Search Documents

By Arkady Senchenko

The application of centrifugal separation methods with the use of gravity concentrators has been assigned high priority while gold-containing minerals processing. The separation proceeds under centrifugal force resulted from the rotor spinning and wash water flow in the concentrators. The high specific gravity particles are retained at the trapping surface of the cone, and the low specific gravity particles are brought in the tailings. The centrifugal field in such concentrators (Knelson, Falcon) is generated by the rotating cone provoking the swirling of the free fed slurry flow. The author investigated the regularities of the separation process in the centrifugal gravity concentrator where a two-phase flow of the separated mineral media is under the pulsed pressure of the fluidization water and air. As a result of the study the possibility of the deeper penetration of the fine heavy fraction into the cone rings, providing the fluctuation of the fluidization water or air flow, was theoretically argued and experimentally proved. This allows the increase of the separation performance at low pulsation costs. The developed mathematical models are in close conformity with the actual process of interest and they enable the prediction of the heavy phase behavior at the isolated process stages in the concentrator. Keywords: gold, centrifugal gravity concentrator, containing, specific gravity, cone ring, pulsation, cost, fluidization water, Knelson centrifugal separator

Sep 1, 2012

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By S. Mitra1

"This study aims to investigate coarse particle detachment mechanisms (particle diameter > 150 ?m) utilising both experimental and numerical technique. Two mechanisms were studied – (i) interactions of bubbleparticle (BP) aggregate with vortices and (ii) coalescence of bubble-particle aggregates. On the first mechanism, interaction behaviour of coherent vortex structures with a BP aggregate (bubble diameter db = 3 mm, particle diameter dp = 0.3 mm) was studied using a CFD model in the Reynolds number range of 100 to 1000. Effect of surface hydrophobicity on the BP stability was examined using a range of contact angle boundary conditions. To address the second mechanism, interactions of bubble-particle aggregate (db ~ 4 mm, dp ~ 0.4 mm) with both free gas-liquid interface and individual bubbles were investigated using high speed imaging. Both rebound and coalescence outcomes were observed to be responsible for BP instability leading to particle detachment.INTRODUCTIONIt is widely known that flotation process performs excellent mineral recovery for base metal ore particles that are typically in the range of ~ 20 to 150 µm in diameter (Jameson, 2010). More specifically, higher recoveries are usually reported for particles in the size range of ~20 to 70 µm while outside this spectrum, generally the recovery diminishes significantly. It would be highly desirable to improve the recovery of particles at the coarse end of the flotation size range spectrum which has significant economic benefit (Jameson, 2010). However, it is essential that insights to particle detachment phenomenon, the primary impediment in coarse particle flotation caused by the underlying hydrodynamic factors are first obtained at a greater depth.In an ideal quiescent liquid medium, due to inertia, coarse particles deviate substantially from the fluid streamlines and collision efficiency with bubbles decreases which can only be augmented by increasing turbulence level in the medium sufficiently to make random physical contacts with bubbles. Nonetheless, even if successful contacts are made, it is difficult for these large particles to remain attached to bubbles in a turbulent shear flow environment. There are two major mechanisms postulated for particle detachment – interaction of turbulent flow structures (eddies) with BP aggregate and coalescence among surrounding aggregates. Earlier work of Schulze (1982) theorised a vortex acceleration component to characterise turbulence effect on BP aggregate instability in flotation machines. Wang et al. (2015) investigated bubble detachment behaviour from a stationary particle in a nearly homogeneous and isotropic flow field. Using PIV (particle image velocimetry), it was shown that the local maximum energy dissipation rate for the case of bubble detachment was significantly higher than the no detachment case, and was also higher than the critical value for bubble detachment calculated using Schulze’ theory (Schulze, 1982). Later, Wang et al. (2017) also visualised the BP aggregate instability in a cavity flow leading to particle detachment which was attributed to bubble coalescence, bubble surface oscillation and particle deceleration phenomena."

