Search Documents

By Youngtak Ko

The northeastern Pacific shows the highest nodule abundance among the oceans in the world, and thus has been drawing international attention for deep-sea manganese nodule development. The objectives of this study are to construct database using geostatistics and geographic information system (GIS), to quantify rating value using probability and statistical methods, to suggest suitable sites for manganese nodule development, and to verify results using three statistical approaches. The copper and nickel contents of the nodules were determined by chemical analysis. Factors related to slope, aspect, water depth, and topography were obtained from multi-beam echo sounding data. The transparent layer thickness was determined using a sub-bottom profiler. The probability method was used to calculate each factor's rating, and the layers for different factors were summed to produce the development potential index (DPI). Result maps were constructed for manganese nodules development. The distribution pattern of DPI showed to be controlled of nodule abundance and metal contents. Verification was performed by comparing the results with sampling data in three ways: success and prediction rate, linear regression, and test of independence.

Sep 14, 2011

By P. C. Hollick

Two marine diamond deposits on concession 2b off Namaqualand along the South African Coast, have been systematically mined over the past year by the mv Moonstar. The two deposits, Smith?s Ulcer and Wedge Point Basin, are comparable in morphology, straddled the same water depths and have similar geology yet have given very different recoveries when compared to their respective grade models. These differences are best ascribed to the different style of mineralisation observed within the two deposits which has been directly controlled by the bedrock morphology. The smith?s Ulcer deposit has been formed in a metagreywacke bedrock displaying a strong north-south trending foliation which dips steeply to the west. Consequently the mineralisation is confined to narrow north-south linear trends with limited lateral extent (less than 5m) making extraction extremely difficult and somewhat variable. RE factors (recovered grade versus estimated grade) for this deposit range from 0.5 to 1.1. The Wedge Point Basin deposit is formed in a micaceous metaquartzite with a conjugate southwest northwest joint set, the southwest lineation being the more prominent, and structural foliation dipping gently to the west. The resultant style of mineralisation is confined to basinal features defined by topographical lows and is fairly lateral in extent (in order of 50m). Extraction of the mineralisation from this deposit is less arduous with recoveries more uniform, RE factors are frequently in the range 2 - 3. This style of mineralisation is more in line with what is to be expected from marine alluvial deposits, the nugget effect of diamond concentration being responsible for the high RE factor. The long narrow linear trends observed in Smith?s Ulcer demonstrably require a specialised approach in successfully sampling, modeling and ultimately mining.

Jan 1, 1998

By Kristian Drivenes, Steinar L. Ellefmo, Kurt Aasly, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Since Ellefmo et al. (2014) published resource estimates of undiscovered seafloor massive sulfides (SMS) on the Arctic Mid-Ocean Ridge (AMOR), there has been an increased focus on establishing new knowledge about exploitation technologies for such deposits. This also includes understanding the process mineralogical properties of typical SMS deposits.The part of the AMOR that lies between Jan Mayen and the Svalbard Islands and is located within Norwegian jurisdiction and, as such, investigating the potential for mineral production from hydrothermal vent fields has been seen as strategic. The AMOR has been explored for active hydrothermal vent fields since early 2000s (Pedersen et al., 2010b). One of the active vent fields discovered, Loki´s Castle, is located in the northern part of Mohn´s Ridge. This vent field was first described by Pedersen et al., (2010a) and consists of two mounds, each approximately 100-150 m diameter and 20-30 meters high, hosting several active chimneys, up to 11 m high.Loki´s Castle has been selected as a case site in order to study the properties of typical SMS occurrences with respect to possible future deep-sea mining activities. As part of the MarMine cruise in 2016, the Loki Castle was visited and sampled for e.g. mineral characterization and mineral processing analyses. In total, more than 500 kg rock samples were collected using ROVs, and intended for further research (Ludvigsen et al., 2016). In addition to sampling mineralized rock fragments, survey data like bathymetry, magnetics and Underwater Hyperspectral Imaging (UHI) was collected using Automated Underwater Vehicle (AUV)."

