Search Documents

By E. A. Brocchi

This work is dedicated to the chemical treatment of a typical EAF dust by chlorine content agents. The residue contains 48% Fe2O3 and 28% ZnO mainly in the franklinite structural form. The others less compounds are: 4.00% CaO, 2.60% MnO, 2.20% MgO, 1.08% PbO, 0.36% Cr2O3, 0.21% B2O3, 0.03% CdO and 0.01% NiO. The experiments purpose is selectively to remove zinc from the residue leaving the iron behind. Thermodynamics studies have indicated some roasting possibilities. The experimental results have shown that both HCl leaching and carbochlorination will remove iron and zinc without any selectivity. However, either the chlorine or the calcium chloride roasting seems to form, preferentially, the zinc chloride. So, it will be presented how the EAF Dust can be treated by the using of chlorine roastings process such as carbochlorination in order to separate the zinc and iron present in the frankilinite, main EAF dust content.

Jan 1, 2014

The ball level and pulp load play a key role in the operation of industrial scale ball mills. These two operating variables have a significant influence on the performance of the ball mill and any attempts to optimize these devices require manipulating either one or both of these variables. There are several models that can be employed to perform simulations to optimize the performance of industrial ball mills. However, most of these models require ball load and pulp load measurements as inputs to calibrate the model. The changes suggested by the simulator also provide operating regimes that involve moving either the ball level or pulp load and sometimes both of these variables. A ball mill model coded in JKSimMet was used in conjunction with the Sensomag to optimize the secondary ball mill at Waterval concentrator in South Africa. The results show that the perfect mixing ball mill model can be used in conjunction with the Sensomag to optimize the performance of the secondary ball mill.

Sep 1, 2012

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By R. Van Hille, S. Lacour, A. E. Lewis, K. Peterson

"This paper compares thermodynamic modelling results with those obtained for copper sulphide removal from aqueous solution in both continuous and batch experiments at laboratory scale. Sulphide precipitation has been demonstrated to be an effective method for heavy metal removal. The advantages are the high degree of metal removal at low pH, low quantities of sludge formation, the ease of de-watering and low reactor retention time due to high reactivity of sulphides. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines, which are difficult to remove.Theoretical modelling was carried out using ASPEN Plus™ and OLI systems Inc ESP process. Both simulators were used to calculate copper sulphide recovery and residual aqueous copper concentrations as a function of pH. The predictions were then compared with experimental results. Both simulations predicted that all of the inlet copper would precipitate as sulphide CuS(s) over the entire range of pH and sulphide: copper molar ratios investigated. The simulation results were strongly influenced by the number of chemical species and the nature of the thermodynamic data taken into account in the model.The continuous experimental studies were carried out in a fluidised bed reactor (FBR). Copper sulphate was reacted with sodium sulphide and the solid precipitated directly onto the pellets in the FBR. The use of sulphide was motivated by high sulphate levels in local acid mine drainage and the ultimate integration of the metal removal process with a biological sulphate reducing process that produces an aqueous sulphide stream.A maximum dissolved copper removal of 99.6% (AAS analysis) and a total removal efficiency of 95.8% (dissolved copper minus fines) were achieved. Stoichiometry of the precipitate was determined from SEM/EDAX analysis (atomic percentages) and was close to 1/1, irrespective of the operating conditions."

Jan 1, 2003

By O. D. Khmelnitskaya

The research on selecting of an efficient technology of pyrite cinders complex treatment, sulfuric acid production wastes, have been made. The grades in the initial product were 2.04 g Au/t, 35.0 g Ag /t, 0.38%Cu, 1.1% Zn. Laboratory tests on cyanide technology, thiourea and sulphite leaching were carried out. Magnetic and flotation beneficiation and biohydrometallurgical technology were tested. After considering the results of the tests, the most economically efficient technology of pyrite cinders complex treatment with cyanide leaching of precious metals was determined. The technology involves water washing of soluble copper and zinc compounds, lime treatment and cyanide leaching of gold and silver, detoxification and utilization of mineral wastes. The precious metals are recovered from solutions by cementation onto zinc. Copper is recovered from rinse waters by SW/EW and then zinc is precipitated as hydroxide. All the solutions and organic agent are used in recirculation and therefore the technology is practically waste-free. Mineral wastes can be used as iron-containing materials for cement industry. The technology has been tested in pilot-plant scale under continuous operation with complete re-circulation of cyanide solutions. In this process recovery of 54% Au, 45% Ag, 30% Cu and 50% Zn has been achieved.

