Search Documents

By J. R. Cobble

As part of the Federal Bureau of Mines project to develop new or improved materials for metallurgical furnace applications, the Tuscaloosa (Ala.) Research Center has conducted research to develop a reproducible laboratory test for evaluating the resistance of refractories to molten slags. Tests were conducted with a slag representative of slag used to produce mineral wool. A rotating cylindrical furnace was lined with the brick being tested, and it was operated at temperatures up to 1,660° C for periods ranging from 8 to 32 hours. The effects of such variables as slag temperature, rotational velocity, charge rate, and contact time on refractory erosion were determined. The research demonstrated the reproducibility of the test procedure developed.

Jan 1, 1980

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) In-shaft equipment design and specification criteria are considered as they influence guideline preparation. (b) A comprehensive review of hoist electric drives and controls as applied to mine hoists is set forth with special reference to duty cycle calculations and their effect on electrical component selection.

Jan 1, 1988

By Thomas A. Phillips

The Bureau of Mines presents an economic evaluation of its leach- electrolysis process for recovering lead from galena concentrate. In this process, galena concentrate is leached at 200° F with a ferric chloride-brine solution to extract lead while leaving sulfur in the residue, which is discarded. The solution after leaching is concentrated and cooled to 100° F by vacuum evaporation to crystallize lead chloride from which metallic lead and chlorine are produced by fused-salt electrolysis. Chlorine is used to regenerate the spent leach solution before it is recycled. A cost estimate was prepared for a plant capable of producing 300 tons per day of lead, 330 days per year. The fixed capital cost on a third-quarter 1977 basis Fs $27,500,000, and the estimated operating cost without a charge for the concentrate is 4.9 cents per pound of lead product. Assuming a selling price for corroding-grade lead of 31 cents per pound and a charge for the concentrate of $332 per ton, the interest rate of return on investment after taxes is 16 percent. The leach-electrolysis process, therefore, appears to be economically attractive under the assumed market conditions.

Jan 1, 1978

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

By R. C. Ellman

Since successful industrial lignite-burning equipment was developed in 1925, the commercial use of lignite as a fuel for power plants has increased. It has proved an entirely satisfactory fuel for generating power and can be burned efficiently by various methods.4/ Equipment to fire pulverized lignite was installed and used successfully at the Trinidad Station of the Texas Power & Light Co. as early as 1926. The lignite was predried in steam-heated grid driers before pulverizing.5/ This method of firing was used later in the Comal Station of the San Antonio Public Service Commission.6/ Both stations, however, have since been converted to use other fuels. Units for pulverizing and drying lignite are relatively new in the lignite-consuming region of North Dakota. The air which sweeps the pulverizer and transports the pulverized product to the burners is preheated to dry the lignite during pulverization. The first unit was installed in 1948 in one of the two boiler units of the Crookston Station, Otter Tail Power Co., Crookston, Minn.7/ In 1951 the 30,000-kw. W. J. Neal Station, Central Power Electric Cooperative, Inc., Voltaire, N. Oak., was designed and constructed for firing pulverized lignite exclusively. It is the largest lignite-fired, power-generating station in North Dakota. The 44,000-kw. Lewis and Clark Station of the Montana-Dakota Utilities Co., Sidney, Mont., is fired by a similar pulverizing system. Operation of this plant was begun in October 1958. At Fergus Falls, Minn., the 53,500-kw. Hoot Lake Station of the Otter Tail Power Co., also using a pulverized lignite-firing system, began operating in September 1959.

Jan 1, 1961

By R. D. Joseph

This report deals exclusively with roof-fall accidents that occurred during 1955 and 1956 in both anthracite and bituminous-coal mines throughout the United States. The report stems from a cooperative study conducted by the Bureau of Mines and the Roof-Control Committee of the Coal-Mining Section, National Safety Council. The study includes an analysis of individual accident reports, sets forth the measurable factors, and compares such factors with a representative sample of average data from 39 anthracite mines and 117 bituminous mines (appendixes A and B). Particular emphasis is placed on fatal roof-fall accidents with respect to their causes, locations, and the methods of support used at the point of occurrence. INTRODUCTION The purpose of the report is to classify all measurable details of the occurrences of roof-fall fatalities so that the material presented will assist those promoting safety and will serve as a manual for those whose principal duty is inspection of mines.

Jan 1, 1958

By Paul S. Goodman

Volume I This report presents the first national survey of miners' attitudes and opinions about their-work. The goal is to present attitudinal data that bears on coal production. Interviews were conducted in 26 mines with 2,000 miners. High levels of cooperation were exhibited by management, union and the employees. Data are presented about miners' attitudes about general aspects of their work such as pay, supervision, their jobs, etc. Another section of this report reviews opinions about specific aspects of work performance. Recommendations are presented.