Jan 1, 2018

By Dilip. Makhija, Asim. K. Mukherjee, Tamal Ghosh, Abhay Patra

In India around 15-20% of Run of Mine (ROM) from any iron ore deposit reports to slime dams as byproduct of iron ore beneficiation process. The proportion of iron ore slime to ROM will increase in future with higher proportion of lean grade ores in ROM. Furthermore, tonnages of iron ore slime will also increase with increasing demand of iron concentrate. Presently, this slime is stored in the dam in the absence of beneficiation technology. A beneficiation flowsheet has been developed at Tata Steel. This process produced concentrate of 2.2% alumina with 40 % yield from slime of 7-9% alumina. The iron content in the reject will be less than 40% thus adhering to the regulatory norm. Pilot scale study show waste from slime beneficiation is a good raw material for making a variety of building materials. Waste from slime beneficiation also has soil amendment properties. Pilot scale studies show productivity of rice increased when the waste of slime beneficiation process is mixed with soil. On commercialization of this zero waste technology slime generated from the iron ore washing plant will be completely used. In this paper the result of the pilot scale studies on slime beneficiation and utilization processes towards soil making and making of building materials are discussed in detail.

Jan 1, 2014

By C. Abbruzzese, F. Vegliò, S. Ubaldini, R. Massidda

The aim of this paper was to study the influence of different water/organic solvent mixtures (isopropyl alcohol, ethanol and ethylene glycol) on the gold desorption process. The experimental work was carried out on laboratory scale, using activated coconut carbon with different temperatures and extraction times, without adding cyanide. Best results have been obtained in this order: isopropyl alcohol > ethylene glycol > ethanol. Starting from gold concentration of about 5 g Au per kg of carbon, best kinetics resulted in 97-100% of gold extraction, after 8 hours of desorption, at a temperature of 80ºC.

Jan 1, 2003

By L. X. Zhang

It is very important to improve the A/S of the bauxite to keep sustaining development of Chinese alumina industry. This article summarized the issues of several desilication technologies, which are named as normal flotation, reverse flotation and bi-flotation. Normal flotation has been got industrialization because of technologic advantages. The campaign experiment of reverse flotation which has principle advantage was carried out in 2004, and bi-flotation which is combined the advantages of both the normal flotation & reverse flotation has the most attractive future. The development of bauxite flotation will be focused on multi-utilization of bauxite by mineral process technology and corresponding equipment which satisfied with the flotation technology and reagent.

Jan 1, 2014

By M. Canbazoglu

In this study, optimum sulphuric acid leaching parameters of zinc and other valuable metals from two different waelz clinker samples were researched. Origins of the samples are electric arc furnace dust and original non-sulphite zinc ore waelz clinkers. The main zinc mineral determined as zincite in these samples. Collective dissolution of zinc and other valuable metals in waelz clinkers can easily achieved by sulphuric acid leaching of them. 96% of zinc can be dissolved at 80 ºC, 60 g/L sulphuric acid concentration, 60 min. leaching time and 1/5 solid/liquid ratio. Almost 90% of Cd, Cu and Co in clinker dissolved at these conditions while dissolution of Fe was almost 20%. The consumed acid amount for dissolved per ton of zinc is approximately 1.7 tons at these conditions.

Jan 1, 2014

By Bern Klein, Givemore Sakuhuni, Libin Tong

The use of continuous discharge centrifugal concentrators introduced in the early 1990’s for recovery of gold associated with sulphides has introduced a novel application niche for gravity concentration which could not be realized with the low mass yield batch and semi-continuous concentrators. A typical application is scavenging gold associated with sulphides from flotation tails which has potential to increase productivity by reducing gold loss to tailings and lower grinding cost by using a coarser grind. However, the full potential of this technology has not been fully exploited partly due to the lack of reliable small sample procedures to demonstrate applicability. This paper introduces a bench-scale procedure developed to characterize the Knelson Continuous Variable Discharge concentrator (CVD) for scavenging gold from flotation tails. The procedure code named gravity release analysis was derived from standard flotation release analysis. It is a modification of the gravity recoverable gold and gravity amenability test in order to best simulate continuous centrifugal concentration. Based on this iterative procedure, a gravity release index similar to the flotation rate constant, for measuring individual mineral gravity susceptibility for an ore is introduced which can be a useful quantitative measure to both predict application of centrifugal concentration and for plant design. The gravity release analysis procedure was tested on a polymetallic flotation plant tailing at Myra Falls, BC, Canada and results show that it can predict CVD performance. The gravity release index for gold was observed to decrease with each successive cleaner stage showing that the initial stages recover liberated gold whilst successive runs recover gold associated with sulphides and or gangue. The difference in magnitude of the gravity release index for different mineral species shows the species separable by centrifugal concentration.

