Search Documents

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By R. Radhakrishnan, C. Gunasekaran

"Calicut Bypass Phase-II project included construction of 7 m high embankment over soft compressible clays up to 18 m in thickness. Approx 1.5 km length of road out of a total 5 km length consisted of abandoned paddy fields which were low lying, waterlogged and marshy in nature. On the basis of excellent results achieved in earlier phases of the by-pass construction, ground improvement work by installing pre-fabricated vertical drains (PVD) was undertaken to stabilize the embankment foundation along the weak clay areas prior to road pavement construction to avoid large post construction settlement as well as to improve the lateral stability during and after embankment construction. This project perhaps stands out as one of the highway projects completed within a very short time period of total 18 months including four month long heavy monsoon period, when embankment construction was not possible and construction of two bridges across rivers. All activities including the ground improvement had to be programmed and completed within the shortest time period possible. The paper discusses details of the extensive ground improvement and soil instrumentation carried out for the project and will illustrate how careful planning and execution can reduce the period required for highway projects involving ground improvement.INTRODUCTIONPhase-II construction of Calicut by-pass was undertaken on a priority basis by the State of Kerala in 2014. The main contract was awarded to M/S ULCCS Ltd, Kozhikode, Kerala and the ground improvement work was awarded to M/S Geo-Enviro Engineers P Ltd, as specialist agency to design and execute the work.Soil investigation carried out confirmed thick soft clay deposits below GL in three areas along the road alignment totaling approx 1.5 km in length. These areas were low lying, waterlogged and marshy in nature. Highway embankment had to be constructed up to 7 m in height above existing GL to form the proposed road alignment along these areas. On the basis of excellent results achieved in earlier phases of the by-pass construction using pre-fabricated vertical drains or PVD (R. Radhakrishnan, 2006), ground improvement using PVD had been included in the contract to stabilize the embankment foundation along the weak clay areas prior to highway embankment construction to avoid large post construction settlement as well as to improve lateral stability during its construction."

Jan 1, 2015

By Roger A. Bullivant

The introduction of this size and type of piling rig is intended to address a multipurpose foundation activity. The 8000 denotes the size of equipment that is attached to the mast, namely 8000 Kg. Larger equipment can be carried subject to adjustment of rig geometry. The 8000 series rig will easily accept hydraulic piling hammers and CFA equipment, but for the purpose of this discussion it will be equipped with an auxiliary power pack that is matched to twin vibrators. The design of the siamesed vibrators allows long tube equipment or piles to be driven with a short mast configuration that provides a lower overturning risk. It is easily adapted within minutes to carry out other foundation requirements that are required on the same contract. The piling and ground consolidation activities that can be undertaken by the 800 series machine are:-

Jan 1, 1995

By Thomas D. Humbert, Christopher J. Ramsey

Construction of a new underground parking structure in State College, Pennsylvania, is situated on a site constrained by limited ROW and required excavations ranging in depth from 25 ft to 40 ft. Additional complications included busy surface streets, an active intersection, and numerous underground utilities that could not be disrupted by construction activities. To combat these challenges, an innovative approach for earth retention was designed that combined multiple types of retention systems. The overall system included alternating sections of soil nail walls and a hybrid system of soldier pile walls (consisting of micropiles) that were partially restrained by a soil nail wall in the lower portions of the excavation. Further, due to the limited space within the property limits that inhibited the length of the permanent nails, the wall design team collaborated with the project designers to develop a solution such that the completed wall became an integral part of the final design/construction of the underground parking structure. INTRODUCTION HERE at State College is a mixed-use, high-rise building in State College, Pennsylvania. The 12-strory building has up to 3 levels of below-grade parking, with the above-grade levels consisting of residential and commercial/retail space. The existing property was a parking lot bound by the streets Calder Way to the north, Garner Street to the east, East Beaver Avenue to the south, and Heister Street to the west. The overall property sloped approximately 20 ft in elevation from southeast to northwest. Excavation for the below-grade levels extended 21 ft to 36 ft (6.4 m to 11 m) below street level. During design-development phases of the project, it became evident that due to subsurface conditions and right-of- way limitations, conventional construction techniques would not be feasible. The full perimeter of the excavation would require earth retention including the weak shale bedrock along the bottom of the excavation. The project developer (CA Ventures) and general contractor (Brinkmann) coordinated with the specialty contractor and wall design engineer to find a solution. At this time, Coastal Drilling East (specialty contractor) and Wood Environment & Infrastructure Solutions (wall design engineer) became involved. The project developer and general contractor were aware they needed an earth retention system, but given the many variables the project faced, a single, straightforward solution would not work in this application.

