Search Documents

By Robert Martin, Brian W. Stump

As part of a series of seismic experiments designed to improve the understanding of the impact of mining blasts on verifying a Comprehensive Test Ban Treaty, a sixteen station network of three-component seismic sensors were deployed around a large cast shot in the Black Thunder Mine. The seismic stations were placed, where possible, at a range of 2.5 kilometers with a constant inter-station spacing of 22.5 degrees. All of the data were recorded with the seismometers oriented such that the radial component pointed to the middle point of the approximately 2 kilometer long shot. High quality data were recorded at each station. Data were scaled to a range of 2.5 kilometers and the sum of the absolute value of the vertical, radial, and transverse channels computed. These observations were used to construct radiation patterns of the seismic energy propagating from the cast shot. It is obvious that cast shots do not radiate seismic energy isotropically. Most of the vertical motion occurs behind the highwall while radial and transverse components of motion are enhanced in directions parallel to the highwall.

Jan 1, 1997

By R Wing, D Corkery

"Several mines in the region of Sudbury, Ontario, occur in or near populated areas. In anattempt to examine the effects of environmental changes and blast induced vibrations onhomes in the area, a monitoring study was conceived. The study was conducted fromNovember 1990 to May 1991 in homes located near the 880 Stope at INCO Ltd.'s CopperCliff South Mine."

Jan 1, 1993

By Bryan Papillon, Karl Christopherson

In order to improve vibrations from quarry blasting, a new technique and timing pattern was established and applied to the particular geology. By shooting a single representative borehole one full second ahead of the production blast, a signature waveform can be isolated and analyzed. Multiple productionsignature blasts were performed. Encroaching residences require quarries to adjust their blasting techniques to reduce vibrations and raise frequencies. A signature hole inherently poses problems to quarries. Blasting one single hole from a production bench poses safety issues to wall stability; vibration issues to close neighbors; and budget issues to the quarry operator. Results showed that the new timing pattern reduced vibrations through timing optimization without a loss in quarry production. Therefore, this technique of vibration analysis employing a production-signature hole is successful in creating a timing pattern that meets the quarry’s goals.

Jan 1, 2008

By Tacio Ferreira

A surface copper mine in the Western United States faced challenges in recovering rock and ore from final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall conditions. The operation had been using the same drill and blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at approximately 380,000 tons a year generated from an average of 60 final wall blasts performed annually. The mine engineering team and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. In this paper we present how we collected data, reviewed design standards, and found opportunities to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71% on the mine’s highwalls.

Jan 21, 2025

By Dr. Zach Agioutantis, Elliott Morgan

The explosives, mining, and heavy civil industries consistently battle the uncertainty that is associated with working with a heterogenous medium like rock in blasting. This has led to studies to increase fundamental understanding of material response under dynamic loading that is associated with blasting. This study looks at the dynamic strain associated with blasting the lab Split-Hopkinson Pressure Bar (SHPB) testing while also building off of previous studies with the goal of better understanding the dynamic forces that are enacted on a geologic body during a blast loading event. This is required in order to advance geologic blast response modeling. This is achieved through analyzing the stress and strain values for each specimen that are calculated from strain data collected with a SHPB. Based on this data, the dynamic material response characteristics are able to be determined. Tests were conducted on five Berea Sandstone specimens with a rough length to diameter ratio (L/D) of 1.0. The strain data from these tests were then used to create stress strain curves as well as charts depicting failure stress to both strain rate and failure particle velocities. The tests conducted returned similar results to previous tests results on Berea Sandstone while also showing a correlation between strain rate at failure and failure particle velocities. While further research is needed, there is evidence that SHPB test data could be used in conjunction with the MBF model. The MBF model states that the peak particle velocity (PPV) of blast vibrations can be correlated with deformation (strain) at a given point. With a further understanding of dynamic material response correlated to PPV measurements, further refinement could allow for better prediction of blast performance.

