Search Documents

By Gregory B. Poole

Data collected with 16K sampling at a variety of blasting sites (construction, quarry, trench, mine) and monitoring locations was analyzed to effectively show the 16 different 1K readings all based on the microsecond that the unit went into monitoring.

Feb 1, 2020

By Michelle Crull, Susan Hamilton

Explosives safety requirements in the United States began in 1909 when the American Railroad Institute questioned explosives manufacturers regarding distances necessary to protect employees and property. In response to this inquiry, a group of explosives manufacturers collaborated to study over 200 explosive accidents. This study resulted in the 1914 American Table of Distance (ATD) published by the Institute of Makers of Explosives (IME). The 1914 ATD provided suggested separations between explosives and inhabited buildings, public highways, and public railways.

Jan 1, 2010

By C. Aimone-Martin, C. Dowding, M. Jern, J. Gjødvad

This article compares percentages of compliance for six national standards to demonstrate how these standards vary on-site in a real project. This, to the best of the authors' knowledge, has not been accomplished before. Different standards not only vary in allowable amplitudes of induced vibrations but also in how they are measured (transducer location, transducer orientation, frequency content of vibration, etc.). Thus it is not straightforward to compare the permissible values of induced vibrations with each other. This challenge of comparison is overcome in this project by instrumenting a structure with multiple transducers according to different national standards and comparing the degrees of compliance. Compared herein are compliance with standards used in United States of America, Germany, Great Britain, France, Austria, and Sweden. Averages of the percentage of compliance and ratios of measured vibration amplitudes for all six national standards are compared both in tabular and graphical form for 20 blasts at the Aitik mine northern Sweden. It is the largest open pit mine in Europe and blasts are atypically large with more than 1000 kg charge per hole and several hundred holes per blast, lasting 3-5 seconds. Results show that percentages of compliance can vary by as much as 2 to 75 % for these blasts at this structure. The overall project is a cooperative effort between EFEE (European Federation of Explosives Engineers) and ISEE (International Society of Explosives Engineers), supported by more than 17 persons from 8 different countries. At the present the experts are the four authors of the present paper and Dr. Robert Farenfield, Dr. Nathan Rouse, Douglas Rudenko, Brent Meins, Kenneth K. Eltschlager, Karin NorénCosgriff, Travis A. Davidsavor, Vitor Luconi Rosenhaim, Johannes Kutschera, Bernard Thierry, Thomas Moser, Cory Loukedis, and Keith Best. The project began with a literature study and a survey including an evaluation of the answers provided by members of EFEE. Results were presented at the ISEE conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019 (Gjødvad & Jern, 2019; 2020). The second part of the project was initiated in May 2021 with installation of 7 seismographs from two different manufactures, 3 cracs gauges and 2 microphones on a building at the Aitik mine in northern Sweden. The third part of the project has moved to the United States. Two residential structures adjacent to quarries are being monitored in Michigan and Ohio. Installation and monitoring began in March 2023 and are expected to continue for 6 to 12 months. In addition to the objectives of phase two the 2023 study includes calculations of global wall strains from measured velocity time histories and measurement of response of existing cracks to vibratory and climatological effects

Jan 1, 2024

By Lon Santis, Bill Evans, John Tatom

Debris data from the Department of Defense Explosives Safety Board’s Project ESKIMORE full-scale explosives event test program are compared to quantity-distance (Q/D) standards and quantitative risk analysis (QRA) methods. The ESKIMORE test program involved quantities of explosives ranging from 1,000 to 60,000 pounds detonated in typically sized structures made of metal and concrete. Debris from these events was extensively surveyed and catalogued. The debris patterns from these events show varying degrees of directionality normal to the walls of the structures. These density patterns are overlaid an existing explosives storage site that is comparable to the test conditions. Analysis of the debris patterns in relation to Q/D standards shows that exposures located beyond the Q/D arc but along the normal to walls of potential explosion sites (PES) may have much higher debris density than exposures at the same distance on the corners of the same PES. Analysis of the debris patterns shows that predicted patterns using the QRA tool IMESAFR v2.0 closely match actual patterns. Additionally, IMESAFR based QRA methods are able to quantify the different risk levels of being exposed along the wall’s normal as compared to being exposed on the structure’s corner. Methods and decision making criteria to mitigate risk based on the directionality of PES debris are presented. Copyright ©

Jan 1, 2015

By Nikolaos Petropoulos, Ulf Nyberg, Daniel Johansson

A series of signature boreholes were blasted to observe any difference between confined and free face blasts. Four geophones were used to capture the compressive wave. The conventional approach, i.e. the calculation of vectorized peak particle velocity (vPPV) did not show any difference. Also a wavelet transform was tested.

