Search Documents

By Morin D. H., Battaglia-Brunet F., D'Hugues P.

"In the mineral-processing field, bioleaching of metal sulphide concentrates is currently operated in very large mechanically agitated tanks. Such bioreactors have considerable requirements in terms of power consumption for mixing, aeration and heat transfer. The use of slurry bubble column, where the particles are suspended by gas motion as well as by liquid upward flow, could be an alternative to achieve bioleaching in more economical conditions. In order to compare these two techniques, a unit of stirred reactors in cascade and a bubble column were comparatively operated at laboratory scale in the bioleaching of a pyrite concentrate. For both pieces of equipment, experiments were performed not only in batch mode but also in continuous conditions.Bubble column performances were significantly affected by unpredictable technical difficulties met to maintain continuous feeding in the bubble column and by a significant settling of the heavy solid particles. Nonetheless, theoretical kinetic data, extrapolated from results in batch conditions, could be compared to those obtained in continuous tests, in bubble column and in mechanically agitated reactors. These kinetic data were used to evaluate the influence of reactor design and configuration choice on bioleaching performances."

Jan 1, 2003

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012

By Stephen Simukanga, Jewette Masinja

"Mining has been going on commercially in Zambia for over 100 years. The backbone of the mining industry has been copper production and its by-products of cobalt and gold. Over these years, the mining industry ownership structure has swung from private ownership to state ownership in 1972, and back to private ownership in 1995. Environmental management was first introduced into the body of Zambian legislation in 1991 through the promulgation of the Environmental Protection and Pollution Control Act (EPPCA). The Act’s main functions included the protection of the environment and control of pollution, and in particular to provide for the health and welfare of the people, animals, plants and the environment in general. This Act, was replaced in 2011 by the Environmental Management Act (EMA). The new Act has a number of new elements including: mainstreaming environment in national planning, it provides for the domestication of multilateral environmental agreements, enhances public participation issue, creates a central environmental information depositary, elaborates access to information principles, establishes an environment fund, creates enforcement orders, provides for both Zambia Environmental Management Authority and members of the public to sue for damages following environmental pollution, and provides for the appointment of honorary Inspectors. In addition to this, the Mines and Minerals Act of 1995 provided, for the first time, a section on environmental management in the mining sector. This section also created the Environmental Protection Fund (for mining), and made it obligatory to undertake environmental impact assessment before mining permits could be issued. The Environmental Protection Fund has now been established, as provided for by the law, and currently has more than USD9.0 million in the account. Secondly, environmental auditing is now being carried out annually on mines around the country, the effect of this has been a significant improvement in the environmental management of mining in Zambia. This paper looks at the response of the Zambian mining sector to these pieces of environmental management legislation, and the direction that the mining sector is expected to take on environmental management going forward."

Jan 1, 2014

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By F. Henríquez

Traditionally, the implementation of an automated control for a ball mill has been a challenging one. First, it must be capable of processing a variable SAG mill feed while at the same time avoiding to become a process bottle neck. Second thing is, it must deliver an adequate quality product (P80) to the process downstream. Then the ball mill itself and its associated classification equipment has problems of its own: it must maintain adequate control of cyclone?s pressure, density and pump-box level with often, less manipulated variables than needed, namely, variable pump speed and the opening/closing of cyclones. Thus, it becomes a non-linear multi-variable type of process with often too multiple and contradictory control objectives to satisfy simultaneously. On top of that, to extend cyclones availability and yet, maintaining their performance, is must both for process and maintenance purposes. Trying to solve the puzzle, Minera Los Pelambres implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control in two of its newest ball mills, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Because of their differences in processing capacity, size and topology, two different stabilizing-control strategies were developed, tested and tuned. Hence, for both control approaches their implementation process, main results, areas of applicability, limitations and their key performance indicators are discussed further. This paper also discusses the need of such advance control technologies in the mining industry, including the impact of these technologies on best practices for their implementation, operation and long term sustainability

