Search Documents

By Lloyd A. Morley

Proposed advantages and disadvantages of low-voltage shielded trailing cables are formulated utilizing the literature and industry sources. A partial analysis of these proposed advantages and disadvantages is completed through a review of the literature. Cable costs are assembled from mine operators, cable and splice manufacturers, and actual cable purchases. To confirm each advantage and disadvantage, an underground test site is established, and testing is performed here and in the laboratory. All testing procedures are completely described. The results of this investigation are reported and used to formulate recommendations attendant to low-voltage shielded cables. Suggestions for installation, handling, and maintenance are presented.

Jan 1, 1977

By Ronald B. Stotelmeyer

This report summarizes studies of 55 Idaho national forest roadless areas completed by the U.S. Bureau of Mines (USBM) in the period 1966-1992. These roadless areas have been recommended for addition to the National Wilderness Preservation System, proposed as special management areas, or otherwise recommended for study by the U.S. Forest Service or the Idaho congressional delegation. The Bureau of Mines' studies indicate which parts of the roadless areas contain mineral resources. They also show where mining and prospecting are likely to occur in the future, where mineral production has occurred in the past, and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character.

Jan 1, 1994

By Robert H. Peters

How can employees be stopped from engaging in unsafe work practices? It is often easier to prevent employees from performing unsafe acts through manipulations of the work environment than through various training or motivational programs. Therefore, it is important that accident prevention programs seek to identify the reasons for the unsafe behavior and to redesign tasks and the work environment (e.g., tools, equipment, physical surroundings) in order to remove employees from sources of harm and to prevent situations from arising that would prompt them to perform unsafe acts. Unfortunately, in the mining industry the work environment is often innately hazardous, rapidly changing, and difficult to predict, making it very difficult, perhaps impossible, to fully protect the employee by environmental manipulations. Therefore, it is important that effective methods be identified for influencing mine employees to work safely. Various strategies have been used to convince employees to avoid unsafe acts and/or adopt self protective behaviors. The intent of this article is to provide guidance to mine operators concerning the use of four techniques for influencing mine employees to work safely: (1) employee surveys, (2) incentives, (3) fear communications, and (4) disciplinary actions.

By Victor R. Spironello

Applications of three experimental design techniques to smelting operations are explained. The report describes a factorial design using three variables at two levels, a fractional factorial design which investigates seven variables, and response-surface methodology for optimization of electric- furnace smelting processes. These methods may be applied with a minimum of trials and at little expense. Further, the writer knows of no reasons why the same methods could not be applied to other operations as well, such as steelmaking.

Jan 1, 1970

By M. Carrales

This Bureau of Mines report presents information on the sulfur content of crude oil in the United States and in some foreign countries. Data are presented for oil produced in 1971 from fields in 26 States that accounted for about 76 percent of total U.S. oil production; the foreign data cover fields in 24 foreign countries that accounted for about 64 percent of the total oil produced from these countries in 1971. Most of the data are presented in tabular form.

Jan 1, 1975

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By John R. McWilliams

This report is one of a series published by the Bureau of Mines describing methods and practices at various mines throughout the United States. A previous program, conducted from 1928 to 1939, was well received by the mining industry and technical institutions and provided much source material for engineering textbooks and technical handbooks. The stringent wartime demands on the mining industry, the rapidly changing postwar economic situation, and greatly accelerated technologic growth have combined to render many of the previous data obsolete. The objective of the present program is to assemble reliable technical information on mining methods and practices throughout the country and present it for the use of the mining industry, technical schools, textbook authors, and other interested persons. This report deals with the design and development of the Berkeley open- pit mine at Butte, Mont., owned and operated by The Anaconda Company. The Berkeley pit is but one facet of a well-organized and integrated copper-mining operation involving the entire Butte district. Vein-type mining, important for 75 years, is still in progress at depths from 600 feet to nearly 1 mile; on intermediate levels, low-grade ore left untouched by earlier vein-type mines is being extracted by block caving entire ore zones,3/ and secondarily enriched but lower grade near-surface portions of the same ore zones are being mined by open-pit operations (fig. 1). The Berkeley pit itself is named for the Berkeley mine, one of the old mines that extracted copper ore from high-grade veins in the area that now will be mined by open-pit methods.

Jan 1, 1959

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 25 jurisdictions of East Asia and the Pacific. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1971

By L. A. Morley

Volume IV of the final report examines the problem of indirect contact of overhead high-voltage power lines by mining personnel. This refers to the contact of energized lines by workers through some intermediate conductor such as a metallic tool or a piece of high-reaching mobile equipment, thus the term "indirect contact." The shock hazard presented by such contact has been a major cause of electrical fatalities associated with mining operations. The report volume is divided into three major areas. The first gives a general background of overhead lines, basic characteristics, and associated hazards, and continues to describe presently used techniques and devices which attempt to alleviate the contact problem. The second area narrows the discussion to the mining industry by presenting a detailed analysis of 39 overhead-line contact accidents in mining since 1970. The third major section uses the information from the first two areas to formulate recommendations to prevent these accidents and subsequent electrocutions at mining operations.