Jan 1, 2017

By Eric J. Foell

Recognizing that the planned commercial exploitation of polymetallic nodules in the deep sea should be accompanied by environmental studies in order to protect this largest and least understood ecosystem of our planet, the German Ministry for Research and Technology has since 1989 funded a longterm and large-scale disturbance-recolonization (DISCOL) experiment in the abyssal Peru Basin of the equatorial South Pacific Ocean. The circular study site is located at 4150m depths and encompasses about 10km2 of relatively flat, heavily sedimented sea floor with low (< 15%) nodule coverage near an existing German nodule mining exploration license area. The RV SONNE, a large and well-equipped multi-purpose research vessel, served as platform for all environmental cruises conducted to date. The initial DISCOL expedition (SO-61, Feb.-March 1989) was carried out in two legs. During DISCOL 1/1, a study site was selected, a pre-disturbance baseline assessment was undertaken, and sea floor disruption was begun using the "plow-harrow", a uniquely designed disturber device towed repeatedly across the circular study area. During DISCOL 1/2, disturber deployments continued until the device had created 78 criss-crossing and partially overlapping tracks along which nodules were essentially plowed under while sediment from up to 15cm below the seabed had been turned over and exposed at the surface. In addition to the obvious within disturber track impacts, sediment mobilized by plowing drifted off with the prevailing near-bottom current and redeposited downstream, blanketing nearby areas not directly disturbed. Immediately after the disturbance phase, an initial post-impact sampling series was performed. The DISCOL Experimental Area (DEA) was revisited about six months (DISCOL 2, SO-64, Sept. 1989), three years (DISCOL 3, SO-77, Feb. 1992), and seven years (ATESEPP SO-106, Jan.-March 1996) after disturbance to collect further post-impact samples, monitor changes in the benthic community and follow the recolonization process. In addition to benthic community studies, plankton investigations were initiated during the third DISCOL cruise (SO-77) and continued during three further cruises (SO-78, SO-79 and SO-80/2) in 1992.

Jan 1, 1996

By LeRon E. Bielak

Public Law 103-426 was signed into law in October 1994. Its provisions amended sections 8(k) and 20(a) of the Outer Continental Shelf Lands Act (OCSLA). The 8(k) amendment provides the Secretary of the U.S. Department of the Interior 001) with new discretionary authority to negotiate agreements for using Outer Continental Shelf (OCS) sand, gravel, and shell resources for certain projects of public benefit (e.g, beach, shoreline and coastal wetlands restoration that are under- taken by a Federal, State or local government agency). The new law also covers construction projects that are funded wholly or in part or authorized by the Federal Government. Under the law, the Secretary may assess a fee for use of the resource by taking into consideration the value of the resource and the public interest served. The law also requires that any Federal agency proposing to make use of OCS sand, gravel, or shell resources enter into a Memorandum of Agreement (MOA) with the DOI. An MOA would promote efficient coordination and resolution of inter- agency scheduling and issues. The law requires that Congress be notified before use is made of these OCS resources. The amendment to section 20(a) of the OCSLA clarifies that obligations concerning environmental studies extend to non- competitive lease situations and includes minerals other than oil and gas. The Minerals Management Service (MMS) is the DO1 agency responsible for interpreting and implementing the provisions of Public Law 103-426. The negotiated agreement approach is distinctly different from the competitive bidding requirements that have applied to all OCS minerals since the inception of the OCSLA. The MMS has opted to implement the new law in a nontraditional manner. Rather than issuinga body of new regulations to cover the negotiated agreement situation, or attempting to amend three sets of existing regulations, MMS is pursuing a less formal approach of providing guidelines. More weight is placed on the negotiation process itself and the legal agreement that consummates the process as the means for establishing ground rules, terms, and conditions under which qualifying projects may be conducted. This process must recognize and adhere to requirements of other laws, including the National Environmental Policy Act.

