Search Documents

By B. M. P. Pingua, M. Nabiullah

Number of mine accidents occurred in Indian surface mines are due to poor quality of explosives and blasting accessories. Amlori open cast project is one of the major coal producing projects in India. Standard drilling and blasting parameters are used to achieve desired productivity of the mine. 150 and 260 mm diameter blast holes are used for blasting in coal and overburden benches. Most of shovel benches are 12 to 16 m in height and dragline benches vary from 25 to 30 m. High-energy bulk emulsions are used for blasting. The cup density and velocity of detonation of bulk emulsion explosives are 1100 to 1200 kg/m3 and 3.8 to 4.5 km/s respectively. An incident occurred on fire bench of Amlori open cast mines during mucking of blasted muck.

Jan 1, 2008

By L. Muñoz, L. Steffen, J. Alarcón, W. Vilas

Today, mining operations close to communities face increasing challenges, especially in their drilling and blasting operations. Proper management of environmental impacts is important to guarantee their license to operate and to provide sustainability to the mining business in the long term. Blasting is an event that generates impacts such as vibrations, noise (airblast), projections (flyrocks), ejection of dust and fumes (when there is a deficient detonation of the explosive). If any of these variables exceed the established regulations, sanctions can be generated and even lead to stop mining operations. The goal of this work is to present a review of different techniques, concepts, technologies, simulation software and monitoring / control tools to minimize the environmental impact generated by blasting. For which, a case study of a big scale open pit mine in Brazil with operations close to a community will be presented. An adequate management model, combined with good operational practices, the use of new technologies, enable a safe operation without incidents with the communities. In this way, building trust with neighbours, maintaining the license to operate, and helping mining industry to mobilize resources essential for progress in a sustainable way

Jan 1, 2024

By W. Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due to quarry blasting.

Feb 1, 2020

By Tom Snyder, John Brulia

PART 3 – UN Identifi cation Markings for the Highway Transportation in Commerce of Bulk Explosives, Oxidizers, and Combustible Liquids

Jan 1, 2015

By Chris Vagasky

On July 10, 1926, lightning struck at Picatinny Arsenal, New Jersey, and caused the explosion of at least 600,000 pounds (272,000 kilograms) of ammunition, resulting in more than $600 million (2015 dollars) in damage, the destruction of 200 buildings, and 22 deaths. Fortunately, there has not been a major incident involving lightning and explosives in the US in some time, though lightning has destroyed fuel storage tanks in recent years, including in North Dakota, Texas, and Ohio. Lightning poses a significant hazard to the explosives industry. Carrying high currents and temperature, lightning can cause explosives to detonate, start fires near storage facilities, and injure or kill operators.

Jan 1, 2017

By Vitor Fonseca de Barcelos, Jair Carlos Koppe

Our society is experiencing a digital revolution. Technology is demonstrating its significant potential for mining industry. In this paper are presented the measured and estimated impacts of applying new technologies on blasting operations in a copper mine.

Feb 1, 2020

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By Carlos Enrique Arroyo Ortiz, Jadir Pedro Alves

This paper presents some of the results obtained during the research work about the use of technologies and digital transformation in the process of rock drilling in open pit mines. The use of automation presents itself as a disruptive factor and a driver of improvements that provide sustainability in rock drilling. Seven main operational parameters were utilized to combine measurement while the drilling (MWD) with other information generated by the equipment during hole drilling, in six different lithologies in an iron mine, located in the central region of Minas Gerais in Brazil. Adjustments and corrections were made to the data collected in order to minimize external influences other than the rock itself, to ensure the effectiveness of the analyses. Finally, we sought to compare the performance of the drilling process in manual and automatic operation modes. Thus, making it possible to show the efficiency and impact on the sustainability of rock drilling operations in open pit mines.

Feb 6, 2023

By David La Rosa, Matthew Craft, Lee Julian

Rules of thumb are ubiquitous in blasting. Typically presented as ratios, they assist with the initial assumptions of blast design and provide guidance for best practice. Examples include the blast hole diameter as a function of bench height, and stemming length as a function of hole diameter. The most common rules of thumb were developed in mid-20th century and it is important for a blaster to know if the rules of thumb are still reliable.