Jan 1, 1982

By Thomas P. Mucho, Dennis R. Dolinar, Anthony T. Iannacchione

The Chestnut Ridge Anticline is a prominent structure in southwestern Pennsylvania, USA. This structure has brought two economically valuable limestone formations to the surface, where they are easily accessible to room-and-pillar mining. Nine active crushed stone quarries, an underground research facility, and one industrial facility currently operate along the linear trend that represents the axis of the anticline. The National Institute for Occupational Safety and Health (NIOSH) has identified significant variation in levels of horizontal stress within relatively short distances at shallow overburdens along the anticline. At one quarry, the horizontal stress is high enough to shear strata with a modulus of approximately 77 Gpa. Conversely, zones of extension were observed in parts of another quarry, indicating very low horizontal stress conditions. This study found that high levels of horizontal stress are to be expected in this very stiff rock formation and that local geologic and topographic structures are capable of altering the magnitude and possibly the orientation of the horizontal stress field.

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the fourth report of investigations dealing with the cooperative tests between the Bureau of Mines and industry on the use of electrolytic manganese in steelmaking. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steel 3/ the second with its use in acid electric steel practice, 4/ and the third with its use in low-carbon basic open-hearth steelmaking. 2/ A résumé of those investigations E7 appeared in the magazine STEEL. 5/ The present report deals with the use of electrolytic manganese in the manufacture of four types of stainless steel and the new Timken 16-25-6 alloy. The Bureau of Mines supplied The Timken Roller Bearing Co. with 62,000 pounds of electrolytic manganese for use in the tests.The electrolytic manganese was produced at the Bureau of Mines pilot plant, Boulder City, Nev., by the process developed by the Bureau and described in Bulletin 463, Operation of Electrolytic Manganese Pilot Plant, Boulder City, Nev., by J. H. Jacobs. J. W. Hunter, W. H. Yarroll, P. E. Churchward, R. G. Knickerbocker, R. W. Lewis, H.A. Heller, and J. H. Linck. The workcarried out under the direction of R. S. Dean, formerly assistant director, Bureau of Mines, and R. G. Knickerbocker, formerly chief, metallurgical branch, as part of a long-range program involving the development, manufacture, and use of manganese from domestic ores. Preliminary arrangements for the plant tests were made by the late A. A. Dow. 7/"

Jun 1, 1947

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By R. R. Sayers

A series of coal- mine catastrophes in the latter part of the first decade of this century focused public attention on the need for safety in mines and resulted in the establishment of the Federal Bureau of Mines , whose primary function was to promote safety and improve hygienic conditions of workers in the mineral and related industries . These activities are carried out by the Safety Division of the Bureau's Health and Safety Service . In general , the work performed by the Safety Division personnel may be classified as educational and investigative . Instruction is given in accident prevention for mine officials and miners ; first aid to the injured ; the use and care of oxygen breathing apparatus ; and advanced mine rescue and recovery operations . A specialized safety course is offered to the petroleum and gas industries . Division personnel also aids in or directs rescue and recovery work after mine fires and explosions ; assists at first - aid and mine rescue contests ; conducts safety exhibits and demonstrations ; and presents safety talks , often accompanied by sound safety motion pictures or latern slides , before employee and official groups , at meetings of Holmes safety chapters , at mining institutes , and at other safety or technical gatherings . Coal - mine fires and explosions are investigated , as well as quarry or metalmine explosions and fires , miscellaneous accidents , health and safety hazards , and safety conditions at mines and plants ; safety devices are investigated and developed . Field studies cover ventilation , methods of allaying suspended coal - dust particles , prevention of dust accumulations , the proper use of rock dust to prevent or limit explosions , explosives practices , and the care and use of underground equipment . The results of these studies and investigations are widely applied in the various training courses and are prepared as reports and recommendations , which are submitted to interested persons or are combined and distributed to the public as bulletins , technical papers , miners ' circulars , information circulars , and reports of investigations . These studies also afford a basis for the development of new or modification of old Safety Decisions of the Mine Safety Board of the Bureau of Mines . The following pages review the accomplishments of the division as regards safety during 1942,2/ with like information for a series of recent years and summaries to date . A striking feature of the division's work has been the safety education of more than 1-1/2 million persons who have taken first -aid and mine rescue training courses . That these efforts over a period of 3 decades have been successful is revealed by the decline in coal - mine fatality rates and a somewhat smaller decrease in metal - mining and quarrying fatality rates .