Jan 1, 2014

By A. Tolentino, J. Bravo, M. A. Corona-Arroyo, C. Quintero, R. Zarate, A. Lynch, L. Carillo

"This paper presents the performance of the flotation circuit of Minera Fresnillo PLC, Mexico. A plant survey was carried out on the lead banks and a size-by-size assay on the samples was conducted. The results indicate that the plant is treating fine particles in the flotation circuit. At least 30% of the particles in the feed are finer than 8 microns and that high amounts of Pb, Au, Ag and insolubles are in this particle size. It was also found that higher percentage of insolubles in the -8 micron particles are recovered in the final concentrate rather than being rejected in the tails. The presence of high amounts of insolubles in the concentrate is an issue of the company. The result of the plant survey provided valuable information for effective reduction of the insolubles in the concentrate and for plant optimization. The work conducted is part of the training of the students involved in a mine placement in the Alban Lynch Student Venture. INTRODUCTION Minera Fresnillo is one of the operating mines and the main contributor to the silver production of Fresnillo PLC group, the world’s leading producer of silver from ore. It is located in the mining district of Zacatecaz, Mexico, approximately 650 kilometers from Mexico City. The major minerals that make up the ore are galena, sphalerite, tetrahedrite, pyrargyrite, proustite, polybasite, pyrite and pyrrhotite. Minera Fresnillo has a capacity to treat 8300 tonnes of ore per day. The plant consists of semi-autogenous mill - ball mill – hydrocyclone circuit for primary grinding followed by silver-lead flotation then zinc flotation circuits. This paper reports the plant audit conducted in the silver-lead flotation circuit (Figure 1) of Minera Fresnillo. The circuit includes rougher, scavenger and two stages of cleaning. The tails from the scavenger goes to the zinc flotation circuit while the second cleaner yields the final silver-lead concentrate. The feed to the circuit has a particle size of 90% finer than 75 microns and generates a concentrate with grade of about 35% Pb, 5700 g/ton Ag, 16 g/ton Au and recoveries of 90% Pb, 90% Ag, 64% Au, respectively. Although the plant achieves their target concentrate grade and recovery, the concentrate also contains significant amount of insoluble materials which is about 18%. These insoluble materials consist of gangue minerals. The plant audit was conducted primarily to determine the possibility of further reducing the amount of insoluble materials present in the silver-lead concentrate."

Jan 1, 2018

By L. Z. Li

The application of some environment-friendly mineral processing technology was introduced in Xitieshan lead?zinc mine and Hugary copper mine of China Western Mining Co., Ltd, located in western plateau area where the ecological environment is extremely fragile. The results of the significant economic efficiency were obtained by applying these new techniques while the protection of peripheral environment and the improvement of ecology were made.

Jan 1, 2014

By Avinash Tripathi

It is now well known that the size distribution of the particulate solid has a significant effect on the breakage behavior of particles in the wet as well as dry modes of ball milling operation. In the context of the size discretized batch grinding kinetic model, grinding behavior of particles is characterized by the breakage rate parameters, k, and breakage distribution parameters, B. Understanding the nature of variation of these two sets of parameters with particle size distribution is important for simulation and control of operation of production mills. However, so far it has not been possible to track the variation of both the set of parameters with grinding time simultaneously. In this paper an attempt has been made in this direction by using a modified functional form approach with time dependent constants. Keywords: dry and wet ball milling, breakage rate and distribution parameters, effect of particle size distribution

Sep 1, 2012

Incomplete liberation of mineral particles is one of the key factors limiting the performance of industrial flotation circuits. This work aims to quantify the relationship between different breakage modes and how these affect mineral liberation properties. A copper porphyry (bornite) ore sample was subjected to breakage using a piston-die compression unit and an impact mill. The particles produced as a result of each mode of breakage were then characterised using Mineral Liberation Analysis (MLA) to quantify the mineralogical and liberation properties of the progeny particles. The impact mill was found to produce bornite that was finer grained relative to the host particles. In con-trast, bornite discharged from the piston-die unit closely followed the size distribution of the host particles and was retained to a greater extent in the larger/intermediate size fractions. The results provide insight into what breakage methods are optimal for the purposes of downstream separation.

