Search Documents

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By Gary E. Sherman

This report presents a Bureau of Mines study on the cost of mine permitting and compliance with environmental regulations in Alaska. It discusses permitting requirements and procedures for placer and lode mines. Placer miners must comply with recently established (1988) water quality regulations and effluent treatment requirements. To estimate the impact differing treatment options (no recycle, 100% recycling, and flocculation) have on a placer mine's rate of return, three models (1,500, 1,000, and 500 yd3/d) were simulated. Rates of return for these models show a marked decrease as effluent treatment is increased. The incremental increase in operating cost from one treatment option to the next is relatively small; however the opportunity cost of lost production if' significant and accounts for the decreasing rate of return with increased effluent treatment. Lode mines face greater costs for permitting and compliance than similarly sized placer mines as a result of the impact of the operation. Direct permitting costs for lode mines range from 2 to 6% of total project cost, with 4% the most common figure cited by industry. Total costs for permitting and compliance are approximately double those for permitting. Indirect costs associated with compliance include mitigation, monitoring, and reclamation.

Jan 1, 1991

These proceedings consist of papers presented at Bureau of Mines Technology Transfer Seminars in December 1983 for the purpose of disseminating recent advances in mining technology in the area of mine ground control. The Bureau of Mines conducts several of these seminars each year in order to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.

Jan 1, 1984

By T. F. Mitchell, B. K. Shibler, J. V. Batty, W. G. Sandell, G. M. Potter

"INTRODUCTION The Park City district, situated 30 miles east of Salt Lake City, Utah, in the Wasatch Mountains, Is a well-known producer of lead, zinc, and precious metals. Nearly continuous production has been maintained from the dis¬trict since its early discovery about 1870. For approximately 50 years, gravity milling methods were employed to beneficiate Park City ore, and during that time tailings from the mills were sluiced down Silver Creek and deposited on lands below the camp for 7 miles.Owing to the large tonnage of tailings deposited along Silver Creek, considerable work was done in the past in the attempt to develop a low-cost concentration method for re-treating this material, but no-method was found that was economically feasible. The Bureau of Mines was asked to conduct beneficiation tests on Park City tailings in November 1944, and metallurgical studies were initiated at that time. This report summarizes the results of laboratory ore-dressing studies made on samples from the Grasselli deposit."

Dec 1, 1947

By Lloyd A. Morley

This eight-chapter document is the second volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. Building upon Volume I, the subject of protective equipment and relaying starts Volume II, first as an introduction in Chapter 8, then by a treatment of device selection in Chapter 9. Chapter 10 continues system protection in terms of transients and overvoltages. Chapter 11 describes the design of major power equipment, including power centers, switchhouses, and substations. Solid-state applications in mining are given in Chapter 12, and batteries and battery charging are discussed in Chapter 13. Chapter 14 covers electrical-equipment in hazardous locations of mining operations. The report concludes with Chapter 15, a discussion of electrical maintenance as well as some specific mine electrical problems. Information on surface and underground use is included in all these chapters. An index finishes the documentation and is cross-referenced to both report volumes.

Jan 1, 1982

By Richard Mainiero, Donald A. Hurd, James H. Rowland

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation. A major goal of the research was to gain a better understanding of the factors that lead to the generation of toxic fumes in blasting operations. Earlier studies have suggested that the high nitrogen dioxide and nitric oxide concentrations in product clouds might be the result of the poor confinement provided by relatively weak ground strata or the exposure of the explosive to ground water prior to shooting the shot. Various mixtures of ANFO and emulsion were detonated in schedule 80 steel pipe and galvanized sheet metal pipe to evaluate the effect of confinement. Explosive mixtures were also allowed to soak in water for less than one day, one week, one month, and two months to determine which explosive mixtures would be degraded and observe what effect this degradation had on fume production. Results indicated that the production of nitrogen dioxide increased with low confinement of the detonating explosive and with exposure of the explosive to water.

This Bureau of Mines report is devoted to descriptions of investigations pertaining to underground mine trailing cables, their handling, splicing, and the use of couplers.