Jan 1, 2019

By Lucie Spencer, Craig Butterworth

"This paper presents the design of a raft enhanced pile group recently constructed for a hotel development in Perth, WA. At the time of construction in 2016 the hotel was the tallest prefabricated hotel in Australia.The structure covers the entire 12 m by 32 m development footprint, located in an inner city environment, and directly surrounded by existing structures. The small site and lack of space required innovative thinking in terms of the substructure design.The ground conditions comprise a layer of medium dense sand underlain by variable layers of stiff clay, silts and sands. Groundwater was around 1.5 m below ground level.The substructure design was carried out on the basis of a raft enhanced pile group. This allowed the use of much shorter piles than a conventional pile solution, thereby permitting the adoption of CFA piling techniques. This also allowed the raft thickness to be reduced to such that the substructure works were maintained above the groundwater level.The design was carried out in general accordance with the Australian Standard AS 2159 and using conventional piled raft design techniques involving iteration between elastic soil settlement software and structural analysis software until spring reactions were obtained with convergence of the two models. Following this springs were introduced to model piles in the structure.Due to the variable nature of the ground and resulting uncertainty in pile base capacity it was not considered appropriate to design the system as a pile assisted raft with piles loaded beyond their ultimate geotechnical design strength. As a result, all piles were designed based on a maximum load maintained within the elastic response region, with the majority of the load taken by the piles. However, the combined capacity of the raft and the piles allowed for a saving in pile lengths and numbers of around 40%, when compared to a conventional pile group designed in accordance with the Australian Standard AS 2159.The raft slab was monitored during construction in order to check the actual displacements against the design displacements. At the end of construction, the settlements were found to be within 2 mm of the design values.INTRODUCTIONThe Wellington Street area of Perth in the CBD is undergoing recent regeneration which includes the King’s Square development, Perth Arena and the Wellington Street Bus Station. The proposed hotel development is close to the recent developments on a Lot previously occupied by a low rise development. Due to the small size and constrained nature of the site, the substructure design for the tower needed to take into account available space and the impact of the works on adjacent properties. This paper presents reasoning for the choice of substructure design, details of the design methodology adopted, results from limited post construction monitoring and potential improvements that could be considered for similar future developments."

Jan 1, 1900

By Stephen Buttling

The construction of a water treatment plant in Dandenong, Victoria, required detention tanks and a pumping well. The design provided by the Engineer used conventional rectangular cast-in-situ reinforced concrete walls within a sheet piled cofferdam. It was decided to construct the tank and shaft using the diaphragm walling technique as an alternative and, for the shaft in particular, this involved a “circular wall”. Except where cutters are used, joints in diaphragm walls have to be made between colinear panels, with waterproofing provided by dumb-bell water stops held within trapezoidal forms. This means that the circle has to be approximated by a number of straight sides, which in this case was twelve. The requirement was to design the reinforcement for the strange shaped panels. Finite element analysis was used, in the first stage using an axisymmetric model to determine the profile of lateral earth pressures with depth. In the second stage a horizontal slice was modelled, without gravity which normally operates from the top to the bottom of the page. By considering appropriate possible earth pressures at different depths, a range of bending moments was calculated, which was used by the structural engineers to design the rebar. The tanks were successfully constructed, and inclinometers were installed in both the tank and the shaft. Measured deflection profiles show that the design was moderately conservative.