Feb 1, 2020

By Joshua Hoffman, Philip Mulligan, Braden Lusk, Tristan Worsey

Blasters rely upon detonators to achieve the designed timing sequence to move material where it needs to go, minimize vibration, or optimize fragmentation. At times detonator inventory on seldom used delays may be slow moving. This can lead to detonators being used long after they were manufactured. This paper addresses the potential shelf life concern as it relates to timing accuracy of shock tube detonators. A recent study was conducted to study the timing accuracy of non electric shock tube detonator systems. A follow up study was then conducted to determine the degradation of the non electric shock tube systems accuracy with time. The follow up study is presented in this paper. Samples of detonators from the initial study were set aside for approximately one year and then tested. The results from the aged detonators were compared to those of the detonators that were tested in the original study. As an extreme case a third set of shock tube detonators was tested using detonators that were between eight and nine years old. The results from these tests are presented as well. Each system was tested at a short medium and long delay time. Statistical analysis was conducted to determine the effect of time on the detonators accuracy. This paper quantifies the importance of regular inventory cycling to help preserve manufactured timing when using non electric shock tube detonator systems.

Jan 1, 2013

By Adrian J. Moore, Alan B. Richards

Responsible blasting requires that rock throw be controlled to ensure that no danger will result to people and property. This paper describes the development and testing of empirical field calibrated formulae that can be used to evaluate rock throw, provide an early warning of when reduced burden will endanger people and property, and prevent flyrock incidents. Inputs to the formulae are charge mass, burden or stemming height, and a site constant that lies within a general range that can be tightened by site calibration. The output is the distance that rock will be thrown, and this ‘design your own flyrock’ quantification can be used to establish both safe clearance distances, and the critical range of burdens and stemming heights where the situation changes rapidly from safe to hazardous. Examples are given of the use of the model to control flyrock in open-pit mining and quarry operations, in situations which are controlled by both burden and stemming height.

Jan 1, 2004

By Frank Barker

Mining operations present a very different environment to the suppliers of explosives, initiating systems and services, both on surface and underground. Typical hazards include underground movement, air quality, ground stability, moving equipment, and the use of explosives. As contractors to the mining industry we do not have management control over the environment in which our people operate. The hazards and consequent level of risk that our people are exposed to in some mining operations are significantly higher by orders of magnitude than in a normal factory environment. Orica Explosives (and other Explosives suppliers) are continually and increasingly identifying opportunities to partner with customers by adding value through the provision of services leading to a reduction in total mining costs. These services include the provision of a bulk underground loading services, delivery of product into underground magazines, magazine management, value added blasting, conversions, rock-on-ground contracts, and blast management programs.

Jan 1, 2000

By Rob Lederer, Chris Batten

Traditionally coal model digital terrain models (DTM) are created from lithological information obtained from broad scale exploration holes. The grid layout and distance between holes means that models do not commonly display local variations of seam dip, faulting and shearing. Due to this, issues can often arise when designing the loading of blast patterns based on potential variances between model and actual coal seam locations. Many sites will often attempt to create more accurate models through the collection of data from coal edge pickups on highwalls and in blast faces, along with information recorded by drillers (touch coal holes) from both production and presplit holes for both the current and previous blasts.

