Search Documents

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By A. Karadogan, G. Tuncer, A. Kahriman

Determination of optimal blast parameters have been the priority act for blasters on the field due to financial and technical properties of the operation. Therefore many researchs were done to establish a general formula for many years. These intends could reach some empirical and numerical design frames consisting the rock, geology and explosives properties. Blasting parameters have to be adjusted according to the desired fragmentation rate especially on the mines where particle size distrubition after blasting has a great importance. Therefore the blast designs have to be evaluated considering the particle size distribution after the blasts. The Kuz-Ram model which was modified by Cunningham is one of the tools for estimating the particle size. Although it doesn’t give an accurate result, it can be very succesful on modifying the blasting design parameters by establishing a back correlation between the blasting parameters and the exact particle size distribution results which can be easily achieved by digital image processing system. Within the scope of this study, the particle size distribution after blasting was assessed by Split-Desktop digital image processing system and bench blasting parameters were studied considering the desired particle size distribution at Espey colemanite mine using Kuz-Ram and digital image processing system combination to determine the specific blasting parameters for this site.

Jan 1, 2005

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Finn Ouchterlony, José A. Sanchidrián

"A model for fragmentation in bench blasting that originates from dimensional analysis of fragmentation in asteroid collisions is presented. Percentiles of the size distribution are obtained in the basic model as the product of a rock strength-to-explosive energy ratio, a bench shape factor, a scale factor or characteristic size and a percentage passing-related factor. The parameters of the model are fitted to 169 bench blasts in different sites and rock types, bench geometries and delay times, for which thefragmentation of the muckpile was obtained by sieving. The basic model is found to significantlyimprove with an additional factor describing the rock mass structure in terms of the spacing and orientation of discontinuities, and another one describing the delay between successive contiguous shots; the latter is conveniently formulated as a function of the P-wave velocity and the holes spacing. The rock strength property chosen is the strain energy at rupture that, together with the explosive energy density in the rock (or energy powder factor), forms a combined rock strength/explosive energy nondimensionalfactor. The model, called xP-frag, is applicable from 5 to 100 percentile fragment sizes, with all parameters determined from the fits significant to a 0.05 level. The expected error of the prediction is below 25 % at any percentile. These errors are half to one third of the errors expected with the best prediction models available to date."

Jan 1, 2017

By M. Ganster, H. Krenn

The mission of the project is the fast and cost-effective rehabilitation of decommissioned lignite mining and coal upgrading facilities. This is necessary to ensure the successful future utilization of these sites. On the one hand, for founding new industrial and commercial facilities and on the other hand for touristic activities.

Jan 1, 2013

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By Catherine Aimone-Martin, Mary-Alena Martell

Whole-structure and mid-wall responses of 33 non-traditional structures to surface coal mine blasting were characterized. Eighty-nine blasts were conducted at 11 mine sites throughout the U.S. to measure blastgenerated dynamic response of structures typically found in the proximity of surface coal mining. Structures selected for this study include log-type, manufactured (single- and double-wide trailers), “mine camp”-type, adobe, and stone. Traditional acoustic microphones, t&axial (ground) and single component (structure) velocity transducers were used to record airblast, ground motions, and structures response time histories with a common time base. Wall crack displacement gages were used to record static and dynamic movement of existing drywall cracks. The relative responses of selected “atypical” structures to blast vibrations and nonblasting causes of structural stress, including natural forces, environmental effects, and human habitation, are compared. The purpose of this study is to document and compare vibration characteristics of structures that were not included in previous studies conducted by the U.S. Bureau of Mines and others in establishing the widely adopted safe level blast vibration criteria in the U.S. An important objective of this study is to outline an evaluation process including structure uniqueness relative to cracking susceptibility.

Jan 1, 2002

By Robert Boehnke, Bernd Mueller

Despite enormous efforts over the last decades there are still many unanswered questions with respect to calculation and modeling of the blast process using appropriate physical laws. Most calculations of explosive charges of a blast design are based on experience, empirical observations or blasting theories with serious shortcomings. This paper presents a new theory for the design and calculation of a rock blast that is based on the momentum. It offers a clear-cut method for the calculation of blast processes. The theoretical results will be compared with on-site measurements by means of a newly developed strain sensor and further measuring equipment. The momentum theory helps better to explain physically the processes of a blast. On the basis of long-term statistical investigations a momentum balance can be carried out with the volume-based blasting momentum and the measurable momentum associated with the muckpile and the remaining rock mass. This type of consideration requires a complex procedure which includes the blastability of the rock masses. Realis tic strain measurements open a new interpretation possibility and judgment criteria for the most probable building damage, the dynamic impact on general types of buildings and also for the blast process itself. The blast-induced stress and the momentum generated could be back-calculated using a geophone profile and the strain sensor. The strain owing to a dynamic impact can be influenced by the changing of the drill-, blast- and shotfiring technique like the until now measured vibration velocity. In this way it is possible today to make a complex preparation, calculation and evaluation of blasts. The new techniques of measuring in connection with the momentum theory bring about an increase of the safety and a clearcut method of improving the blast processes. This procedure offers new possibilities for the precise calculation, simulation and modelling of blasts and resulting vibrations and leads to an increase of the safety as well as economic adaptation of the drill-, blast- and shotfiring techniques to a pre-determined blasting result.

