Search Documents

By Ruth F. Brinkley

This circular describes the activities and publications of the Bureau of Mines, Explosives Research Laboratory4 for the fiscal year 1960 (July 1, 1959 -June 30, 1960). Part 1 describes briefly the principal projects that were active during the report period, and presents some data not scheduled for publication elsewhere in the near future. Certain of the results are only preliminary and should be regarded as tentative, pending the findings of the completed investigation. Publications that appeared during the report period are listed and described briefly in part 2. In general, the research activities reported in these publications antedate fiscal year 1960. The published material relating to activities that are still current is indicated by references in part 1.

Jan 1, 1962

By C. Fang, D. B. Kittleson, K. L. Rubow

"Under contract to the U.S. Bureau of Mines, a study was conducted to investigate the feasibility of using the microorifice. uniform deposit impactor (MOUOI) to measure the size distribution of aerosols containing various mixtures of coal dust and diesel exhaust particles. The project objective was to determine if the mass concentration of diesel exhaust particles, in an airborne mixture of coal dust and diesel exhaust particles, could be determined on the basis of the size distribution of the two aerosols. In general, the mass of diesel exhaust particles is in the submicrometer size range while that of the coal particles lie in the larger size ranges.The MOUDI is a cascade impactor with small diameter nozzles to obtain small cut sizes and rotating impaction plates to avoid particle overloading of the deposit. For this study, a 7 stage version was used. At the sample flow rate of 30 L/min, the cut sizes were 0.10, 0.23, 0.70, 1.0, 2.6, 4.9 and 10 pm.Size distributions of aerosols generated in the laboratory and in several underground coal mines were measured. The primary emphasize of the laboratory tests was to ascertain if the diesel exhaust particles could be separated from the coal dust, regardless of mass fraction of the diesel exhaust particles in the total aerosol mixture. Diesel exhaust, from a Caterpillar Type 3304 NA diesel engine, was mixed with coal dust generated with a· TSI Model 3400 fluidized bed dust generator. Experiments showed the size distributions of the mixed aerosols exhibited two definite modes with the minimum between the two modes in the 0.7 to 1.0 um size range. Distinct modal separation was obtained as the mixture fraction of the diesel exhaust aerosols was varied from 3% to 98%.The field study was conducted in three underground coal mines, two utilizing diesel-powered equipment and the third exclusively using electric equipment. Sampling sites were selected to obtain a wide variety in the diesel exhaust and dust aerosol concentrations. Size distribution data showed these aerosols are bimodal. The mass median aerodynamic diameters of the diesel particulate mode and the coal dust mode were approximately 0.15 µm and 3 to 10 un, respectively. The results, in all cases, clearly show a separation between the two modes in the 0.7 to 1.0 µm size range with the minimum in the vicinity of 0.8 pm. The separation was found to be independent of mass fraction of the diesel exhaust particles, total particle concentration and sampling site."

Jan 1, 1989

By James Westfield

This publication covers the work of the Division of Coal Mine Inspection, Bureau of Mines, as performed under provisions of the Federal Coal Mine Safety Act. It presents background information and data since 1952 when the Act became effective and includes up-to-date statistics for the calendar year 1962. During that year, approximately 9,704 coal mines were active in the United States, and the Bureau made 12,810 regular inspections. BACKGROUND The Federal coal-mine inspection program was established to carry out the provisions in Public Law 49, 77th Congress, (H. R. 2082) approved May 7, 1941. This act has since been amended as Title I, Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also included Title II, Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal Mine Safety Act.