Jan 1, 2012

By E. Líder, J. Pavez, J. Rivera

The application of new technologies, methodologies, and the use of new products in mining operations is a practice that is becoming more common in the industry every day, added to the new challenges and restrictions found in the operation. In the city of Tierra Amarilla, the interaction between mining operations and the community presents a constant challenge given the proximity to the community and the limitations that this presents. Explosive charge mass, in conventional blasting using traditional explosives (ANFOs, packaged explosives for example) limits the explosive charge lengths (they are reduced), impacting the explosive charge productivity. To improve the productivity of explosive charge and fragmentation, the use of low-density explosives was proposed, allowing the increase of the explosive charge length, trying to maintain the vibration levels within the established limits (2mm/s), preserving the fragmentation of the rock in the required sizes. The present study shows the results obtained from the application of low-density bulk emulsion for production blasting charges using upward and downward fan drillings. During this process, 18 blasting events were carried out, of which 8 were Up-hole loading (average density of 0.75 gr/cc) and 10 with Down-Hole loading (average density of 0.95 gr/cc). In summary, a total of 110,760 tons of ore have been broken, using low density emulsion, meeting the proposed objectives such as: 33% reduction of vibrations, 12% overbreak (within the theoretical design), P80 of 11in and 4.6% in fines.

Jan 1, 2024

By Theirry Bernard

The era of non-electric systems as an initiating system has revolutionised the blasting world by introducing a very safe initiating system that is reliable, with initiation sequence possibilities that are superior to those of purely pyrotechnical or electric systems. Electronic initiation has brought with it accuracy, programming and controls that were lacking in the non-electric systems. However, it has also led to a certain degree of complexity, which works against user-friendliness, sometimes introducing a few constraints that are balancing out the intrinsic performance of electronic detonators. The introduction of a hybrid initiation system, Electronic and Non Electric, offers accuracy, and flexibility that were lacking in non-electric systems, whilst removing the inherent complexity of electronic systems. This paper endeavours to summarise the advantages and disadvantages of non-electric and electronic initiation systems that have been recorded after years of experience on site. The paper will then describe how a hybrid system only keeps the advantages whilst eradicating the disadvantages, via a case study.

Jan 1, 2007

By Visitor Makiyi, Chris Batten

Poor coal recovery due to coal damage or loss caused by blasting can have a significant impact on a mining operation. Increasing coal recovery by reducing blast damage can provide a significant opportunity for coal mines to maximise their revenue and reduce their operating costs. This paper provides details on advanced drilling and blasting techniques used throughout the coal industry globally to prevent coal damage and movement during blasting. Typical coal loss and damage mechanisms are explained, along with how each of the applied techniques works to minimise the impact of each mechanism. Key requirements for a coal loss reduction program are detailed with typical design parameters used for each of the methods discussed. The positives and negatives of each method are also provided to enable comparisons and help determine suitability for a particular coal mining operation.

Jan 21, 2025

By Milos J. Bila

I would like to discuss today several safety topics that we at Nobel feel are going to be particularly critical to all of us who are involved in the manufacturing, transportation, storage and use of commercial explosives during the '90s. My purpose is to identify these topics in order to allow those in the commercial explosives community to better understand the potential difficulties we face.

Jan 1, 1992

By Harry Verakis, Thomas Lobb

Blasting accident data over a 30-year period (1980-2010) are summarized and presented for all types of surface and underground mining operations in the USA. The historical record of injuries from blasting accidents in all types of mines continues to show a significant decline. The overall decline in mine blasting injuries in the U.S.A. has resulted from advancements in blasting technology, training and improvements in blasting products and blasting processes. Some of the technology advancements such as safer blasting agents and computerized bulk vehicle loading, electronic detonators and remote operated blasting systems, and computerized blast design have and continue to significantly contribute to improvements in the historical blasting safety record. Also, the progress of significantly improving the safety of mine blasting has resulted from the combined efforts of miners, mine companies and operators, miners, unions, explosive and blasting product manufacturers, associations such as the International Society of Explosives Engineers and the Institute of Makers of Explosives and various government agencies.

Jan 1, 2012

By Deepesh Yadav, B. S. Choudhary

Underwater drilling and blasting is conducted for deepening of sea channels for port berths, lake or reservoirs for water supply etc. so that rock dredging becomes easier. During this process there are several associated unwanted effects having potential to cause damage to surrounding structures and the environment, flora and fauna. Though all these ill effects can’t be completely eliminated but adopting controlled blasting techniques can minimize these to tolerable levels. It is recognized that ground vibrations resulting from rock blasting below water near dam may endanger the safety of earthen dams. Therefore, controlled blasting technique was used to ensure the safety of dam and its efficacy was established by monitoring of blast vibrations. The usage of small quantity of explosives confined in blast holes, non-electrical delay detonators and initiating each hole with a separate delay helped to minimize the ground vibration effects on surrounding structures.

