Search Documents

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

By Wilbur I. Duvall

This report presents experimental data on crater formation in four rock types. From an analysis of these data a general theory of rock breakage by explosives is deduced. This theory accounts for most of the rock breakage and other phenomena that occur when a concentrated charge is detonated in a drill hole near a free surface. From instrumented crater tests and high-speed motion pictures of the explosions, various experimental checks on the deduced theory of rock breakage are made. The general mechanism of rock breakage by explosives as described in this report is outlined briefly below. The detonation of the explosive charge creates a high gas pressure in the charge hole, which in turn generates a compressive strain pulse in the surrounding rock. This compressive strain pulse travels outward in all directions from the charge hole. Near the charge hole the amplitude of this strain pulse is sufficient to cause crushing of the rock. However, as the strain pulse travels outward its amplitude decays rapidly until no further crushing of the rock is possible. The compressive strain pulse continues to travel outward until it is reflected by a free surface. Upon reflection the compressive strain pulse becomes a tensile strain pulse. As the strength of rock in tension is much less than in compression, the reflected tensile strain pulse is able to break the rock in tension, progressing from the free surface back toward the shot point. In other words, the rock is pulled apart, not pushed apart.

Jan 1, 1957

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

By Sheridan J. Rodgers

The quantity and behavior of gases in metal and nonmetal mines were monitored to provide background information on feasibility of incipient fire detection systems. Monitoring was conducted during working and nonworking periods at intake air, return air and working places. Gases generated during diesel operations and shot firing were of particular interest. Gases which were monitored were CU, C02, N0, N02 and S02: submicron particulate concentrations were monitored also. Commercially available instruments were used and included nondispersive infrared, electrochemical and chemiluminescent types. The ratios of the various gases generated during diesel operations and shot firing were similar to those expected from an incipient fire, with the exception of the C02/NOx ratio, which is sufficiently different to be considered for early fire warning. Samples taken near leaking bulkheads showed high C02 levels and low C0 levels, the reverse of anticipated behavior in coal mines.

Jan 1, 1976

By P. B. Altringer

The Federal Bureau of Mines conducted a study to determine if residues from fractional distillation represent a potential source of mineral values. A literature review and discussions with tar sand specialists failed to disclose the mineralogical nature of residues remaining after bitumen extraction. To develop this information, pilot plant tar sand residues or toluene-cleaned tar sands from 23 deposits were examined. The nature of the residues was determined by standard mineralogical methods and the chemical compositions were determined by X-ray and ICP (inductively-coupled plasma spectroscopy). None of the sands or concentrates examined contained sufficient valuable minerals to be economically important.

Jan 1, 1982

By Gary R. Peterson

In order to determine the potential availability of alumina to feed U.S. aluminum smellers, the Bureau of Mines evaluated 39 domestic mines and deposits of bauxite, alunite, and high-alumina clays and found that substantial increases in alumina prices would be necessary before nonbauxitic deposits could become competitive with bauxite. As part of the study, a price-tonnage relationship was developed indicating the quantity of alumina that could be produced from known deposits at various alumina prices and at a 15-pct discounted cash flow rate of return on the required capital investment. All capital and operating costs were calculated in August 1980 dollars. The domestic bauxite reserve base comprises three operating bauxite mines in Arkansas containing some 15.6 million metric tons of recoverable alumina (A1203). Ferruginous bauxites, clays, and alunites fall into the subeconomic category of identified aluminum resources, which, at the demonstrated level, contain over 4,000 million metric tons of alumina that are estimated to be recoverable. Analyses indicate that, at the demonstrated resource level, a total of some 15.6 million metric tons of alumina, all from three active Arkansas bauxite mines, is recoverable at a 1980 price of $0.12 per pound ($264 per metric ton) of alumina. A price of approximately $0.26 per pound ($573 per metric ton) of alumina would be required for production of the total U.S. resource. Thus, unless new technological breakthroughs occur that could make alternate sources of alumina competitive with bauxite, U.S. dependence upon imported bauxite will continue to increase.

