Search Documents

By Norman S. Smith, Troy D. Harris, Richard L. Ash

In open-cut bench blasting drilling boreholes below grade level is normally considered essential to insure toes do not remain. The extra drilling and use of explosive below floor level are not only expensive but on occasion cause serious problems including severe floor damage and excessive ground vibrations. It has been reported that under certain circumstances explosive in the subdrilling has been successfully substituted by broken rock with its associated benefits.

Jan 1, 1978

By Rahim G. Haghighi, Calvin J. Konya

Fragmentation is the fundamental concern of rock blasting, serving as a measure of blasting effectiveness. Fragmentation is sensitive to the inter-relationship among the design variables which define pattern geometry. Therefore, the objective of this study was to develop a model which represented a confined bench blast and to investigate the movement of burden-rock as the length to burden (L/B) ratio was varied.

Jan 1, 1985

By Eduardo Gonzalez Fernandez, Jaime Rios Vazquez

This report substantiates the connection that always exists between explosives and vibrations and draws attention to low frequency vibrations, which are the moat dangerous for the structures affected.

Jan 1, 1986

By Jim Breedlove, Stephen P. Case

When a major ground subsidence occurred in the AKZO Salt mine at Retsof New York, the company was forced to pick up their production from a lower mine level. Before full production on the lower level was possible, an escapeway and ventilation shaft would have to be constructed. Construction of a shaft under emergency conditions required some special techniques. Dynatec Mine Construction, Inc. of Lakewood Colorado was awarded a contract for the project.

Jan 1, 1995

By T Weaver, R Dick, R Sivakumar, C T. Aimone

A series of small-scale crater tests were performed in concrete and sand in an effort to understand the cratering process in large-scale field blasts. The surface orientation of these tests varied from flat to a 30° slope. In comparison to previous crater experiments in competent oil shale, the crater tests in concrete produced craters similar to those in oil shale after scaling the measurements for differences in the mass of explosives among the experiments. Material strengths and the degree of brittleness had a significant effect on the size and shape of the crater. The small-scale sand tests resulted in some crater features that were similar to large explosive tests in alluvium and soil.

Jan 1, 1986

By Francis O. Otuonye

A time series and system analysis modeling technique was applied to signals from strain egages mounted on a fully grouted resin roof bolt and signals from accelerometers mounted on the bolt head and roof rock to determine the roof bolt's response to repeated blast loading. The derived model gives a comprehensive quantitative description of the modes of vibration of the roof bolt response to each blast loading. The damping ratios and natural frequencies of the modes of vibration can reveal the alteration of the process dynamics due to the deterioration of the roof rock and can be used to identify the incipience of instability in the roof bolt system.

Jan 1, 1987

By Joseph Meyers

Explosives techniques and technology are constantly evolving and improving, yet basic communication and business skills are not being used regularly. Many potential blasting projects never occur due to simplistic, basic factors, such as a lack of communication. Articulate communication is the key component in the blast approval process, which has changed remarkably from how business was conducted fifty years ago. Imperative to the approval process is communication outlining the safety and benefits of the blasting project. Information and transparency with the stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the chances of having a blasting project approved. This open communication starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. The blasting industry and regulators must work collaboratively to improve safety, security, regulations and licensing. Implementing state of the art blasting techniques, security, safety measures, vibration monitoring and strict licensing allows the AHJ and all stakeholders to remain integrated and informed, contributing to process approval. Regulatory operators should strive to achieve success thru communication, cooperation and compliance which is accomplished thru continued education and transparency. These steps, combined with regular meetings, has proven to be a benefit to both industry and regulators. Relationships are built through trust, teamwork, transparency and communication –including the take holders and AHJ in the approval process from the inception solidifies these relationships and improves teamwork

By John Wright

During June and July 1999 a United States Antarctic Program (USAP) team of three commercial divers and one blaster successMy removed an underwater rock obstruction which interfered with safe docking practices of research vessels that call at Palmer Station - the USAP research facility located on Anvers Island, Palmer Peninsula Area, Antarctica. Ordinarily, such a project might be considered routine. However, certain aspects of the project, particularly those dealing with logistics in a remote corner of the earth, sat3eguards for marine biota, and working underwater in the dark of the austral winter, conspired to make this project interesting. Even more challenging was ensuring the protection of the existing pier - a deeply corroded sheet pile structure backfilled with loose gravel and rock - which lay less than 50 feet away from the target obstruction, not to mention uncertainties at the outset as to the nature of the rock mass forming that obstruction.

Jan 1, 2001

By Roger N. Prescott

The Bureau of Alcohol, Tobacco and Firearms (BATF) is sponsoring legislation requiring the addition of identification taggants to commercial explosives. These are plastic particles with color coded layers that theoretically can be used to identify the explosive by date shift code.

Jan 1, 1980

By Chapman Young, William L. Fourney, Richard D. Dick

During 1981 and 1982, an extensive oil shale fragmentation research program was conducted at the Anvil Points Mine near Rifle, Colorado. The primary goals were to investigate factors involved for adequate fragmentation of oil shale and to evaluate the feasibility of using the modified in situ retort (MIS) method for recovery of oil from oil shale.