Nov 1, 2022

By Dena Morgan, Emre Biringen

"Abstract This paper discusses the execution of pile installation and design issues at two environmentally challenging industrial sites in North America. Environmental regulations set constraints on the design and require versatility in choice of technology.For a proposed bridge, due to protected fish habitat, performing soil borings within 30 m of the creek embankment was prohibited. The limited subsurface profile indicated a thick upper layer of granular material, thus driving H-piles was considered. However, to limit generation of vibration and noise in the protected area, drilled piles had to be used. During execution, the subsurface profile differed from that in the borings 30 m away. Very soft, saturated silt was encountered at the bottom of the caisson and the length had to be redesigned very quickly while the contractor waited for instruction. For a new structure in uncontrolled fill area, performing soil borings was not allowed. It was known that a layer of peat was present in the area, but no information regarding the thickness and extent. The subsurface profile generally consisted of granular material overlying a thick compressible silt layer. Somewhere within the granular layer peat would likely be encountered. Franki piles were chosen to penetrate the peat and bear in the underlying granular material. During environmental sampling in the area, methane gas was encountered and Franki piles were no longer a viable option due to safety concerns. The foundation system was changed to steel H-piles driven to bedrock, which was more than 50 m below the ground surface and sloping. Rock shoes that would work to significant slopes had to be used in order to increase the likelihood of good embedment within the bedrock. Also, due to obstruction of an approximately 3 m thick debris field that was encountered in the upper granular soils, some of the piles had to be relocated and extra piling needed to compensate for such differences. The results of PDA testing to estimate compressive capacity and a series of lateral load tests are presented.INTRODUCTIONThe design issues that are encountered during construction can be quite problematic and have a significant impact on schedule. In order to avoid such impact on the project, a thorough subsurface investigation should be considered prior to design and construction. Better understanding of environmental regulations also prevents costly changes to the foundation design. This paper discusses the execution of pile installation and the design issues at two environmentally challenging sites in North America.BRIDGEDuring the subsurface investigation for a proposed industrial building complex, several boreholes were drilled within the footprint or in close proximity of various structures, with Standard Penetration (SPT) sampling of the upper coarse-grained soils (sand/gravel) and undisturbed sampling of the lower fine-grained soils (silt/clay). The SPT blow counts (N60) were corrected by a factor of 1.35 in order to incorporate the SPT automatic energy transfer ratio. When Modified California Sampler was used, a correction factor of 0.44 to 0.64 was also applied. N60 values were further corrected for gravel to avoid artificially high blow counts during the analyses due to spoon samples contact with gravel and cobbles, and the corrected values of (NG)60 (limited to a maximum value of 50 blows/300 mm) were used for design. The information from the SPT boreholes was then used to assess the subsurface conditions beneath the structures, as well as for a nearby bridge that was designed to cross over a creek. Since performing soil borings within 30 m of the creek embankment was prohibited due to the protected fish habitat, the investigation with regard to the bridge abutments was limited to two deep boreholes (B10-33 and B10-34) at the bridge location and two additional boreholes (B10-35 and B10- 36) located approximately 200 m upstream. The bridge location and two sets of boreholes are"