Jan 1, 1995

By Raymond A. Binns

In this first sub-seafloor examination of an active hydrothermal system hosted by felsic volcanic rocks at a convergent plate margin, we drilled 13 holes altogether, achieving deep cored penetrations at two sites. Our aims were (1) to delineate the lateral and vertical variability in mineralisation and alteration patterns below the PACMANUS hydrothermal site near the 1650-1700 m-deep crest of Pual Ridge in the eastern Manus back-arc basin, so as to understand links between volcanological, structural and hydrothermal phenomena, and (2) to establish the nature and extent of microbial activity within the system. Technological innovations vital to success included our precise location of holes on small targets with drill-stem video, the use of a new hard-rock re-entry strategy, and deployment of casing with a new hammer drill. Other technical achievements were the first ODP application of an advanced diamond coring system, and the first direct comparison in a hardrock environment between structural images obtained by wireline methods and by logging-while-drilling (resistivity-at-bit).

Jan 1, 2002

An extensive ferromanganese nodule field south of New Zealand (Fig. 1) has existed beneath the flow of the Deep Western Boundary Current (DWBC) and Antarctic Circumpolar Current (ACC) for at least the past 15 m.y. West of 174°E, between 59°S and 48°S, the field is 300-500 km wide, but east of 174°E, where current flow impinges on the eastern slope of the Campbell Plateau, the field narrows from ca. 200 km at 55°S to ca. 120 km at 51°S. This narrowing coincides with deflection of current flow eastwards, and consequent reduction in bottom-current velocity and eddy kinetic energy. Based on sea floor photographs, dredge samples and 3.5 kHz profile data, six distinct seafloor substrates are delineated, forming broadly parallel zones eastwards from the lowermost Campbell Slope (Fig. 2).

Jan 1, 2003

By Mark D. Hannington

Seafloor polymetallic sulfides have been found in diverse volcanic and tectonic settings on the ocean floor at water depths ranging from 3700 meters to <1500 meters. More than 100 occurrences of hydrothermal mineralization have been documented (including Fe-oxide deposits, Mn-crusts, metalliferous sediments, and massive sulfides), but high-temperature hydrothermal activity and large accumulations of polymetallic sulfides are known at fewer than 20 different sites. Chemical analyses of samples from these deposits indicate that they contain important concentrations of Cu, Zn, Ag, and Au, comparable to those of massive sulfide deposits on land. However, the lack of sufficient data concerning the distribution, size, and bulk composition of seafloor deposits precludes a meaningful assessment of their resource potential.

Jan 1, 1994

By James R. Hein

Barite and Fe-Mn-oxide deposits that occur along faults in the Southern California Borderland formed by low-temperature hydrothermal processes. The Borderland region consists of block-faulted continental crust within the broad transform boundary of the North American plate. The fault-bounded basins are anoxic and partially filled with hemipelagic and turbidite sediments. Barite was collected from four dredges and a submersible dive (DSV4-355) in the southern California Borderland, and was collected from two sea-cliff sites along the Palos Verdes Headlands near Los Angeles. Barite at these seven locations occurs along strike-slip and basin-margin faults from the shoreline to 1800 m water depth. Submersible observations showed a series of mounds up to 10-m high composed of friable, white barite associated with diffusely venting milky fluid; the mounds support large benthic colonies, including tube worms (Lonsdale, 1979). Barite samples recovered from dredges are brown, green, and white and range from porous, vuggy fragments to massive fragments cut by banded barite veins. Samples from two dredge sites contain fossil worm tubes 1-3 mm in diameter and >10 cm long. All the samples are nearly pure barite, with only minor to trace amounts of other minerals. Chemical analyses show 94-98 wt. % BaSO4, low total rare-earth element (REE) contents (<45 ppm), Sr contents from <2 to 10,000 ppm, and Hg contents up to 1 ppm. Chondrite and shale-normalized REE patterns show light REE enrichments and large positive Eu anomalies. These REE pattern characteristics are typical of marine hydrothermal fluids and minerals. Sulfur isotope ratios (d34SCTD) from +21.6 to +67.4? range from seawater values (+21?) to exceptionally high positive values. Strontium isotope ratios are lower than the modern seawater ratio as well as the seawater ratio that existed at the time of deposition of the host rocks.