Jan 1, 2014

By Özcan Y. Gülsoy

Coal beneficiation with optical sorting has not yet been studied in detail. Optical separation of coal from gangue particles as a dry method can be used as an alternative to the other enrichment methods. Developments in optical and pneumatic technology put the optical sorting one step forward by means of applicability of the mechanical sorting to the mineral industry. Because of the inefficient separation performance, dry separation of coal is very limited in industrial applications. Therefore, optical sorting depending on color differences between two minerals can be introduced to coal beneficiation systems. In this study, coal samples obtained from Konya-Ilgin region (Central Anatolia-Turkey) were separated by optical sorter and the results were evaluated. The conventional floatability tests for Ilgin coal are conducted by collecting most of the feed material at 1.3-1.4 g/cm3 density range. Separation of Ilgin coals with heavy medium methods will not be possible because of poor density difference between coal and its impurities. There are important color differences among the floated particles at 1.3-1.4 g/cm3 density range. Therefore, Ilgin coal is subjected to optical sorting in a pilot scale optical sorter. Different size fractions were fed to the optical sorter and then rejected and accepted particles by equipment were analyzed. Ash content of the accepted particles was reduced to 25-35 % and ash in tail increases up to 55-60 % after sorting. Although most of the material floated at low densities, optical sorter separated the feed into two different quality products. This study has the potential to clarify applicability of optical sorting even to non-floatable coals and to provide an important contribution to both industrial applications and literature.

Sep 1, 2012

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014

By Sunil Tripathy, Y. Rama, Srinivasulu. A., Amit Ranjan

Process improvements in an operating plant are always challenging. Mineral beneficiation plants based on gravity concentration techniques need continuous evaluation and monitoring of its processes for getting maximum recovery and better grades. But, in an operating plant it is very difficult to control all the parameters due to numerous reasons such as unsteady operation, fluctuation in the quality of run-off-mine ore, overall flow rate etc. For better understanding of the beneficiation circuit, it is necessary to evaluate the critical operating parameters which affect the performance in terms of grade, recovery and throughput including losses of valuable materials into tailing. Accurate data collection and proper data interpretation followed by making necessary change which is implementable in an operating plant play very critical role in performance of the circuit. In case of gravity operated beneficiation circuits of chrome ores where the quality of the feed and physical parameters varies continuously, the operators are required to modify the critical operating process parameters on continuous basis which is very difficult and tiresome. There are many causes of the data variability, including both error (sampling and assay), and real variation in performance due to changes in ore mineralogy, operating conditions and other factors. In this article, attempts made to evaluate the performance of ultra-fine beneficiation circuit in terms of silica reduction in the concentrate of chrome ore beneficiation plant (COB), India are discussed. The approach adopted and practical problems encountered during the study were also discussed. Results obtained from plant audit based on the above methodology has shown that SiO2 content in the concentrate can be reduced to <4%.