Jan 1, 1963

By H. B. Carroll

This Bureau of Mines report evaluates the performance of commercially available portable instrumentation for the detection of carbon monoxide, carbon dioxide, oxygen, and methane at conditions simulating an industrial work atmosphere. Portable instrumentation included in the study was gas-detection tubes (length-of-stain and color intensity), catalytic detector, liquid absorption detectors, paramagnetic oxygen detector, galvanic detector, and pelement or hot-wire methane detectors. Evaluation of the instruments was in atmospheres with 50 and 80 percent relative humidities at 75° F and containing test gas concentrations of 0.1, 0.25, 0.50, 1.0, 1.5, and 2.0 times the thresh-old limit value. Correlation of the results from the portable gao analyzer with measurement from the standard instruments was made by calculating and plotting an estimated line of regression, prediction, and confidence limits and the correlation coefficient for each detector system. Relative humidity in the 50-to 80-percent range did not appear to contribute to instrumental uncertainties in either performance or operation. Considerable deviation in detection precision between the portable gas-detection systems and the standard systems was established, especially at the lower gas concentration levels. The main difference or inconsistency in toxic gas concentrations determined with length-of-stain tubes resulted from the observer's interpretation of the results rather than difference in the tubes themselves.

Jan 1, 1973

By James R. Cosby

This report describes work performed for the Bureau of Mines to evaluate available portable instruments for their effectiveness in detecting and locating damaged metallic shields in Types SHD and SHC cables. A second phase of the program is also covered wherein several instruments of a type which show promise are purchased for modification and testing to verify their performance.

Jan 1, 1980

By W. R. Crank

[Rock bursts are phenomena associated with mining operations, particularly with deep mining, although they occur throughout a wide rump, of depth, from 600 feel downward. The intensity is usually in direct proportion to the depth, varying from a loosening and sloughing off to a violent rupture, giving rise to the term, "explosive rock." The more or less violent breaking of rock in mine working, tins been variously designated as " flaking," "pressure hoists," "strain bursts," "bumps," "quakes," and "air blasts," which indicate opinions as to cause and effect. The term "air blast" lots probably beat most widely used, and naturally so, as a more or less rapid movement of air often accompanying the more violent phenomena of rock failure. Furthermore, there is an implied if not definitely expressed degree of magnitude in the action designited by a given term and in the cause and character of the action. For example. flaking, pressure bursts, and quakes are terms ranged to indicate action of increasing magnitude; and pressure bursts, strain bursts. bumps, and quakes are ranged according to the cause and character of the action.]

Jan 1, 1929

By F. E. Cash

"Explosions in bituminous coal mines are preventable. The combination of adequate ventilation, thorough rock-dusting, and water on the cutter bars of mining machines and of empty and loaded cars will certainly reduce the hazard to a minimum, if not remove it entirely. This is the attitude taken by the Woodward Iron Co. in lessening or removing the dust and gas explosion hazard from its Dolomite and Mulga mines.This report was made possible through the willingness of Frank H. Crockard, president of the Woodward Iron Co. to make records available and to authorize their publication for the benefit of the coal-mining industry.The compilation of these data and preparation of maps was facilitated by the cooperation of M. Heard, general superintendent of coal mines, J. B. Whatley, assistant general super-intendent of coal, and R. P. Whetmore, chief mining engineer.The Dolomite and Mulga mines are about 16 miles southwest of Birmingham, Jefferson County, Ala., on a company owned and operated railroad which connects ore mines, coal mines, coke ovens, and furnaces.In the Dolomite property there is a 30°, 860-foot, double-tracked slope for hoisting, three manway and air slopes and one air shaft, all in rock.At Mulga there is a 220-foot hoisting shaft, an air shaft and two manways, and material and air slopes, all in rock to the coal bed.The coal in both mines comes from the Pratt bed, which is the next coal above the Mary Lee bed in the Warrior Basin. The coal is horizontal or slightly undulating, with thickness varying from 36 to 72 inches and averaging 50 inches.The method of mining is essentially room-and-pillar with modifications for mechanized sections. The mines produced approximately 1,100,000 tons with 2,328,309 man-hours exposure n 1929 and 900,000 tons with 1,697,436 man-hours exposure in 1930.Through the work of the safety department the entire personnel in the coal mines, as well as in other departments, makes safety an essential part of efficient operation.Both mines are gassy; Dolomite produces about 334,000 cubic feet and Mulga about 919,000 cubic feet of methane every 24 hours.The ventilation maps, two of Dolomite mines (figs. 1 and 2) and one of Mulga (fig. 3) give as much of the details of ventilation as is practicable to put on maps of such scale. As will be seen from these maps there are two main ventilating fans in Dolomite mine and two in Mulga mine and the general direction of the air travel is indicated by long arrows to fan 1 and short arrows to fan 2 in each mine. Each fan has a gas or steam auxiliary drive and each mine has a complete fan and power unit ready for operation in emergency.In Dolomite, recently taken data show that fan 1 exhausts 82,000 cubic feet of air per minute at 3.2-inch water-gage pressure, with an analyzed methane content of 0.15 per cent, and fan 2 exhausts 115,500 cubic feet of air at 3.8-inch pressure and 0.10 per cent of methane. In addition, a Capell fan at No. 2 air shaft is a standby or emergency unit.In Mulga recently taken data show that fan 1 exhausts 83,000 cubic feet of air per minute at 3.0-inch pressure and 0.18 per cent of methane, and fan 3 exhaust 119,000 cubic feet of air per minute at 5.4 inch pressure and 0.35 per cent of methane. Fan 2 at No. 2 shaft is a standby or emergency unit for the Mulga mine.The ventilation is on a split system in both mines. All part split and total returns are measured, sampled, and analyzed weekly, requiring one man two days each week. During December, 1930, 77 samples were collected and analyzed in Mulga and 78 in Dolomite. Two weekly reports covering part of December, 1930, are given here so that they can be studied to show control of ventilation in the Dolomite and Mulga mines. In the event that a split sample shows more than 0.50 per cent of methane, immediate steps are taken to lower the explosive-gas content. The reports follow:"

