Search Documents

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By P. Couceiro, J. Navarro

A new methodology to perform selective blast designs by adapting the explosive energy, hole by hole (or in the hole), to the rock properties as a combination of their strength properties through the X-Rock model has been developed based on drill-monitoring data from both autonomous and manual rotary drilling modes. For that, a thorough normalization process has been developed to minimize external influences in the data induced by the different rig system and the operator interventions during manual drilling operation. Principal component analysis has been used to combine drill monitoring information. Data from 48,385 blastholes, comprised in 102 production blasts at 7 different levels in one expansion of the mine have been used for the analysis. The methodology, called X-Energy, combines the X-Rock model outputs with actual blast design parameters (drill pattern, stemming and borehole length, explosive mass/density and others) and a constant variable obtained from a machine learning algorithm, to estimate size distribution and percentage of fines and coarse material, hole by hole, by combining and recalibrating the Kuznetsov (Cunningham, 1987) based equation. From it, a new shovel-independent diggability model has been developed as combination of the P80 size, the rock properties (from the X-Rock) and a constant variable obtained from a machine learning algorithm. The X-Energy application presented in this study have been implemented in Minera Escondida Limitada (MEL), to design and operate production blasts with the goal of varying the explosive density to the rock properties to obtain a more uniform size distribution and digging rates, hole by hole, based on a target size and rate, and improving slope care, preventing active faults to fail. The methodology has been applied and validated in 17 production blast (8,277 blasthole), unlocking an average of 12.8% reduction in explosives costs (explosive consumption), by combining a pattern expansion strategy and a better distribution of the explosive density within the blast. The results demonstrate how a better distribution of the explosive energy by varying its density in the hole according to the rock and blast geometry variables can reduce powder factor (explosive consumption) while improving or maintaining blasting and digging results.

Jan 1, 2024

By Wiliam Reisz

As we approach the peak season for thunderstorm activity it’s important to keep in mind that lightning still poses a serious threat to drilling and blasting operations. Lightning remains the number one cause of accidental detonation of explosives.

Jan 1, 2008

By S. J. Dillingham

One of the primary goals of every blaster is to achieve the optimum blast design. Too much focus on efficient design, however, can cloud certain issues and exposures that must be addressed if the entire project is to be considered .successful.. Due to the known human response to blast effects and inherent dangers present in the use of explosives, the potential for the project being delayed or shutdown, or the blaster and associated company being named as a defendant in a lawsuit, is always a possibility. Therefore, the blast design and associated project bid must incorporate sound safety contingences and procedures that address those .what-if. Scenarios that may arise as a result of vibration, flyrock, public relations, and job-site personal safety.

Jan 1, 2002

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Serdar Celik, Yucel Karakus

This paper presents bench blasting designs based on results of vibrations analysis on test shots organized in an open pit coal mine located near to Soma district at Manisa province in Turkey. There are some structures which can be adversely affected by blasting at the coal mine. The one of the main goals of this study is to perform a preliminary assessment of possible damage effect of ground vibrations induced by blasting at these structures by risk analysis based on ground vibration measurements. During this investigation, the data pairs of scaled distance and particle velocity obtained from the 36 event records belong to 9 test shots were statistically analyzed and a PPV prediction equation specific to this site with 95% prediction line were obtained. And also, this equation was used in the derivation of the practical blasting charts specific to this site as a practical way of predicting the peak particle velocity and maximum charge per delay for future blasting. A risk analysis was performed by using this equation. In the light of this analysis, preliminary blast design model was proposed to be used in this coal mine for overburden excavation.

Jan 1, 2012

By Joe Dannenberg

One must be cautious in talking about blasting safety, because the very act of making a blast involves the creation of an infernal machine. You are setting up for the instant release of tremendous energy. Inherently this is a hazardous act. It has always been hazardous. It will stay hazardous.

Jan 1, 1975

By Scott Scovira

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one NA Quarry and Construction Business experienced a series of flyrock incidents. In the Spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Bjoern R. Petterson, Lars Haakon Siem

The world's longest highway-tunnel -- the Aurland Tunnel in western Norway -- is scheduled to be opened in the year 2000. A project to build a main highway between Oslo and Bergen with no ferry connections was approved by the Norwegian Parliament in January 1995. Construction of the five-year blasting project was started by the Norwegian Highway Authority in mid-March 1995, with an expected completion date of November-December 1999.