Jan 1, 1981

By R. H. Hiltz

The Coal Mine Health and Safety Act of 1969 legislated maximum dust levels for the working place. As the law was implemented, extensive efforts were undertaken to provide the technology necessary to control dust generation. One approach to dust control was the use of high expansion foam in place of the usual water sprays on coal cutting equipment. At the time of the act, high expansion foam had already seen considerable testing for the suppression of dust in underground coal mines. Work by MSA, several coal companies and the Bureau of Mines itself had provided data which showed foam to have some merit as a dust control mechanism. It suffered in a few areas, however, which limited its practical application. Its principal difficulty was persistence which hampered operations due to foam buildup, but problems were also encountered due to equipment size and form.

Jan 1, 1975

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By E. O. RHODES

Germany's' wartime coal-tar industry had two main branches, which can best be considered individually because their raw materials, operations, and distributions were almost completely separated. One branch, old and well-established, was concerned almost entirely with processing coal tar produced by the high-temperature carbonization of caking bituminous coal. Carbonization was effected principally in byproduct- coke ovens and to less extent in vertical, horizontal, and inclined retorts. The high-temperature tar was all processed in tar-distilling plants that handled high-temperature tar almost exclusively.

Sep 1, 1947

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By Dong G. Chae

A model for the leaching of oxide ores is developed and II correlated with laboratory tests for percolation leaching of copper oxide are. Using the model, recovery of metal values and lixiviant concentration of the effluent solution at any time may be evaluated. For the copper oxide ore a simplified version of the model is examined for the leaching mechanism consisting of: 1) a surface flush reaction with the highest rate of lixiviant consumption; 2) penetration of lixiviant to react with copper minerals and gangue constituents; and, 3) slow lixiviant consumption, mostly by residual gangue materials. The simplified model is able to explain reasonably the leaching behavior of copper oxide ore by introducing a concept of effective initial size to correct for packing in a bed of fine particles.

Jan 1, 1979

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. nonmetallic mining workforce from March through September 1986. Similar reports have been prepared for the metallic, stone, and sand and gravel mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the cool mining sector.

Jan 1, 1988

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

The principal activities of the Bureau of Mines Explosives Research Center during fiscal year 1969 (July 1: 1968, to June 30, 1969) are reviewed in part 1. Part 2 presents short abstracts of the publications issued during this period in the Bureau series and in the outside press. These publications are referenced in part 1 by underlined numbers in parentheses. Other publications, which are not abstracted, are cited in footnotes throughout the paper. ACKNOWLEDGEMENTS The Bureau acknowledges the support received through cooperative agreement in fiscal year 1969 from the Manufacturing Chemists Association. It also acknowledges the sponsorship by the following Government agencies of research conducted during that period: Department of the Air Force, Department of the Army, Department of Health, Education, and Welfare, Department of the Navy, Federal Aviation Administration, National Aeronautics and Space Administration, Space Nuclear Propulsion Office, and United States Coast Guard.

Jan 1, 1970

By Ellis S. Hertzog

The relatively large amount of phosphorous occurring in many iron ores limits their usefulness aid sometimes renders them valueless under present conditions of nip-iron manufacture. A practical method for removing the phosphorus would be valuable to the iron and steel industry. Gravity concentration has been of little value as far as the removal of phosphorous is concerned, because the compounds of this element are, as a rule, disseminated very finely. Removal of the phosphorous by leaching is not a new idea and has been the subject of some investigation,3,4/ out for data :lave been published. W.R. Crane published analyse of various ore bodies in the Birmingham ham district. The hard or unleached ores a .re much higher in phosphorous than the Soft, leached ores along the outcrops. This fact indicates that as mild a leaching agent as water removes phosphorus effectively if enough time is allowed for it to react. As the forms in which phosphorous occurs in the iron ores are important in the consideration of any leaching operation, much time was expended in devising a method for determining them. According to Professor McVey, University of Alabama, the phosphorous-bearing minerals in the red iron ores of Alabama have not been positively identified by any microscopic methods.