Jan 1, 1979

By Charles L. Parsons

Early in 1912, from information received by the Bureau of Mines, it became evident that quantities of valuable radium-bearing ore from Colorado were being exported for manufacture in foreign countries and that at least part of the manufactured product was being returned to this country and sold at a price entirely incommensurate with that received by the miner and the prospector. Consequently, in line with its efforts to increase efficiency in the mining and treatment of mineral resources, the Bureau of Mines undertook an investigation of conditions. Results of this preliminary investigation were published, in the summer of 1913, as Bulletin 70,a which gave an outline of the radium deposits of the West, the conditions of mining, the wastes involved, and the status of the production of radium from its ores. At about this time newspapers and medical journals were publishing statements regarding the value of radium in cancer therapy. These reports, although many of them were exaggerated, brought out clearly the remarkable virtue of the gamma rays for the treatment of cancer and other malignant growths. In view of the fact that the largest known supplies of radium ore in the world are in the States of Colorado and Utah and on the public lands of the United States, it was deemed highly important for the Bureau of Mines to study the production of radium in detail. Such study, it was hoped, would enable the prospector and miner to obtain a fairer price for the ores and would furnish information necessary in case Congress appropriated funds to develop methods for extracting radium from ore on the public lands under Government supervision, to be supplied at cost to the hospitals of the Army, Navy, and Public Health Service.

Jan 1, 1915

By Harry R. Nicholls

The objectives of this investigation were to determine the strain propagation laws for a strain pulse in salt and to compare the seismic effects from the detonation of different explosives in salt. The investigation showed that a strain propagation law of the type, e = K(R/W 1/3 ) n, and a strain energy propagation law of the type, Ea/W 1/3 = K(R/WI/3)b , are valid in salt. A change in the regression law coefficient, n , was noted with strain level. A similar change in b was inferred because strain energy is proportional to the square of strain amplitude. Particle velocity data may be used interchangeably with strain data under the test conditions.

Jan 1, 1962

By Thomas Novak, Jeffrey L. Kohler, Joseph Sottile, Steve J. Gnapragasam

Modern underground coal mines can be very large, having a total connected load in excess of l5 000 hp. These mines generally have many miles of high-power conveyor belts and 15 or more miles of high-voltage power cables at distribution voltages of 12.47, 13.2, 13.8, or 14.4 kV. The shielded cables used in mine power distribution systems have a significant level of capacitance, on the order of 110 pF/ft. This level of capacitance, in an extensive power distribution system at today's voltage levels, can cause significant charging currents during a ground fault. This paper addresses the potential detrimental effects of capacitance charging currents during line-to-ground faults in mine power distribution systems. A representative mine power system is modeled, and simulations with faults at various locations are conducted to evaluate the effects of this capacitance on the level of fault current and relay selectivity. This paper also includes results of capacitance measurements made on mine power feeder cables used to validate the simulation model.

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By S. M. Shelton

Tests employing various ore-dressing methods were made on a manganese wad ore from the W. A. Chinn property in the Batesville-Cushman district of Arkansas in an effort to develop a practicable procedure for the production of ferromanganese-grade concentrates. The ore body occurs as a bed approximately 7 feet thick in the residual clay of the Ferndale limestone formation5/. The crude wad ores are soft aggregates of various oxides of manganese, which are loosely bonded together. Hard lumps of high-grade ore are disseminated throughout the wad. Hausmannite, pyrolusite, and psilomelane are the principal minerals. Some clay is present, but most of the gangue consists of leached fragments of the original siliceous and calcareous rocks in which the manganese occurred. In addition, hydrated oxides of iron, which axe present, also must be considered as gangue. Definite phosphate minerals have not been identified.

Jan 1, 1942

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 22 jurisdictions of the Near East and South Asia. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes : First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1972

By V. F. Swanson

As part of the Bureau of Mines titanium resources examination program, samples of altered rock (saprolite) and unaltered rock from the Roseland anorthosite near Roseland, Nelson County, Va., were tested for amenability to beneficiation by flotation. A flotation technique was developed to produce bulk concentrates of ilmenite, rutile, sphene, and leucoxene. It was necessary to first float apatite using oleic acid as the collector, in an alkaline pulp with dextrine as a titanium mineral depressant. The titanium minerals could then be floated from the apatite tailing, using fluosilicic acid to depress the remaining apatite, morin to depress ferromagnesian minerals (when present), and oleic acid as the collector. A bulk titanium mineral concentrate, analyzing 66.0 percent Ti02 and 0.08 percent P205, was obtained from a sample of the unaltered rock which contained 5.45 percent TiO2 and 2.81 percent P205. Overall recovery in the concentrate was 47.1 percent of the total TiO2 in the ore. About 55 to 65 percent of the saprolite sample was clay and was removed by attrition scrubbing and decantation. The apatite prefloat procedure was applied to the saprolite sands; subsequent titanium mine: 1 flotation recovered 72.2 percent of the Ti02 in a bulk concentrate containing 65.1 percent TiO2 and 0.20 percent P205.

