative designs with deeper piles to achieve a desired structural load demand. Generally, the in-situ estimated soil design parameters are found to be comparable with the laboratory test results corresponding to long-term resistance gain with time. It is of practical importance to employ realistic soil design parameters for design applications such as pile foundations to provide cost and schedule savings. This paper presents a discussion on the soil strength estimates and variability from in-situ and laboratory tests for realistic strength characterization of Coastal Plain deposits.

This paper summarizes seven years of Italian ex­perience with the use of large calibration chambers for the calibration, under closely controlled stress and strain conditions, of some in situ testing devices which are used in sand deposits. At the present time two calibration chambers are operating in Italy, one at E.N.E.L.-C.R.I.S. (Milan) (*) and the other at I.S.M.E.S. (Berga­mo) (**). Both chambers can accomodate cylindrical samples 1.2 m in diameter and 1.5 m in height. A detailed description of these chambers can be found in Bellotti, et. al (1982).

Jan 1, 1987

By John L. Walkinshaw

It is obviously not possible in the time given me today to review in great detail all the research of the past 20 years that the (FHWA) has sponsored or participated in. In this presentation I will highlight some of the principal programs that I am familiar with. This handout lists practically all the reports prepared for the FHWA involving deep foundations and some related work involving the same structural elements (piles, shafts, ground anchors).

Jan 1, 1993

By Craig M. Shillaber, Joseph E. Dove, James K. Mitchell

"This paper addresses two primary factors affecting the sustainability of Deep Mixing Methods (DMMs): construction materials and handling of the spoil from wet mixing methods. We examine these factors within a life-cycle embodied energy (EE) and carbon dioxide (CO2) emissions accounting framework, using the LPV 111 project in New Orleans, LA as a case history. The underlying assumption is that project planning and preliminary design have determined that a DMM is the best ground improvement alternative for achieving the broader aims of sustainable development. While EE and CO2 emissions are direct measurements of environmental impact alone, we illustrate how their minimization can also influence the social and economic consequences of the project. It is recommended that DMMs use lower energy and carbon material alternatives to Portland cement and lime in the binder whenever possible, with preference given to locally sourced materials. Currently available alternative cementitious materials include fly ash and slag, which are waste products from other processes. In addition, recycling the spoil material from wet mix methods on site is recommended. If the material cannot be recycled on site, transporting it to a processing and recycling center for later use as fill is preferred over landfilling. INTRODUCTIONWithin the geotechnical community there is an increased appreciation for sustainability considerations, which are an important component of the planning, design, construction, operation and maintenance of projects. An assessment of project sustainability includes holistic life cycle thinking, systems analysis, environmental impact assessment, use of safe and benign materials, awareness of local societies and cultures, social equity, protecting human health and well-being, and monetary costs (Abraham, 2006). Since ground improvement is a principal practice domain of geotechnical engineers, it is important that geo-professionals play a role in addressing the sustainability for these projects. In this paper, we illustrate by case history how different materials and methods associated with deep mixing projects can impact overall project sustainability through quantifying project embodied energy (EE) and carbon dioxide (CO2) emissions. EE is defined as all energy consumed to bring something into its present state (Chau et al., 2008; Inui et al., 2011; Soga et al., 2011; Chau et al., 2012). Recommendations are then made for how adverse environmental impacts of Deep Mixing Methods (DMMs) may be minimized, leading to more sustainable geotechnical construction."

Jan 1, 2015

By Nabil F. Ismael, Khalid Farraj

"The axial load transfer along large diameter bored piles in very dense silty sand was examined by field tests. Two instrumented piles 1.2 m diameter and with embedded length of 18 m and 25 m were load tested in axial compression to failure in connection with the construction of a big tower building in Kuwait City, Kuwait. Instrumentation included vibrating wire strain gages at various levels, displacement transducers and extensometers. The purpose being to measure the axial load distribution, skin friction, and base resistance at various load levels. In addition the settlement of the piles and the elastic compression were monitored. The ultimate pile capacity, side friction, and base resistance were determined and correlated with the Standard Penetration Resistance values as determined from the boreholes. Most of the load was transferred as side friction and the pile settlements at the maximum loads ranged from 1.6% to 2.2% of the pile diameter.INTRODUCTIONLarge diameter bored piles are used with increasing frequency for heavy structures in Kuwait and the Gulf region in calcareous sand. The behavior of short piles ranging in depth from 8 m to 15 m was examined by field test (Ismael 2012). However, larger diameter and deeper piles are being used more frequently, including the project described in this paper which included piles with 1.2 m diameter and 18 m to 25 m depth. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on long large diameter piles installed through very dense sands or silty sands are very limited at present. The results of two load tests carried out recently on instrumented bored piles at one site in downtown Kuwait City have become available. In these tests the failure load was extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers."