Apr 1, 1943

By Jaan Kiusalaas

This report is a self-contained User Manual for a computer program called SPASID -- Subsidence Prediction and System Identification. The program has two primary functions: (i) Precalculation of ground movements due to underground mining operations using the influence function method; (ii) Computation of influence function and site parameters from measured displacements. SPASID is written in FORTRAN and consists of four modules: (i) Preprocessor Module that prepares and maintains surface and mine data bases; (ii) Subsidence Computation Module that predicts movements of the surface; (iii) System Identification Module which is used to calculate the optimal influence function parameters, and (iv) Postprocessor Module for generating graphic displays of subsidence data. The last module is somewhat machine dependent but has internal documentation to indicate potential changes. All of the modules may be run in either batch or interactive mode. The manual does not assume previous knowledge of the influence function method or programming competence.

Jan 1, 1983

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facilitate research on the fundamentals of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, but Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing adit has an advantage over an active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin in September 1936, with a crew of four laborers under a resident engineer. The laborers were recruited from nearby farms, and although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

By C. F. McCarroll

The effectiveness of an industry?s safety activities can be gaged best by the accident records of that industry. In an effort to gage conditions in the petroleum industry, and with the objective of helping to reduce the number of accidents in it, the Bureau of Mines from time to time has tabulated, analyzed, and published pertinent statistical information3/. These reports have dealt with distribution, causes, and costs and related phases of accidents for various and collective divisions of the petroleum industry in several sections of the country. This type of study aids the personnel of the Bureau in planning the course of its activities in accident-prevention work and gives useful data to persons engaged or interested in the promotion of safety in the petroleum industry, which will aid them in their efforts to reduce the number and severity of accidents. A majority of petroleum operators and ?service" contractors have acknowledged their responsibility to provide their employees with safe working conditions and to their stockholders for greater economic value of invested capital by establishing safety divisions within their respective organizations. Such divisions have a primary duty, namely, to see that properly designed and guarded machinery and working equipment are furnished the employees and that they are trained in the safest practical methods of performing their work. Some companies and individual operators, however, have shown little or

Jan 1, 1939

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By K. K. Kelley

The collection and correlation of thermodynamic data concerning substances of metallurgical interest have constituted one of the major activities of the Pacific Experiment Station of the Bureau of Mines, at Berkeley, Calif., for the past several years. Earlier bulletins (32, 33, 34, 36, 36, 37, 38) s in this series are entitled: (1) Contributions to the Data on Theoretical Metallurgy. I. The Entropies of Inorganic Substances; (2) Contributions to the Data on Theoretical Metallurgy. II. High-Temperature Specific-Heat Equations for Inorganic Substances; (3) Contributions to the Data on Theoretical Metallurgy. III. The Free Energies of Vaporization and Vapor Pressures of In¬ organic Substances; (4) Contributions to the Data on Theoretical Metallurgy. IV. Metal Carbonates--Correlations and Applications of Thermodynamic Properties; (5) Contributions to the Data on Theoretical Metallurgy. V. Heats of Fusion of Inorganic Substances; (6) Contributions to the Data on Theoretical Metallurgy. VI. A Revision of the Entropies of Inorganic Substances-1935; and (7) Contributions to the Data on Theoretical Metallurgy. VII. The Thermodynamic Properties of Sulphur and its Inorganic Compounds. The present paper collects and discusses thermodynamic data relating to metal carbides and nitrides, with the view of obtaining usable heat and free energy of formation relationships. Pertinent data on both classes of substances are difficult to obtain experimentally and consequently are extremely rare; it is therefore necessary in many cases, if equations are to be derived, to introduce certain approximations and assumptions. Lack of adequate means of checking results by utilizing data of different types, such as was done frequently in the bulletins dealing with carbonates and sulphates, are readily apparent to anyone who has made even a cursory examination of the available information. Consequently, some of the relationships derived undoubtedly will be found to be inaccurate when more or better data become available. Nevertheless, in view of the importance of some of these substances, it appears worth while to consider the information available at present and to attempt the formulation of as complete a

Jan 1, 1937

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

By Robert Vinson

This article examines the spatial variability of dust concentrations within a coal miner?s breathing zone and the impact of sampling location at the cap lamp, nose, and lapel. Tests were conducted in the National Institute for Safety and Health Pittsburgh Research Laboratory full-scale, continuous miner gallery using three prototype personal dust monitors (PDM). The dust masses detected by the PDMs were used to calculate the percentage difference of dust mass between the cap lamp and the nose and between the lapel and the nose. The calculated percentage differences of the masses ranged from plus 12% to minus 25%. Breathing zone tests were also conducted in four underground coal mines using the torso of a mannequin to simulate a miner. Coal mine dust was sampled with multi-cyclone sampling cans mounted directly in front of the mannequin near the cap lamp, nose, and lapel. These four coal mine tests found that the spatial variability of dust levels and imprecision of the current personal sampler is a greater influence than the sampler location within the breathing zone. However, a one-sample t-test of this data did find that the overall mean value of the cap lamp/nose ratio was not significantly different than 1 (p-value = 0.21). However, when applied to the overall mean value of the lapel/nose ratio there was a significant difference from 1 (p-value < .0001). This finding is important because the lapel has always been the sampling location for coal mine dust samples. But these results suggest that the cap location is slightly more indicative of what is breathed through the nose area.

Jan 1, 2007