Feb 6, 2023

By Lon Santis, David Leidel, John Tatom, Meredith Hardwick

This paper describes the development and methodology of the Institute of Makers of Explosives’ Safety Analysis for Risk (IMESAFR), a risk analysis software program for commercial explosives operations. IME is a nonprofit safety and security association devoted to the safe and secure manufacture, transportation, storage, and use or disposal of commercial explosives in the US and Canada since 1913. The software methodology’s basis is the U.S. Department of Defense Risk Based Explosives Safety Criteria Team’s Safety Assessment for Explosives Risk (SAFER) software. A diverse group of industry and government experts contributed to modifications to SAFER that reflect commercial operations. IMESAFR is intended to supplement the American Table of Distances (ATD) and offer standardized methods of managing risk from a wide variety of commercial explosives operations where the ATD does not apply. The modifications made to SAFER primarily involved the addition of commercial activities and potential explosives sites (PES). A review of commercial explosives accidents and operations over the last 20 years served as the basis for establishing probability of event values. An industry survey of commercial PES types in the U.S. and Canada was conducted to identify and address critical differences in commercial structures as compared to the military structures in SAFER. The paper concludes with discussion of the potential uses for quantitative risk analysis (QRA) and a description of other explosion effects software

Jan 1, 2007

By Paulo Couceiro, Juan Navarro

The impact of rock blasting fragmentation and heave on digging performance in open-pit mining operations is usually the first true indicator of blasting outcomes. Within the typical excavation cycle, the bucket loading time or instantaneous digging rate are the ones that present the strongest correlation with rock fragmentation size distribution, swelling, and shape of the muckpile, a part of rock mass hardness, equipment size, power, and others. As the efficiency of unit operations becomes increasingly important for long-term mining strategies, cost-effective approaches are needed to increase mine productivity. In this line, the performance of downstream operations, such as digging, hauling, and comminution, may be affected by the energy input in blasting. This requires a better understanding of the explosive’s energy role in such unit operations in order to drive consistent improvements. Therefore, this paper examines the impact of the explosive’s energy distribution on shovel diggability from production shots carried out with different explosives in an open pit gold mine, with the aim of modelling the interface between blasting and excavation.

Jan 21, 2025

By O Omidi

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper reviews previous experimental information and presents the results of new tests conducted in small blocks constructed using a commercial grout. The effect of the delay on the average fragment size, coarse fragmentation and uniformity of fragmentation is discussed. Fragmentation was coarser at extremely short or extremely long delays, while a fairly constant average size was obtained at a variety of intermediate delays. Uniformity, defined as the slope of the fragmentation distribution through the average fragment size, was poor at short and very long delays and relatively constant at the intermediate delays. Some tests attempted to minimize the effect of gas penetration by lining the boreholes with copper tubes. When this was the case average fragmentation changed marginally, while uniformity was significantly affected by delay and was typically smaller than in the unlined tests.

Jan 1, 2014

By Catherine Johnson, Barbara Rutter, Phillip Mulligan

Shock tubes, shock tunnels, and blast tubes have been widely used by explosive researchers and shock wave investigators to understand the characteristics of shock waves. Rectangular, cylindrical, and conical are the three simple geometries commonly used in shock tube and shock tunnel testing. These geometries result in shock waves that resemble the Friedlander curve’s simple exponential decay. However, geometries that are more complex have not been studied. This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile. Shock wave profiles were measured inside and outside the LATS to investigate the geometry’s effect. A representative shock wave profile from each geometry and open-air explosive testing were compared visually showing the geometries effect on the shock wave profile. The LATS produced a waveform with four pressure peaks behind the initial shock front, which were found to be associated with the four rectangular sections. The resulting pressure trace was compared to pressure traces from simulated urban bombings. The number of turns in an urban environment equated to a new peak, which is caused by additional expansion sections of the shock tunnel. From this observation, complex geometry shock tunnels can be purpose built to simulate an explosion in an urban setting. The use of shock tunnels with complex geometry in simulating urban bombings can allow for numerous representations and a better understanding of profiles produced during an urban bombing or similar scenario.

By Tom Paynter

In an underground mining environment, the primary method of firing a blast is using a combination of an electric detonator and a detonating cord to initiate the Nonelectric detonators. This method has been in use since the 1970’s. A firing line is used which can be subjected to damage and the need for constant testing and maintenance.