Jan 1, 2017

By Dharmil S. Patel, Zoyav S. Benyaminov, Cassandra A. Wetzel

Rehabilitation of the Henry Hudson Bridge is nearing completion, connecting Spuyten Duyvil in the Bronx to Inwood Hill in Manhattan, New York. Constructed in 1936, the Henry Hudson Bridge spans 840 feet over the Hudson River. Challenging geotechnical aspects of this Project required a team of innovators to overcome. Rehabilitation of the existing bridge involved the replacement of sixteen bent pedestal substructures, two abutment pilasters and installation of new deep foundations at the skewbacks. However, the Bridge, roadways, adjacent Metro-North Railroad (MNR) structures and New York City (NYC) Parks land were to remain open to the public for use, with minimal disturbance. In addition to physical constraints, geologic site conditions varied widely across both sides of the River, with varying bedrock quality and depth, greatly impacting the proposed design and construction. Extensive analysis of bedrock conditions was conducted to locate areas of potential wedge failure. The implementation of anchors was used to reinforce rock stability where pedestals and pilasters were replaced. This paper describes several challenging technical and natural aspects overcome in the rehabilitation of the Henry Hudson bridge foundations, including varying geologic site conditions, access restrictions, construction limitations, project specifications and design requirements.

Sep 8, 2021

By William M. Tanner, Daniel C. Brahana

"A drilled pier foundation was originally designed to support the proposed G. Wayne Clough Undergraduate Learning Commons on the campus of Georgia Tech in Atlanta, GA. Reflective of the site geology, the original drilled pier foundation was divided into a Northern and Southern portion with an allowable end bearing capacity of 60 ksf and 100 ksf, respectively. After initial pricing on the original design, several value engineering options were submitted that featured changes to the original design capacity and construction method. The project team selected the value engineering option that involved conducting an Osterberg Load Cell test to assess end bearing of the site bedrock and skin friction. Results of the Osterberg Load Cell test justified increasing the allowable end bearing capacity of the site bedrock to 100 ksf in the Northern portion and 125 ksf in the Southern portion. Considering the final foundation design and Osterberg Load Cell test program, a net savings of approximately $259,000, or approximately 34%, was obtained over the original design.Project BackgroundThe G. Wayne Clough Undergraduate Learning Commons (CULC) is a 5-story academic building on the Georgia Tech campus in Atlanta, Georgia. The CULC was completed in 2011 and consists of a concrete frame structure supported on a drilled pier foundation.After pricing of the original drilled pier foundation design, several value engineering (VE) analyses were performed by the foundation contractor in an effort to demonstrate the potential for a reduced foundation cost. The VE analyses focused on variations in design assumptions, as well as construction techniques. This paper presents a case study that demonstrates how the value engineering process can be used to reduce foundation costs.Site Investigation and Subsurface ConditionsThe CULC building site is located within the Southern Piedmont Physiographic Province, an area underlain by metamorphic and igneous rocks. McConnell and Abrams (1984) indicate that the site is located at the boundary between two distinct geologic formations. The Northern portion of the site is underlain by the Wahoo Creek Formation while the Southern portion of the site is underlain by the Stonewall Formation. The following paragraphs briefly describe the geotechnical investigations performed by the project geotechnical engineer (GE) for the CULC."

Jan 1, 2015

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner's engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel's observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile's geotechnical and structural design, and the contractor's pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005

By Dewey W. Geary, Rachael V. Bisnett, R. Michael Bivens, Thomas G. Andrews

"The powerhouse for the Red Rock Hydroelectric Project is being constructed at the toe of the existing U.S. Army Corps of Engineers’ Red Rock Dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends though overburden and 40 feet into rock. Prior to rock excavation, a grouting was performed around the excavation for the purpose of increasing the strength of zones of fractured rock. For the majority of the perimeter, the rock was fairly tight and grout takes were relatively low. However, for a 160 foot extent along the landside of the excavation, extensive grouting was required to treat a two to five foot thick zone characterized by artesian flows from grout holes on the order of 20 gallons per minute (gpm) or higher from a voided zone in rock that was partially filled with sand, clay, and rock fragments. This paper discusses the treatment measures used to fill and improve the strength of this zone, which ultimately entailed a combination of thick cement grout and polyurethane grout, holes spaced as close as 18 inches on-center, and two additional rows of grout holes.IntroductionThe Red Rock Hydroelectric Project (Project) is currently under construction at the existing U.S. Army Corps of Engineers’ (USACE) Red Rock Dam on the Des Moines River near Pella, Iowa. At peak generation, the Project will generate up to 55 MW with an average annual energy output of 178 gigawatt-hours.The powerhouse for the Project will be located at the toe of the existing dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends up to a depth of 40 feet into rock through the St. Louis Limestone and terminates in the Warsaw Limestone. Prior to rock excavation, grouting was performed around the excavation for the purpose of improving the strength of zones of fractured rock. An auxiliary benefit of the grouting was reducing seepage into the excavation. Grouting began on July 20, 2015 and ultimately concluded on September 26, 2015.Drilling and grouting occurred as planned on the riverside (southwest) of the excavation along the cellular cofferdam and stilling basin wall (grout holes P-1 through S-13) and on the upstream (northwest) side of the excavation along the secant pile excavation support wall (grout holes P-14 through S-19) (refer to Fig. 1). The rock in these areas was generally tight with relatively low grout takes. However, on the landside (northeast) of the excavation (grout holes P-20 through P-28), partially infilled voids and artesian flows were encountered during drilling generally between depths of about 28 to 40 feet."