Jan 1, 2018

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Pierre Auger, Benoit Levesque, Richard Martel, Guy Sanfacon, Louis-Charles Boutin, Marc-Andre Lavigne, Patrick Brousseau, Luc Trepanier, Louise Galarneau

Explosives used for blasting operations in civil engineering works, like construction of piping systems under roads, of pools, of houses and buildings can generate large volumes of carbon monoxide (CO). Carbon monoxide can represent between 1 to 3% of the gases produced by usual explosives. The production of 10 to 24 1 of CO by kg of explosives blasted is theoretically anticipated. CO is a gas that has no characteristic colour, smell or taste. It can migrate in the fractured rock of the blasted areas on fair distances, and then infiltrate in closed spaces like sewage systems, manholes, but also in basements of houses. In Quebec, in the last 10 years, 7 people were poisoned by CO in their houses to the point that they had to be treated in hyperbaric chambers. In the USA, many accidents have occurred and one worker died in a manhole. From the review of intoxication cases, the distance of migration of CO may reach 55 m if a conduit is present underground. Underground conduits broken by blast, tilling around underground conduits in road or house trenches, or fractured rock created by blasts between houses or between a house and a road, are the different pathways identified in the Quebec incidents. Field tests were performed at sites close to CO intoxication locations in order to evaluate the behaviour of CO in fractured rock following blasting operations. From these tests, the following conclusions may be drawn. The structural geology of the rock formation (schistosity, family of joints, fractures) plays a role in the direction and extent of gas migration in fractures generated when rock is blasted with explosives. The confinement of the rock can affect the quantity of gas migrating in the fractured rock. Significant concentrations of CO may persist in the fractured rock even 7 days after a blast. Advection is the initial mechanism of CO migration in fractured rock generated by the blasts or naturally occurring before the blast. The distance of migration with this mechanism is short (5 to 8 m). In trenches of muck (equivalent to tills under roads) the distance of CO migration by advection is 12 to 20 m. In the 2 to 3 days following the blasts, further CO migration up to 15 m is made by diffusion in the induced fractures, or up to 30 m in the trenches. To minimise CO production and migration in the fractured rock during blasting, special procedures can be applied by the blasting contractors: (1) do the complete excavation of the overburden before drilling and put mats for each blast; (2) do the complete excavation of the muck after each blast; (3) the last blasting should be the one for the private services entrance of the house and the excavation of the muck should begin at the junction between the road trench and the services entrance trench. Another technique consists in the pumping of interstitial air in the muck with a vacuum truck immediately after each blast.

Jan 1, 2002

By Gloria Contreras

The study aims to optimize the density of holes per tunnel section. The energy distribution, the one with the highest density, is used in the center of the diagram and is distributed homogeneously towards the contours with the lowest energies up to the contours to produce a perimeter control.

Feb 1, 2020

By Greg Quinn

After a long week of work in Colorado Springs this past July, I was looking forward to flying home to start a long anticipated family vacation. As I grabbed my seat on the plane, a man sitting next to me innocently inquired, to the row as a whole and not to me in particular, “I wonder what the weather will be like in Phoenix”? To most people, this is a common (maybe the most common) topic of casual conversation. To a meteorologist that just dealt with six thunderstorm delays at a major golf event over 4 days, well, lets just say the smirk on my face said it all. After giving my flight mate a detailed forecast and a short explanation on why I would know such information, I sensed, correctly, the inevitable follow up question was coming. “Why would you need a meteorologist at a golf tournament?”

Jan 1, 2012

By A. Ravi Kumar

A trench is a structure to accommodate fluid carrying pipelines for water, gas, petroleum products etc. Trench serves the purpose to haul the fluids in bulk over long distances safely and economically. Use of pipeline for moving oil and gas was essentially a post World War II development, but now it has acquired its own importance.

Jan 1, 2008