Jan 1, 2014

By F. A. V. Guimarães, A. M. Costa

"The moisture in sintering is a very important parameter for the performance of the process. It allows that the granulation takes pace in an efficient way making the water bridges between the bigger particles used as nucleus and the finer particles that perform the coating of those coarse particles. The formation of the micro pellets is extremely important to prevent loss in permeability of the bed in the sintering grate, avoiding excessive fuel consumption and producing a quality sinter. The aim of this project is to use some of the methodologies for determine the saturation degree on ores and coal to determine the optimal moisture for sintering. In the sinter pot grate series, 3 to 4 assays in a series of 10 are required to determine the optimal moisture for the process. The saturation degree curve test has shown that is really viable to use this technique to skip those tests and go directly to the series to determine productivity and the coke / anthracite consumption. In an industrial scale can be used to adjust the water addition in the conventional mixing methods used in the sintering plants to increase productivity in the process.INTRODUCTION Sintering Sintering is a high temperature agglomeration process in which iron ore fines are partially melted and bonded together using fluxes and a source of fuel, usually coke breeze. The agglomerated product, sinter, has improved metallurgical properties making it an ideal ferrous burden that enable the passage of hot gases in the iron-making blast furnace. The sintering process is normally carried out over three basic stages: granulation, ignition/sintering, and product sizing. In the granulation stage, iron ore fines (usually a blend of selected ores), sinter return fines, fluxes and fuel, and are mixed with water and micro-pelletised in a drum or disc before being introduced in the main granulation circuit. (Wang, Teng, & Wang, 2017)."

Jan 1, 2018

By Érica Linhares, Anderson Silveira Lopes, Aline Costa

In the production units of ferromanganese alloys wastewater are generated. They mainly arise from gutters of drainage water from warehouse of raw material (manganese ore, reducing agents and other), product and slag. This wastewater, in general, may contain particles that will suffer difficulty to naturally decant, giving the water turbidity and color characteristics. Thus, this study aims to characterize the effluent, the treated water and the sludge from the sedimentation tank from the one main Brazilian plant. The investigated characteristics were: turbidity, total solids (TS), suspended solids (SS), dissolved solids (DS), pH, Eh, COD (chemical oxygen demand), residue classification and chemical analysis by ICP - OES. The turbidity before treatment was 417 NTU and after passing through the tank, 44 NTU, a figure slightly higher than the emission standards for Class 1 regulated by the Brazilian environmental legislation in force. The values for TS, SS and DS of the effluent were 225, 114.3 and 110 mg/L, respectively. For the treated water the values were 93, 48.3 and 45 mg/L for TS, SS and DS, respectively. The sedimentation process was able to reduce by 21 % of the COD. In the test of loss on ignition (LOI) from the tank bottom sludge were observed losses of 29.35 %, while the volatile analysis found 20.70 % of volatiles in the sample. It was determined that the concentrations of Al, Fe, Mn and S are, respectively, 0.1875 mg.L-1, 0.3071 mg.L-1, 0,789 mg l-1 and 0.00828 mg.L-1, values above the maximum allowed by law. Based on the analysis of X-ray diffraction, the identified minerals in the sludge were quartz, muscovite, kaolinite, calcite and albite.