Jan 1, 2017

By Johan Hawinkel

This paper explores the journey through time of technology in the civil explosives market to provide testing, measurement, analysis and control tools. This ultimately leads to better decision-making, ensures full accountability of the decision maker and uses the same technology to review decisions for process improvement, in the settlement of disputes or for the investigation of incidents. Additionally, the paper discusses the application and integration of electronic and digital technology in explosives and initiation systems as engineering controls for blasting associated risks.

Feb 1, 2020

By Barbara Rutter, Phillip Mulligan

This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile.

Feb 1, 2020

By Steve Dillingham

A blast site incident has just occurred. Tensions are high, and, as the blaster, you’re in charge of the crisis at hand. Your mind is reeling, your thoughts frantic. The main areas of concern for you at the scene are to deal with immediate problems...aid the injured, take a head count, assess the damage, call emergency response, contact company headquarters, calm the neighbors, update your customer, and respond to the press on site. You feel as if all the bases have been covered...but, then again, have they? One of the biggest mistakes blasters and their companies can make is not including their Insurance carrier in the critical on-site accident procedures and emergency call list. Unfortunately, many companies believe that they are immune to the perils that can often, within a matter of minutes, create chaos that only happens to someone else.

Jan 1, 2002

By Mark S. Stagg, David E. Siskind

The Bureau of Mines arranged to have a wood-frame test house built in the pat of an advancing surface coal nine so it could investigate the effects of repeated blasting on a residential house. Structural fatigue and damage were assessed over a 2-yr period. The house was subjected to vibrations from 587 production blasts with particle velocities that varied from 0.10 to 6.94 in/s. Later, the entire house was mechanically shaken to produce fatigue cracking. Failure strain characteristics of construction materials were evaluated as a basis for comparing strains induced by blasting and shaker loading to those induced by weather and household activities. Cosmetic or hairline cracks 0.01 to 0.10 mm wide occurred during construction of the house and also during periods when no blasts were detonated. The formation of cosmetic cracks increased from 0.3 to 1.0 cracks per week when ground motions exceeded 1.0 in/s. Human activity and changes in temperature and humidity caused strains in walls that were equivalent to those produced by ground motions up to 1.2 in/s. When the entire structure was mechanically shaken, the first wallboard tape joint crack appeared after 56,000 cycles, the equivalent of 28 yr of shaking by blast-generated ground motions of 0.5 in/s twice a day.

Jan 1, 1985

By C E. Johnson, S Hosein

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as a consequence of the shock wave created by the detention of the explosive charge in a blast hole. In an attempt to evaluate these hypotheses, an investigation was undertaken over a 4-year period with the aim of determining the precise origin of air overpressure. The research was carried out at a chalk quarry in the North of England.

Jan 1, 2017

By Davey Bickford, Johan Hawinkel

Blasting and the use of civil explosives are a critical step in the mining process. Good decisions provide significant downstream benefits and create a safe and sustainable working environment, while poor decision making and judgement can have catastrophic consequences on workers safety, critical infrastructure or the security of the general public. An ever-tightening regulatory framework increasingly exposes manufacturers, transport companies and mining companies to the consequences of breaches resulting from erroneous or ill-informed decisions. In this context, new capabilities are required providing all actors in the explosive supply chain with tools to make better informed decisions allowing the individual to own up to his or her decision. Additionally, the traditional risk-control approach in the explosive supply chain up until usage and waste elimination, through administrative control procedures and processes, is becoming increasingly inadequate. In this era of digitalisation and automation, technology will play a pivotal role in ensuring safety and security in storage, transport and usage of civil explosives using the latest advances in electronics, communication technology and information technology. This paper explores the journey through time of technology in the civil explosives market to provide testing, measurement, analysis and control tools. This ultimately leads to better decision-making, ensures full accountability of the decision maker and uses the same technology to review decisions for process improvement, in the settlement of disputes or for the investigation of incidents. Additionally, the paper discusses the application and integration of electronic and digital technology in explosives and initiation systems as engineering controls for blasting associated risks. Finally, this paper reviews two practical cases of technology integration for risk management and improved decision making; the use of integrated GPS technology in initiation systems as an engineering control in the blast evacuation process and the use of RFID technology in explosive tracking from cradle to grave.