Jan 1, 1985

By Jeffrey N. Deisher, H Y. Fang, Richard P. Scheller, Robert M. Koerner

The need to adequately quantify cracking in structures in the vicinity of blasting activity becomes more important each year. This urgency comes about through a growing number of complaints and lawsuits between the various parties involved, i.e., operator/owner, government, and complaintant. It is felt that existing rules and regulations (mainly based on peak particle velocity of the soil or rock adjacent to the structure in question) fall short of such quantification and lead to confusion in adequately assessing structural damage.

Jan 1, 1977

By Stanley J. Vitton

An important factor to consider during blast damage investigations is whether the structure was constructed on collapsible soils. Traditionally, these soils have been considered to be soils such as loess deposits, which occur along the Mississippi River in locations such as Vicksburg, MS. However, recent research into collapsible soils has indicated that a number of soils may also fall into this category. A collapsible soil is any soil that is susceptible to large decreases in bulk volume upon saturation.

Jan 1, 1997

By K Uenishi, H P. Rossmanith, N Kouzniak, A Daehnke

This contribution presents an introduction into that part of the field of elastic wave propagation which is relevant to blasting of boreholes and addresses briefly borehole breakdown and the formation of the fracture network around a borehole which ultimately leads to the disintegration of the rock mass. Phenomena of this kind are encountered in mining and quarrying. Numerical as well as experimental work referring to stress wave expansion from a detonating borehole is addressed.

Jan 1, 1998

Jan 1, 2002

By Alain Blanchier

Because in Europe and in many other countries as well every new project (quarry, mine, public work) needs a risk estimation to prove its feasibility, a model to estimate flyrock risks became necessary. This paper presents the basic hypothesis which should underlay such a model to estimate statistical flyrocks range for not only some single blasts but a whole project and in particular the way to take into account rockmass or blast pattern parameters variability. It describes a first usable quantitative flyrock model based on the characteristics of the blasting plan and of the generic laws utilised in casting and selective blasting operations and on a statistical approach of rockmass. In a second step, this paper discuss an approach of risks estimation compared to the classical one used in pyrotechnics studies for explosive magazine risks assessment.

Jan 1, 2013

By Hans Perlid

In the handling of emulsion explosives pumping is a key operation. A number of serious accidents has shown that pumping can be a risky operation and should be care&lIy considered and investigated. This is the background behind a series of pump tests carried out by NTTRO NOBEL.

Jan 1, 1996

By David Sprott

The effect that underground blasting has on the stability of hangingwalls, pillars and other rock structures is an inherent part of Noranda's geomechanics and mine design program to improve mine safety and stability, increase productivity and reduce ore dilution. The blast monitoring program at Noranda Research aims to provide values of particle velocities and accelerations, delay firing times, and vibration periods to assist with practical blast design and controlled blasting techniques.

Jan 1, 1988

By Douglas Lindsey, Glenn Hazen, Shad Sargand

"With the innovation of computational equipment, an exact analysis of structures as dynamic systems is more approachable. Accordingly, the dynamic system can be established, if the natural characteristics such as the natural frequency and the damping fraction of a system are known. Through dynamic analysis, the response of a structure can be predicted from ground vibration, and it becomes possible to forecast the damage potential to the structure with reasonable accuracy. Most vibration will appear as single harmonic or superposition of waves that consists of several harmonics with different frequencies. A vibration signal can be expressed, therefore, as the function of sine waves. If a signal is periodic, the particular harmonic with the smallest frequency will befundamental and frequency of the others will be multiples of the fundamental frequency."

Jan 1, 1993

By Dale Preece, Stephen Chung

Development of DMCBLAST-3D is continuing and now includes the capability to simulate the detonation of multiple blastholes in multiple rows that make up a conventional bench blast, either in a rock quarry or a surface coal mine. DMCBLAST-3D is a three-dimensional extension of the proven twodimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2002

By Gregory Lorsbach, Wade Hutchison, Earnest Grigoryan

Comparing measurements from multiple seismographs, particularly when the instruments are deployed in a “side-by-side” situation, is often problematic. Measurements often differ by as much as a factor of two. These differences are attributed to issues related to calibration, geophone coupling, and differences in geology over very short distances. Unfortunately, these explanations are often purely qualitative, but are accepted as factual. Shake table testing often demonstrates that those seismographs that indicate large differences for a particular vibration event, may correlate within a few percent of each other and the known shake table input. Geophone coupling also does not fully explain the difference in measurements since geophones in side-by-side measurements are deployed identically. Differences in geology do not explain the difference in measurements since it would be unrealistic to expect significant differences in distances less than one meter in a normal monitoring situation. Utilizing a new technological approach to vibration measurement and analyzing numerous side-by-side measurements, it has become clear that a significant portion of the observed differences between seismograph measurements are instrumentation induced. This study examines and describes some of the most significant sources of the seismograph error budget.

Jan 1, 2005