Search Documents

By Kermit G. Davis, Sean Gallagher, William S. Marras, Kimberly Kovacs

This study evaluated spinal loads associated with lifting and hanging heavy mining cable in a variety of postures. This electrical cable can weigh up to 10 kg per metre and is often lifted in restricted spaces in underground coal mines. Seven male subjects performed eight cable lifting and hanging tasks, while trunk kinematic data and trunk muscle electromyograms (EMGs) were obtained. The eight tasks were combinations of four postures (standing, stooping kneeling on one knee, or kneeling on both knees) and two levels of cable load (0 N or 100 N load added to the existing cable weight). An EMG-assisted model was used to calculate forces and moments acting on the lumbar spine. A two-way split-plot ANOVA showed that increased load (p<0.05) and changes in lifting posture (p<0.05) independently affected trunk muscle recruitment and spinal loading. The increase in cable load resulted in higher EMG activity of all trunk muscles and increased axial and lateral bending moments on the spine (p < 0.05). Changes in posture caused more selective adjustments in muscle recruitment and affected the sagittal plane moment (p < 0.05). Despite the more selective nature of trunk EMG changes due to posture, the magnitude of changes in spinal loading was often quite dramatic. However, average compression values exceeded 3400 N for all cable lifting tasks.

By Gordon T. Austin

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1986. Shipments of processed tripoli increased slightly in quantity and 20% in value. Production of garnet, a common iron- aluminum-silicate mineral, decreased 12% in quantity and value. There was a 4% increase in the quantity and an 11% increase in the value of refined garnet shipped when compared with 1985 shipments, a new record high. Production of crude special silica stone decreased 7% in quantity and slightly in value, and shipments of finished special silica stone products decreased slightly in quantity and increased 229% in value. Production of emery, an impure aluminum oxide, increased 77% in quantity and increased 269% in value of product mined and shipped. [ ]

Jan 1, 1988

By George A. Costello

A theoretical analysis is presented for the static and dynamic response of wire rope in deep-shaft mining operations. Expressions for the stresses in the individual wires of complex wire ropes are derived, and specific results for simple strands, 7x7 ropes, 6x 19 Seale ropes both with and without internal-wire-rope cores, and 6x25 filler-wire ropes both with and without internal-wire-rope cores, are presented for the case of ropes subjected to a combination of axial loading and bending over a sheave. Consideration is also given to the dynamic overloading associated with certain mining operations, such as dumping ore into a suspended skip and accelerating a fully loaded skip upward. Experiments to determine the axial stiffness of wire rope are described. Factors affecting the service life of wire rope, such as residual stresses, contact stresses, and fatigue behavior, are discussed. Specific research areas in need of further investigation are identified.

Jan 1, 1983

By M. H. Salsbury

This report describes the tunneling at the Leadville drainage tunnel, which was resumed in September 1950 with funds made available in the 1950 appropriation of the Department of the Interior. It brings up to date the account of the first project, carried on from December 1943 to August 1945, published by the Bureau of Mines which supervised both the first and second projects. In this report Leadville mining history, particularly related to drainage efforts, and the possibilities for future mine drainage are discussed briefly. An account of the second project, including a description of the operating cycle, exploratory drilling done as a safety measure, surveying procedures, geology, cost data, and other pertinent information, completes the report.

Jan 1, 1956

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

By E. C. Hoeman, W. C. Stoecker, R. C. Redfield

"INTRODUCTION Industrial sands, characterized by specific physical and chemical proportion, are,essential new materials for the manufacture of glass, sodium siliante and other products. Sands of suitable characteristics are used extensively for molds and cores in the casting of metals as a granular medium in municipal water filters, as abrasives, as traction sand to prevent the slipping of driving wheels of self-propelled vehicles on trucks and in various ceramic and other structural forms. In addition to the use of common silicon sands in concrete, cement, and mortar, special sands find use in sand-lime brick oxychloride cement, and flooring, for coating prepared roofing, and for placing ware in saggers although sand for sandpaper has been mostly displaced by other harder mineral or synthetic grains, other abrasive uses are numerous and include sandblasting stone sawing, glass burnishing and finishing."

Oct 1, 1945

By Manuel Gomez

Coking time was investigated as a function of coal properties, carbonization parameters, and the interactions between these variables. The results indicate that coal properties and carbonization conditions interact to influence the coking time, and these interactions may be determined quantitatively. Prediction equations were developed and used to simulate the effects of bulk density, flue temperature, and oven width on coking times for coals having a wide range of properties. The data presented provide additional information on the carbonization process to permit the coke oven operator to maintain closer control of coke production and coke uniformity.

Jan 1, 1968

By Ned Baker

Details are given of a fuel-induction system for a hydrogen, fueled engine. The induction system was designed to preclude backfire otherwise common in hydrogen fueled engines. System features and test data are presented and discussed in the context of the requirements peculiar to use in an underground mine environment. The fuel induction-system when tested in conjunction with a modified Caterpillar 3304 engine provided backfire free engine operation and satisfactory engine performance.

Jan 1, 1982

By Earl Redman

The Juneau Gold Belt portion of the Juneau Mining District has historically had the greatest mining and exploration activity within the district. Between 1880 and 1983, the mines within the Juneau Gold Belt produced 6.7 MM oz gold, 3.1 MM oz silver, and 45 MM lbs lead, which had a total value of about $157,000,000 at the time of production. This report summarizes Bureau of Mines work completed in 1986, the second year of the Juneau Mining District study. Fifty mines, prospects, and occurrences were examined and 638 samples were collected for analysis during 1986. Metallurgical samples were collected from seven deposits and preliminary tests of cyanide amenability have been completed for five of these. The simultaneous discovery by private industry and the Bureau of gold-bearing quartz veins cutting diorite gneiss recently exposed by the retreat of the Herbert Glacier is the most notable result of work during 1986. This location yielded gold values up to 7 oz/st.