Jan 1, 2003

By Dale Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was first attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The configuration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the first four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition.

Jan 1, 2006

By Joshua Hoffman, Braden Lusk, Kyle Perry

This study explores how different geometries affect the shock tunnel’s performance and is broken down into three phases. Phase 1: Open arena testing in which theoretical energies produced by the detonation of small (<1.0 kg) charges are compared to actual experimental values. Phase 2: Shock Tunnel testing in which realized energies are experimentally recorded for the UK and S&T shock tunnels. Phase 3: Analysis of the data to begin building a pressure-forecasting tool for the UK shock tunnel given the explosive characteristics, sample size and desired pressure and impulse.

Jan 1, 2009

By Charles Zdazinsky

"The Multiple Seed Waveform (MSW) blast vibration model, a type of waveform superpositionmodeling developed by Orica Inc., uses vibration data that is collected from a signature hole blast tocharacterize the ground’s seismic properties and determines the ground resonant frequency andfrequency range that is well supported by the ground. Additionally, the MSW model uses thisvibration data as input parameters to predict the resultant dominant frequency of a production blast. This information may in turn be used in conjunction with precise timing control to target theoptimum dominant frequency which promotes ground control."

Jan 1, 2016

By Sarma S. Kanchibotla

In overburden cast blasting the explosive energy is used to move a significant percentage of overburden from the high wall to the spoil pile thus reducing the amount of material to be handled by machinery. However, the obvious trade-off between the extra explosive energy in the cast blast versus reduced dragline effort is complicated by an increased risk of damage to the underlying coal. This damage may not be obvious but inevitably leads to reduced coal recovery and may negate much of the benefit sought from cast blasting.

Jan 1, 1999

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.

By M. Hagfors

When establishing an underwater testing site for the energy measurements of the explosives, the dimensions of the measuring pool have to be measured to find out what is the maximum weight for the test charge. Secondly one has to decide the distance between the pressure gauge and the shooting point. Thirdly the pool has to be calibrated because of the reflections of the explosions by measuring the bubble periods of the calibration charges. The calibration shots can also be used to estimate the minimum weight of the explosive charge for the reliable energy measurements by calculating the shock, gas heave and total energy values and their standard deviations.

Jan 1, 2007

By Thierry Bernard, Phillipe Cappello, Jean Marc Laboz

"The main reasons of the emergence of electronic detonators are linked to:-Local urban development close to mining operation sites-Environment regulations"

Jan 1, 1995

By H Ulrich Leiste, Leslie Talor

This paper describes a series of small scale tests conducted to investigate the loading applied to a flat plate by the detonation of a cylindrical charge very close (between two and three charge radii from the center of the charge) to the structure. The testing used very small quantities of explosive (PETN): Two different series of tests were conducted. In the first test series, impulse loading on the target plate was investigated using three different sizes of charge. In the second series, pressure time profiles were determined. The charge size was 6 g or less. Impulse was found using high speed video of the target plate to determine its displacement as a function of time, from which initial plate velocity was obtained. Kolsky Bars, placed at the same distance from the charge as the target plate, were used to determine the free-field pressure time profile of the output of the charge at this distance. Two different types of target plates were used in the impulse study. One was just a plate while the other was a plate constrained with a steel frame.

Jan 1, 2009

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

By Kristen Dunlap

There are several thousand remote stream crossing structures in the Tongass National Forest in need of removal. In 2007 thirty-three collapsing log bridges, log culverts, and metal culverts no longer in use were removed with explosives. Species of salmon, trout, char, and sculpin are present in the project area. Blasting overpressures may injure or kill fish in streams and ground vibrations can damage salmonid embryos in streambeds. Regulatory agencies offer guidelines with limits for blasting induced overpressures and vibrations. However, there has been no quantification of blast overpressures in shallow streams. Methods used to predict lethal levels for various blasting applications have not been completely validated. This research provides guidance for analyzing ground vibrations and water overpressures during blasting activities in or around fish streams.

Jan 1, 2009

By Quentin Rhoton

To benefit two endangered fish species, waterfowl and other wildlife, and water quality in the lake and downstream, the decision was made to remove levees that had been in place since the 1950s. Because the levee material was mainly dredged up lake bottom peat, it was decided to pare down the sites chosen for breaching with dozers and trackhoes. This material was spread out onsite instead of expensive removal by dumping elsewhere. Because of the instability of the final pared down levees and the lake level being at a ten-year low, it was decided to use explosives to breach four of the sites. After over five months of earthmoving and two weeks of loading holes, the levees were detonated the day before Halloween, 2007. Somehow pumpkins showed up to be part of the explosive activities.

Jan 1, 2009

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018