Jan 1, 2014

By Lance Rasband, Richard Hanke, John Starcevich

"The 17.4 meter (57 ft) diameter tunnel boring machine (TBM), the world’s largest at the time of her launch in 2012, locally referred to as “Bertha,” is stuck. Incapacitated due to mechanical failure approximately 36 meters (120 ft) beneath downtown Seattle, situated precariously between the deteriorating Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to address all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Limited area above the tunnel alignment and the physical restrictions of existing infrastructure, create significant challenges for the design of an otherwise symmetrical shaft, requiring special attention to design and layout. Consequently, the access/recovery shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude.INTRODUCTIONTunneling on Seattle’s SR99 tunnel project began in July of 2013. After slowly mining through a 4.5 m (14.76 ft) thick fiber-reinforced concrete headwall and the first of three stabilized “safe havens,” Bertha would proceed along the proposed alignment through 122 meters (400 ft) of jet grout improved soil at a rate of slightly over 1.6 m (5.25 ft) per day. Once past the improved area, it was planned that “Bertha” – would be moving at a rate of about 11 m (36 ft) per day. By the end of October 2013, Bertha had mined roughly 131 m, (430 ft) averaging 1.4 m (4.6 ft) per day and had begun mining within native soils. By December 2013, tunneling had reached the 244 m mark and Bertha was averaging 3.6 m (11.8 ft) per day, achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.It was initially reported that an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure around the TBM, and allow visual inspection of the cutter head from within the TBM, and also to investigate for the presence of obstructions at the face of the cutter head. During this inspection, fragments of steel pipe were discovered entangled in the cutter head. The fragments were apparently from an abandoned 254 mm (10 in.) diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, tunneling resumed. It was then discovered that Bertha was only able to generate a slow crawl."

Jan 1, 2016

By Jeffrey C. Evans, Daniel G. Ruffing, Hejintao Huang

Soil-bentonite slurry trench cutoff walls are the most common type of vertical cutoff wall used in the US for seepage control and for passive control of contaminant migration at environmental sites. Design considerations are often limited to constructability considerations and a target hydraulic conductivity. With design-build contracts common, the backfill design is often left to the contractor. As a barrier soil, the hydraulic conductivity of bentonite slurry wall backfill is typically required to be equal to or below 1x10-7cm/s. The importance of stress state upon the hydraulic conductivity as well as the expected stresses are both established in the literature. Grain size distribution of the base soil and bentonite content both affect compressibility and hydraulic conductivity. This paper describes the results of studies undertaken to evaluate the interrelationships between compressibility, hydraulic conductivity, grain size distribution, and bentonite content. Three base soils were used representing a range of soils found on typical construction projects. Using these base soils, mixtures containing a range of dry bentonite contents from 0% to 5% were prepared to a slump consistent with field practice. The compressibility and hydraulic conductivity were measured in consolidometers adapted for falling head permeability tests at the end of each load increment. These experiments yielded the relationship between effective stress and hydraulic conductivity as well as consolidation characteristics including time rate of consolidation and coefficients of compressibility. The experimental results are then used to indirectly evaluate stress development and to assess the time needed for consolidation. The findings show a substantial decrease in hydraulic conductivity as effective stress increases, regardless of base soil type and dry bentonite content, a relative insensitivity of stress development to backfill compressibility, and a wide range of values for coefficient of consolidation depending upon backfill mixture and stress level.

Jan 1, 2016

By Mario Mauro

Tuttle Creek Dam was constructed by the U.S. Army Corps of Engineers in the 1950?s on the Big Blue River in north-east Kansas. Since the dam is located in a seismic area, the safety of the dam was re-evaluated under the national U.S. Army Corps of Engineers Dam Safety and Assurance Program. After a series of studies and analyses performed by the Kansas City District of the U.S. Army Corps of Engineers, in 2003 the Department of the Army authorized the implementation of the plan ?Stabilize Foundation Soil without Drawdown Alternative?, during a 7-10 year construction period. As part of this plan, in 2006 Treviicos South carried out a large scale jet grouting and deep mixing test program downstream the dam. The test program included the installation of twenty-seven double and triple-fluid jet grout columns and twenty-seven jet-assisted deep mix columns. The jet grout columns were constructed at different levels of specific energy and cement content. The deep mix columns ranged in diameter between 3 ft and 6 ft. During column placement, the drilling and grouting parameters, pore pressures, and soil movements were instrumented in real-time. The downstream test area was enclosed by a cement-bentonite wall extended to bedrock, which allowed a 35-ft deep open excavation around the 45-ft deep columns. The exposed jet grout columns measured up to 15 ft in diameter, exceeding the anticipated target diameter. In addition to coring, some of the jet grout and soil mix test columns were saw-cut along the group axis, providing useful information on the internal column structure.