Sep 1, 2012

By T. Leißner

This contribution deals with the mineral processing of Li-silicate greisen-type ores comprising of quartz, topaz and zinnwaldite (lithium-rich mica). The origin of the greisen-type ores processed is the Ore Mountains(Germany) where it is explored as a potential resource for the production of lithium carbonate. The goal is to develop a process chain for the enrichment of zinnwaldite using dry techniques only. As basis for the investigation the process chain, which historically was used to process the greisen focused on cassiterite and wolframite, is taken and modified towards the zinnwaldite. Starting with crushed material with particle sizes smaller than 35 millimeters, investigations on different approaches to grinding to liberate mica from gangue are carried out. Concentrates of zinnwaldite are then produced by magnetic separation of size fractions. To assess the success of grinding, classification and separation, mineral liberation analysis and atomic absorption spectroscopy are used. The amount of lithium measured in the sample with atomic absorption spectroscopy was used to calculate the content of zinnwaldite based on its known mineral chemistry. Combined with the particle size distributions, product qualities are determined. Altogether, this allows the thorough evaluation of the success of comminution with focus on following steps of concentration. Keywords: lithium, zinnwaldite, magnetic separation, mineral liberation analysis

Sep 1, 2012

By Fedotov Pavel

One of the efficient means of ore disintegration during the processing is its volume breakage in such machines as roller-presses. Up to date neither the ore disintegration mechanism in roller-presses nor the reasons of their high efficiency are thoroughly investigated. In this work, the mathematical model of Finite Element Method of bad material disintegration in roller-press is discussed. The mechanism of the interparticle ore disintegration is traced.

Sep 1, 2012

By Mario Gerards, Sergej Podkow, Marco Steinberg

"The JONES® WHIMS technology is based on the magnetic separation process and is widely used for the recovery of magnetically susceptible iron ore particles. The conventional machine design is well-known within the iron ore beneficiation industry for more than 50 years and recognized to be highly reliable, robust and extremely compact with the advantages of high capacity and selectivity. In 1981 Rana Gruber AS, Norway bought 14 JONES® WHIMS DP 317 separators when the magnetic separation plant was built and erected. Today, 11 of these old machines are still operating profitably and efficiently. The former supplier was the coal and minerals division of Klöckner-Humboldt-Deutz (KHD) which is today MBE Coal & Minerals Technology GmbH (MBE). This paper outlines a detailed description of the project of revamping the above mentioned old machines and describes the challenge of incorporating enhanced and newly developed technology into an existing processing plant. Further it gives an overview of the recent developments on the design of the JONES® WHIMS. In order to meet modern product requirements and to increase and secure plant productivity, in 2012 Rana Gruber AS settled a contract covering two new designed JONES® WHIMS DP 317 HFR separators to be implemented into the existing building and the upgrading of all 11 older JONES® WHIMS under the use of as many refurbished items as possible. The two new machines were fully developed by the product specialists of the supplier in cooperation with the operator Rana Gruber AS, thereby taking advantage of their great experience. The design of the new machine is based on the conventional design, i.e. the general operating mode as well as the overall dimensions are identical. Finally this paper gives an overview about the erection and commission phase of the two new machines and gives a detailed comparison between conventional and enhanced WHIMS technology."

Jan 1, 2014

By Marianella Perez, Williams Calderón, Gonzalo Montes-Atenas

The lack of fresh water sources, particularly in the Northern part of Chile, has driven the mine sites to search for new and sustainable paths to obtain water resources to run minerals processing operations. Among them, the use of seawater in concentrators appears as an interesting solution to this problem. However, the presence of seawater will have an impact onto the operation, not only because it will enhance corrosion reactions in the equipment installed in a plant, but also because it may affect how particles will effectively be processed across the numerous unit operations existing in the mine site. Among such unit operations, the grinding stage is a highly regarded as it defines the success of the separation of valuable minerals from gangue material in the froth flotation operation. Then, one important aspect to be addressed is to understand how the presence of seawater will affect the different mechanisms acting during the operation of a ball mill. The aim of this research work is to assess the effect of changing the aqueous matrix from process water to seawater in ball mills onto the mill performance. The methodology considered the use of Fluent® software and its capabilities to run numerical simulations with heterogeneous media. On one hand, from the data analysis, it is possible to infer that breakability mechanisms should not be significantly affected. On the other hand, the high ionic strength of the matrix should impact importantly particle transport mechanisms within the mill. Particularly, when transporting finer particles. Rheology results were in agreement with previous published research studies suggesting the suspensions to behave as Newtonian, Dilatant o Pseudo-plastic fluid depending on the amount of fine particles present in the grinding media. The latter will result in changes in the residence time of particles in the mill producing overgrinding or an excess in the circulating loads.