Jan 1, 2002

By Ivo Dreiseitl

Bottom sediment sampling by means of a box corer, as a direct method of deep seabed exploration for polymetallic nodules, is the most comprehensive way to obtain various types of geological information on points forming a network of stations. However, direct information is lacking from areas separating those stations and has to be approximated by interpolation or extrapolation, which leads to uncertainties. Sediment sampling with a gravity or piston corer can provide information on the superficial, up to 4 m thick, part of the sedimentary cover. As opposed to box coring, gravity or piston coring provides no information on nodule abundance. Information for unsampled areas can be gained by application of remote techniques of exploration. The techniques of choice in visualising nodule-rich fields, nodule-free areas, hard rock outcrops and other obstacles for seafloor mining involve using sonar and continuous deep sea (CDS) camera. Seafloor mapping can be rendered with two major sonar types: the side scan sonar used to obtain seafloor imagery and multibeam sonar for bathymetric data; the two types are usually combined and work with an intermediate frequency profiler. Photo-profiling by means of a deep sea towed camera provides a series of seafloor photographs, each supplemented with information on the area covered by each frame, including the nodule abundance. Remote techniques have been quite frequently applied by the Interoceanmetal Joint Organization (IOM) in nodule field exploration. Recently, geoacoustic techniques (side scan sonar + profiler) and CDS were applied for exploration of IOM?s first prime area H11 (5372 km2) on 6 transects. During the IOM-2009 cruise, a total of 295 km of geoacoustic transects and 344 km of photo-transects were surveyed. The data obtained were processed with the aid of earlier information produced by multibeam sonar surveys. The aim of this paper is to demonstrate the advantages of remote techniques, particularly with regard to application of the towfish device, for geological and geotechnical applications in exploration for polymetallic nodules.

Sep 14, 2011

By D. S. Cronan

Studies on polymetallic manganese nodules and Co-rich crusts in the EEZ&apos;s of the Cook, Line, Ellice and Phoenix Islands between 0-20°S show that Ni and Cu reach their greatest combined abundances of over 2% between 2-8°S on the southern margin of the equatorial zone of high biological productivity, as a result of biological fluxing of Ni and Cu to the nodules at and just below the CCD. By contrast, Co reaches it greatest abundance of 0.6% south of 8°S in nodules on non-biogenic clays well below the CCD where little biological Co supply is likely. Nodule abundances are greatest (up to 30kg/m2) in the Co-rich area in part due to AABW flow, giving highest overall metal quantities per sq meter in the nodules there, particularly of Co. There are approximately 110 x 106 tonnnes of combined Ni plus Cu plus Co expressed as Ni equivalent in Cook Islands EEZ nodules, approximately 12 x 106t. in Phoenix Islands ones, and approximately 1.4 x 106 t. in Ellice Islands ones, in areas of greater than 5kg/m2 nodule abundance. In the Co-rich crusts, Co averages about 0.7% and crust thickness about 1.6cm, both related to metal fluxes in and adjacent to the 02 minimum zone in association with which both maximum thicknesses and Co grades occur. Within the Cook Islands permissive area there are about 930 x 103 t. of Co and 630 x 103 t. of Ni in crusts, in Phoenix Islands crusts there are about 69 x 103 t. of Co and 55 x 103 t. of Ni, and in Ellice Islands crusts there are about