Mar 1, 1932

By Richard A. Busch

Inadequate engineering design criteria for coal refuse embankments has allowed hazardous impoundment structures in coal mining areas to be created. A necessary first step to develop adequate design criteria is the determina¬tion of basic, respresentative physical property data on the materials that constitute typical refuse embankments. An extensive field and laboratory program was undertaken by the Federal Bureau of Mines. Much physical property data was generated. Additonal petrographic analysis and large scale triaxial compression testing was performed by others. The data presented here should aid in establishing design parameters for coal refuse embankments

Jan 1, 1974

By Dhanesh Chandra

[The U.S. Ucparunent of tlIe III LeriOr, Bureau of 1?Ilnes, lnta dcvcltil- (I a m.?tl,nd to extract nickel, i:ob.tll and IlIIicr Valuc:l,1, mrl?tl., lrom I.ow grad:, dumusI it Inlet itc.: :isin;; a rarb-i mnnnxid:: reducl.iun and ,innnonln/mumonlum sull,h.Ito Icitcll Col lowed by solved. evil let foil and clot tr:,winnfu,;. 'I 'o rain bcLtur undcI'sLandin;; uI the producLs reduced rind leached with the s;:Item, the liureau of t?Ilite; was enf,ngod In a 1 uinL sl.utly IIt1I the Uuttvcr ltc~:c:n-ch LnstiI-IL-. 'I'hr'ut;;h C(Im:drlod ahplit I¬L ion:; of a rotnbIW)L11nl ill eleu Lyon :utJ uplical inicrnscopy, cle trun beau micru,inal?;st?s and X-r.iv tcchnitlaes, Lhc factors jilt] ucncing low nickul e::lracl.on yLrids Iron, ccrlnin l;tteritos wul the hcuefhe al yCferL front addil.I:un u1. r:u)plowt' ruug,ounus and halides have bucn rrvealod. IL leas ht'en shown their nt nliJcrate Lion terlperuLuri's (5S0°C - 6501C) Lhe 111LACl extraction ylolds were low hccausc of the futmetlt-m of rufrill t,urv sillc:Ite compicxcs during ciii lit Hi [hut COOL.tlu sig nlficnnt anutunls of nickel .Lrui LhaL arc resistant Lu discolullull it, a su6r.C?quent ammnnlIca1 Jcaeh. 'This formation ill rulracLorv rnngtieves is altrlbuU?d Lo the prc.srnCV of aluauinum combined with c.ilicun jn addlt.lon In tnnl;neni~im in I.lic Lalerites, Iligb exII.Ictlon yields were oblalneJ when none or only a few I ,fraCLot' e, were InrmeJ. Hit s;intc rcfrarlnry cowl, Icxc5 also lend Lo surround Ow IaaIIiable meI.allle iron-IIIcI:el :iILoy CIUSisling ill the mau'ix, tIll: rrhv nreveu)Ling cuntacr ,Itlt LI5U Jeacl: solution; this, huwrvcr, ran ho ovu:rcoml by At ti itlon .111.11 retieCtiun. 'I'hc eIIcc l of prr.reJIctlun .,Ill itivi's vucli i's lye iii', ',udlum "Ill orIde, hv,Irogrn CIIInrILIC, etc., and Lht? 1111,Lre:InrLlI'll he'e:tleg un Lbe cxLt,icLitin are also iilsr.ussod 111 Lhe rcl,olt.]