Jan 1, 2014

By V. A. Ivanova

Modification of hydrophobic part of carboxylic collector molecule is an upcoming trend for producing new reagents and changing its flotation properties such as activity, selectivity, sensitivity to hardness salts that inevitably present in the pulp liquid phase in the processing of ores containing calcium minerals. A wide range of apatite collectors ? monoalkyl ethers and monoalkylamides of dicarboxylic acids ? succinic, o-phthalic and maleinic acids have been synthesized by the addition of aliphatic alcohols and amines with various hydrocarbon radical value (from ?11 to ?16) to anhydride of the corresponding acid. Using computer modeling based on ChemBio 3D program of specialized complex Chem?ffice the calculation was carried out of charge distribution on atoms, energy parameters of molecules for investigated compounds. Calculated values of absolute hardness (?=6.75 ? 12.36) and absolute electronegativity (?= 5.67 ? 8.90) of the reagents showed that monoderivatives of dicarboxylic acids refer to the ?hard? type of bases. The degree of a charge transfer during calcium compounds formation of considered collecting agents (?N=0.009 ? 0.143) has been computed. Dissociations, micelle formation in solutions of these reagents and its hydrophobic and collecting properties were investigated in respect to apatite. Dependence of bulk, surface and collector properties on collector molecule architecture (double bond or benzene ring and non-ionogenic functional group in the structure of hydrocarbon radical) has been established. It is shown that experimentally determined dissociation constants (??a=5.16 ? 5.60 for succinic acid derivatives and ??a=3.32-3.78 for maleinic and o-phthalic acid derivatives) perfectly correspond to acidic properties predicted by computer calculations. Compounds of monoalkylderivative dicarboxilic acid have been determined optimum in composition and structure. The results of apatite flotation from apatite-nepheline ores of the Khibiny deposit (the Kola Peninsula) are presented here and show benefits of selected reagents. Keywords: monoalkylderivatives, dicarboxylic acids, reagents, microflotation

Sep 1, 2012

By Weiran Zuo, Emmy Manlapig, Fengnian Shi

The effect of metalliferous grains on electrical comminution efficiency was investigated by comparative experiments using natural rocks and synthetic samples. The result indicated that the existence of metalliferous grains affects the breakage probability and product size distribution of electrical comminution. On average, metalliferous grains increased the breakage probability of particle in the first pulse discharge by 55% and generated finer product at the coarse end. As a result, particles with metalliferous grains exhibited higher energy efficiency than that without metalliferous grain in electrical comminution. A positive linear relation between product fineness and specific energy in electrical comminution was observed. With the assistance of numerical simulation on the electrical field distribution of ore particle, the role of metalliferous grains in electrical comminution is confirmed and the mechanism of metalliferous grains effect is elucidated. Understanding of the effect of metalliferous grains on electrical comminution is important to evaluate the feasibility of applying electrical comminution to ores with different mineral composition, and to understand the breakage behavior in electrical comminution.

Jan 1, 2014

By S. Narra

The importance of bio-products production is enhanced with the abundance and renewability of ligno- cellulosic biomass in comparison to the depleting fossil fuels especially in producing environment friendly energy. Lignin is obtained as a sludge residue from the pulp and paper industries as well as from the bio- ethanol /bio-gas production plants. Lignin is a renewable fuel with a high heating value equivalent to anthracite coal, low ash content and hydrophobic properties. The extracted lignin in paper and pulp mills is usually burnt at the mill directly to cover the energy production costs of the mill. The efficient utilization of lignin can reduce the percentage of lignin sludge used for energy production in comparison to the present situation. Presently the lignin is burnt /incinerated as sludge with minimum of 30 to 50 % moisture content. This high moisture content reduces the energy efficiency and simultaneously utilizes more amount of lignin sludge in producing the required energy. This paper explains a possibility of integrating sludge-pelleting techniques in paper and pulp mills. The integrated sludge-pelleting techniques would lead to an optimal utilization of lignin for energy and would simultaneously save the lignin resource for material utilization. The sludge pelleting process solves also the problem of handling, storage and explosion risks of lignin when compared to the present situation.