Jan 1, 1989

By Charles L. Morgan

The Minerals Management Service of the U.S. Department of the Interior and the State of Hawaii Department of Planning and Economic Development are investigating the cobalt-rich ferromanganese oxide crust deposits found within the Exclusive Economic Zones (EEZ) of the Hawaiian Islands and Johnston Atoll. The objective of this investigation is to complete a preliminary resource assessment and an Environmental Impact Statement for potential leasing of mineral rights to these crusts. The results of this effort will be summarized and published in a Draft Environmental Impact Statement in March 1986. Three oceanographic cruises to deposit sites in the Hawaiian Islands EEZ were conducted by the University of Hawaii in 1984. As a result, data and sample analysis yielded the following resource estimates (in thousand tonnes): (1) total crusts - 378,500; (2) cobalt - 2,500; (3) manganese - 76,200; (4) iron - 59,700; and (5) nickel - 1,400. These estimates do not include key factors such as deposit continuity, recoverability, and environmental sensitivity. A preliminary attempt to quantify some of these factors for one particular deposit is in progress and will consist of detailed field studies followed by laboratory analysis. Similar evaluations of the Johnston Island EEZ have also begun and are based upon field work conducted by West German researchers and the U.S. Geological Survey. The Johnston Island EEZ appears to have crust resources about as large as those contained in the entire Hawaiian EEZ.

Jan 1, 1985

By Andrea Koschinsky

Ferromanganese crusts have traditionally been considered a potential ore for Co, whereas ferromanganese nodules have typically been considered a potential ore for Ni and Cu. However, both nodules and crusts sequester high concentrations of many metals (Table 1) from sediment pore waters and seawater, many of which are essential for high-tech applications. The resource potential of these rare and valuable metals is poorly known and they are the subject of considerable current research. The need for adequate and dependable supplies of these metals is essential for the development of new technologies. The rare-earth elements have recently received much attention in the scientific and popular press because of their use in so many high-tech applications and because more than 95% of the production comes from China (e.g., Service 2010); consequently, there is concern about the possibility of a significant decrease or even curtailment in exports from China. The lack of a primary source and the inadequate supply of Te have prohibited the development of a Cd-Te photovoltaic solar-cell industry (Hein et al. 2010). Inadequate supplies of many of the elements listed in Table 1 are limiting the development of key high-tech industries, forcing the use of alternative metals that [ ] may result in less efficiency or less favorable properties for a product. The rare-earth elements, Te, and other elements listed in Table 1 occur in high abundances in marine hydrogenetic and diagenetic ferromanganese deposits. Here, we look at the mechanisms by which these rare and valuable metals are incorporated into different genetic types of marine ferromanganese deposits.

Jan 1, 2010

By Sven Petersen, Berit Lehrmann, Bramley J. Murton, Paul A. J. Lusty

"INTRODUCTIONToday’s metal mining focusses on land based ore deposits which only consider one third of the Earth’s surface. Through an increasing global demand of strategic metals used in the electronic and green industry (Zepf et al. 2014), ‘uneconomic’ sites of lower grade in more technical challenging grounds such as greater depth and/or more remote areas are developed by the mining industry often resulting in higher environmental impact. However, considering the steady growth of the Earth population a shortage of certain metals may occur (Krausmann et al. 2009). In 2010, the United Nations allowed commercial exploration for seafloor massive sulphides (SMS) in international waters with currently six contractor licenses being granted.Although the number of discovered vent sites has steadily increased since the first discovery of hydrothermal venting at the Galapagos Rift in 1977 (Corliss et al. 1979) with more than 600 sites being known today, their economic potential is poorly constrained. So far Nautilus Minerals Inc., a Canadian mining company, is the only company having conducted a NI 43-101 resource estimate for the Solwara site, located in the territorial waters of Papua New Guinea. Other studies using bulk geochemical data from 95 sites published in literature do exist (Hannington et al. 2011, Monecke et al. 2016) suggesting a global resource potential for today’s known SMS deposits of 600 million tons with a median grade of 3 wt.-% copper, 9 wt.-% zinc, 2 g/t gold and 100 g/t silver. However, the geochemical data being used originated mainly from easily recoverable, mainly non insitu surface grab-samples and are under current mineral resource classification schemes such as JORC code or NI 43-101 not even accepted for resource estimations. Furthermore surface samples such as high-temperature sulphide chimney and talus material are not representative for the entire deposits with information regards thickness and continuity of individual sulphide layers obtained through drilling being scarce. In addition, it remains unknown what geological processes occur once hydrothermal activity ceases and whether metal tenor becomes enriched, depleted or disappears."