Jan 1, 1962

By D. O. Kennedy

"INTRODUCTION During the recent war attention was directed to prevent the destruction of American industries by sabotage. By Executive order of Lay 19, 1942, the Bureau of Mines was required to conduct investigations and make recommendations that would prevent loss of production of essential war minerals. The Health and Safety Branch of the Bureau of Lines was able to extend its activities with minimum loss of time to include security surveys of the important mineral facilities in the United States.A Mineral Production Security Division was established in the Health and Safety Branch with funds appropriated for that purpose by Congress in April 1942. From July 1942 to July 1945 engineers of this division, under the direction of D. Harrington, Chief, Health and Safety Branch, and J. J. Forbes, Chief, Mineral Production and Security Division, conducted investigations of 1,560 metallic and nonmetallic mines and associated facilities in accordance with the requirements of the Executive order.PURPOSEAn analysis of losses in the production of minerals shows that failure or destruction of equipment either from deliberate or accidental causes produces essentially the same result. Maximum production is insured by the prevention of subversive activities, fires, and industrial accidents."

Sep 1, 1946

By R. E. Zane

The Northwest Experiment Station of the Bureau of :,!in-s, in cooperation with the College of Mines, University of Washington, has completed a detailed investigation-of the physical and chemical properties of western cokes made or used in the Pacific Northwest, as evaluated by standard methods./ One of the properties determined, to which more or less importance has been attached, was reactivity5/ or combustibility. As no standardized procedure is available, it was necessary to develop a workable method for evaluating this property. The combustibility of coke is usually measured by the formation of carbon dioxide with time at a particular temperature or by the reduction of carbon dioxide to carbon monoxide. Analysis of the resulting gases commonly is required to evaluate the result. The method described in this paper is simple and direct in that the sample of coke or other carbonaceous material is weighed as it burns; the loss in weight and time is indicated by a balance and clock arrangement. Gas analyses are not required. Methods similar in principle have been used by Tu, Davis, and Hottel6/ and by Oshima and Fukuda7/ for determining the combustion rate of carbon and for studying the effect of ash on combustion characteristics. Both methods are more elaborate in procedure and apparatus required than that described here. Briefly, the method comprises burning a sample of coarsely grained coke or

Jan 1, 1940

By D. L. Pitt

This paper, describing the milling methods at the concentrator of the Premier Gold Mining Co., Ltd., Premier, B. C., Canada, is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States and Canada. ACKNOWLEDGMENTS The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by the engineering staff and accounting department of the Premier Gold Mining Co., Ltd., all of whom have assisted materially in gathering the data used.

Jan 1, 1933

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag composition. Liquidus and solidus temperatures and solid solubilities were determined for the BaF2-Y203 system, and the information is presented as the phase diagram. The phase diagram was constructed from data obtained by ceramography, X-ray diffraction, and thermal analysis of specimens encapsulated in small molybdenum ampoules. The data indicate a simple eutectic system with maximum terminal solid solubilities of less than 1 mole pct. The eutectic temperature is 1,343° C, and the composition of the eutectic is less than 1 mole pct Y203.

Jan 1, 1970

By Frank A. Peters

An evaluation is made of a lime-soda sinter process for extracting alumina from clay. In this process, alumina is extracted by sintering clay with soda ash and limestone and then leaching the sinter with a dilute sodium carbonate solution. The sodium aluminate solution formed during leaching is separated from the residue and treated with lime in autoclaves to remove dissolved silica before alumina trihydrate is precipitated with carbon dioxide. The tri-hydrate is then calcined to a-alumina. Two options, dry grinding and wet grinding, are used in the sintering step. The fixed capital costs for plants producing 1,000 tons of alumina per day are $72 million for the dry grinding option and $66 million for the wet grinding option on a Marshall and Stevens chemical equipment index basis of 240.0. Specific geographic locations of plant and raw material sources are not assigned, but, since this process requires large quantities of both lime-stone and clay, the plant site is considered as variable with relation to the clay mine and limestone quarry. A nomograph is given to find operating costs at various delivered costs of clay and limestone. If the plant is located nearer the limestone quarry so that the delivered cost of clay is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $76.47 and $71.61 per ton of alumina for the dry grinding and wet grinding options, respectively. On the other hand, if the plant is located nearer the clay mine so that the delivered cost of clay is $1 per ton and the delivered cost of limestone is $2 per ton, the operating costs are $80.15 for dry grinding and $75.34 for wet grinding.

Jan 1, 1967