Jan 1, 1979

By Jerry Bennett

This report describes the results of a survey of current blast area guarding procedures at surface and underground metal/nonmetal mines. It features five case histories (two surface and three underground mines) of blast guarding methods considered to represent the best systems in use in the U.S. Mining Industry. Elements of an effective blast guarding system are presented along with recommendations for improvements in current blast guarding practices. Industrial and military surveillance and detection technology was reviewed to determine if parallel technology exists for immediate application to blasting site security. While it is concluded that immediate transfer of industrial security technology will be limited, a number of recommendations are advanced for new research to adapt some of that technology for application to the mining environment. Two research areas considered to offer the most potential for improved blast guarding are presented. They are, computerized personnel tracking and blast area intrusion detection using infrared, microwave or E-field type detection systems.

Jan 1, 1981

By T. R. Achenbach

1. This, the final report to the U. S. Bureau of Mines on the program with the subject title, presents the data obtained from June 29, 1973, to April 20, 1974. 2. Operating in the Illinois #6 coal seam, the effectiveness of foam opposed to water was compared in reducing respirable coal dust. A combination of 39 foam generators and 14 water sprays were used during the foam tests. Sixty one water sprays were operated during the water tests. Data from 24 shifts using foam and 21 shifts using water are presented. 3. Additional work on foam generator design should be undertaken to provide coverage to a wider area with foam. 4. The general attitude of those working on the foam program and with the miner at the face was positive. It is urged that the work be continued. 5. The minor respiratory irritations evidently caused by an aerosol effect of the surfactant should be investigated. 6. The statistical analysis of the tests will be made and reported by the U. S. Bureau of Mines.

Jan 1, 1974

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to date and more nearly in line with present operating and safety practices in the industry. The rules are intended to supplement existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment, or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to data and more nearly in line with present operating and safety practices in the industry. The, rules are intended to supplement existing existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

By Piyush K. Dutta

This report describes the design, development, manufacture and incorporation of noise control features on a jumbo drill and the results of successful tests of this drill in surface and underground mines. The noise-reducing features developed under this program are applicable to future designs of jumbo mounted drills that can be cost effectively manufactured and have the potential to reduce noise levels at the operator's position from 115-120 dBA to 95 dBA or less without a reduction of currently attainable drilling rates.

Jan 1, 1985

By Edward A. Barrett, Kathleen M. Kowalski-Trakofler

This paper discusses the application of a training intervention that uses degraded images for improving the hazard recognition skills of miners. Method: NIOSH researchers, in an extensive literature review, identified fundamental psychological principles on perception that may be employed to enhance the ability of miners to recognize and respond to hazards in their dangerous work environment. Three studies were conducted to evaluate the effectiveness of the degraded image training intervention. A model of hazard recognition was developed to guide the study. Results: In the first study, miners from Pennsylvania, West Virginia and Alabama, who were taught with the aid of degraded images, scored significantly better on follow—up hazard recognition performance measures than those trained using traditional instructional methodologies. The second and third studies investigated the effectiveness of the training intervention at two mining companies. Data collected over a3—year period showed that lost—time injuries at mines in Alabama and Illinois declined soon after the training intervention was instituted. Impact on Industry: Further exploration of the hazard recognition model and the development of other interventions based on the model could support the validity of the steps in the hazard recognition model.