Jan 21, 2025

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997

By Greg J. Stach, Norman "Skip" Hale

The authors describe the development of an overburden blast casting program in the upper seam of coal at a 2-seam surface mining operation on property adjacent to an active operating underground coal mine. Control of vibration is essential.

Jan 1, 1984

By Rene A. "Moose" Morin, Craig Copping

Innovative concepts in drilling and blast design have been used to remove deteriorated concrete and have enabled contractors to reduce costs and time on St. Lawrence Seaway rehabilitation projects. Time is of the essence on these contracts since the Seaway system is only available for this work during the winter freeze up. Unique electrical sequential initiation systems and specially modified drilling equipment have been used to accurately remove a narrow slice from the 83 foot high lock walls. These new methods successfully reduced demolition time, minimized overbreak and adhered to strict vibration limits.

Jan 1, 1986

By Richard G. Burdick

The use of explosive charges for generating seismic energy has been around for a long time. For oil-field work or crustal studies, when the target of interest is many thousands of feet deep, the surface waves and similar phenomena are of little consequence. In mining applications, however, when the target is a few tens or hundreds of feet deep, the return signals are often masked by these waves and an accurate interpretation is difficult or impossible.

Jan 1, 1981

By Paul N. Worsey

Disturbed zones of rock have been measured for blasted highway rock cuttings by Matheson and Swindells of the Transport and Road Research Laboratory (TRRL) of Great Britain. These zones have been shown to be directly attributable to the blasting process and accordingly vary in depth depending on blasting technique. Perimeter blasting such as smoothwalling and pre-splitting has been shown to be effective in reducing the depth of disturbed rock. Although extensive work has been carried out on surface excavations for medium diameter (l00mm) blast holes, none has been undertaken for underground excavations.

Jan 1, 1985

By Tom McDonald, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to soft material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessary as vertical presplit drilling produced wall failures.

Jan 1, 1997

By John M. Bolger, Keith E. McMaster

Excessive salt fines are undesirable in underground salt mining as they are considered a costly waste byproduct. This paper describes an extensive explosive application program conducted at The Canadian Salt Company Ltd, located in Pugwash, Nova Scotia, Canada. The prime objective of the program was to reduce the quantity of fines generated from this company’s underground production blasts. The program was known as the “The Fines Reduction Program”.

Jan 1, 1996

By L. Russell Payne

The use of shock tube in the blasting industry is relatively well characterized and understood within the realms to which it is used. Non-conventional uses of shock tube within the EOD and the Aerospace Industry however has not been as widely researched and published. Characteristics of shock tube such as its reliability, simplicity and its non-electric nature make it ideal for functioning or driving mechanical mechanisms, detonators, and timing devices. Outlined in the text are the performance characteristics of shock tube in an array of atmospheric environments including pressures ranging from ambient to 100,000 ft equivalent atmosphere. In addition the useful exit work energy or impulse of the shock tube for driving these various EOD and Aerospace mechanisms is published as a function of tube lengths and atmospheric pressures. Of particular interest to these devices is the required length of shock tube needed to produce the steady state detonation energies and the accompanying properties of the shock tube at these lengths. Various sources publish an arbitrary run distance for steady state detonation and output some where between 20 cm and 1.0 meter. Statistical and experimental evidence with in the text show these numbers to be low and provides an updated reference for shock tubes usage in nonconventional situations.

Jan 1, 2008

By Peter Moser, Andreas Grasedieck

In modern rock blasting it is becoming more and more important to achieve a certain specified fragmentation. This means that the rock particles formed as a result of the blast should conform to a desired particle size distribution. An important issue with respect to achieve a desired blast result in terms of fragmentation is both the availability of models for the prediction of the characteristic of the particle size distribution of blasted material and the determination of the energy necessary to achieve a certain fragmentation status. Within the research project “Less Fines” funded by the European Union under project reference G1RDCT200000438, the latter has been addressed by the Department of Mining Engineering& Mineral Economics of the University of Leoben. For that purpose fragmentation results from lab scale blast tests have been analyzed and the relationship between the specific charge used for the blasts and the resulting specific surface of the fragmented material has been examined. Linear relationships between the specific charge and the specific surface of the resulting fragmentation were found for various types of rocks to apply over a range of 10 for the powder factor.