Jan 1, 1985

By Russel R. Bohn

The objectives of this study were to: (a) determine the state of the art for the control effectiveness of various chemical dust suppressants, (b) field test the effectiveness of the dust suppressants, and (c) develop technical guidelines for selecting and implementing cost effective tailings pond dust control programs. Chemical stabilizers evaluated under field conditions were: Coherax, Calcium Lignosulfonate, Nalco 656, 655, and Magnesium Chloride. Testing in the field utilized a portable field in-situ wind tunnel. The wind tunnel was placed on the tailings surface and simulated wind speeds of up to 80 mph were used to determine wind erosion threshold velocities. Emission rate testing was performed with the wind tunnel through the use of a real-time cascade impactor. A control cost effectiveness evaluation was performed to determine how efficient the chemical stabilizers were on a dollars expended per acre basis.

Jan 1, 1983

By J. Dean Warner

From 1984 through 1987, the Bureau of Mines investigated numerous prospects and new discoveries of columbium, rare-earth elements (REE), uranium, zirconium, and other metals associated with the multi-phased peralkaline granite at Bokan Mountain, southeastern Alaska. This report summarizes the mineral evaluations and estimates indicated and inferred resources for those prospects containing significant tonnage and grade. A total of approximately 96.2 MM lb Cb205 (43 pct of the tonnage at a grade exceeding 0.125 pct Cb205), and 11.8 MM lb U308, 27.9 MM lb Th02, 133.0 MM lb Y203, 637.6 MM lb ZrO2, and 241 MM lb REO are estimated to be contained within nine deposits totalling 37.8 million tons (at least 80 pct of resource tonnage also exceeds 0.5 pct Y203 + REO). Generally, half of the REO content is composed of the heavy yttrium subgroup. Several deposits also contain beryllium and tantalum; 2.1 MM lb of Ta205 and 8.9 MM lbs of BeO were estimated. These estimates would likely be substantially increased with additional exploration. Four deposit types were investigated; shear zones and fracture-related deposits, pegmatites, mineralized dikes, and placers. Mineralized dikes contain most of the beryllium, columbium, tantalum, yttrium, zirconium, and REE resources, whereas shear zones and fracture-related deposits (Ross-Adams mine) contain the principal of the uranium resource. Pegmatites are similarly mineralized as are dike deposits, and contain low levels of gold. Placer potential is suggested, but no deposits were found.

Jan 1, 2011

By Robert A. Harrow

This report documents the results of the development and installation of an illumination system for an underground coal mine Shortwall Mining Section. Also presented are the techniques used for the above ground test and evaluation of the lighting system prior to installation underground which resulted in the issuance of a Statement of Test and Evaluation (STE) from the Mine Safety and Health Administration, Technical Support, Beckley, West Virginia.

Jan 1, 1979

By Philip K. Hopke

A systematic study of the mechanism of interaction of 218Po(RaA) armed by the decay of 222Rn with airborne particulate matter has been made. The rate of attachment of RaA to particles in the diameter range of 0.1 µm to 10.0 µm has been measured as a function of particle size, concentration, and composition, radon concentration, time of interaction, relative humidity and temperature. It was found that under the conditions in these experiments the attachment rate was proportional to the square of the particle diameter and varied with temperature and relative humidity. The composition of the particles apparently has no effect on the attachment. The variation in attachment rate was related to a sticking probability coefficient of approximately 0.02 that varies systematically with temperature and humidity. In addition, the rate of deposition of RaA on the wall of the attachment kinetics system was measured and also found to change with temperature and relative humidity.

Jan 1, 1980

By S. H. Lorain

Mechanized dirt-moving equipment has greatly increased the scope of prospect trenching by lowering the costs and increasing the speed of such work. Where the soil covering was more than 3 or 4 feet deep, operators were quickly discouraged and abandoned surface exploration in favor of shaft sinking, drifting, or diamond drilling; wildcat trenching was seldom undertaken, even where the soil covering was thin. Although power shovels, trench diggers, and draglines are useful under special conditions, caterpillar-mounted angledozers will usually do the same type of work and have a far wider range of adaptability. They are therefore incomparably the most generally useful equipment for the purpose. Since 199 the Bureau of Mines has been engaged in a widespread search for minerals useful to the war program; this work required a great deal of pioneer exploration in areas where known outcrops were marginal or subcommercial by pre-war standards. Engineers in charge of field operations were quick to perceive the applicability of mechanized trenching on a fairly large scale, particularly in the Northwestern States, where completely exposed vein-outcrops are rare. Probably no other organization to date has done a comparable amount of angledozer prospect trenching under such a wide range of conditions. The following comments and accompanying cost tables are based on work performed chiefly in Idaho, under a variety of physical and climatic conditions. The most important applications of the angledozer for such work may be described under three heads:

Jan 1, 1944

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By Joe Maher

[ ]

Jan 1, 1976

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965