By R. D. Leitch

"INTRODUCTION The character of mine drainage from areas of low pyritic coal3 and from average pyritic coal4 has been investigated, and to complete the study it seemed desirable to select a number of mines situated in high pyritic are as to determine whether or not this variation determines the relative acidity of drainage from mines operating in these characteristic coal fields. Advantage has been taken of some worked on in 1918 by Henry Leighton 5, then Professor of Economic Geology, University of Pittsburgh. He visited and has reported certain areas of high pyritic coal which we also visited during this study. Many of the mines were found to be idle in 1930 and a few were caved shut, apparently for several years. However, samples of the outflow from all mines visited were collected if possible and analyzed, and some general information was gathered for each mine. The map (fig. 1) shows the location of these areas as given by Leighton.ACKNOWLEDGMENTSThe information and assistance obtained from officials and others at the mines visited during this study are gratefully acknowledged, as well as the original suggestion from Dr. Glenn V. Brown of the State Sanitary Water Board who called attention to the desirability of such a study.Thanks are also especially due the coal laboratory of the United States Bureau of Mines, under the direction of H. M. Cooper, for the analyses and determination of sulphur forms in the large number of solid samples necessary to the work reported,This study has been carried on under the direction of R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station, of the U. S. Bureau of Mines."

Jan 1, 1932

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

By Joseph S. Coffman

To determine the availability of manganese for metallurgical purposes from selected world resources, the Bureau of Mines evaluated the potential production of contained manganese in concentrates based on the demonstrated resources of 23 foreign and 8 domestic mines and deposits in 9 market economy countries. All but 2 of the 23 foreign deposits are operating mines; none of the domestic deposits are in operation. The demonstrated resources of the mines and deposits used in this study represent an in situ ore resource of approximately 2.2 billion tons," containing 780 million tons of manganese with a total recoverable production potential of 514 million tons of contained manganese in concentrates. The analyses of mines and deposits in this study indicate that about 213 million tons of the contained manganese (41 pct) is potentially available at a January 1981 constant dollar long-run total cost of up to $1.50 per long ton unit (22.4 lb, or 10.15 kg contained Mn), approximately 428 million tons (83 pet) is potentially available at a cost of about $1.75 or less, and 491 million tons (95 pet) is available at less than $3.30. The remaining 23 million tons, which is potentially available at much higher costs (about $8 to $35 per unit), represents the U.S. deposits. On an annual basis, with a cost range of up to $1.75 per long ton unit, the availability from currently operating mines would last at least 80 years based on 1980 world production data. Total manganese production costs are estimated to comprise mining-8 pet, beneficiation-3 pet, transportation-26 pet, and smelting-63 pet.

Jan 1, 1984

By J. Bennetts

As part of its mission to develop technology that will help increase the supply of critical and strategic minerals from domestic resources, the Bureau of Mines has investigated methods for beneficiating platinum-group metal ores from the Stillwater complex, Montana. This report presents the result of a bench-scale study employing froth flotation to recover a sulfide concentrate containing platinum-palladium values from a mineralized gabbro. Best results were obtained with a flotation scheme utilizing a mercaptobenzothiazone collector and sulfuric acid. Rougher concentrates containing approximately 11 oz Pt-Pd/ton and 90 pct of the metal values in the ore were obtained. Subsequently, cleaner concentrates containing approximately 26 oz Pt-Pd/ton and between 80 to 85 pct of the Pt-Pd values in the ore were prepared.

Jan 1, 1980

By Heithecker R. E.

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce,, published a report of the gas reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, may be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937