Jan 1, 2008

By Chu E. Ho, Alfredas Daugiala, Nicola Ebanks

"The construction of an ancillary structure for the new Second Avenue Subway Line in Manhattan, New York City involved a deep excavation in highly variable rock conditions adjacent to a fragile masonry building. The maximum difference between the lowest and highest rock elevations was about 30 feet, which posed a problem for the installation of secant piles that formed the supporting retaining wall for the excavation. At certain areas, the rock levels were higher than the top of the invert slab of the ancillary structure. To avoid disturbance to the adjacent fragile building, the secant piles were fully cased for drilling through the overburden soils and the rock sockets were formed using non-vibratory technique. This paper discusses the design and installation details of the secant pile wall and the contingency measures that were considered to mitigate the highly variable rock conditions. Monitoring of the adjacent fragile building showed that impact of pile installation were controlled within tolerable limits and safety of the building was not compromised.INTRODUCTIONThe 96th Street Station forms part of the newly constructed Second Avenue Subway Line on the East side of Manhattan Island, New York City (Figure 1). During construction of this station, several deep excavations were carried out adjacent to existing fragile buildings (Arksman et al. 2012, Grigson et al. 2016). These fragile buildings were typically four to five stories high, with a single rubble wall basement supported on timber piles or seated directly on the fill. The timber piles were often found to be in a poor condition and connections to the footings were compromised due to rotting of the timber within the zone of water table fluctuation. Several of these fragile buildings had to be strengthened and underpinned to improve the stability of the structures prior to commencement of excavation for the new subway station box (Trabold et al. 2012, Ho and Pena-Iguaran, 2013). The situation was most challenging at Ancillary Buildings 1 and 2 located at 93rd and 97th Street respectively, where secant pile walls were located merely 2 feet away from the adjacent property line, due to architectural space constraints. While mitigation of excavation induced ground movements can be controlled by the adoption of a stiff excavation support system, a more concerning factor was the uncertainty associated with the impact of the secant pile wall installation on the stability of the existing fragile buildings. This was particularly difficult at Ancillary 1 where the secant piles encountered highly variable rock levels that intruded into the excavation space. The following sections discuss the design and installation of the secant pile wall and contingency measures that were considered at Ancillary 1."

Jan 1, 2016

By Jeff Wilkinson, Brandon Walter

"A&N Electrical Cooperative provides electrical service to the counties of Accomack and Northampton along Virginia’s Eastern Shore and to Smith Island in Somerset County, Md.A&N recently worked to improve the efficiency of power distribution to a small island community and marina on Tangier Island in the Chesapeake Bay. This improvement consisted of upgrading the existing distribution substation with a new 25 kV 2-bay box distribution structure. Earth Contact Products (ECP) collaborated with PowerServices, Inc. (PSI) to design and install a helical foundation support system as part of the substation upgrade. Feasibility EvaluationThroughout the design process, A&Nworked with its partners PSI (design) andT&D Solutions (installation) to identifycost-effective alternatives. Foundationsystems considered included cast-in-placereinforced concrete caissons, precastconcrete foundations, driven steel piles and helical piles. In evaluating all of theoptions, the greatest concern was gettingthe material onto the island, followedclosely by the availability of the equipmentto install the foundations. Clearly, cost,more specifically the installed cost, was asignificant consideration and decisionfactor throughout the process.There were several limiting factors that had to be considered during the design process, the most significant of which was that all of the material had to be barged to the site. With traditional reinforced concrete deep foundations in mind, the cost for installing these piles was projected to be nearly $2,000/cu yd ($262/cu m) of installed concrete. Given that approximately 5 to 6 cu yd (3.8 to 4.6 cu m) of concrete would be required for this structure, the cost was significantly high for this project. What’s more, because the components of the concrete mix would have to be barged and then hand mixed on site, there was concern regarding both the time required to complete the piles and the quality of the installed concrete. For the driven pile alternative, the availability, or lack thereof, of equipment and material cost resulted in a total cost estimate that was more expensive than that of the concrete piling alternative. The high material cost for the piles, which was more than double than the cost of concrete, was due to the number and size of piles needed to resist the overturning moment. Ultimately, the team selected the helical pile alternative. The decision to a use helical pile foundation system was based on many factors, not the least of which was the remote location of the project site and the difficulties associated with getting material, equipment and construction personnel to the project site."