Jan 1, 2004

By T. Bajpayee, G. Mowrey, D. Ingram, T. Rehak

Blasting operations are an essential element in the recovery of our Nation’s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining .operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining.

Jan 1, 2001

By Lyall Workman, P D. Katsabanis

Energy released by the explosive is typically partitioned in brisance, heave and losses. The fact that energy released in the P-V expansion curve below a certain point is lost has resulted in the concept of available energy. Through simple calculations it is shown that energy released at pressure levels thought to be low, amounts to a significant proportion of the total energy value. Furthermore, throw calculations indicate that the assumed loss of that part of energy does not justify practical results. Loss of energy at the low pressure levels may also not be justified from the fragmentation point of view as pressure levels below 1 kbar are enough to extend radial fractures around a borehole. Finally the equation used for the P-V behaviour of the explosive gases is important in throw calculations. Simplified approaches may not reproduce the performance of the explosive which is not characterized only by its energy content.

Jan 1, 1998

By C Jamie Kridler

"An increased concern for pit safety and more stringent, highwall requirements for augermining of final cuts has led to a new emphasis on wall control for a Central Pennsylvaniacoal operator. Over the course of two and one half years and several locations, fieldpersonnel developed a very practical yet very effective system for maintaining safehighwalls. This involved the use of the blast design to: l) shape the highwalls 2) create andprotect a system of benching 3) pre_split large diameter holes using suspended ANFOcharges."

Jan 1, 1993

By Edward J. Walter

A vibration record is a complex of motions resulting from a combination of direct, reflected and refracted seismic energy that originated at a blast source. Multiple hole blasting using delays further complicates the motion in that overlapping of seismic wave trains may occur when delays do not fire in the programed sequence. This can result in variations in amplitude, frequency and wave-1ength of the vibration. Amplitude may be doubled, frequency may oscillate between the highest and lowest frequencies present and wave-length may approach doubling of the longest wave-length present. These effects can present serious problems to conducting a safe blasting program since increased amplitudes and lower frequencies present higher damage potentials for structures. The development of these effects is described and illustrated graphically to show how these effects can occur.

Jan 1, 1989

Several surface coal mining operations in North America are attempting to adapt microprocessor-based monitoring equipment as well as programmable logic controllers onto rotary blasthole drills, towards improving overall drill and blast productivity. These Monitoring While Drilling (MUD) systems permit the recording and processing of important drilling parameters such as rotary speed and torque, instantaneous penetration rate and weight on the bit, and enable the operator ultimately to optimize drill and bit performance. MWD systems on production drills in surface coal mines offer the potential to define mine bench geology in detail and in advance of explosives loading. Recent advance s in explosives and initiation technology will require such a detailed knowledge of ground conditions in order to be fully exploited. Additionally, the logic developed from drill monitoring technology will eventually enable full drill automation through feedback and control, once a more complete understanding of the influences of rock mass characteristics on machine performance is achieved.

Jan 1, 1988

By Henry P. Van Ormer

This paper is written to outline the capabilities and flexibility of the electric motor driven oil cooled rotary screw air compressor in construction and mining applications. With the changing economics between fuel and electric power all over the world, the viability of the electric motor is a choice all construction and mining people should be aware of. The advent of large efficient electric motor driven rotary screw compressors have given a great deal of flexibility to the use of these units on many applications not considered before. Examples are given for rotary and percussion drilling, fennels, and underground, sandblasting and "uniting, general uses - shows wheel mounted and skid mounted units.

Jan 1, 1976