Sep 1, 2012

By P. M. Solozhenkin

"Galvanochemical process (GChP)) cleaning of sewages is realized in the field of shortcirquited galvanic elements from the mixture current the materials place in purification’s solution and form multitude galvanopairs without external electric field in presence oxygen of the air. The galvanochemical process is electrochemical process utilizing galvanic pairs: coke - iron, iron - copper and others and process does not require chemical reagents.The effect of basic parameters of the cleaning effectiveness have been studied depending on oxidizing of galvanopairs. Adjusting nature, type of galvanic pairs and forming three component system possible to enlarge emf circuits to 2.378 V.The role of ?2, as basic agent, for generation of hydrogen peroxide and hydroxyl ions.It was stated, that removing of metal ions from solutions occur mainly on account of sorption and hydrolytic sedimentation of iron oxihydrates.Determined separate stages of the process: coagulation, sorptions of admixtures on freshly formed ferric oxides and oxidizing destruction of organic components of effluents in presence of ?2 ? ?2?2. Shown efficiency of the method for removing of Cu, Cr, Ni, Zn, As ions, as well as fluoride, phosphate and cyanide anions and oil products, surface-active and flotation reagents. Cleaned water can be recycled for some processes non-critical toward residual concentration of admixtures, as total salt contents is lowered on 60-75 % and reaching limits of concentration for toxic components.The concept of high power unit creation was developed, and galvanochemical pulsator is presented. The pulsator is not expensive, and exploitation expences are low, as well as servise is simple with high effectiveness, and capacity. The galvanoflotation process is developing, combining galvanochemistry and flotation of hydrofobic admixtures (oil, surface-active agents).The galvanochemical flotators are presented."

Jan 1, 2003

By S. A. Kondratyev

"The present research work aims at disclosing the dependence of flotation concentrate recovery and its grade on the physically adsorbed collecting reagent properties, viz., surface pressure in the reagent film at gas-liquid interface, velocity of reagent species spreading over the said interface, relation between interaction energies of collector molecules within a film and with water dipoles.When using a single collecting reagent it is possible to improve the flotation concentrate grade in two ways, namely, by reducing collector consumption rate or using a weaker reagent. According to the proposed mechanism, a decrease in the physically sorbed species of the collector leads to a decrease in the rate of removal of the kinetic restriction of a flotation contact formation. As a result, the recovery of the useful component is reduced and the content of valuable components in the flotation concentrate is increased. The relationship between the spreading velocity of physically sorbed species at the gas-liquid interface and the recovery and quality of the flotation concentrate has been experimentally proved. Reduction in collector consumption lowered the valuable component recovery at a higher grade of the concentrate.The reasons were established for a rise of valuable content in the flotation concentrate if a weaker collector was used. It is justified that the use of a weaker collecting reagent with a shorter hydrocarbon fragment declines physically sorbed species of collector. The spreading velocity of collector derivatives at gas-liquid interface tends to lower along with less participation physically sorbed species of collector in formation of a flotation aggregate. The spreading velocity is determined for products of interaction between butyl-and ethyl-xanthates and lead nitrate at gas-liquid interface. It is found that the spreading velocity of butyl-xanthate derivatives is higher than that of ethylxanthate derivatives.The research work gets insight into the nature of relation between useful component content in the flotation concentrate and the useful component recovery. It is pointed out that adjusting the collecting activity of a collector makes it possible to influence a useful component content in the froth product thus gaining a compromise between wanted grade and recovery parameters."