Jan 1, 2017

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By David Gwyther

There is increasing recognition that in order for a development project to proceed successfully, it must first obtain a ?social licence to operate? from concerned stakeholders. Obtaining this ?licence? is in many ways a separate process to the legal one which involves, among other things, submitting an environmental and social impact assessment (ESIA) to the appropriate regulatory authority for review. Essentially, the function of an ESIA is to present a project?s technical, financial and social benefits, together with its environmental and social impacts in a transparent way to enable regulators to make an informed decision about whether the benefits outweigh the impacts, and thus whether or not the proposed project should proceed. The focus in the early days of ESIAs was primarily technical and was aimed to answer two fundamental questions: ?Can the project be built?? and ?Can we minimise impacts to a level that is acceptable to the community?? Basically, the ESIA process was a technical test of competence, but more recently, ESIAs have become much more than this. The main ESIA risk is now more akin to a test of a project?s legitimacy ? i.e., with more weight placed on the social licence, or the political test of moral authority ? with the process involving stakeholders from multiple backgrounds and disciplines, including some anti-development NGOs/civil society groups with their views on mining, (particularly in developing nations), often already pre-determined. Within the backdrop of this potential maelstrom, now enter a proposal for a new industry (such as deep sea mineral extraction).

Jan 1, 2011

By Robert G. Ditchburn

The NW caldera hydrothermal vent field at Brothers volcano, of the Kermadec-Tonga arc, has associated massive sulfide mineralization. This includes an abundance of black smoker chimneys that contain significant concentrations of copper, lead, zinc and gold (de Ronde et al., 2005; de Ronde et al, 2010, under review). [ ] The oldest volcanic massive sulphide (VMS) samples recovered so far from Brothers have been dated using radiometric methods at GNS Science and found to be c. 1000 years old. By contrast, a volcanic cone that has formed in the southern part of the caldera has no associated VMS. Only elemental sulphur and Fe-oxide crusts are present here, samples of which have been analysed for their trace elements. From d34S values of sulfates and native sulfur, and the volume of gas (dominated by CO2 and H2S) discharging at the cone site, elements being deposited here are considered more directly magmatic in origin (de Ronde et al., 2005; 2010 under review). It has been discovered that deep-seated changes in volcanic activity at Brothers affect the NW caldera and cone site simultaneously, though the mineralogy at each site is so very different. Thus, the cone site is being studied to determine if elements being deposited there can be used as predictors of potential future VMS mineralisation as similar sites have been found at other volcanoes along the Kermadec arc and elsewhere. The frequency of these deep-seated magmatic events is considered important in the formation of Cu-Au-rich mineralization along arcs. The analysis of Fe within resulting hydrothermal plumes (surveyed by surface vessels), and trace elements in rock and mineral samples, are used to help determine the influence of magmatic contributions to the hydrothermal system. To verify that plumes are a reliable proxy for hydrothermal events depositing iron on the seafloor, Fe-oxide crusts from Brothers volcano cone have been dated to see if their emplacement coincides with highly Fe-enriched plumes in the water column. The radiometric dating techniques developed for barite-rich VMS, i.e. using 228Ra and 226Ra, were unsuitable for the Fe-oxide crusts because 210Pb was the only isotope detected by gamma spectrometry. Therefore, new techniques using 210Pb, 10Be and arsenic have been established.