Jan 1, 2016

By Kim Chan, Bryn Thomas, Ben Dening

"Increased rail capacity is required into Kooragang Coal Terminal near Newcastle, NSW, Australia to relieve rail traffic congestion and improve management of train arrivals. An additional arrivals track is proposed on new embankment within a heavily constrained site located between existing railway tracks, a high pressure gas pipeline located 7m beyond the toe of the embankment and an environmentally sensitive wetland area. Ground conditions at the site consist of deep soft estuarine clays, a soil profile which is consistently encountered throughout this part of the east coast of Australia. Upon determining that a ground improvement solution was required to ensure global embankment stability, various solutions were considered including a piled viaduct, retaining walls, dry deep soil mix (DSM) columns and concrete injected columns (CICs). DSM columns were adopted as the design solution, a decision which was driven by the presence of sensitive infrastructure and a confined site. DSM offered further advantages including reduced impacts on temporary working platform design, where the use of a thinner platform could be justified owing to the lower track loads of a DSM rig relative to other ground improvement techniques.INTRODUCTIONThis paper presents a case study of the design of DSM ground improvement works to provide support for and enable safe construction of a new railway embankment over deep soft soils with a number of nearby infrastructure and other constraints. The project site is approximately 1km long and is constrained by existing railway tracks, a high pressure gas pipeline and a wetland area of ecological significance. Due to the site constraints and ground conditions, a number of ground improvement techniques were considered during the design process, with DSM columns eventually adopted. This paper discusses the design development and the particular suitability of the technique for use in this application.SITE DESCRIPTIONLandformThe site is located along the northern boundary of the Kooragang Coal Terminal (KCT) at Kooragang Island (KI), a collection of former islands located near the mouth of the Hunter River, north of Newcastle, NSW. The topography of the original area was generally flat with mudflats, swamps and mangroves existing along tidal water courses. Subsequent dredged fill reclamation and development has amalgamated the previous islands into the current KI. The site area extends over numerous channel infills including the buried former course of the Moschetto Channel (paleochannel).Figure 1 shows the proposed 1km long new rail corridor construction area in relation to the various natural and man-made site constraints including existing tracks, the high pressure gas pipeline, the wetland area and the existing reclaimed area."

Jan 1, 2015

By Dimitrios Polantzas P. E., Collin E. Sweeney E. I. T., Franklin M. Grynkiewicz P. E., Leili Javidanian P. E.

In the latest AASHTO design specifications, the Load and Resistance Factor Design (LRFD) method is prescribed for the design of retaining walls. However, inconsistencies arise when LRFD is used for retaining wall design versus the traditional Allowable Stress Design (ASD). Required toe embedment and wall loading demand vary greatly when the two design approaches are compared, all else being equal. This is due to application of linear load factors to properties that vary non-linearly in the design. These inherent inconsistencies are further intensified when introducing factors such as layered soil profiles, different wall types, groundwater elevation, and surcharge requirements. When applied correctly, these two design approaches, in theory, should lead the designer to the same result with little discrepancy, as they do with steel structure design. However, the use of the current AASHTO LRFD method for various geostructural retaining wall designs yields contradictory results that suggest existing retaining walls that have been successfully designed and constructed are unstable. Fundamentally, LRFD should be built on reliability-based calibrations; the successful past performance of existing retaining structures designed using ASD suggests that the LRFD approach requires considerable modification. The authors of this paper recommend that the current LRFD load factors be reviewed and revised based on more comprehensive wall performance data and wall type such that the difference between retaining structures designed using LRFD and those designed using ASD is eliminated.

Oct 1, 2022

By Ira Brotman

The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S. his paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20?30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition. The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project?s progress and allow for validation of consolidation and strength gain rates and magnitudes.

By Mohamed Mekkawy, William W. Wheaton, Ira Brotman

"The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S.This paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20–30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition.The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project’s progress and allow for validation of consolidation and strength gain rates and magnitudes."

Jan 1, 2017