Jan 1, 2011

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By M. R. Geer, H. F. Yancey

"INTRODUCTION Throughout the history of coal washing, the jig has been one of the most important coal-cleaning appliances. In 1935 34.7 percent of the 45,361,021 tons of clean coal produced was the product of jigging. 4/ Previous to 1928, most of the jigs used in the United States were of the piston type, with which sufficient mobility to allow stratification in bed is imparted by the reciprocating up-and-down movement of a piston in the water compartment adjacent to the screen compartment. In 1928, the Baum type of jig was introduces in this country and has since come into wide spread use. In this type, water pulsations are imparted by application and release of compressed air to the water compartment. All prior studies of the mechanism of seperating cleared coal from impurity by piston-type jigs. 5/ The same laws of settling, of course, apply to both types, piston or Baum, but the character of the separation with the Baum type may be modified more easily because of the flexibility with which air may be handled, as distinguished from the fixed action of eccentrics commonly used in piston jigs. Since no detailed studies are available to show the performance, that is, the character of the separation between coal and impurity, of the Baum type the Bureau of Mines undertook the investigation recorded in this report."

Jan 1, 1938

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

By Larry G. Stolarczyk

Jan 1, 1980

By Candice Stevens

The Territory of Afars and Issas is to receive its independence from France on June 27, 1977. The Territory&apos;s economic income was based on entrepôt trade through the port of Djibouti and trans-shipment of goods on the Chemin de Fer Franco-Ethiopian (CFE) railroad. The Territorial budget was scheduled to in- crease from $32.6 million3 in 1976 to $36 million in 1977, despite severe shortfalls in 1976 stemming from inflation and a persistent balance-of-trade deficit. Subsidies from France continued to sustain the economy, and the French pledged to provide approximately $140 million in aid annually after independence. In 1976, financial agreements were concluded with a number of Arab oil-producing countries, including Saudi Arabia which granted $10 million toward development projects. The new Republic of Djibouti is scheduled to become the 49th member State of the Organization of African Unity (OAU) and the 21st member of the Arab League, and to receive aid from their financial institutions. The port of Djibouti and the CFE railroad constituted the Territory&apos;s main economic resources. Traffic at the port greatly

Jan 1, 1980

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By M. P. Board, J. K. Whyatt, T. J. Williams

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mime in the Coeur d&apos;Alene Mining District of northern Idaho. In the present study, the energy release rate (ERR) index was used to evaluate three underhand stope backfill parameters--cement content, density, and placement gap-to determine their influence on rock bursts. This index provides a relative measure of the likelihood of rock bursting for a given rock mass. It is known that the elastic idealization of the rock mass inherent in this method causes underestimation of stope closure and hence underestimation of the influence of backfill on rock bursting. However, this evaluation still showed that (1) changing from present practice to one in which backfill was omitted altogether would increase the ERR by 42 pct and (2) perfect placement of backfill would reduce the ERR below present practice levels by 28 pct. The easiest step toward perfect placement would be elimination of the placement gap, which accounted for half of the difference in ERR between present practice and ideal placement conditions. There was no indication that increasing initial fill strength through increased cement content would affect the ERR.

Jan 1, 1992

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars for the purpose of disseminating recent advances in mining technology related to coal mine fire and explosion prevention. Primary, although not exclusive, emphasis is placed on underground coal mining. The papers address research accomplishments ranging from methods for detecting mine fires to remote sealing systems for extinguishing coal mine fires. Each paper represents the current state-of-the-art in the respective research categories. Presentations include research occurring from both Bureau in-house and contract efforts.

Jan 1, 1978

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine&apos;s heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By Burton Scott

A device for detecting carbon monoxide at ppm levels is described which is based on the measurement of infrared absorption at 4.65 microns. The unique feature of the nondispersive infrared instrument is contained in the optical design which includes a confocal cavity, increasing the effective optical path length by a large factor, thus greatly reducing the required package size. The cavity has the effect of reducing the total amount of radiation passing to the detector, but at the same time increasing the percent attenuation observed when adding CO, by a factor called gain. The radiation is chopped by a filter wheel which contains narrow band filters at 4.0 and 4.65 microns. The resultant signal produced by the pyroelectric detector is demodulated by the electronics to product an automatic gain control signal, proportional to the total radiation, and a difference signal, proportional to the CO present. Tests of a breadboard model are described which show cavity gains of 10 with noise levels equivalent to 2 to 10 ppm CO.

Jan 1, 1975

By James R. Boyle

The Bureau of Mines initiated a program to address short-and long-term objectives of wetlands restoration as a option for reclamation of lands mined for phosphate. The short-term objectives were to identify a suitable wetland test site, initiate an extensive premining monitoring plan, develop an acceptable mining plan, and recontour and revegetate the test site. These goals were accomplished using a unique combination of expertise provided by Federal and State agencies and private industry. A 6.5-ha forested wetland with an associated streambed was offered by private industry as the test site. A premining monitoring program was established and carried out from May 1982 to October 1983. A control site was established to determine ecological changes unrelated to mining. Clearing and mining began in October 1983 and was completed in April 1984. Grading and streambed restoration was completed in February 1986. Revegetation of the site was completed in February 1987. The program to meet the long-term objective of postmining monitoring is described.

Jan 1, 1988