Jan 1, 2017

By Rob van Dorp

"AbstractThe Monitoring & Instrumentation Committee (MIC) of DFI Europe has the objective to support DFI members in concern of risk management of geotechnical matters, where monitoring and instrumentation have added value.Work of the CommitteeA study by the committee showed that there are already several existing (national) guidelines. They all have their strengths and limitations and their focus may vary a little per country due to local regulations and typical local building activities, but the main question remains what added value another new guideline would have. More likely it would add to the confusion instead of providing overview.Companies with larger experience in geotechnical monitoring (often larger consultancy firm, contractors or clients) are already quite familiar with its benefits do not really need a new guideline in how to design and effectively apply sophisticated geotechnical monitoring systems for special projects.Therefore the aim of the MIC is to focus a little more towards smaller organizations - that are less familiar with monitoring and instrumentation - and the more ‘regular’ type of project that they are mainly involved in. The MIC wants to create a tool which helps them to create risk awareness, to understand the benefits of geotechnical monitoring and to provide them information about how and where to find the right partners and equipment to setup and apply appropriate monitoring systems for their projects.Monitoring and instrumentation benefits are for example:• Risk control during construction stage;• Costs reduction in design and construction (taken limitation of geotechnical aspects into account).• Prevent of unnecessary delays in construction work• Increasing general awareness of geotechnical risks and possibilities of monitoring.The cost of monitoring compared to the cost of failure and/or the savings that can be achieved play a role in the work of the committee. DFI members benefit from the shared knowledge by the MIC on monitoring and instrumentation within their process of risk management."

Jan 1, 2014

By Joel L. Volterra

Since 1910, Mueser Rutledge Consulting Engineers (MRCE) has regularly provided professional engineering services including inspection of pile load tests. Historically, such services included on-site inspection of the driving of test piles and subsequent static load tests by qualified Geotechnical Engineers. Load testing procedures are specified by local or State Building Codes, locally the 1968 Building Code of the City of New York (1968 BCCNY). Between 1968 and 2008, the 1968 BCCNY required a minimum 48-hour hold period for standard loads per pile type, an extended 96-hour hold period for higher capacity piles, and a settlement criterion that the pile maintain a test load equal to two times the design load with less than 0.012 inches of settlement over the last 48 hours of the hold period. Effective July 2008, the new 2008 BCCNY shortened the hold period and relaxed the settlement criteria to that which is more similar to other governing codes and standards such as the International Building Code (IBC 2006) and the American Society for Testing and Materials (ASTM). MRCE implemented an automated load test monitoring system to reduce costs and to alleviate or minimize overnight and off-hour staffing for load test readings. Initially, a series of linear variable differential transformers (LVDTs) and data loggers were included in the Contractor?s load test setup to electronically record pile head settlement and where applicable, settlement of telltales installed to varying depths in the pile. A pressure gage was subsequently added in the hydraulic line, then a load cell, strain gages, and remote access using modems. The ease of the setup and modular adaptive nature of this system have proven it to be a useful tool and improved our ability to better serve our clients and manage our pile load testing services.