Jan 1, 2014

By Mario Gerards, Marco Steinberg, Jan Huben

"Wet high intensity magnetic separation or WHIMS is a widely used technical process for the recovery of magnetic susceptible iron ore particles, mostly for fine and ultrafine grain sizes. The JONES® WHIMS - Wet High Intensity Magnetic Separator, has been used for many years and in countries all around the world. This paper outlines the physical principles utilized for the separation inside the unit, as well as some of the recent changes and developments on the design. It will also give an outlook on the theoretical potential of different alternative yoke materials. The aim of this paper is to analyse the suitability of different yoke materials to improve the equipment. This will be done comparing the magnetic and mechanical parameters and analysing availability and price to find the best compromise regarding cost and benefit. As far as the different kinds of materials are concerned, a special material has been identified as suitable during the comparison exercise. After running the economical calculations, especially with respect to the reduction of the total power consumption of the equipment, a tremendous reduction of the total power consumption has been determined. In addition, to the theoretical exercises and due to the promising results of the same, the Pilot Unit P 40 of the JONES® WHIMS has been manufactured with the special material in order to get practical results as well. Finally, this paper outlines the theoretical and practical results focused on the power consumption. The results are showing that the total power consumption can be reduced tremendously. Hence, the way for a new generation of JONES® WHIMS - environmentally friendly - has been paved."

Jan 1, 2014

By D. Saramak

"High-pressure grinding technology is considered as one of the most efficient techniques of ore comminution, especially in terms of energy consumption. HPGR devices has been utilized in many mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Even though the technology well known (introduced into mineral processing circuits in 80’s), there are still examples of ineffective operation of HPGR devices. This is a result of improper application of HPGR into individual crushing circuit. The purpose of the paper was to analyze selected effects achieved in HPGR on the course and effectiveness of beneficiation operations. Investigations were carried out for copper ore, and investigative programme was run for different values of HPGR pressing force, as well as changeable ore characteristics (content of fine size fractions, material moisture). All crushing products were then treated in flotation process, in order to determine useful mineral recovery. Results of investigations show that HPGR operating pressure influences the metal recovery in proportional way, however too extensive pressure values have relatively lower impact on increasing of the metal recovery. Particle size distribution of HPGR feed and its moisture have lower influence on recovery level than HPGR pressure, but too extensive moisture content influences the higher energy consumption of the roller press, together with less effective comminution. The second aspect raised in the paper was a possibility to control and optimize the HPGR-based circuit. There were presented the proposed approach to adjustment of HPGR operating parameters that enables the higher metal recovery.INTRODUCTION The high-pressure grinding technology, invented and developed by Professor Schoenert in 70’s (Schoenert, 1979), is currently regarded as one of the most efficient methods of hard ore comminution. Since then the technology was introduced into raw materials treatment circuits in many mining and mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Considerable number of works concerning modeling and optimization of HPGR operation were also presented (Daniel & Morell, 2004, Tavares, 2005, Saramak, 2012, Saramak & Kleiv, 2013). Nowadays high-pressure grinding rolls devices are considered as well know technology with over 500 sold machines, according to various sources."

Jan 1, 2018

By Luis G. Bergh

Today, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design. In this work, a model of a rougher flotation circuit, based on operating variables and parameters fitted from industrial data, obtained in some previous work, is used to develop a set of logic rules in order to aid operating decisions. The simulator was first used to sensitize the effect of changing the froth depth profile on target variables, and then to find out the best profile to reject common disturbances coming into the plant. The flotation circuit simulator was redesigned to incorporate an expert system following the proposed control algorithm. Several tests were performed to evaluate the control responses to different correlated series of input variables, such as feed grade, tonnage, particle size distribution, and solid percentage. Control alternatives are discussed based on the circuit simulator. Keywords: modeling, industrial data, flotation control, mineral processing.

Sep 1, 2012

By M. L. Liu

This work reports the results about the determination of mean activity coefficients and relative partial molar free energies for copper sulfide mineral bioleaching solutions by potentiometric method at 25ºC. The experimental potentiometric data were obtained by combining a solid state membrane-cupric ion selective electrode (Cu2+ ISE), containing a KNO3 filling solution, and an Ag/AgCl electrode. The measurements were performed in different series of copper sulfide mineral bioleaching solutions. The non-ideal behavior of the system was described on the base of the Pitzer ion-interaction model for mixed salts. Meanwhile, the relative partial molar free energies of bioleaching solution were investigated. The determination of the thermodynamic properties offers a basic data for the study of copper sulfide mineral bioleaching solutions.