Jan 1, 1935

By Frederick C. Trutt

This report is intended as a reference for personnel interested in the computer anlaysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures described include the Newton-Raphson iterative technique for the analysis of normal operation as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults. During program development, strict attention has been given to the inclusion of core and/or time saving techniques such that these algorithms may be implemented on small as well as large computers. Program languages include FORTRAN IV for batch processing applications and APL or BASIC for interactive applications.

Jan 1, 1981

By Virgil A. Marple

It was the purpose of this contract to conduct research in several different areas of instrumentation used to determine the quantity of respirable dust in the mining atmosphere. One area of research was in evaluation of instruments including several respirable dust monitors, several types of photometers, and a QCM cascade impactor. An instrument evaluation chamber was developed to aid in evaluating the instruments in a dust atmosphere. Another area of research was investigations into new instrumentation concepts, such as a virtual impactor/photometer instrument, a new optical device which can be used as either an optical particle counter or photometer, a new personal respirable sampler, which employs an impactor instead of a cyclone as a preclassifier, and the development of a new cascade impactor, which deposits the particles uniformly on the impaction plate. Another area of research included the use of many of these instruments in two field studies, including a silica sand plant and a tungsten mine.

Jan 1, 1981

By D. T. Holmes, W. G. Sandell

"INTRODUCTION Three representative lots of ore wore obtained from the Aguila minim district in Arizona during the Bureau's exploration of manganese deposits there. Since only selectively mined ore from this district will meet commercial-grade specifications, the ores were studied to determine their amenability to concentration.Although the purpose of the investigation was to determine the possibilities of the district as a source of commercial-grade manganese, testing was sufficiently comprehensive to indicate the response of the ores to several different types of treatment. Many data of secondary importance have been omitted, end only the more pertinent tests are presented in detail.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to. Metals Reserve Company was ferro-grade manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., O.18 percent; Al12O3, max., 6 percent; Zn, max., 1 percent.Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.O percent iron, and. 11 percent silica plus alumina. Premiums were paid for manganese con¬tent over 48 percent and iron content under 6 percent, penalties being imposed upon products containing loss than 48 percent manganese or more than 6 percent iron or more than U. percent. silica plus alumina.. The specifications for commercial manganese further required that the maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined.."

Aug 1, 1948

By I. Liebman

The Bureau of Mines conducted research to develop triggered barrier systems for protection against gas explosions that can occur in underground coal mines during the use of continuous miners. Several extinguishing agents were tested in barriers at a simulated mine face. Water, powered by pressurized nitrogen, was found to be efficient in stopping fully developed gas explosions, but it had little effect against the explosion during its incipient stage. Hybrid combinations of currently known extinguishants, however, were successful against incipient explosions. Three hybrids that were developed and tested consisted of Halon 1301, combined with either an aqueous foam solution, water, or a dry chemical powder. The three hybrids were found to be more efficient than any constituent alone. Results of the tests point to a synergism between the hybrid components, and indicate that the Halon aids in dispersing its constituent and also converts the aqueous foam solution into a stable fine foam and the water into fine drops.

Jan 1, 1978

By T. J. Driscoll

Methane-air mixtures can ignite as a result of sparking or rubbing of materials, particularly by impact involving light alloys and rusted steel where an exothermic thermite reaction can occur. This report reviews the published literature and describes a new method utilized by the Bureau of Mines for studying the processes occurring during collisions of light metals with rusted steels. The method involves measuring the spectra of sparks and explosions in methane-air mixtures using a photodiode array. Initial results obtained using magnesium and aluminum alloy 6061-T651 projectiles striking rusted steel are reported. These results indicate that the continuous parts of the spectra show a larger intensity for incendive sparks compared with nonincendive sparks, with the largest relative change in the higher energy, ultraviolet region. An unexpected shift of the intensity maximum for the continuous parts of the spectra towards the infrared region was observed for the more incendive sparks. Evaluation of rusted steel samples with electron microscopy, energy-dispersive X-ray spectrography, and Auger electron spectroscopy after they had been impacted by aluminum alloys indicated that aluminum was transferred to the steel in the form of islands that became larger as a function of increasing projectile velocity.

Jan 1, 1982