Jan 1, 1996

By Robert Lee, Pertti Paavola

Automated vibration monitoring and web-based data distribution has proven itself on the largest single construction project ever undertaken in Finland. The excavation for the Kamppi Center Project in the center of Helsinki was completed in November of 2003 and involved the removal of over 200,000 m3 (260,000 yd3) of rock and over 1,700 individual blasts. A system was installed, incorporating 37 discrete monitoring points located throughout an underlying metro station, and other surrounding underground and surface facilities. After every blast, vibration data was automatically transferred from the monitoring network to a server database. Stakeholders were able to access and review vibration reports on a password-protected website within 90 seconds of each blast. This allowed engineers to verify that recorded levels were in compliance with established limits, before proceeding with subsequent blasts. The data was also imported into a semi-automated Scaled Distance tool for analysis using linear regression techniques. This was used to determine, and adjust for trends in blast-induced vibration.Copyright

Jan 1, 2004

By M V. Van Bers, A L. McAnuff, A Curic

During the Summer of 1997, rock excavation was carried out for construction of the Centre Block Underground Services building (CBUS) abutting the most historically significant structural complex in Canada, the Parliament Buildings in Ottawa. Controlled blasting was required for the removal of 25,000 cubic metres of limestone bedrock within the ten week time window of Parliamentary recess. A test blast program carried out in 1996 had established that close blasting was viable even within the very restrictive limits considered necessary to preserve the structural and cosmetic integrity of these historic structures. In total 300 blasting operations were required to complete the excavation, including the 20 test blasts conducted in 1996. Based on attenuation characteristics established for the site during the trial blast phase, the blasting contractor proposed excavating the CBUS site in three zones. Each zone contained differing drill patterns, depths and explosive loads. Vibration intensities, air concussion levels and displacements across representative existing cracks were measured and recorded at numerous observation points within and around the Centre Block and the Library of Parliament, as well as on the grounds of the Parliamentary Precinct. The blasting portion of the excavation was completed within budget in less than eight weeks, well within the tune window available. Comparison of very extensive pre and post-blast condition surveys revealed no damage to the existing structures on Parliament Hill as a result of these operations.

Jan 1, 1999

By J J. F Smith

The application of pneumatically loaded ANFO for underground mining has continued to increase year by year since the technique was first developed and introduced underground during the early 1960's. Improvements in the manufacturing process for explosives grade prills, the design and construction of more efficient AN prill-fuel oil blending equipment, and the introduction of more durable and reliable pneumatic loaders have promoted the wide application of the relatively low cost blasting agent, ANFO.

Jan 1, 1982

By John Wright

As part of the redevelopment of the Royal Brisbane Hospital complex in Australia, a number of antiquated buildings were to be demolished and replaced by newer, modem facilities. Aside from the decommissioning of the hospital buildings, the project called for the removal of approximateIy 24,000 bank cubic metres (bcm) of varying quality rock material. Given the sensitivity of the project, in particular the close proximity of the required excavation to the existing hospital structures (-3 metres at the closest point), and the requirement that these were to remain lily operational during the construction phase, it was initially proposed to use hydraulic rock hammers as the primary means of excavation. Poor production rates and unexpected dif3icuIt rock conditions led to a revision of the excavation methods and a feasibility study on drill and blast practices was undertaken. Subsequent to an initial series of trial blasts to illustrate that vibration and flyrock could be adequately controlled, drill and blast methods were used in conjunction with mechanical methods of rock breakage. This paper reviews the drU and blast processes and the practices which were necessary to comply with the multiple constraints imposed on the project. The project has highlighted that modified drill and blast practices remain a cost-effective method of excavation, even in sensitive areas which are commonly deemed inappropriate for such methods.