Jan 1, 2018

By L. Weitkämper

The big challenge at present and in the future is the economization of resources. This is applied for the whole industry but particularly in fields of mineral processing. The most important resources are energy and water. The shortage and price advance of energy is worldwide noticeable whereas the shortage of water is regionally limited at present. However due to the increasing world population, associated with a rising standard of living, water will become more and more important. Studies of the Unesco from 2001 indicate that the total water consumption raised seven times since the last 100 years at a growth of population of just three times. (UNESCO-Currier, 10/2001). This trend is going to be increased. While today more than 90 % of the humanity has access to clean water, in 2050 just about 50 % will be in the same situation. These figures indicate the importance of a gentle handling with the resource water. Further more the disposal of fine products, containing most of the water, is an environmental concern and in the future the mining and processing of raw materials will become important and necessary in desert, arid or permafrost areas. In these areas just efficient dry cleaning technologies will allow an economical beneficiation or better enable the processing at all. Most of the separation technologies with high throughput rates in mineral processing are based on wet processes. This applies especially for the separation of fines. Though there are some dry technologies available for the separation of coarse materials, like pneumatic gravity separation [air jigs and air tables], magnetic separation and not least sensor based sorters. Dry separation of fines is bounded mostly on cost intensive and low throughput technologies. The pneumatic separation undergoes at present a renaissance, mainly due to the development of the all air jig by the German supplier Allmineral. This newly developed sorting device yields good results in the separation of coarse to medium size material. All these facts and figures show the potential and motivation for developing an efficient dry separation device for fines. The following article delineates the development, performance and chance of a new dry separation technology for fines.

Jan 1, 2014

By Cristiane Ericksson, Ananda Scomazzon, Irineu Schadach, Juliano Tonezer

The state of Rio Grande do Sul, southern Brazil, appears on the national and international scene as an important producer of precious stones and the main gems are amethyst, citrine and agate. However, despite the immense potential of this mining activity, the extraction and processing of gemstones in Brazil present critical issues of infrastructure, which prevents a better development of these activities. In general, local production is still concentrated in small rudimentary mining. Recently some of these mines have begun to regularize their activities, in conjunction with the National Department of Mining Control. Besides these problems best practices for extraction activities and environmental control are not usually observed. Another problem which is placed in a critical way is the absence of aggregate value for the products of small mines. In this situation, the miners have great problems to obtain access to technology and adequate infrastructure. In most cases miners need negotiate their gems without processing, transferring most of the profit to intermediate traders. These results in heavy losses for the producer and for the communities involved. Given this scenario, the present study aimed at defining systems technically and operationally viable to be implemented in these communities in order to add value to gemstones. In this study best practices to thermochemical coloring systems, analysis of effect of raw materials and operating parameters on the final color of the gem were analyzed with attention.

Jan 1, 2014

By D. Moradkhani

The heap leaching of oxide copper ores with copper cathode recovery by solvent extraction and electrowinning is now well established as a low-cost method of copper recovery. The main purpose of this study was to extract copper from the copper low-grade oxide ore of Chodarchaei mine using column leaching. The copper oxide ore contained 1.1% Cu and 1.75% Fe. The mineralogical analysis indicated the malachite (Cu2(OH)2CO3) was mainly composed of oxidized phases. The sulfuric acid leaching experiments were performed under the laboratory conditions. The influence of several parameters on the course of the reaction such as particle size, acid concentration, flow rate, and time was examined. The optimum collective extraction of copper and iron was obtained at a particle size of +10-15 mm for a leaching duration of 3 days with sulfuric acid concentration of 100 gpl and using a flow rate of 2.5 cc/min. Under these conditions, the recovery of copper and iron were 98.54% and 41.99%, respectively. Keywords: column leaching, copper, iron, working diagram.

Sep 1, 2012

By T. Niedoba

The ash contents in coal particles were examined in the paper dependably on particle size and its density. So, the two-dimensional regressive function Z=Z(?, D) was the searched object, where Z is random variable describing ash contents, ? - density and D ? particle diameter. This dependence is determined basing on experimental data concerning the coal of type 31. For this coal, the method of ordinary kriging is applied to calculate the values of a random variable Z. This method requires the proper selection of so-called variogram function, which 4 forms are considered in this paper in purpose to select the best solution. The given results were then evaluated by the residual deviation value and so compared with empirical data.