Jan 1, 2014

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014

By C. Suazo, O. Alruiz, A. Hofmann, I. Fernandez, W. Kracht, N. Mora

"Compañía Minera Dona Inés de Collahuasi, CMDIC, has developed a methodology that allows estimating economic benefit taking into account the variability of the ore characteristics (geometallurgical models). Currently, the grinding model allows predicting the treatment capacity, specific power and balls consumption for short, mid and long term planning. An alternative impact test to estimate SAG grinding parameters is presented in order to bring the geometallurgical model from mid and long term to short term planning. The impact test uses either the production bench or geological drill holes. This allows Geologists increasing the density of grinding parameters within the block model improving the geostatistical estimation of the rest of the blocks. The test requires a small amount of sample to obtain the requires grinding parameters for the grinding model in comparison to the well known grinding test and also, it can be performed easily and quickly by the geology team of a mining company. The alternative grinding test is presented in this article. The grinding model using this short grinding test has been successfully used in mining planning and the accuracy of the model is demonstrated using monthly average instantaneous throughput from January 2013 to March 2014, showing an average relative error of 5% and an R2 value of 0.9. Also, 111 individual variability samples were divided into two each, in order to compare the estimated grinding parameters based on this alternative test to the grinding parameters obtained from the conventional grinding test. The comparison shows an average relative error of 4% and an R2 value of 0.9."

Jan 1, 2014

By N. T. Beukes, W. Banda

Recovery of Co from slag is a recent advancement in the extractive metallurgy of nonferrous metals. In this study a DC arc technology at laboratory scale has been applied to investigate the selective recovery of Co from slag, under three different flux types with an emphasis on influencing the activity of FeOx, SiO2 and CoO in the slag. It is known that reduction of slag by carbon is only up to a certain level after which, the recovery will depend on the chemistry of the slag, hence the need to modify the slag chemistry. Two power settings were employed to induce higher temperatures and aggressive agitation. The results were interpreted by comparing how much Co and Fe was in the slag and alloy. TiO2 reduced the amount of Fe in the product alloy compared to when CaO and CaF2 were used. The change in power did not seem to have had a major effect on the recovery although the amount of material lost to flue dust was more at a higher power rate.

Jan 1, 2003

By Paul W. Cleary

"DEM application in mineral processing has for many years been heavily focused on simulating mills of various types. This method can be used to simulate many other aspects of mineral processing operations and can be used both to enhance understanding of the underlying flows and of issues such a breakage, wear, blockage, product degradation, segregation and mixing. The application of DEM to four important classes of non-comminution problems and equipment commonly found in or near mineral processing plants are described. These are:- Particle transport (examples include a conveyor belt and an inclined screw conveyor)- Sampling (assessment of sample bias for cross-stream samplers)- Separation (the efficiency of vibrating screens)- Storage and reclaim (discharge from a multi-port hopper and segregation in a splitter bin with asymmetric ingoing and outgoing conveyor belts, apron feeders and impact plate)."

Jan 1, 2003

By Reuter M. A., R. D. van der Weijden, W. F. C. van Wageningen

"Copper(II) can be recovered or removed from acidic copper sulfate solutions as cuprite or metallic copper powder by reduction with carbohydrates. The copper powder characteristics, such as size and shape of particles, determine the tendency to adhere to reactor walls and to agglomerate. In order to make this process suitable for a commercial scale pipe reactor, process conditions and the reactor configuration were varied in order to influence the copper characteristics in a positive way. The aim was to achieve proper particle throughput in the pipe reactor and to obtain a well defined copper powder.In this paper the effect of both, chemical and physical parameters on the shape and size of particles were systematically studied in a number of autoclave experiments. These parameters include mixing, Cu(II) concentration, pH, temperature, seeding, use of additives and reactor materials. Additionally, Monte Carlo simulations of copper growth inside a Kenics static mixer were made. Results show that the use of additives and the use of static mixers influence particle characteristics the most."