Jan 1, 2008

By Ross T. McGillivray, David S. Graham, Dan A. Brown, Steven D. Dapp

"The Selmon Expressway includes an elevated structure extending across several miles of weathered karstic limestone geology, and represents a challenge for design because of the high variability of the material and the difficulty in characterizing the strength. The nature of the epikarst in this region of Tampa is such that variability can be extreme within distances of only a few feet. The weathered rock includes extremely soft soil infill within solution features on and within the formation. The limestone is so weathered that coring typically does not yield useful samples for strength testing, and in-situ Standard Penetration Testing (SPT) tests often encounter refusal blow counts. Thus the challenge for foundation design includes two components of reliability risks: the uncertainty associated with the ground conditions at a given foundation location plus the uncertainty associated with the foundation performance at a given location even when the stratigraphy is determined.This paper describes the design approach that has been implemented successfully for two projects at the Lee Roy Selmon Crosstown Expressway (LRS) in Tampa, Florida: the assessment and remediation of the reversible elevated lane (REL) foundations constructed in 2004, and the elevated expressways widening project constructed in 2012. Included in this design approach is a method developed for computing axial resistance in this local geology. Design for axial loading relies primarily on the development of side resistance, which was considered less subject to performance risks than base resistance. The calculation method incorporates a statistical analysis of SPT data, tempered by engineering judgment, to characterize stratigraphy at a given location into either soil, intermediate geomaterial (IGM) or rock.IntroductionThe subsurface stratigraphy of sites underlain by weathered limestone formations can be highly variable with respect to material layer thicknesses and strengths, even over short horizontal distances. This is the case for much of Florida, and particularly the Tampa area. These conditions present a challenging environment for the design of drilled foundations because of the need for a reliable determination of subsurface conditions at each foundation location, as they relate to the expected axial performance. Contributing factors include:"

Jan 1, 2015

By Sarah Ramp, Daniel V. Cacciola, Justin Labrozzi, Shafiq I. Siddiqui, Faisal Ahmed

"Construction of embankments up to 34 ft in height for twelve ramps and roadways needed for the New Jersey Turnpike Interchange 14A project required ground improvement. The subsurface conditions, consisting of up to 30-ft thick layer of highly-compressible peat and organic soils, would induce up to 8 ft of primary and 4 in. of secondary consolidation settlements to the embankments over a long period of time. Innovative ground improvement solutions were needed to meet unique challenges posed by the poor subsurface conditions, space and existing utility constraints, aggressive construction schedule, and massive size of the project. A variety of ground improvement techniques were utilized in six different zones of the embankments to limit settlements and ensure stability of the embankments. These techniques included preloading with surcharge and prefabricated vertical drains (PVD), load balancing using light weight fill, and concrete column rigid inclusions (RI). Additionally, augercast piles with load transfer platform were used under an existing bridge with low vertical clearance. An innovative approach consisting of preloading with surcharge and PVDs followed by installation of RI was needed in one of the six embankment zones with the worst, i.e., very soft, soil conditions. The design of the RI was performed by a specialty ground improvement contractor (SGIC) using Plaxis 2D and 3D softwares. The performance of the ground improvement systems was verified and monitored by load tests and instrumentations. This paper presents details of the ground improvement design, construction, monitoring results, and lessons learned, with a focus on the RI.INTRODUCTIONNew Jersey Turnpike Interchange 14A is located within the cities of Bayonne and Jersey City, in Hudson County, New Jersey. The New Jersey Turnpike Authority (NJTA) identified Interchange 14A as an area of mass congestion in need of redevelopment to improve the increasing demand of traffic and roadway safety. The New Jersey Turnpike Interchange 14A project included the construction of twelve (12) new roadways, in addition to the construction of four new bridges. The limits of construction are shown in Fig. 1.The fill height required to construct the roadway embankments varied from 2 to 34 ft. The proposed embankment side slopes varied from 6H: 1V to 2H: 1V. Additionally, mechanically-stabilized-earth (MSE) walls were utilized to retain the embankment fill along some segments of the roadways. As shown in Table 1, the proposed roadways were divided into six zones, based on location, subsurface condition, and embankment height."