Jan 1, 2010

By M. E. Williamson

In September 2005 Williamson & Associates, Inc. delivered the BMS2 remotely operated seafloor coring system to the Japan Oil, Gas & Minerals National Corporation (JOGMEC). During acceptance trials aboard the JOGMEC research vessel R/V Hakurei Maru No. 2 the BMS2 successfully recovered 7.44 m of rock core in 3377 m water at a site near the crest of a seamount about 500 nm SE of Japan. Hydrogenous ferromanganese oxide crust, basaltic lava, sandstone and volcanic sediments were sampled with near 100% core recovery. The BMS uses rotary rod coring tools to collect samples to a maximum depth of 30 m in water depths up to 6000 m. Depending on bottom type to be sampled, the BMS tool magazine can be loaded with various drilling tools including core barrels with different bit types, drill rod and bore hole casing. The drill has 9 video cameras, a suite of sensors and 60 hydraulic functions powering thrusters, telescoping legs, seawater pumps and all of the standard drilling controls. The BMS provides deep water investigations with the functionality of conventional diamond bit rod drilling currently the mainstay of exploration programs in land mining.

Jan 1, 2005

By Willam R. Normark

During a series of dives with the submersible ALVIN in 1984, samples of massive sulfide were recovered from four vent sites. All sites occur within a linear, steep-walled cleft about 50 m wide and as much as 30 m deep. The cleft bisects the axial valley floor throughout the 15-km-long study area and appears to have been the source for the most recent volcanic eruptions in the valley. Three of the vent sites are defined by a set of discrete hydrothermal discharge zones; as many as eight have been identified over a distance of 500-800 m along the cleft floor. Sulfide deposits occur as individual and coalesced mounds, spires, and chimneys generally less than 3 m in height but a few might be as high as 10 m. The vents are also marked by extensive, yellow-to-amber ferruginous sediment and clots of bacterial matter. Some vents have extensive colonies of tube worms, gastropods, mollusks, and several predator species, such as crabs and squid. The fourth vent site has no visible discharge and consists mainly of "dead" spires and chimneys of massive sulfide. The massive sulfide samples collected with ALVIN are primarily sphalerite with minor marcasite, pyrite, pyrrhotite, isocubanite, chalcopyrite, wurtzite, and anhydrite. Bulk analyses of these chimney and spire samples show Zn contents approaching 60% by weight and significant enrichments in Ag and Cu. Vent fluids have the highest concentrations yet reported for Zn, Fe, and Mn. Thus, the Zn- and Ag-rich nature of massive sulfide from the southern Juan de Fuca Ridge study area

Jan 1, 1985

By Sven Petersen, Iain J. Stobbs, Bramley J. Murton, Paul A. J. Lusty

"INTRODUCTIONIt is widely thought that seafloor massive sulphide (SMS) deposits, the modern analogue of volcanogenic massive sulphide (VMS) deposits, present a potential global resource for base (Cu, Zn) and precious metals (Au, Ag). In addition, SMS deposits can be enriched in ‘critical metals’ including Se, Te, Tl [1], which are essential for use in the construction of modern and green technologies. Globally over 340 high temperature hydrothermal sites have been identified at a range of ocean spreading centres [2], significant massive sulphide deposit formation has been recorded at 165 of these sites [3].To date only 13 deep sea sulphide deposits have undergone intrusive investigation (drilling or coring) and of these, only 6 sites have published tonnage estimates [2]. Almost all research and drilling of SMS deposits has been focused on active systems, the investigation of the morphology, subsurface structure and mineralogy of hydrothermally extinct seafloor massive sulphide (eSMS) deposits is almost non-existent.As such, little is known about the mechanisms that operate post-SMS formation and which have an impact on the preservation and hence resource value of SMS. Identifying these generic processes and mechanisms, and the extent to which they impact the resource grade, is critical in evaluating the global potential of SMS."

Jan 1, 2017