Jan 1, 2014

By J. Leite

In a small-scale mining in Brazil?s northeast, scheelite were exploited since 1940?s using a traditional gravity concentration flowchart (composed by jigs and shacking tables) that operates with low efficient for fine particles. Tailing of this plant was submitted to chemical, mineralogical and size characterization. Results pointed 50% smaller than 74µm with a grade of 0.11% WO3. The particle?s size is an important operational variable to heighten recuperation by shacking tables. Tests using Falcon SB40 centrifuge concentrators and shacking table were realized, optimizing their operational variables. Based on the tests results a new flowchart was proposed for concentrating and tailings recovery.

Sep 1, 2012

By C. R. Mambote

Vanadium is an important metal that is used mainly in ferrous and non-ferrous alloys due to the high tensile strength, hardness, fatigue resistance and corrosion resistance. Vanadium consumption in the steel industry represents about 85% of the vanadium-bearing products produced worldwide. The primary sources of the metal are patronite, roscoelite, and mottramite. Vanadium has also been produced as a by-product of the uranium production program which uses carnotite ores as a source of uranium. Vanadiferous magnetite iron ores are used for producing vanadium as well. In addition, it is known that vanadium can be recovered from the ashes of crude oil and petroleum coke. The process for treating boiler residues, fly ash and petroleum coke is similar to the process used to treat spent catalysts and ores. However, some of these materials may contain high carbon that must be removed at specific stage of the operation. Several processes are available for obtaining vanadium from fly ash, such as roasting vanadium bearing materials in the presence of sodium salt. The salt roasted calcine is subsequently leached with an alkaline or acidic solution. To obtain a cal-cine from which the vanadium can subsequently be recovered, the carbon in the source materials has to be eliminated prior to the roasting process. Other processes use the conventional hydrometallurgical route, in which fly ash is leached with sulphuric acid to obtain an impure vanadium pentoxide. The impure vanadium pentoxide is then treated with a sodium carbonate solution under atmospheric conditions to subsequently precipitate vanadium as ammonium metavanadate. Actually, the salt roasting process is the only process used commercially. In the present study, the progress in the technology of vanadium extraction from secondary materials is reviewed. The perspectives and the challenges for new process development are discussed.

Jan 1, 2014

By M. Zolghadri

MIBC and sodium metasilicate are used as a frother and a dispersant in coal flotation respectively. In order to study interaction between them, flotation experiments were performed on fine coal (<150 microns). It was found that if the frother (MIBC) dosage is in excess of a certain limit, it has an activation effect on the gangue minerals associated with coal. In addition, it was found that however sodium metasilicate can disperse clay slimes eliminating slime coating, but in the case of excess dosage, could intensify activation effect of MIBC, which is undesirable in coal flotation. Keywords: coal flotation, sodium silicate, frother, dispersion, activation

Sep 1, 2012

By P. Khattri

At Tata Steel, Coal is washed in gravity and froth flotation circuit at 13-15 mm size and below. Being coal is high in ash (~35%) and difficult washability characteristics (having high (~40 %) NGM at desired ash levels) needs more and timely quality data of ROM for effective optimization and process control. Conventional approach of supplying quality data takes 4-5 hours time. This means during this period, it is assumed that coal is having similar characteristics as of previous set and it is not possible to fine tune during this time which resulted in yield loss. Hence producing clean coal on agreed ash value consistently is a challenging task because of high NGM and variation in input quality. To overcome the problem of collection of representative sample and timely result a new technology was adopted Prompt Gamma Neutron Activation Analysis (PGNAA) technology which is basically an online analyser using Gamma rays as the source to measure the ash content in coal running on a conveyor which gives real time ash analysis. The details of this technological intervention are discussed in details in this paper. Keywords: near gravity material, PGNAA

Sep 1, 2012

By J. Zou

With the increasing applications of the Chinese metal magnetic liners, the requirement for their technical specifications has become stricter and stricter. It is necessary to deeply analyse the metal magnetic liners in order to improve their reliability and economics. The key issue of metal magnetic liners is magnetic forces: their attractions to mill shell and protection layer. Mathematical models were developed using finite-element analysis software and systematic simulation analyses of the two most critical indexes of magnetic liners were performed to find out the most important parameters and their effect on the liner?s characteristics. The relationships between magnetic forces and installation gaps, thickness of permanent magnets and thickness of protection layer may be used to guide the design of metal magnetic liners for ball mills in order to achieve good economic indexes.

Jan 1, 2014