Jan 1, 2017

By Rajesh A. Vaidya

A large scale piling work is undertaken in India for an important fast track industrial project. Thousands of solid square precast concrete piles are driven to depths of around 50m. Soils encountered are of alluvial origin with very soft clays varying in thickness from 10 to 18m at the top followed by medium dense to dense and occasionally very dense sand, stiff clay and finally dense to very dense sand layer as the founding layer. Recent site grading with around 4 metres thick hydraulically filled river sand necessitated driving the piles to the bottom sand layer to avoid problems on account of negative skin friction and to achieve optimum pile capacity. A process approach suggested by Bell et al (2002) to promote better understanding of the pile behaviour, pile capacity, and parameters assumed at design stage for static capacity and for wave equation analysis is followed with an aim to bring in effective economy in terms of pile length and pile installation speed. Soil investigation work is also undertaken in stages to cut down pile wastage. A judicious combination of PDA and static pile load tests is followed. Pile Driving Analyser (PDA) tests at end of driving and also at various stages of recovery of pile capacity are carried out to understand the pore pressure dissipation phenomenon. The paper attempts to present some of the valuable experiences that would go to establish precast pile as a very effective alternative to driven cast-in-situ piles and bored piles which are very common in this part of the world despite their limitations in terms of economy, speed and certain geotechnical aspects.

Jan 1, 2007

By Stephen Buttling, Zhong Rui

"A single unit gas fired power station was being built on the edge of the Gulf of Thailand in 2001. The soil conditions consisted of very soft to soft Holocene Marine Clay, and the site was part of a coast line which had been subsiding below high water mark for some time. In order to provide access around the power station a road system in a figure-of-eight formation was required, and this also needed to be above the design flood level, allowing for future settlement. A ground improvement scheme was proposed and constructed, which consisted of two spacings of prefabricated vertical drains (PVD) over two depth ranges, vacuum consolidation and pre-loading, and rigid inclusions.During the construction phase, the vacuum consolidation was applied for 202 to 221 days in different zones, and monitoring allowed a prediction that the future settlement, including secondary consolidation over a period of 25 years, would be within the range of 175 to 355 mm, which met the contract requirement of less than 400 mm.The power plant was completed and became operational in 2003. Monitoring of the road levels continued, as did the settlement, and in early 2010 the total settlement since the end of vacuum consolidation had reached about 800 mm. The monitoring data both during the ground treatment and for the following 7 years is presented and analysed. This is supported by numerical analysis using 3D finite element methods which shows good agreement with the measured data, and allows a preliminary explanation as to why the predictions were so far out.BACKGROUNDAfter a period of bidding and negotiation, the Eastern Power and Electric Co Ltd (EPEC), an Independent Power Producer, entered into an agreement with the Electricity Generating Authority of Thailand (EGAT) in November 1997 to sell them power. In 1999 an Engineering, Procurement and Construction (EPC) contract and an Operation and Maintenance contract were signed with a supplier to provide a gas-fired (with oil as a back-up fuel) 350 MW combined cycle power plant in Bang Bo, Samut Prakarn Province, east of Bangkok. The site of the plant at Bang Bo is located immediately to the east of the Samut Prakarn Wastewater Treatment Plant, adjacent to the Gulf of Thailand (see Figure 1) in an area of very soft to soft marine clay (Bangkok clay) having low shear strength and potential for excessive settlement. The site layout comprises the main Power Plant components of generating block, cooling towers, fuel unloading area and storage tanks, switchyard and administration block, separated by access roads."

Jan 1, 1900

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019