Sep 1, 2012

By B. Rai

Processing of dolomitic phosphate ores remains one of the most challenging problems in phosphate ore beneficiation. The beneficiation plant at Jhamarkotra in Rajasthan, India for example is currently using a conventional double stage flotation process which involves first a fatty acids flotation to produce a combined dolomite-apatite concentrate (bulk concentrate) from associated silicate gangue. Dolomite is then separated from this bulk concentrate by flotation with fatty acids collectors and depressing apatite with phosphoric acid and sulphuric acid. This process requires addition of large dosages of reagents (H3PO4 and H2SO4) to depress apatite and to maintain highly acidic pH during flotation. Furthermore several cleaning and scavenging stages are needed to obtain the product of desired quality. We have developed and employed a molecular modelling based methodology of designing selective reagents for apatite-dolomite separation. We have been able to take into ac-count the differences in the distribution of calcium cations on these two surfaces in our design and hence develop novel phosphonic acid based depressants for apatite-dolomite separation with con-ventional fatty acids as flotation collectors. We have demonstrated the utility and power of molecular modelling based reagents design approach through this work on beneficiation of Jhamarkotra dolomitic phosphate ore using our novel phosphonic acids based depressants at pH?s close to natural pH. It was possible to reduce the MgO content of the ore from as high as 13.3 % to 1.5% in a single stage flotation. Our flotation separation results on Jhamarkotra ore with these new phosphonic acids based tailor-made depressants for apatite-dolomite flotation separation are discussed in this paper along with results of corresponding molecular modelling computations on the same system.

Jan 1, 2014

By G. Pahomova

"It developed an alternative to traditional flotation enrichment refractory of complex lead-zinc ores to obtain conditional lead and zinc products. The scheme involves the use of the processing method of gravitational enrichment of the primary cycle and the combined gravity-flotation-hydrometallurgical in finishing. The method has a high level of comprehensive utilization of mineral raw materials in relation to the elements that are extracted in the process of enrichment in lead concentrate, and the increase in recoverable value of processed ores. INTRODUCTION The primary source of lead are complex sulphide lead-zinc ore, lead ore actually rarer. The value of lead and zinc ores (except lead and zinc) is determined by the presence in them of a wide range of associated components: silver, contained mainly in galena; gold; bismuth in the form of its own minerals, but is associated with galena; cadmium contained mainly in the sphalerite; indium, thallium and gallium contained in sphalerite and galena; selenium and tellurium are present as impurities in the sulfide, tellurium is also found in the form of its own minerals. Of note harmful impurities antimony, which is often associated with lead sulphosalts and arsenic, having a substantially own minerals. By quality (content of lead, or the total content of lead and zinc) lead-zinc ores are divided into rich, ordinary and poor; by oxidation - to sulfide (with a lead oxides content less than 15% and zinc oxide content less than 10%), mixed and oxidized (50% oxide); the latter have a subordinate importance as a source of zinc and lead. Traditionally, the most contrasting technological properties of sulfide ores of nonferrous metals considered flotation properties, which determines the priority in the selection of flotation technology of their enrichment. Other methods of enrichment - gravity (jigging and enrichment in heavy suspensions), radiometric sorting (separation) are used as preliminary operations whose main purpose is to increase the content of lead and zinc in the ore sent to flotation, as well as the removing of part of empty rock in dumping tails prior to flotation. Effective implementation of these methods is possible at large size emphasizing in the ore of lead and zinc minerals, which is typical of the rich ores and which so far mainly worked. At the same time, non-ferrous metal ores (polymetallic, lead-zinc, copper-zinc, etc.) have a sufficiently high contrast to gravitational properties since ore minerals have a higher density compared with a rock minerals. But the gravity of the practice of non-ferrous ores enrichment is not widely used, despite its high degree of environmental safety and lower cost expensive."

Jan 1, 2018