Jan 1, 2003

By V. Panayotov

Flotation practice usually uses the Sheridan-Grizvold selection method, where zinc minerals are activated by addition of copper sulphate and depressed by addition of sodium cyanide, ferrous sulphate, zinc sulphate or various mixtures of these reagents. The method is suitable for the flotation of sulphide ores, which, do not bear precious metals, such as silver and gold. When classical technology with cyanide is applied to depress zinc minerals, the precious metals, which are contained mainly into lead minerals, are dissolved into the solution, which represents a technological loss. In order to avoid this process, we have made use from the knowledge on the semiconducting properties of lead and zinc sulphide minerals. We have changed the surface charge of minerals by means of an electrochemical impact realized by direct current application and specially designed set of insoluble or semi-soluble electrodes. Thus, flotation separation of lead and zinc sulphide minerals was achieved, at increased recovery of lead, zinc and silver. The technology proposed was implemented in a Bulgarian flotation factory; it worked over 5 years providing significant, positive economic, technological and environmental impact. Silver recovery was increased by 0.8-1.0 %, and lead and zinc recovery was increased by 0.8-1.0 %. The technology is easily controllable and adaptable to raw materials and parameters of the technological process. It can be paid back for 6-8 months after the implementation. Keywords: lead-zinc flotation separation, electrochemical impact

Sep 1, 2012

By P. K. Fedotov

Annually at least 5% percent of world power consumption is involved in the process of ore dressing while ore processing technology. Such rate of energy consumption demonstrates the importance of a given process study in the human life-sustaining activity. Examining of interparticle destruction being under external stress pressure in ore responses this problem solution at the greatest degree. The technology of destruction in the roll press is of great interest. The use of the given equipment allows to save a significant amount of energy by means of the built-in ore destruction mechanism. Examination of stress-strain fields which determine the level of interparticle destruction between the rolls in the ore layer enables to specify both level of ore destruction and power consumption. The mathematical computer modeling for the deformable environment use based on the finite-element method (FEM) allows to carry out the given research. We use FEM solution for elastic contact problem for the most complete study of power consumption employed in ore and interparticle destruction. This problem solution allows also to examine energy consumption expenses spent for ore crushing in the roll press. Also we have identified the mechanism of ore in a layer of the particles under pressure roller press. It is established that high level of performance and reduction of energy consumption in interparticle destruction of ore in the layer due to the appearance of the gradient of normal stresses in contact of particles of mineral raw materials. The algorithm has been developed determining crushing product particle size distribution of fractured particles in the layer, using the Bond’s theory of crushing. The use of our FEM model reduces the time of equipment selection for new plant and at the design stage to reduce the risks of errors in the choice of roller presses.

Jan 1, 2018

By Komar Kawatra, Joseph Halt

"Bentonite clay has been the traditional binder for iron ore pellets. However, bentonite increases pellets’ silica contents and is expensive. Researchers have proposed lowering bentonite doses by mixing it with other common binders. These mixtures may only be successful if the fundamental bonding mechanisms are understood. For example, what happens when bentonite (physical bonding) is mixed with fly-ash (chemical bonding)? What happens when bentonite is mixed with cornstarch (physical bonding)? In this paper, experiments are described where bentonite was mixed with various ratios of cornstarch and fly-ash, and pellets were agglomerated using 0.66 % w/w binder. Ca(OH)2 and CaCl2 were added as activator and accelerator, respectively, to the bentonite-fly ash mixture. Curves of pellet dry strength vs. bentonite-starch ratio were linear, suggesting the physical-physical bonding mechanisms were compatible - acceptable strengths (> 22 N) were produced at all bentonite-to-starch ratios. This was contrary to bentonite-fly ash mixtures, which displayed dry strength curves with a noticeable minimum due to competing binding mechanisms. Bentonite alone and fly ash alone produced acceptable strengths (> 22 N), but their mixtures resulted in weak pellets. Due to the positive results using cornstarch (CS) binders, the effects of CS solubility in water were investigated using two CS with high and low solubility (60 and 7.5 %). CS was premixed with bentonite at various ratios (0, 20, 40, 60, 80, 100 %). Pellets were agglomerated using 0.66 % w/w binder. The dry strength of pellets ranged from 50-300 N using the high solubility CS mixtures, and from 50-85 N using the low solubility CS mixtures. Fired strengths exceeded 2200 N/pellet at all bentonite-cornstarch ratios. This research showed that cornstarch solubility is an important factor in determining its effectiveness as a binder for iron ore concentrates, but significant work is still necessary before it can be used as a bentonite replacement."

Jan 1, 2014

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003