Jan 1, 2000

By Scott King, Norm Patterson, Ruilin Yang

The multiple blasthole fragmentation (MBF) model developed by Orica models the contributions from multiple blastholes to fragmentation at any given point in the rock and simulates a production blast with the actual geometry of the blasted overburden and free faces, explosive loading, multiple decking, and delay timing of each explosive charge. The model has been successfully applied to several open pit mines and quarries around the world, including Canada and the United States. The peak particle velocity (PPV) induced in the rock from the explosive detonation is used in the MBF model as the key parameter relating to the size distribution of the rock fragmentation. Relating the PPV to the rock fragmentation is based on earlier work relating the particle velocity to the dynamic strain in rock. A recent publication further revealed that the PPV is related to the maximum relative displacement that induces three dimensional strain at a point in the rock. The model can explicitly model most of the blast design parameters including explosive properties.

Jan 1, 2018

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer

The environmental problems such as vibration, and air blast are often faced, and discussed on mining, quarrying, civil constructions, shaft-tunnel, pipeline, and dam operations where blasting is inevitable. It is necessary to establish national standards towards to minimize the environmental problems induced by blasting and judicial matters in our country as it is in USA, EU countries and the other developed countries. This necessity and the obligatory of accepting the European Union criteria for Turkey that has started the procedure of joining to EU emphasize the importance of this study. In other words, the establishment of a particular national standard related with this subject is inevitable for Turkey. This will be possible only by studying, applying scientific methods and techniques by the experts.

Jan 1, 2010

By Adrian Moore, Alan Richards

"It has been common practice to set blast vibration limits for structures using an “observational”approach whereby limits are set at a level based on observations of damage, or the lack ofdamage, combined with a tendency to further reduce the permitted level due to uncertainty. Suchan observational approach was used in the USBM RI 8507 to produce the frequency dependent‘Safe Levels of Blasting Vibration for Houses’ which has become a universal Standard for overthirty years."

Jan 1, 2013

By Virgil J. Stachura, Calvin L. Cumerlato

The U. S. Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of tests using a low-density water gel to improve the quality of air-decked presplit blasts at a surface coal mine in New Mexico. The explosive's specific gravity averaged 0.50 and was bulk loaded using a modified truck which injected the gassing agent. Reductions in overbreak and resulting rockfall were achieved in comparison to a highwall presplit with ANFO. The test sections used 15° angled blast holes and resulted in 1,119 m (3,672 ft) of air deck presplit highwall using a low-density water gel which was then compared to 894 m (2,934 ft) of highwall shot with an ANFO air decked presplit design. The total quantity of explosives per hole ranged from 68 to 113 kg (150 to 250 lbs) and the 27 cm (10-5/8in) holes were 19- to 33-m (62- to 108-ft) deep on 5.5 m (18-ft) centers. Periodic visual examination and photographic surveys of the highwall test areas were used to document the amount of rockfall. In addition, laser profiles of selected sections were conducted to further delineate the damage and highwall contour differences.

Jan 1, 1995

By María Rocha, Benjamín Cebrián, Roberto Laredo

"Ring blasting designs have to achieve different goals in order to become efficient whether is done in up hole or downhole fashion. Ore recovery/dilution control, fragmentation and drift integrity all have to be taken into account when selecting parameters such as burden, spacing, linear explosive density and stemming. Blast energy simulation allows identifying contours of rock breakage and fragmentation, thuschoosing a combination of spacing at the end of holes and appropriate burden. Also, simulations are keyto concentrate energy levels on the mid part of the ring while making sure there is not too high of energy concentration around the drift, which integrity is needed for a safe ore mucking."

Jan 1, 2017

By Reinhold Daykin, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e., metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine.

Feb 1, 2020

By Tyler Rockley, J. P. Remi Proulx, Ruilin Yang

A highwall blast vibration project was carried out to quantify the level of blast vibrations produced from a trim blast in soft rock and a combined production and trim blast in hard rock. Combining production and trim blasts could be performed without exceeding the mine’s vibration limits.

Feb 1, 2020

By Tyler Acorn, Paul Worsey, Nathan Rouse

The effect of the hole diameter on vibration attenuation has not been incorporated in most vibration models in the blasting industry. In current vibration models, the charge weight and the distance from the blast are the two primary variables that are addressed. Charge weight is a function of explosive density, charge length, and charge diameter. This geometry-weight can complicate the isolation of the charge diameter variable.

Jan 1, 2013